Kenmore 790.46991, 790.46994, 790.46999 Use & Care Manual
TM
lectric Range
Slide-in models
Estufa el_ctrica
Modelos deslizables
/,,j_:,, :::_,,,J!/_,.,d dc do
Models/Modelos 790.46992, 790.46991, 790.46994,
790.46999
kS_
318200828(0109)Rev.B Sears Roebuck and Co., Hoffman Estates, IL60179 U.S.A. www.sears.¢om
Table of Contents
Product Record ................................................................ 2
Slide-in Range Warranty ................................................. 2
IMPORTANT SAFETY INSTRUCTIONS .............................. 3-5
Selecting Surface Cooking Utensils ................................ 6
Specialty Pans & Trivets ................................................... 6
Canning Tips & Information ........................................... 7
Range Features ................................................................ 8
Control Pad Functions ..................................................... 9
Temperature Conversion ................................................. 9
Setting the Clock ............................................................ 10
Surface Cooking ........................................................ 11-12
Oven Vent(s) and Racks .................................................. 12
Changing Oven Light ..................................................... 12
Setting Oven Controls ............................................... 13-17
• To Setor Change Temperature for Normal Baking ....... 13
• Timed Bake Feature ................................................... 14
• Oven Baking Informations ........................................... 15
• Air Circulation inthe Oven .......................................... 15
• Broil ........................................................................... 16
• Broiling Informations ................................................... 17
Oven Cleaning ........................................................... 18-19
General Cleaning ....................................................... 20-24
Recalibrating Your Oven Temperature .......................... 24
Avoid Service Checklist ............................................. 25-26
Espa5ol ........................................................................... 27
Sears Service .................................................... Back Cover
Product Record
Inthis space below, record the date of purchase, model and serial number of your product. You will find the model and serial
number printed on an identification plate. The identification plate is located on the left side of the range and are visible when
the oven door isopen or on the inside of the drawer along the side of the frame.
Model No. 790. Date of Purchase
Serial No.
Savethese instructions and your sales receipt for reference.
Slide-in Range Warranty
FULLONE YEAR WARRANTY ON ALL PARTS
If, within one year from the date of installation, any part fails to function properly due to a defect in material
or workmanship, Sears will repair or replace it, at our option, free of charge.
Your ceramic glasssmoothtop iscovered by an additional 2nd through 5th year limited warranty. This
warranty provides for replacement for any defective surface heating element, deteriorated rubberized-silicone
seal, or glass smoothtop that cracks due to thermal breakage. Damage or breakage due to customer abuse is
not covered by this warranty.
If the product issubjected to other than private residential use, the above warranty is effective for only 90
days.
WARRANTY SERVICE ISAVAILABLE BY CONTACTING SEARS AT 1-800-4-MY-HOME®.
This warranty givesyou specific legal rights, and you may also have other rights which vary from state to state.
SearsRoebuck and Co., Dept. 817WA Hoffman Estates, IL 60179
WE SERVICEWHAT WE SELL
Your purchase has added value because you can depend on SearsHomeCentral® for service. With over
12,000 trained repair specialists and accessto over 4.2 million parts and accessories, we have the tools, parts,
knowledge and skills to ensure our pledge: We Service What We Sell.
Sears Maintenance Agreements
Your Kenmore appliance is designed, manufactured and tested to provide years of dependable operation. Yet
any major appliance may require service from time to time. The SearsMaintenance Agreement offers you an
outstanding service program, affordably priced.
The Sears Maintenance Agreement
• Isyour way to buy tomorrow's service at today's price.
• Eliminates repair bills resulting from normal wear and tear.
• Provides for non-technical and instructional assistance.
• Even if you don't need repairs, provides an annual Preventive Maintenance Check,
at your request, to ensure that your appliance is in proper running condition.
Some limitations apply. For more information, call 1-800-827-6655.
For information concerning SearsCanada Maintenance Agreements, call 1-800-361-6665.
IMPORTANT SAFETY INSTRUCTIONS
Read all instructions before using this appliance.
