Kenmore 79048082000, 79048089000, 79048183000, 79048182000, 79048179000 Installation Instruction

...

iNSTALLATiON AND SERVICE MUST BE PERFORMED BY A QUALiFiED

United States

iNSTALLER, iMPORTANT: SAVE FOR LOCAL ELECTRICAL iNSPECTOR'S USE.

READ AND SAVE THESE iNSTRUCTiONS FOR FUTURE REFERENCE.

FOR YOUR SAFETY: Do nat store or use gasollne or other flammable

vapors and liquids in the vicinity of this or any other appliance. Your new wall oven has been designed to fit a limited variety of cutout sizes to make

the jab of installlng easier. The first step of your installatlon should be to measure your current cutout dimensions and compare them to the cutout dimensions chart below far

your model. You may find lltfle or no cabinet work being necessary.

Do not remove spacers (if equipped) on the side walls and/or an the back of the built-ln oven. These spacers center the oven in the space provided. The oven must be centered to prevent excess heat buildup that may result in heat damage or fire.

NOTES:

|. Bose must be capable of supporting 150 pounds (68 kg) for 27" models

and 200 pounds (90 kg) for 30" models.

2. Allow at least 21" (53.3cm) clearance in front of oven for door 1" (2.5 cm) depth when it is open. Min.

3. Dimension G (cutout depth) is critical <L to the proper installation of the built-

in oven. If the oven decorative trim does not butt against the cabinet, or if I H

noise is heard on convection models, B | verify dimension G to assure it is the I required depth, t

4. For o cutout height greater

than 2713/16" (70.6cm) odd ......._ 31"*

i| . . ._--'"

one 2 (5cm) wide wood shim Doc)r Open of appropriate height to each

side of the opening under the appliance side roiis. Suggested distance from floor

is 31" (78.7cm). Minimum required distance is 4 1/2" (11.4cm)

27" and 30" Single Wall Ovens (Double ovens see Figure 2)

(see note 2

2" (5 crn) Wide Wood

Spacer if Needed

Figure |

Canada

Junction Box

Elecfrlcal

27" (68.6cm) 27 (68.6) 29t/16(73.8) 24s/8 (62.5) 241/2 (62.2) 30" (76.2cm) 30 (76.2) 29t/16(73.8) 28t/4 (71.8) 241/2(62.2)

MODEL G (rain.) I

Min. Max. Min. Max.

27" (68.6cm) 247/8 (63.2) 251/4(64.1) 231/2(59.7) 275/_ (69.4) 281/2(72.4) 271/8 (68.9) Min. 30" (76.2cm) 281/2(72.4) 29 (73.7) 231/2(59.7) 275/_ (69.4) 281/2(72.4) 301/8 (76.5) Min.

Aii dimensions ore in inches (cm).

Printed in United States

CUTOUT DIMENSIONS AND CABINET WIDTH

F H

P/N 318201544 (1005) Rev. A

English - pages 1-8

Espa_ol - p6ginas 9-16

Do not remove spacers (if equipped) an the side walls and/or an the back of the built-ln oven. These spacers center the oven in the space provided. The oven must be centered to prevent excess heat buildup that may result in heat damage or fire.

1"(2.5cm)

Min.

485/8" H

(123.5cm)

Door Open

27" AND 30" DOUBLE OVENS (Single Ovens see Figure 1)

_- Spacer

NOTES:

I. Base must be capabie of supporting 300 pounds

(136 kg) for 27" models and 375 pounds (170 kg)

for 30" models.

2. Allow at least 21" (53.3 cm) clearance in front of

oven for door depth when it is open.

3. Dimension G (cutout depth) is critical to the

proper installation of the built-in oven. If the oven decorative trim does not butt against the cabinet, or if noise is heard on convection models,

verify dimension G to assure it is according to the

required dimension.

11½"

(29.2

2" (5 cm) Wide Wood

Spacer if Needed

Figure 2

For a cutout height greater than 491,,_'' (125.1 cm) add a 2" (5 cm) wide wood shim of appropriate height to each side of the opening under the appliance side rails.

For Cutout height between 5113/16"(131.6 cm) and

51_s/16"(131.9 cm), you can order a larger inferior trim kit by calling the Service Center.

Trim 27" 903114-901S 903114-9010 903114-9011 Trim 30" 903114-910S 903114-9100 903114-9101

Hole for Cable

Electrlcal

Junction Box

Stainless Steel Black White

27" (68.6crn) 27 (68.6) 501/2(128.3) 24s/_ (62.5) 24V2 (62.2) 30" (76.2cm) 30 (76.2) 50V2 (128.3) 28V4 (71.8) 241/'2(62.2)

CUTOUT DIMENSIONS AND CABINET WIDTH

F H

MODEL G (rain.) I

Min. Max. Min. Max.

