Kenmore 79075851301, 79075922300, 79075751102, 79072851300 Installation Guide

iNSTALLATiON AND SERVICE MUST BE PERFORMED BY A QUALiFiED iNSTALLER.
iMPORTANT: SAVE FOR LOCAL ELECTRICAL INSPECTOR'S USE.

READ AND SAVE THESE iNSTRUCTiONS FOR FUTURE REFERENCE.

if the information in this manual is not followed

exactly, a fire or explosion may result causing property
damage, personal injury or death.

FOR YOUR SAFETY:
= Do not store or use gasoline or other flammable vapors

and liquids inthe vicinity of this or any other appliance.

= WHAT TO DO iF YOU SMELL GAS:

• Do not try to light any appliance.
= Do not touch any electrical switch; do not use any phone

in your building.

• Immediately call your gas supplier from a neighbor's
phone. Follow the gas supplier's instructions.

e ALL RANGES

CAN TiP

• INJURYTO PERSONS

COULD RESULT

• iNSTALL ANTI=TIP
DEVICE PACKED WiTH

RANGE

• SEE iNSTALLATiON

iNSTRUCTiONS

• if you cannot reach your gas supplier, call the fire

department.

= Installation and service must be performed bya qualified

installer, service agency or the gas supplier.

RANGE
OVERALL
DIMENSIONS

47-3/4"

Maximum 36 + 1/8"

253/4"

Clearances and Dimensions

1. Location--Check location where
the range will be installed. Check

for proper electrical and gas
supply, and the stability of the

floor.

2. Dimensions that are shown must
be used. Given dimensions

provide minimum clearance.
Contact surface must be solid

and level.

PIN 316259313 (0112)

Wall on Either

Side of Range

Above 36"

Height.
* Note: 3" 30"

Clearance Minimum

if Equipped 2"

with 11000 or
greater BTU Burners.

FRONT

t Minimumto 14-13"-_1

18" Cabinets on Maximum Depth

Either Side for Cabinets

of Range. Above Range Top.

SIDE

VIEW

Provide Proper Fuel Type

Before Proceeding: Your range is preset to operate on natural gas only. This
model was shipped convertible from the factory with the necessary parts and

conversion instructions supplied,

DO NOT attempt toconvert this range to LP/Propane settings without

the proper LP/Propane conversion kit provided with the range orobtained from your
dealer, Follow all instructions provided with this conversion kit.

EspaSoI-Paginas9-16

Important Notes to the Installer

1. Read all instructions contained in these installation
instructions before installing range.

2. Remove all packing material from the oven compartments
before connecting the gas and electrical supply to the
range.

3. Observe all governing codes and ordinances.

4. Be sure to leave these instructions with the consumer.

Never leave children alone or unattended

in the area where an appliance is in use. As children grow,
teach them the proper, safe use of all appliances. Never leave
the oven door open when the range is unattended.

Stepping, leaning or sitting on the doors or

drawers of this range can result in serious injuries and
can also cause damage to the range.

Important Note to the Consumer

1. Keep these instructionswith your Use & Care Guide for

future reference.

IMPORTANT

SAFETY INSTRUCTIONS

Installation of this range must conform with local codes or, in

the absence of local codes, with the National Fuel Gas Code

ANSI Z223.1--1atest edition when installed in the United
States.

When installed ina manufactured (mobile) home, installation
must conform with the Manufactured Home Construction and

Safety Standard, Title 24 CFR, Part 3280 [formerly the
Federal Standard for Mobile Home Construction and Safety,
Title 24, HUD (Part 280)] or, when such standard is not
applicable, the Standard for Manufactured Home Installations,
ANSI/NCSBCS A225.1, or with local codes.

This range has been design certified by CSA International. As
with any appliance using gas and generating heat, there are
certain safety precautions you should follow. You will find

them in the Use & Care Guide, read it carefully.

= Be sureyour range is installed and grounded properly

by a qualified installer or service technician.

• This range must be electrically grounded in
accordance with local codes or, in their absence,

withthe National Electrical Code ANSI/NFPA No .70-
latest edition when installed in the United States.

See Grounding Instructions on page 5.

= Before installing the range in an area covered with

linoleum or any other synthetic floor covering, make
sure the floor covering can withstand heat at least
90°F above room temperature without shrinking,
warping or discoloring. Do not install the range over
carpeting unless you place an insulating pad or sheet of
1/4-inch thick plywood between the range and carpeting.

= Make sure the wall coverings around the range can

withstand the heat generated by the range.

= Do not obstruct the flow of combustion air at the

oven vent nor around the base or beneath the lower
front panel of the range. Avoid touching the vent

openings or nearby surfaces as they may become hot
while the oven is inoperation. This range requires fresh air

for proper burner combustion.

= Do not store items of interest to children in the

cabinets above the range. Children could be seriously
burned climbing on the range to reach items.

