Kenmore 79047859403, 79047859404, 79047859405, 79047859406, 79047859407 Installation Guide

...

INSTALLATION AND SERVICE MUST BE PERFORMED BY A QUAUFIED INSTALLER.

IMPORTANT: SAVE FOR LOCAL ELECTRICAL INSPECTOR'S USE.

READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.

FOR YOUR SAFETY: Do not store or use gasoline or other flammable vapors and liquids in

the vicinity of this or any other appliance. Your new wall oven has been designed to fit a Hmited variety of cutout sizes to make the job of installing

easier, The first step of your installation should be to measure your current cutout dimensions and compare them to the cutout dimensions chart beJow for your model You may find JittJe or no cabinet work is necessary.

Do not remove spacers (if equipped) on the side walls and/or on the back of the built-in

oven, These spacers center the oven in the space provided, The oven must be centered to prevent excess heat buildup that may result in heat damage or fire.

NOTES: Hole for

-- [ _ Cable

1. Base must be capable of supporting 225 pounds (102 kg). I" (2.5 cm)

2. Allow at least 21 " (53.3 cm) clearance in front of oven for door Min / ........-'--_- / ' .

(r ght or

depth when t s open / _---___ /left side

3. Dimension 6 ((utout depth)is _ L_ __ / depend, ing

.... ' -- _ .... on moae_

critical to the proper installation of _, "_:--_ ........ ! /

the built-in oven. If the oven i _ " G_' /

decorativetr mdoesnotbu t :......" ! /

against the cabinet verify ii........ ', H /

_r(_lte:s:°de_ttk:i assure it is t he B _ _ iOoI Sc/ll:" "<",-, _

.......... : J -_ (292 cm) r_-_.._ _q_ Max.

DoorOpen "-_',,_ _ . -,, I_ _-_ i_

* Suggested distance from floor ......... _ ..... _ <Min/ Junction Box

is 11Y2" (29.2 cm). A.,,.._ Spacer if Needed Minimum required distance is 4 Figure 1

_/2" (11.4 cm)

(seenote 2) .'_ D_ Spacer _'-_b_ -(3.2cm) "-_ Electrical

"'" \-, 2 (5 cm) Wide Wood _" _ (right or left side)

27" (68.6 cm)Wall Oven 27 (686)

30" (762 crn) Wall Oven 30 (76.2)

27" (686 crN Wall Oven 247s (63.2) 25¼ (64.1)

30" (762 cm) Wall Oven 28Y_ (724) 29 (737)

All dimensions are stated in inches and (cm)

42s_ (108.6) 24s/s (62.5)

42s_ (108.6) 28¼ (71 8)

23V2(597) 41% (1045)

23V2 (597) 41Vs (1045)

41¼ (104.8)

24Y_ (62 2)

27Vs (689) Min

30Vs (765) Min

P/N 318201518 (0409) Rev A

English - pages 1-6

Espatlol - p_ginas 7-12

_mportant Notes to the _nstaller

1. Readall instructions contained in these installation instructions before installing the combination oven.

2. Remove all packing material from the oven compartments before connecting the electrical supply

to the wall oven.

3. Observe all governing codes and ordinances.

4. Besure to leavethese instructions with the consumer.

5. Oven door may be removed to facilitate installation.

6. THS COMBINATION OVEN tS NOT APPROVED FOR STACKABLE OR SIDE-BY-SIDE INSTALLATION.

Important Note to the Consumer

Keep these instructions with your Owner's Guide for future reference. Do not discard oven removal tools found in the

literature bag.

IMPORTANTSAFETYINSTRUCTIONS

• Be sure your combination oven is installed and

grounded properJy by a qualified installer or service technician.

This walt oven must be eJectricaJly grounded in accordance with tocal codes or, in their absence, with the National EJectricaJCode ANSJ/NFPA

No.70- tatest edition in United Sates, or with CSA Standard C22.1, Canadian Electrical Code, Part 1, in

Canada.

Stepping, teaning or sitting on the

door of this wall oven can result in serious injuries and can atso cause damage to the wait oven.

1, Carpentry

Refer to figure 1 for the dimensions applicable to your appliance, and the space necessary to receive the combination oven. The oven support surface may be solid plywood or similar material, however the surface

must be leveled from side to side and from front to rear.

2. Electrican Requirements

This combination oven must be supplied with the proper voltage and frequency, and connected to an individual,

properly grounded branch circuit, protected by a circuit

breaker or fuse, having amperage as noted on the rating

plate (the rating plate is located on the side trim).

Observe aH governing codes and Jocal ordinances

1. A 3-wire or 4-wire single phase 120/240 or ! 20/208 Volt, 60 Hz AC only electrical supply is required on

a separate circuit fused on both sides of the line (time-delay fuse or circuit breaker is recommended).

DO NOTfuse neutral. The fuse size must not exceed the circuit rating of the appliance specified on tile nameplate.

2. Tile combination oven can consume up to 5200W when both ovens are operating. Use a circuit

breaker of 30 Amp with wire gauge #8 AWG.

NOTE: Wire sizesand connections must conform with the fuse size and rating of the appliance in accordance

with the American National Electrical Code ANS!/NFPA

No. 70qatest edition, or with Canadian CSA Standard

C22.1, Canadian Electrical Code, Part 1, and local codes and ordinances.

Never use your wail oven for warming or heating the room. Prolonged use of the wall oven without adequate ventilation can be dangerous.

The eJectrical power to the oven must

be shut off while Hne connections are being made. Failure to do so coutd resutt in serious injury or

death.