27" (68.6crn) 247/_ (63.2) 25V4 (64.1) 231/2 (59.7) 487/_ (124.1) 497/_ (126.7) 27_/_ (68.9) Min. 30" (76.2crn) 281/2(72.4) 29 (73.7) 231/2 (59.7) 487/_ (124.1) 497/_ (126.7) 30_/_ (76.5) Min.

All dimensions are _ninches (cm).

importantNotestothe Installer

1. Readaiiinstructionscontainedintheseinstallation instructionsbeforeinstallingthewalloven.

2. Removeallpackingmatedalfromtheoven compartmentsbeforeconnectingtheelectrical supply

to the waft oven.

3. Observe all governing codes and ordinances.

4. Be sure to leave these instructions with the consumer.

5. Oven door may be removed to facilitate installation.

6. THESE OVENS ARE NOT APPROVED FOR STACKABLE OR SiDE=BY=SIDE iNSTALLATION.

important Note to the Consumer Keep these instructions with your Owner's Guide for future

reference,

iMPORTANT SAFETY INSTRUCTIONS

° Be sure your wall oven is installed and grounded

properly by a qualified installer or service technician.

° This wahl oven must be electrically grounded in

accordance with local codes or, in their absence,

with the National Electrlcal Code ANSI/NFPA No.70=

latest edition in United Sates, or with CSA Standard C22.1, Canadian Electrical Code, Part 1, in Canada.

Stepping, leaning or sitting on the door

of this wall oven can result in serious injuries and can also cause damage to the wall oven.

° Never use your wall oven for warming or heating

the room. Prolonged use of the wail oven without adequate ventilation can be dangerous.

The electrlcal power to the oven must

be shut off while llne connections ore being mode.

Failure to do so could result in serious injury or death.

1. Carpentry

Refer to figure 1 or 2 for the dimensions applicable to your appliance, and the space necessary to receive the oven. The oven support surface may be solid plywood or similar material, however the surface must be level

from side to side and from front to rear.

2. Adjusting Oven Height

Oven height can be adjusted with 2" (5 cm) wide wood shims when needed to fit into an existing cabinet cutout

opening, when cutout height exceeds 2713/16" (70.6 cm) for the single wail oven or 491.4" (125.1 cm) for

the double wail oven (see Figure 1 or 2). Place shims of appropriate height beneath the oven side rails.

3. Electrical Requirements

This appliance must be supplied with the proper voltage and frequency, and connected to an individual, properly grounded branch circuit, protected by a circuit

breaker or fuse. To know the circuit breaker or fuse required by your model, see the serial plate to find the

wattage consumption and refer to table A to get the circuit breaker or fuse amperage.

n_ I B

Appliance Protection Appliance Protection

Rating Watts Circuit Rating Watts Circuit

240V Recommended 208V Recommended

Lessthan 4800W 20A Lessthan 4100W 20A

4800W - 7200W 30A 4100W - 6200W 30A

7200W - 9600W 40A 6200W - 8300W 40A

9600W and + 50A 8300W and + 50A

Observe aft governing codes and local ordinances

1. A 3-wire or 4-wire single phase 120/240 or 120/208 Volt, 60 Hz AC only electrical supply is required on

a separate circuit fused on both sides of the line (red and black wires). A time-delay fuse or circuit breaker is recommended. DO NOT fuse neutral (white wire). Only certain cooktop models may be installed over certain built-in electric oven models. Approved cooktops and built-in ovens are listed by the MFG ID number (see the insert sheet included in the literature package).

NOTE: Wire sizes and connections must conform with the fuse size and rating of the appliance in accordance

with the American National Electrical Code ANSI/NFPA No. 70-latest edition, or with Canadian CSA Standard C22.1, Canadian Electrical Code, Part 1, and local codes

and ordinances.

with this appllance. Such use may result in a fire,

electrlcal shock, or other personal injury. If you need a longer power cord you can purchase a 10' (3 m) power

cord kit #903056-9010 by calling the Service Center.

2. These appliances should be connected to the fused

disconnect (or circuit breaker) box through flexible armored or nonmetallic sheathed cable. The flexible

armored cable extending from the appliance should be connected directly to the junction box. The

junction box should be located as shown in Figure

1 or Figure 2 and with as much slack as possible remaining in the cable between the box and the appliance, so it can be moved if servicing is ever necessary.

3. A suitable strain relief must be provided to attach

the flexible armored cable to the junction box.

n H

Table A

An extension cord should not be used

Electrical Shock Hazard

* Electrical ground is required on this appliance. * Do not connect to the electrical supply until appliance is

permanently grounded.

* Disconnect power to the junction box before making the

electrical connection.

" This appliance must be connected to a grounded, metallic,

permanent wiring system, or a grounding connector should

be connected to the grounding terminal or wire lead on

the appliance0

* Do not use a gas supply line for grounding the appliance.

Failure to do any of the above could result in a fire,

personal injury or electrical shock.