Save these instructions for future reference.
This manual contains many important safety messages. Always read and obey all safety messages.
The safety symbol [] calls your attention to safety messagesthat inform you of hazards that can kill or hurt you or others, or
cause damage to the product.
Indicates an imminently hazardous situation which, if not avoided may result in death or serious injury.
Indicates an imminently hazardous situation which, if not avoided may result in minor or moderate injury, or
product damage.
All safety messageswill identify the hazard, tell you how to reduce the chance of injury, and tell you what can happen if the
instructions are not followed.
• All ranges can tip.
• Injury to persons could result.
• Install anti-tip device packed with range.
• See Installation Instructions.
To reduce the risk of tipping, the range must be secured by properly installed anti-tip
bracket(s) provided with the range. To check if the bracket(s) is installed properly,
remove the lower panel or storage drawer and verify that the anti-tip bracket(s) is engaged. Refer
to the Installation Instructions for proper anti-tip bracket(s) installation.
Z
O
Z
Remove all tape and packaging before using the
range. Destroy the carton and plastic bags after unpack-
ing the range. Never allow children to play with packag-
ing material.
Proper Installation-Be sure your appliance isprop-
erly installed and grounded by a qualified technician
in accordance with the National Electrical Code
ANSI/NFPA No. 70 latest edition, and local code
requirements. Install only per installation instructions
provided in the literature package for this range.
Ask your dealer to recommend a qualified technician and an
authorized SearsService Center. Know how to disconnect
the power to the range at the circuit breaker or fuse box in
case of an emergency.
User servicing--Do not repair or replace any part of
the appliance unless specifically recommended in
the manuals. All other servicing should be done only by
a qualified technician, This may reduce the risk of
personal injury and damage to the range.
• Never modify or alter the construction of a range by
removing leveling legs, panels, wire covers, anti-tip
brackets/screws, or any other part of the product.
Stepping, leaning or sitting on the door
or drawer of this range can result in serious injuries
and also cause damage to the range. Do not allow
children to climb or play around the range. The weight of a
child on an open door may cause the range to tip, resulting
in serious burns or other injury. An open drawer, when hot,
may cause burns.
Do not use the oven or warmer drawer
(if equipped) for storage.
Do not store items of interest to children
in the cabinets above a range. Children climbing on the
range to reach items could be seriously injured.
Never use your appliance for warming
up or heating up the room.
Storage in or on appliance--Flammable materials
should not be stored in an oven, near surface units
or in the drawer (if equipped). This includespaper,
plastic and cloth items, such as cookbooks, plasticware
and towels, aswell as flammable liquids. Do not store
explosives, such as aerosol cans, on or near the appli-
ance. Flammable materials may explode and result in fire
or property damage.
IMPORTANT SAFETY INSTRUCTIONS
Do not leave children alone--Children should not be
left alone or unattended in the area where appliance
is in use. They should never be allowed to sit or stand
on any part of the appliance.
DO NOT TOUCH SURFACEUNITS,AREAS NEARTHESE
UNITS, OVEN HEATING ELEMENTSOR INTERIOR
SURFACESOF THE OVEN ORWARMER DRAWER (if
equipped). Both surface and oven heating elements
may be hot even though they are dark in color. Areas
near surface units may become hot enough to cause
burns. During and after use, do not touch, or let clothing
or other flammable materials touch these areas until they
have had sufficient time to cool. Among these areas are
the cooktop, surfaces facing the cooktop, the oven vent
openings and surfaces near these openings, oven door
and window.
Wear proper apparel--Loose-fitting or hanging
garments should never be worn while using the
appliance. Do not let clothing or other flammable
materials contact hot surfaces.
• Do not use water or flour on grease fires--Smother
the fire with a pan lid, or use baking soda, a dry
chemical or foam-type extinguisher.
• When heating fat or grease, watch it closely. Fat or
grease may catch fire if allowed to become too hot.
