Kenmore 79070300706, 79070302703, 79073039310, 79073032310, 79073033310 Installation Guide

INSTALLATION AND SERVICE MUST BE PERFORMED BY

A QUALIFIED INSTALLER.

IMPORTANT: SAVE FOR LOCAL ELECTRICAL INSPECTOR'S USE.

READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.

This conversion kit must be installed by a qualified service technician in accordance

with the manufacturer's instructions and all applicable codes and requirements of the authority
having jurisdiction. Failure to follow instructions may result in fire, explosion or production of carbon
monoxide causing property damage, personal injury or loss of life. The qualified service agency is
responsible for the proper installation of this kit. The installation is not proper and complete until the
operation of the converted appliance is checked as specified in the manufacturer's instructions

supplied with this kit.

[F_ Before proceeding with the conversion, shut off the gas supply before disconnecting

electrical power to the range. Be sure both power supplies are off before installing the conversion
kit. Failure to do so could cause serious bodily injury.

When burners are converted from Natural to LP the BTU rating is as follows:
9,000 BTU* Natural Gas to 8,000 BTU* LP Gas. The LP converstion kit contains:

P/N Part Description Notes

4 316470401

1 316417511

*NOTE; For operation at elevations above 2000 ft.; appliance rating shall be reduced at the rate of 4 peicent for each 1000 if, above
sea level. After replacing the natural gas to LP orifices, be sure to keep the original factory installed natural gas orifices for future
range conversion back to natural gas:

Converting the appliance for use with LP/
Propane Gas

8,000* BTU LP Burner Orifices
LP Conversion Installation Instructions

marked 68L (.79mm orifice size)

c. Turn the pressure regulator cap over so the hollow end

faces toward the regulator as illustrated (See Fig. 1).

Before installing the brass pressure regulator cap, be sure

Tools Required"

to remove the dust protector and reinstall the ring portion
of the dust protector. The ring portion of the protector

1/2" Open End Wrench

MUST be installed. The ring portion of the dust protector

acts as a spacer between the regulator and brass

5/8" Open End Wrench

regulator cap when converted to LP.

d: Using a 5/8" open-end wrench tighten the pressure

1/4" Nutdriver
10mm Nutdriver

or

regulator cap until snug.

e: Snap the dust protector back over the pressure regulator

cap.

10mm Open End Wrench

1. Convert Pressure Regulator

Before proceeding with the conversion,

shut off the gas supply before disconnecting electrical
power to the range. Be sure both power supplies are

HOLLOW END

REGULATOR _

FOR NATURAL GAS _"

TOWARDS _ _

PRESSURE

REGULATOR

CAP

SPRING

SOLID END
TOWARDS

REGULATOR

FORLP. GAS

off before installing the conversion kit. Failure to do
so could cause serious bodily injury.

a. Lift and lock cooktop into raised position. Locate the gas

pressure regulator, The regulator is located atthe right rear
of the burner box and is attached to the manifold pipe.

b. Unsnap the plastic dust cap protector from the brass

pressure regulator cap. Use a 5/8" open-end wrench to
loosen and then remove the brass pressure regulator cap
(See Fig. 1). DO NOT remove the spring from the
pressure regulator.

Fig. 1

pin 316417511 (En/Fr) 0609

2. Convert Surface Burners for use with LP/

Propane Gas

a. With the cooktop still in the raised position, remove the

4 Venturi surface burners using a 1/4" nutdriver as
illustrated (See Fig. 2).

b. Using a 10mm nutdriver (or 10mm open-end wrench)

remove the 4 brass Natural Gas orifices from the ends
of the surface burner valves (See Fig. 3).

c. Replace the 4 brass Natural Gas orifices with the 4

brass LP Gas orfices supplied with this kit (the 4 LP
surface burner orfices are marked 68L).

d. Use a 10mm nutdriver (or 10mm open-end wrench) to

tighten the LP orifices until snug. DO NOT
OVERTIGHTEN.

e. Replace the 4 Venturi surface burners and secure in

place using a 1/4" nutdriver (See Fig. 2).

@@ @ @@

uY

Increase gas volume _,_

Increase flame size \

%J_L/_ Decrease gas volume

E__,_rJeCrease flame size

4_

Fig. 4

4. Reconnect Gas & Electrical Supply to
Appliance

Leak testing of the appliance shall be conducted according
to the Installation Instructions provided with the appliance.

Fig. 2

Fig. 3

3. Convert Oven Burner Orifice for LP/Propane

Gas (16,000 BTU*)

a. Removeoven broilerdrawerorlowerovenfrontpanel.
b. Locate the oven burner spud (See Fig. 4).
c. Using a 1/2" open=end wrench, turn down the adjustable

spud, which injects gas into the oven burner, until snug
against the LP metering pin (approximately 2-1/2 turns).

DO NOT OVERTIGHTEN.

Checking Manifold Gas Pressure

If it should be necessary to check the manifold gas
pressure, remove the burner and connect a manometer
(water gauge) or other pressure device to the top right front
burner orifice. Using a rubber hose with inside diameter of
approximately 1/4," hold tubing down tight over orifice. Turn
burner valve on. For an accurate pressure check, have at
least two (2) other surface burners burning. Be sure the gas
supply (inlet) pressure is at least one inch above specified
range manifold pressure. The gas supply pressure should
never be over 14"water column. When properly adjusted
the manifold water column pressure is 10" for LP/Propane
gas or 4" for Natural gas.

Do not use a flame to check for gas leaks.

a. Disconnectthe range and its individual shut-offvalve from

the gas supply piping system during any pressure testing
of that system at test pressures greater than 14" of water
column pressure (approximately 1/2" psig).

b. The appliance must be isolated from the gas supply piping

system by closing its individual manual shut-off valve
during any pressure testing of the gas supply piping
system at test pressures equal to orless than 14" of water
column pressure (approximately 1/2" psig).