Kenmore 79048873900, 79048879900, 79048834900, 79048839900, 79048789900 Installation Guide

...

iNSTALLATiON AND SERVICE MUST BE PERFORMED BY A QUALiFiED iNSTALLER.

Canada

iMPORTANT: SAVE FOR LOCAL ELECTRICAL iNSPECTOR'S USE.

READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.

FOR YOUR SAFETY: Do not store or use gasoline or other flammable vapors

and liquids in the vicinity of this or any other appliance.

United States

Your new wall oven has been designed to fit a limited variety of cutout sizes to make the job of installing easier. The first step of your installation should be to measure your

current cutout dimensions and compare them to the cutout dimensions chart below for your model. You may find little or no cabinet work being necessary.

Do not remove spacers (if equipped) on the side walls and/or on the back of the built=

in oven. These spacers center the oven in the space provided. The oven must be centered to prevent excess heat buildup that may result in heat damage or fire.

NOTES:

1. Base must be capable of supporting 150 pounds (68 kg) for 27" models and 200 pounds (90 kg) for 30" models.

2. Allow at least 21 " (53.3 cm) clearance in front of oven for door _,,_ _ r_ _-----__ " - depth when it is open. ' 'L'"Mi'n' _ _f

3. Dimension G (cutout depth)is critical I ' _ ;*

to the proper nsta at on of the bu t- n _. _ _-"-- _ -.....

oven. If the oven decorative trim does ' -'->_ i _.._ G .-_::;', for Cable

not butt against the cabinet or if noise ,, _.. _--_- ....... i /

• • ' • '_ H 1" '

s heard on convect on mode s ver fy _"--,

d mens on G to assure t s the requ red I

. .. "--'._? (69.1 cm) / :___-,</ 3"

' B -_-_ 27 3/16"

/_ "C _- _ ._ Hole

(]epm. , :_ I "_----_ _,_- ........ i (7.6 cm)

4. For a cutout height greater than ._ / I,, _ L_ '-_L:5_-_ I

27 /_o (70.6 cm) add one 2 ....... ..... _ ___

(5 cm)wide wood shim of Doo_O_.en _ " :l _:4.,. _ t

appropriate height to each 'seenote 2.... " D | _ "'_/.,,_

. . _ ; ........ / ' _ "1¼" \

side of the opening under the ......_ _b_ (3 2 cm) \

_ r_ bpacer (( /

t/_ / m)

appliance side rails. A _ k4in. /|

'"_ _q '_'_ Electrical

• Suggested distance from floor is 31 " (78.7 cm). 2" (5cm)Wide Wood V Junction Box Minimum required distance is 4 1/2"(11.4 cm). Spacerif Needed

.... Figure 1

27 and 30 Single Wall Ovens (Double ovens see Figure 2)

PRODUCT DIMENSIONS

A C D

27" (68.6 cm) Wall Oven 27 (68.6) 29%G (73.8) 24s/_ (62.5) 24V2 (62.2) 30" (76,2 cm) Wall Oven 30 (76,2) 29%G (73,8) 281/4(71,8) 24V2 (62,2)

CUTOUT DIMENSIONS AND CABINET WIDTH

MODEL:. Min;

27" (68.6 cm) Wall Oven 247/8 (63.2) 30" (76.2 cm) Wall Oven 28V2 (72.4)

Max.

251/4 (64.1)

29 (73.7)

Min; Max:.

23V2 (59.7) 271/4(69.2) 28V2 (72.4) 27V8 (68.9) Min 23V2 (59.7) 271/4(69.2) 28V2 (72.4) 30V_ (76.5) Min

All dimensionsare in inches(cm).

Printed in United States

P/N 318201530 (0901) Rev. A

English - pages 1-8

Espahol- p_iginas 9-16

Do not remove spacers (if equipped) on the side walls and/or on the back of the built-

in oven. These spacers center the oven in the space provided. The oven must be centered to prevent excess heat buildup that may result in heat damage or fire.

3" (7.6 cm)

Max.

Door Open

(seenote 2)

Junction Box

A r/ 2" (5 cm)Wide Wood-

NOTES:

1. Base must be capable of supporting 300 pounds (136 kg) for 27" models and 375 pounds (170 kg)

for 30" models.

2. Allow at least 21 " (53.3 cm) clearance in front of oven for door depth when it is open.

3. Dimension 6 (cutout depth) is critical to the proper installation of the built-in oven. If the oven decorative trim does not butt against the cabinet, or if noise is heard on convection models, verify dimension G to assure it is according to the required

dimension.

27* AND 30" DOUBLE OVENS (Single Ovens see Figure 1)

Spacerif Needed

4. For a cutout height greater than 491A'' (125.1 cm) add a 2" (5 cm) wide wood shim of appropriate height to each side of the opening under the appliance side rails.

* For Cutout height between 5113/16"(131.6 cm)

and 511s/16'' (131.9 cm) use the larger inferior trim supplied with the wall oven.