= To eliminate the need to reach over the surface

burners, cabinet storage space above the burners
should be avoided.

= Adjust surface burner flame size so it does not

extend beyond the edge of the cooking utensil.

Excessive flame is hazardous.

= Do not use the oven as astorage space. This creates

a potentially hazardous situation.
Never use your range for warming or heating the
room. Prolonged use of the range without adequate
ventilation can be dangerous.

= Do not store or use gasoline or other flammable

vapors and liquids near this or any other appliance.

Explosions or fires could result.

• Reset all controls to the "off" position after using a
programmable timing operation.

FOR MODELS WITH SELF-CLEAN FEATURE:

• Remove broiler pan, food and other utensils before
self=cleaning the oven. Wipe upexcess spillage. Follow
the cleaning instructions in the Use & Care Guide.

= Unlike the standard gas range, THIS COOKTOP IS

NOT REMOVABLE. Do not attempt to remove the
cooktop.

DO NOT MAKE ANY ATTEMPT TO

OPERATETHE ELECTRIC IGNITION OVEN DURING AN
ELECTRICAL POWER FAILURE. RESET ALL OVEN
CONTROLS TO "OFF" IN THE EVENT OF A POWER
FAILURE.

The electric ignitor will automatically re-ignite the oven
burner when power resumes ifthe oven thermostat control
was left in the "ON" position.

When an electrical power failure occurs during use, the
surface burners will continue to operate.

During a power outage, the surface burners can be lit with
a match. Hold a lighted match tothe burner, then slowlyturn
the knob to the LITE position. Use extreme caution when
lighting burners this way.

Before Starting

Tools You Will Need

For leveling legs and Anti-Tip Bracket:

Adjustable wrench or channel lock pliers

• 5/16" NutdrJver or Flat Head Screw Driver _J
Electric Drill & 1/8" Diameter Drill Bit (5/32" Masonry Drill
Bit if installing in concrete)

For gas supply connection:
= Pipe wrench

For burner flame adjustment:

• Phillips head and
blade-type screwdrivers

For gas conversion (LP/Propane or Natural):

• Open end wrench - 1/2" _:_", _

Additional Materials You Will Need

Gas line shut-off valve _.,._,

• Pipe joint sealant that resists action of LP/Propane gas

A new flexible metal appliance conduit (1/2" NPT x 3/4"
or 1/2" kD.) must be design certified byCSA International.

Because solid pipe restricts moving the range we
recommend using a new flexible conduit (4 to 5 foot
length) for each new installation and additional

reinstallations.

A. Locate the Bracket Using the Template- (Bracket may

be located on either the leftor right side of the range. Use
the information below to locate the bracket if template is
not available). Mark the floor or wall where left or right
side ofthe range will be located. If rear of range isagainst

the wall or no further than 1-1/4" from wall when installed,
you may use the wall or floor mount method. If molding

is installed and does not allow the bracket to fit flush
against the wall, remove molding or mount bracket to the

floor. For wall mount, locate the bracket by placing the
back edge of the template against the rear wall and the
side edge of template on the mark made referencing the
side of the range. Place bracket on top of template and
mark location of the screw holes in wall. If rear of range

is further than 1-1/4" from the wall when installed, attach
bracket to the floor. For floor mount, locate the bracket

by placing back edge of the template where the rear of
the range will be located. Mark the location of the screw
holes, shown in template.

B. Drill Pilot Holes and Fasten Bracket - Drill a 1/8" pilot

hole where screws are to be located. If bracket is to be
mounted to the wall, drill pilot hole at an approximate 20°

downward angle. If bracket is to be mounted to masonry
or ceramic floors, drill a 5/32" pilot hole 1-3/4" deep. The
screws provided may be used in wood or concrete

material. Use a 5/16" nut-driver or flat head screwdriver
to secure the bracket in place.

Always use the (2) new flare union adapters (1/2" NPTx
3/4" or 1/2" I.D.) supplied with the new flexible appliance
conduit for connection of the range.

Normal Installation Steps

1. Anti-Tip Bracket Installation Instructions

Important Safety Warning

To reduce the risk of tipping of the range, the range must be
secured to the floor by properly installed anti-tip bracket and
screws packed with the range. Failure to install the anti-tip
bracket will allow the range to tip over if excessive weight is
placed on an open door or if a child climbs upon it. Serious
injury might result from spilled hot liquids or from the range

itself.
If range is ever moved to a different location, the anti-tip

brackets must also be moved and installed with the range.
Instructions are provided for installation in wood or cement

fastened to either the floor or wall. When installed to the wall,
make sure that screws completely penetrate dry wall and are

secu red in wood or metal. When fastening to the floor orwall,
be sure that screws do not penetrate electrical wiring or
plumbing.

FASTEN BRACKET (FLOOR MOUNT|NG ONLY)