Use only dry potholders--Moist or damp potholders
on hot surfaces may result in burns from steam. Do
not let potholders touch hot heating elements. Do not
use a towel or other bulky cloth instead of a potholder.
• Do not heat unopened food containers--Buildup of
pressure may cause container to burst and result in
injury.
* Remove the oven door from any unused range if it
isto be stored or discarded.
IM PORTANT--Do not attempt to operate the oven
during a power failure. If the power fails, always turn
the oven off. If the oven is not turned off and the power
resumes, the oven may begin to operate again. (Food left
unattended could catch fire or spoil.)
Electronic controllers can be damaged by
cold temperatures. When you use your appliance for
the first time, or if it has not been used for a long
period of time, make sure that it has been exposed to a
temperature above 0°C/32°F for at least 3 hours before
connecting it to the power supply.
IMPORTANT INSTRUCTIONS FOR USING YOUR
COOKTOP
• Know which knob controls each surface heating unit.
Use proper pan size. This appliance is equipped with one
or more surface units of different sizes. Select utensils
having flat bottoms large enough to cover the surface unit.
The use of undersized utensils will expose a portion of the
surface heating unit to direct contact and may result in
ignition of clothing. Proper relationship of utensil to the
surface unit will also improve efficiency.
Utensil handles should be turned inward and not
extend over adjacent surface units. To reduce the risk
of burns, ignition of flammable materials, and spillage due
to unintentional contact with the utensil.
Never leave surface burners unattended at high heat
settingsiBoilovers cause smoking and greasy accumula-
tions that may ignite, or a pan that has boiled dry may
melt.
Protective linersiDo not usealuminum foil to line oven
bottom or any other part of the appliance. Only use
aluminum foil as recommended for baking if used as a
cover placed on the food. Any other use of protective liners
or aluminum foil may result in a risk of electric shock or
fire or short circuit.
Glazed cooking utensilsiOnly certain types of glass,
glass/ceramic, ceramic, earthenware, or other glazed
utensils are suitable for rangetop servicewithout breaking
due to the sudden change in temperature. Check the
manufacturer's recommendations for cooktop use.
Do not use decorative surface element covers. Ifan
element isaccidentally turned on, the decorative cover will
become hot and possibly melt. Burns will occur if the hot
covers are touched. Damage may also be done to the
cooktop.
FOR GLASS COOKTOPS ONLY
• Do not clean or operate a broken cooktopilf cooktop
should break, cleaning solutions and spillovers may
penetrate the broken cooktop and create a risk of electric
shock. Contact a qualified technician immediately.
Clean cooktop glass with cautionilf a wet sponge or
cloth is used to wipe spills on a hot cooking area, be
careful to avoid a steam burn. Some cleaners can produce
harmful fumes if applied to a hot surface.
• Do not place hot cookware on cold cooktop glass.
This could cause glassto break.
IMPORTANT SAFETY INSTRUCTIONS
= Avoid scratching the cooktop glass with sharp
objects.
IMPORTANT INSTRUCTIONS FOR USING YOUR
OVEN
= Use care when opening oven door or warmer drawer
(if equipped)iStand to the side of the range when
opening the door of a hot oven. Let hot air or steam
escape before you remove or replace food in the oven /
warmer drawer.
Keep oven vent ducts unobstructed. The oven vent is
located at the rear of the cooktop on the right side.
Touching the surfaces in this area when the oven is
operating may cause severe burns. Also, do not place
plastic or heat-sensitive items on or near the oven vent.
These items could melt or ignite.
Placement of oven/warmer drawer (if equipped)
Racks. Always place oven racks in desired location while
oven/warmer drawer (if equipped) iscool. If rack must be
moved while oven is hot use extreme caution. Use
potholders and grasp the rack with both hands to reposi-
tion. Do not let potholders contact the hot heating
elements in the oven/warmer drawer (if equipped).
Removeall utensils from the rack before moving.
• Do not use the broiler pan without its insert. The
broiler pan and its insert allow dripping fat to drain and be
kept away from the high heat of the broiler.
• Do not cover the broiler insert with aluminum foil.