In cold weather shipping and storage conditions, make sure that oven is in final location at least three (3) hours before switching on power. Switching on power while oven is still cold may damage

the oven controls.

4° Electrical connection

It is the responsibility and obligation of the consumer to contact a qualified installer to assure that the electrical installation is adequate and is in conformance with the National Electrical Code ANSI/NFPA No. 70- latest edition, or with CSA Standard C22.1, Canadian Electrical Code, Part 1, and local codes and ordinances.

Risk of electrical shock (Failure to heed thls warning may result in electrocution or other serious injury.) This appliance is equipped wlfh copper lead wire. If connection is made to aluminum

house wiring, use only connectors that are approved for joining copper and aluminum wire in accordance

wlfh the National Electrical Code and local code and ordinances. When installing connectors having screws

which bear directly on the steel and/or aluminum flexible conduit, do no tighten screws sumclently to damage the flexible conduit. Do not over bend or

excessively distort flexible conduit to avoid separation of convolutions en exposure of internal wires.

(If your appliance is equipped wlth a white neutral conductor.) This appliance is manufactured with a white neutral power supply and a frame connected copper wire.

The frame is grounded by connection of grounding lead to neutral lead at the termination of the conduit, if used in USA, in a new branch circuit installation (1996 NEC), mobile home, recreational vehicles, where Iocag code do not permit grounding trough the neutral

(white) wire or in Canada, disconnect the white and green lead from each other and use ground lead to ground unit in accordance wlfh local codes, connect

neutral lead to branch clrcult=neufral conductor in usual manner see Figure 4. If your appliance is to

be connected to a 3 wire grounded junction box (US only), where local code permit connecting the

appllance=groundlng conductor to the neutral (white) see Figure 3.

NOTE TO ELECTRICIAN: The armored cable leads supplied with the appliance are UL-recognized for

connection to larger gauge household wiring. The insulation of the leads is rated at temperatures much higher than temperature rating of household wiring. The current carrying capacity of the conductor is governed by the temperature rating of the insulation around the wire, rather than the wire gauge alone.

Where local codes permit connecting the appllance= grounding conductor to the neutral (white) wire (US Only) (see figure 3):

1. Disconnect the power supply.

2. In the junction box:

connect appliance and power supply cable wires as shown in Figure 3.

Cable from Power Supply

White Wire _ I

(Neutral) _ :::........._--- _-_------W"

\l ;":_:_'- :<_ _ z/ _i ires m

Black

Red : a-- /

DO NOT ground to a gas supply pipe. DO NOT connect to electrical power supply until appliance is permanently grounded. Connect the ground wire before turning on the power.

'/'¢X'v-'A ) ........i j| --_Whit

/_ .......! S "White Wire

/ k_ _ (Neutral)

Ground Wire ---I _........ U.L0-ListedConduit

(Bare or Green Wire) ,_L Connector (or CSA listed)

Cable from appNance

Figure 3

3-WIRE GROUNDED JUNCTION BOX

If oven is used in a new branch circuit installation

(1996 NEC), mobile home, recreatlonaJ vehicle, or where local codes DO NOT permit grounding through the neutral (white) wire, the appliance frame MUST

HOT be connected to the neutral wire of the 4-wire electrical system. (see figure 4):

1. Disconnect the power supply.

2. Separate the green (or bare copper) and white appliance cable wires.

3. In the junction box: connect appliance and power supply cable wires as shown in Figure 4.

Cable from Power Supply

Ground Wire

_'__ _'_J_ w w

Red \p____c/_ hite ire

Ground Wire ___'_ (Bare or Green-- _

Wire) J _ ire

Junction Box _ _- .... U.L.-Listed Conduit

4-WIRE GROUNDED JUNCTION BOX

j S

_' Connector (or CSA

Cable from appliance listed)

Figure 4

5. Cabinet Installation

oven

Do nat lift the the door handle.

Heavy Weight Hazard

Use 2 or more people to move and install wall oven.

Failure to follow this instruction can result in injury or damage

to the unit.

1. Unpack the wall oven. Remove the bottom trim taped on the oven side panel.

2. Find the 2 anti-tip mounting screws included in the literature package.

3. Insert the oven into the cabinet opening. Slide oven inward leaving 11/2" (3.8cm) clearance between the

oven and front of cabinet (see Figure 5).

Model and Serial Number Location

The serial plate is located along the interior side trim of the oven and visible when the door is opened.

When ordering parts for or making inquires about your oven, always be sure to include the model and serial numbers and a Jot number or letter from the serial plate

on your oven.

Single Wall Oven Serial Plate Location

Double Wall Oven Serial Plate Location

cm)

clearance between unit

Figure 5

4.Pull the armored cable through the hole for it in the cabinet and toward the junction box while moving the appliance inward.

5. Push the oven in and against the cabinet.

+ 11 hidden pages