Figure 2

PRODUCT DIMENSIONS

MODEL .... C I

27" (68.6 cm) Wall Oven 27 (68.6) 50V2 (128.3) 24% (62.5) 24V2 (62.2) 30" (76.2 cm) Wall Oven 30 (76.2) 50V2 (128.3) 281/4(71.8) 24V2 (62.2)

CUTOUT DIMENSIONS AND CABINET WIDTH

27" (68.6 cm) Wall Oven 247/8 (63.2) 251/4(64.1) 231/2 (59.7) 487/8 (124.1) 497/8 (126.7) 27V8 (68.9) Min 30" (76.2 cm) Wall Oven 281/2 (72.4) 29 (73.7) 231/2(59.7) 487/8 (124.1) 497/8 (126.7)* 30V8 (76.5) Min

All dimensions are in inches (cm).

important Notes to the Installer

1. Read all instructions contained in these installation instructions before installing the wall oven.

2. Remove all packing material from the oven compartments before connecting the electrical supply

to the wall oven.

3. Observe all governing codes and ordinances.

4. Besure to leave these instructions with the consumer.

5. Oven door may be removed to facilitate installation.

6. THESEOVENS ARE NOT APPROVED FOR STACKABLEOR SIDE-BY-SIDE INSTALLATION.

important Note to the Consumer Keep these instructions with your Owner's Guide for

future reference.

IMPORTANT SAFETY

INSTRUCTIONS

• Be sure your wall oven is installed and grounded

properly by a qualified installer or service technician.

This wall oven must be electrically grounded in accordance with local codes or, in their absence,

with the National Electrical Code ANSI/NFPA No.70= latest edition in United Sates, or with CSA Standard C22.1, Canadian Electrical Code, Part 1, in Canada.

Stepping, leaning or sitting on the door of this wall oven can result in serious injuries and can also cause damage to the wall oven.

Never use your wall oven for warming or heating the room. Prolonged use of the wall oven without

ntilation can be dangerous.

The electrical power to the oven must be shut off while line connections are being made.

Failure to do so could result in serious injury or death.

ApplianCe ] Protedi0n I ApPlianCe' Pr0tection

Rating Watts Circuit Rating Watts Circuit

240V Recommended 208V Recommended

Lessthan4800W 20A Lessthan4100W 20A

4800W- 7200W 30A 4100W- 6200W 30A

7200W- g600W 40A 6200W- 8300W 40A

9600Wand + B0A 8300Wand+ B0A

Table A

3. Electrical Requirements

This appliance must be supplied with the proper voltage and frequency, and connected to an individual, properly grounded branch circuit, protected by a circuit breaker or fuse. To know the circuit breaker or fuse required by your model, see the serial plate to find the wattage consumption and refer to table A to get the circuit breaker or fuse amperage. Observe all governing codes and local ordinances

1. A 3-wire or 4-wire single phase 120/240 or 120/208 Volt, 60 Hz AC only electrical supply is required on a separate circuit fused on both sides of the line (time- delay fuse or circuit breaker is recommended). DO NOT fuse neutral. Consideration must be given for a combination built-in oven and cooktop refer to unit serial plate of each.

NOTE: Wire sizes and connections must conform with the fuse size and rating of the appliance in accordance

with the American National Electrical Code ANSI/NFPA No. 70-latest edition, or with Canadian CSA Standard

C22.1, Canadian Electrical Code, Part 1, and local codes and ordinances.

An extension cord should not be used

with this appliance. Such use may result in a fire, electrical shock, or other personal injury. If you need

a longer power cord you can order for purchase a 10' (3 m) power cord kit #903056-9010 by calling the Sears

Parts & Repair Center at 1-800-4-MY-HOME

1. Carpentry

Refer to figure 1 or 2 for the dimensions applicable to your appliance, and the space necessary to receive the oven. The oven support surface may be solid plywood or similar material, however the surface must be level from

side to side and from front to rear.

2. Adjusting Oven Height

Oven height can be adjusted with 2" (5 cm) wide wood shims when needed to fit into an existing cabinet cutout opening, when cutout height exceeds 27W16" (70.6 cm) for the single wall oven or 491/4"(125.1 cm) for the double wall oven (see Figure 1 or 2). Place shims of appropriate height beneath the oven side rails.

2. This appliance should be connected to the fused disconnect (or circuit breaker) box through flexible

armored or nonmetallic sheathed cable. The flexible armored cable extending from the appliance should

be connected directly to the junction box. The

junction box should be located as shown in figure 1

or 2 and with as much slack as possible remaining in the cable between the box and the appliance, so it can be moved if servicing is ever necessary.

3. A suitable strain relief must be provided to attach the flexible armored cable to the junction box.

Electrical Shock Hazard

• Electrical ground is required on this appliance.

• Do not connect to the electrical supply until

appliance is permanently grounded.