Exposed fat and grease could ignite.
Do not touch a hot light bulb with a damp cloth.
Doing so could cause the bulb to break. Disconnect the
appliance or turn off the power to the appliance before
removing and replacing light bulb.
IMPORTANT INSTRUCTIONS FOR CLEANING
YOUR RANGE
= Clean the range regularly to keep all parts free of
grease that could catch fire. Exhaust fan ventilation
hoods and grease filters should be kept clean. Do not
allow grease to accumulate on hood or filter. Greasy
deposits in the fan could catch fire. When you are flaming
food under the hood, turn the fan on. Refer to the hood
manufacturer's instructions for cleaning.
Kitchen cleaners and aerosols--Always follow the
manufacturer's recommended directions for use. Be
aware that excess residue from cleaners and aerosols may
ignite causing damage and injury.
SELF-CLEANING OVENS
= In the self-cleaning cycle, only clean the parts listed
in this Use and Care Guide. Before self-cleaning the
oven, remove the broiler pan and any utensils or foods
from the oven.
• Do not use oven cleanersiNo commercial oven
cleaner or oven liner protective coating of any kind should
be used in or around any part of the oven.
• Do not clean door gasketiThe door gasket isessential
for a good seal. Care should be taken not to rub, damage
or move the gasket.
• Remove oven racks. Oven racks color will change if left
in the oven during a self-cleaning cycle.
The health of some birds is extremely
sensitive to the fumes given off during the self-
cleaning cycle of any range. Move birds to another
well ventilated room.
IMPORTANT SAFETY NOTICE
The California Safe Drinking Water and Toxic Enforcement Act requires the Governor of California to publish a list of substances
known to the state to cause cancer, birth defects or other reproductive harm, and requires businesses to warn customers of potential
exposure to such substances.
SAVE THESE SAFETY INSTRUCTIONS
Z
O
Z
Selecting Surface Cooking Utensils
Forbest result and energy conservation, choose cooking utensils that havethese characteristics:
Pans should have flat bottoms that make
good contact with the entire surface ele-
ment. Check for flatness by rotating a ruler
across the bottom. There should be no
gaps between the pan and ruler.
Note: Always use a utensil for its intended
purpose. Follow manufacturer's instruc-
tions. Some utensils were not made to be
used in the oven or on the cooktop.
*GOOD
w
u
t t
• Flat bottom and straight sides.
• Tight fitting lids.
• Weight of handle does not tilt pan. Pan
is well balanced.
• Pan sizes match the amount of food to
be prepared and the size of the surface
element.
• Made of material that conducts heat
well.
• Easyto clean.
* Specialty pans such as lobster pots, griddles
and pressure cookers may be used but must
conform to the above recommended cook-
ware requirements.
POOR
• Curved and warped pan bottoms.
• Pan overhangs unit by more than 2.5
cm(1 ").
• Heavy handle tilts pan.
• Pan is smaller or larger than element.
Specialty Pans & Trivets
Woks with flat bottoms suitable for
use on your cooktop are available in
most cookshop or hardware stores.
DO NOT use two
elements (if the cooktop is not
equipped with bridge element) to heat
one large pan such as a roaster or
griddle, or allow cooking utensils to
boil dry. The bottom surface of the
pan in either of these situations could
cause discoloring or crazing of the
range surface.
DO NOT use a wok if it is equipped
with a metal ring. Because this ring
traps heat, the surface element and
cooktop surface could be damaged.
Wire trivets: Do not use wire trivets.
Cookware bottoms must be in direct
contact with the surface elements.
For glass smoothtop models, only
flat bottomed woks (without
support rings) may be used.
1. Usetested recipes and follow instructions carefully. Check with the
manufacturer of glassjars for the latest canning information.
2. Useflat-bottomed canners only. Heat is spread more evenly when the
bottom surface is flat.
3. Center canner on the surface element.
4. Start with hot water and a high heat setting to reduce the time it takes to
bring the water to a boil; then reduce the heat setting as low as possible to
maintain a constant boil.