An extension cord shouJd not be used

with this appliance. Such use may result in a fire, electrical shock, or other personaJ injury.

3. This combination oven should be connected to tile fused disconnect (or circuit breaker) box through

flexible armored or nonmetallic sheathed cable. The flexible armored cable extending from the appliance

should be connected directly to the junction box. The

junction box should be located as shown in Figure 1

and with as much slack as possible remaining in the cable between the box and tile appliance, so tile latter can be moved if servicing is ever necessary.

4. A suitable strain relief must be provided to attach the flexible armored cable to the junction box.

Electrical Shock Hazard

• Electrical ground [s required on this appliance.

• Do not connect to the electrical supply until appliance is permanently grounded.

• Disconnect power to the junction box before

making the electrical connection.

• This appliance must be connected to a grounded, metallic, permanent wiring system, or a grounding connector should be connected to the grounding terminal or wire [ead on the appliance.

• Do not use a gas supply line for grounding the appliance.

Failure to do any of the above could result in a

fire, personal injury or electrical shock.

In cold weather shipping and storage

conditions, make sure that oven is in final location at

least three (3) hours before switching on power.

Switching on power while oven is still cold may damage tile oven controls.

Where local codes permit connecting the appJiance- grounding conductor to the neutral (white) wire (see figure 2}:

1. Disconnect tile power supply.

2. In the circuit breaker, fuse box or junction box: connect appliance and power supply cable wires as shown in Figure 2.

Cable from Power Supply

White Wire (Neutral)

Red

Wires

Box

(Neutral)

Ground Wire U.L.-Listed Conduit (Bare or Green Wire) Connector (or CSA listed)

Cable from appliance

Figure 2

3-WtRE GROUNDED JUNCTION BOX

3. Electrical connection

It isthe responsibility and obligation of the consumer to

contact a qualified installer to assure that tile electrical

installation is adequate and is in conformance with tile National Electrical Code ANSI/NFPA No. 70datest

edition, or with CSA Standard C22.1, Canadian

Electrical Code, Part 1, and local codes and ordinances.

Electrical ground is required on this appliance,

This appliance is equipped with a copper conductor flexible cable. If connection is made to aluminum house

wiring, use only special connectors which are approved for joining copper and aluminum wires in accordance

with National Electrical Code and local codes and ordinances.

This appliance is manufactured with a white neutral

power supply wire and a frame connected green or bare

copper grounding wire.

Improper connection of aluminum

house wiring to copper leads can result [n a short circuit or fire. Use onIy connectors designed for

joining copper to aluminum, and fo[tow the

manufacturer's recommended procedure doseJy.

You may not ground the oven

through the neutral (white} wire if oven is used in a new branch circuit installation (!996 NEC), mobiJe home, recreational vehicle, or where local codes do not permit grounding through the neutral (white) wire. When grounding through the neutral (white) wire is prohibited, you must use a 4-wire power supply cable. See Figure 3. Failure to heed this warning may result in electrocution or other serious personal injury.

tf oven is used in a new branch drcuit installation (!996 NEC), mobile home, recreational vehicle, or where local codes DO NOT permit grounding

through the neutral (white) wire (see figure 3):

1. Disconnect the power supply.

2. Separate the green (or bare copper) and white appliance (:able wires.

3. In the circuit breaker, fuse box or junction box: connect appliance and power supply cable wires as shown in Figure 3.

Cable from Power Supply

Wires

Black

Ground Wire (Bare or

Wire)

Junction Box U.L.-Listed Conduit

Connector (or CSA listed)

Cable from appliance

Figure 3

4-WIRE GROUNDED JUNCTION BOX

Wires]

Heavy Weight Hazard

Use 2 or more people to move and install this

combination oven.

Failure to follow this instruction can result in injury

or damage to the unit.

4. Cabinet Installation

The combination oven can tip when

the door is open. The mounting brackets supplied with the oven must be attached to the cabinet and

the appliance to prevent tipping of the wail oven and injury to persons.

Mounting Brackets Installation Instructions

1. Unpack the wall oven. Remove the bottom trim taped on the oven side panel. Find the 2 mounting brackets and screws included in the literature package.

2. Install the mounting bracket in the wall cabinet as shown in Figure 4. Note: To prevent damage to cabinet,

it isrecommended to drill 1/16" (0.16 cm) dia. pilot holes before installing the mounting brackets.

DO NOT ground to a gas supply pipe. DO NOT connect to electrical power supply until appliance is permanently grounded. Connect the ground wire before turning on tile power (Figure 3).

If connecting to a 4-wire electrical

system (mobile homes), the appliance frame MUST NOT be connected to the neutral wire of the 4-wire

electrical system.

NOTE TO ELECTRICIAN: The armored cable leads supplied with tile appliance are UUrecognized for

connection to larger gauge household wiring. The insulation of the leads is rated at temperatures much higher than temperature rating of household wiring. The current carrying capacity of the conductor is governed by the temperature rating of the insulation around the wire, rather than tile wire gauge alone.

22 3/16" *

(56.4 cm)

* If wood spacers are needded (seefigure1 ) please calculate this dimension from the top of the spacer to

the middle of the mounting bracket.

iiii ! iii!¸

Figure 4

3.Insert the oven into the cabinet opening. Slide oven

inward leaving !_/2" (3.8 cm) clearance between the oven and front of cabinet (seeFigure 5). Pull the armored cable through the hole for it in the cabinet and toward the junction box while moving the appliance inward.

+ 8 hidden pages