• Disconnect power to the junction box before making the electrical connection.

• This appliance must be connected to a grounded, metallic, permanent wiring system, or a grounding connector should be connected to the grounding terminal or wire lead on the appliance.

• Do not use a gas supply line for grounding the appliance.

Failure to do any of the above could result in a fire, personal injury or electrical shock.

4. Electrical connection

It is the responsibility and obligation of the consumer to contact a qualified installer to assure that the electrical installation is adequate and is in conformance with the National Electrical Code ANSI/NFPA No. 70-latest edition, or with CSA Standard C22.1, Canadian Electrical Code, Part 1, and local codes and ordinances.

Risk of electrical shock (Failure to

heed this warning may result in electrocution or other serious injury.) This appliance is equipped with copper lead wire. if connection is made to aluminum house wiring, use only connectors that are approved for joining copper and aluminum wire

in accordance with the National Electrical Code and local code and ordinances. When installing

connectors having screws which bear directly on the steel and/or aluminum flexible conduit, do no

tighten screws sufficiently to damage the flexible conduit. Do not over bend or excessively distort flexible conduit to avoid separation of convolutions en exposure of internal wires.

DO NOT ground to a gas supply pipe. DO NOT connect to electrical power supply until appliance is permanently grounded. Connect the ground wire before turning on the power.

(If your appliance is equipped with a

white neutral conductor,) This appliance is manufactured with a white neutral

power supply and a frame connected copper wire, The frame is grounded by connection of grounding

lead to neutral lead at the termination of the conduit, if used in USA, in a new branch circuit installation (1996 NEC), mobile home, recreational

vehicles, where local code do not permit grounding

trough the neutral (white) wire or in Canada, disconnect the white and green lead from each other and use ground lead to ground unit in

accordance with local codes, connect neutral lead to branch circuit=neutral conductor in usual manner

see Figure 4. If your appliance is to be connected to a 3 wire grounded junction box (US only), where local code permit connecting the appliance= grounding conductor to the neutral (white) see Figure 3.

NOTE TO ELECTRICIAN: The armored cable leads supplied with the appliance are UL-recognized for

connection to larger gauge household wiring. The insulation of the leads is rated at temperatures much higher than temperature rating of household wiring. The current carrying capacity of the conductor is governed by the temperature rating of the insulation around the wire, rather than the wire gauge alone.

Where local codes permit connecting the appliance= grounding conductor to the neutral (white) wire (US Only) (see figure 3):

1. Disconnect the power supply.

2. In the junction box: connect appliance and power supply cable wires as shown in Figure 3.

Cable from Power Supply

White Wire

(Neutral)

Wires-

Red

Wires

Box

(Neutral)

Ground Wire (Bare or Green Wire)

U.L.-Listed Conduit Connector (or CSA listed)

Cable from appliance

Figure 3

3-WIRE GROUNDED JUNCTION BOX

If oven is used in a new branch circuit installation (1996 NEC), mobile home, recreational vehicle, or where local codes DO NOT permit grounding

through the neutral (white) wire, the appliance frame MUST NOT be connected to the neutral wire

of the 4-wire electrical system. (see figure 4):

1. Disconnect the power supply.

2. Separate the green (or bare copper) and white appliance cable wires.

3. In the junction box: connect appliance and power supply cable wires as shown in Figure 4.

Cable from Power Supply

Wire __---"

Red _'_::_ hite Wire

F::::::::c:..

Ground

_/_ Black

wir;s

Vi/ire___( _

Ground

Bare or Gree

Wire) _-_- White Wire

Wire '__

Junction Box >:::75___U.L.-Listed Conduit

_-...... Connector (or CSA

Cable from appliance listed)

Figure 4

4-WIRE GROUNDED JUNCTION BOX

5. Cabinet Installation

Do not lift the oven by the door handle.

Heavy Weight Hazard

Use 2 or more people to move and install wall oven. Failure to follow this instruction can result in injury or damage to the unit.

OUnpack the wall oven. Remove the bottom trim taped

on the oven side panel.

OFind the 2 anti-tip mounting screws included in the

literature package.

_lnsert the oven into the cabinet opening. Slide oven

inward leaving 11/2"(3.8 cm) clearance between the oven and front of cabinet (see Figure 5).

Model and Serial Number Location The serial plate is located along the interior side trim of

the oven and visible when the door is opened. When ordering parts for or making inquires about your

oven, always be sure to include the model and serial numbers and a lot number or letter from the serial plate

on your oven.

i_ iiiiil;i_ i ....... iiiiiiiiiiii_i

Single Wall Oven Serial Plate Location

Double Wall Oven Serial Plate Location

_ 11/2" (3.8 cm)

clearance between unit

Figure 5

_Pull the armored cable through the hole for it in the

cabinet and toward the junction box while moving the appliance inward.

_Push the oven in and against the cabinet.

+ 11 hidden pages