5. It isbest to can small amounts and light loads.
Prevent damage to cooktop:
1. Do not usewater bath or pressure canners that extend more than one inch
beyond the edge of the surface element.
2. Do not leave water bath or pressure canners on high heat for an extended
amount of time.
3. Alternate surface elements between each batch to allow the units and
surrounding surfaces to cool down. Tryto avoid canning on the same
element all day.
Safecanning requires that harmful micro-organisms are
destroyed and the jars are sealed completely. When canning in awater bath
canner, a gentle but steady boil must be maintained continuously for the
required time.
Canning Tips &
Information
Canning can generate
large amounts of steam. Useextreme
caution to prevent burns. Always raise
the lid to vent steam away from you.
(-;,
Z
O
Z
Range features
Electronic Oven Controls
with Clock and Kitchen Timer
Surface Burner
Control Knob
Broil Element
Oven
g
Oven
adjustable
Oven Racks
One Piece
Door Handle
Glass Front Oven
Door with Large
Window Opening
Insert
Broil Pan
Standard Ribbon
Element
Standard Ribbon
Element
Standard Ribbon
Element
Expandable
Element
Hot Surface
Indicator Lights
Ceramic Glass
Cooktop
Note: Theappearanceofyourovencontrolmaydifferslightlyfromtheoneillustratedbelow.
However,allfunctionsarethesame.Also,pushbuttonsorpadsmaybeshaped
differentlythanthoseappearinginthisUseandCareGuide.
Control Pad
Functions
READTHE INSTRUCTIONS CAREFULLYBEFOREUSING THE OVEN. Forsatisfactory use of
your oven, become familiar with the various functions of the oven asdescribed below.
OFF CANCEL PADi Used to clear
any function previously entered
except the time of day and minute
timer. Push OFFCANCEL to stop
cooking. \
BAKE PADi •
Usedto
enter the normal
baking mode
temperature.
BROILi Used
to select the o
variable broil_
function.
CLEAN PADi
Used to select
UP and DOWN ARROWS PADS i Used along with
the function pads to select oven temperature,
cooking time, stop time (when programming an
automatic stop time), time of day, clean time and
minute timer.
thecycle,self-cleaning /
OVEN, PREHEAT & LOCK LIGHTSi The "OVEN" light will glow each
time the oven unit turns on to maintain the set oven temperature. The
"PREHEAT" light will glow when the oven isfirst set to operate, or if the
desired temperature isreset higher than the actual oven temperature.
The "LOCK" light will flash until the door locks when the self-clean
cycle is in use. It glows constantly after the door locks.
_ OVEN
_l PREHEAT
CLEAN
DOOR LOCKED .....................................................
/
CLOCK PADi
Used to set the
time of day.
/ /
C sOCcoo
o@o
STOP
TIMER PAD i Used to set
or cancel the minute timer.
The minute timer does not
start or stop cooking.
FEATURE
INDICATOR
LIGHTSiThese
light to show
which feature is
in use.
BAKETIME
PAD i Used
to enter the
length of the
baking time
(if equipped).
STOPTIME
PAD i Used _<_°_
Z
to set the _2_
desired stop _....
time for _
baking. Can :ZC:
be used with
BAKE TIME to
program a
delayed bake
cycle (if
equipped).
The oven can be programmed to: BAKE normally, TIME BAKE, BROIL, SELF-CLEAN
Note: The oven function will not work if the time of day clock is not set.
For a silent control panel:
When choosing a function, a beep will be heard each time a pad is pushed. If desired, the controls can be programmed for
silent operation. Pushand hold STOP TIME pad T,M_.After 7 seconds, the control will beep once. This will block the controls
from sounding when a pad is pushed. To return the sound, push and hold STOP TIME pad aga n for 7 seconds until 1
beep is heard.
The electronic oven control isset to operate in °F(Fahrenheit) when shipped from the factory. Temperature
The oven can be programmed for any temperature from 170°F to 550°F (65°C to 287°C).
To change the temperature to °C (celsius) or from °C to °F (control should not be in a
Bake or Clean mode):
1. Push BROIL pad "-- appears in the display.
2. Push and hold the UP ARROW A pad until "HI" appears in the display.
3. Push and hold BROIL pad until °F or °C appears in the display.
4. Push UP A or DOWN ARROW V pad to change °F to °C or °C to °F.
5. Pushany function pad to return to normal operating mode.
Conversion
(Fahrenheit / Celsius)
Setting the
Clock
FEATURE OVERVIEW
• To Set the Clock
• To Set the Minute Timer
NOTE: The oven function
will not work if the time of
day clock is not set.
O
O
_3SEC
OFF
i!! _ iii
CANCEL
o 91D OVEN
PREHEAT
CLEAN
.............................................._ DOOR LOCKED
Note: The oven function will not work if the time of day clock is not set.
To Set the Clock
When the range isfirst plugged in, or when the power supply to the appliance has been interrupted, the display will flash
"12:00"•
1 Push CLOCK SET pad _oc_
• SET "
2. Within 5 seconds, push and hold the UP A or DOWN ARROW pad v until the correct time of day appears in the
display.
Note: The clock cannot be changed during any timed bake or self-clean cycle.
To Set the Minute Timer
1. PushTIMER ON/OFF pad _.
2. Push the UP ARROW pad A to increase the time in one minute increments. Push and hold the UP ARROW pad/_ to
increase the time in 10 minute increments. The timer can be set for any amount of time from 1 minute to 11 hours and
59 minutes.
Note: If you push the DOWN ARROW pad v first, the timer will advance to 11 hours and 59 minutes.
3. The display shows the timer count down in minutes until one minute remains• The display will count down in seconds•
4. When the set time has run out, the timer will beep 3 times• It will continue to beep 3 times every 60 seconds until the
TIMER ON/OFF pad ispushed•
Note: The minute timer does not start or stop cooking• It servesasan extra timer in the kitchen that will beep when the set
time has run out. The minute timer can be used alone or during any of the other oven functions• When the minute timer is in
usewith any other mode, the minute timer will be shown in the display• To view other functions, push the function pad for that
mode.
To Change the Minute Timer while it is in use:
While the timer isactive and shows in the display, push and hold the UP A or DOWN ARROW pad v to increase or
decrease the time.
To Cancel the Minute Timer before the set time has run out :
Push TIMER ON/OFF pad
10
Setting Surface Controls
1. Placethe pan on the surface element.
2. Push in and turn the surface element control knob to desired setting.
3. The surface signal light will glow when one or more elements are turned on. Always turn
the element off before removing the pan.
Note: The size and type of utensil used, and the amount and type of food being
cooked will influence the setting needed for best cooking results.
Setting Type of Cooking
MAX (HI) Start most foods, bring water to a boil, pan broiling.
MED (5) Maintain a slow boil, thicken sauces and gravies, steam vegetables.
MED-LOW (2-4) Keepfood cooking, poach, stew.
MIN (1-SIM) Keep warm, melt, simmer.
*The suggested settings found in the chart above are based on cooking in medium thickness
aluminum pans with lids. Settings may vary when using other types of pans.
Do not place items such as salt and pepper shakers, spoon holders or
plastic wrappings on top of the cooktop when it is in use. These items could melt or
ignite. Potholders, towels or wood could catch fire if placed too close to the element.
Ceramic-Glass Cooktop
The ceramic-glass cooktop has electric heating coils located below the ceramic-glass surface.
The design of the glass cooktop outlines the area of the surface heating coils below. Most
importantly, make sure the diameter of the pan matches the diameter of the surface area.
Heat is transferred up through the surface of the cooktop. Only flat-bottomed pans should be
used. The type and size of cookware, number of surface units in use and the settings of the
surface units are factors that will affect the amount of the heat that will spread to areas
surrounding the units. The areas surrounding the units may become hot enough to cause burns.
The cooktop should not be used as a cutting board or work surface. Dropping heavy or hard
objects on the cooktop may crack it. Panswith rough bottoms may scratch the cooktop surface.
Placing foods not in utensils directly on the smoothtop surface isnot recommended as difficult
cleaning will result and foods may smoke and cause a potential fire hazard. Never use griddle
or similar cooking sheet on the ceramic-glass cooktop.
Surface
Cooking
FEATURE OVERVIEW
• Setting Surface Controls
• Ceramic-Glass Cooktop
NOTE: Due to the high
intensity of heat generated
by the surface elements,
the glass surface will turn
green when the element is
turned off. This phenom-
enon isnormal and the
glass will come back to its
original white color after it
hascompletely cooled
down. (White glass
cooktops only).
Z
O
Z
Types of Heating Units Used
REGULARRADIANT HEATING UNITS (some models)
The ceramic-glass design shows the location of the heating surfaces.
Control knobs are used to set the heat power levels. Knobs need first to be pressed in when at
OFFposition, then turned to the desired heat settings.
A glowing red surface extending beyond the bottom edge of the cooking utensil indicates the
utensil is too small for the unit.
The control knob does not have to be set exactly on a particular mark. Use the marks asa
guide and adjust the control knob as needed. The hot surface and surface indicator lights will
glow.
Note: A built-in protector will automatically turn off the radiant heating unit if the ceramic-glass
temperature exceeds the set limit.
11
Surface
Cooking
FEATURE OVERVIEW
• Ceramic-Glass Cooktop
Expandable Radiant Element
Control Dial
EXPANDABLE RADIANT HEATING UNITS (some models)
This heating unit adapts to both small and large heating utensils. The unit control dial has a
dual set of graduations. For small utensils use the left side of the control dial; for large utensils
the right. Only the inner surface of the unit heats when using it for small utensils; the whole
surface heats for large utensils. The hot surface and surface indicator lights will glow when the
heating unit isturned ON.
Note: During any heat setting of the outer radiant element, the inner radiant element cycles on
and off with the outer element.
Indicator Lights
Two different surface control lights will glow on your range: Surface Indicator Lights and Hot
Surface Indicator Lights.
• The surface indicator lights, located on the control panel, glow when any surface unit
isturned on. A quick glance at the lights after cooking isan easy check to be sure all
surface controls are turned off.
• The hot surface indicators lights, located under the glass cooktop, will come on as the
surface cooking area heats up and will continue to glow until the glass cooktop has cooled
down to a moderate level. The lights may remain on even though the controls are turned to
OFE
Oven Vent(s)
and Racks
Oven Vent
Oven Vent(s) and Racks
Oven Vent Location
The oven isvented at the rear of the cooktop. When the oven is on, warm air is released
through the vent(s). This venting is necessary for proper air circulation inthe oven and good
baking results. DO NOT block the vent(s). Doing so may cause cooking failures, fire or damage
to the appliance.
Arranging Oven Racks
ALWAYS ARRANGE OVEN RACKS WHEN THEOVEN ISCOOL (PRIORTO OPERATINGTHE
OVEN). Always use oven mitts when using the oven.
To remove an oven rack, pull the rack forward until it stops. Lift up front of rack and slide out.
To replace an oven rack, fit the rack onto the guides on the oven walls. Tilt the front of the
rack upward and slide the rack back into place.
Changing Oven
Light
Be sure the oven is unplugged and all parts are COOL before replacing the oven
light bulb. Do not turn the oven light on during a self-cleaning cycle. High temperature will
reduce lamp life.
On some models an interior oven light will turn on automatically when the oven is opened.
The oven light may be turned on when the door is closed by using the oven light switch located
on the Electronic Oven control.
On a self-cleanning oven the lamp is covered with a glass shield held in place by a wire holder.
THISGLASS SHIELD MUST ALWAYS BE IN PLACEWHEN THE OVEN ISIN USE.
To Replacethe Light Bulb:
BE SUREOVEN IS COOL
1. Turn the power off at the main source.
2. Wear a leather-faced glove for protection against possible broken glass.
3. Replace bulb with a 40 Watt appliance bulb only.
4. Forself-cleaning oven, presswire holder to one side to release glass shield, change bulb and
be sure to replace glass shield.
12
O 83SEC O O
• ii{..........................................il
O O _ O
o o OVEN
ID PREHEAT
::CLEAN
................................................._ DOOR LOCKED
Setting Oven
Controls
Feature
Overview
* To Set or Change
Temperature for Normal
Baking
NOTE: The oven function
will not work if the time of
day clock is not set.
Note: The oven function will not work if the time of day clock is not set.
To Set or Change the Temperature for Normal Baking
The oven can be programmed to bake at any temperature from 170°F to 550°F (65°C to 287°C).
Note: The oven control hasa built-in safety feature that will shut off the
oven if the control is left on for more than 11 hours 59 minutes•
To Set the Controls for Normal Baking:
1 Push BAKE pad ,,i i i II appears in the display•
2. Within 5 seconds, push the UP A or DOWN ARROW pad v. The display will show "350°F (177°C)." Byholding the
UP/_ or DOWN ARROW pad v, the temperature can then be adjusted in 5°F (1°C) increments•
3. As soon as the UP/_ or DOWN ARROW pad v is released, the oven will begin heating to the selected temperature•
When the displayed temperature reaches the desired baking temperature, the control will beep 3 times•
4. To cancel the baking function, push the CANCELOFF pad _°_L_.
To Change the Oven Temperature after Baking has Started:
1. If you are using the minute timer, push the BAKE pad and make sure the bake temperature is displayed•
2. Pushthe UP A or DOWN ARROW pad v to increase or decrease the set temperature•
To Set Control for Continuous Bake or 12 Hour Energy Saving:
The oven control hasa built-in 12 Hour Energy Saving feature that will shut off the oven if the control isleft on for more than
11 hours and 59 minutes. The oven can be programmed to override this feature for continuous baking.
To set control for continuous baking:
1. PushTIMER ON/OFF pad _, "0:00" will appear in the display•
2. Pushand hold TIMER ON/OFF pad _ down for 5 seconds until tone is heard, ,,ii hr" will appear in display for
continuous cooking• The current time of day will return to the display•
3. To cancel the Continuous Bake Function, push TIMER ON/OFF pad _ and hold for 5 seconds until tone isheard•
"12hr" will appear in display indicating that the control has returned tothe 12 Hour Energy Saving feature•
To Set Control for Oven Lockout:
The control can be programmed to lock the oven door and inactivate the oven controls.
To Set Control for Oven Lockout feature:
1 Pushthe CANCEL OFF pad ......• _A_ELand hold for 3 seconds• Loc will appear in display, the "Door Locked indicator light
will flash and the motor driven door lock will begin to close automatically• DO NOT open oven door while the indicator
light isflashing• Allow about 15 seconds for the oven door to lock. Once the oven door islocked, the current time of day
will appear in the display•
2. To cancel the lockout feature, push CANCEL OFF pad and hold for 3 seconds• The control will unlock the oven door
and resume normal operation•
Note: If any control pad is pressed while the Oven Door/Control Lockout mode, "Loc" will appear in the display
until the control pad is released.
13
Z
O
Z
Setting Oven
Controls
FEATURE OVERVIEW
• Timed Bake Feature
O
O
_3SEC
OFF
i!! _ iii
CANCEL
o o OVEN
PREHEAT
CLEAN
.............................................._ DOOR LOCKED
O O
; CLOCK :
iA SET
STOP
TIME
To Set the Automatic Timer (Timed Bake Feature-if equipped)
The COOK TIME and STOP TIME controls operate the Timed Bake Feature. The automatic timer will turn the oven on and off
at the times you select in advance.The oven can be programmed to start immediately and shut off automatically or to begin
baking at a later time with an automatic shutoff.
To Program the Oven to Begin Baking Immediately and To Shut Off Automatically:
1. Besure that the clock shows the correct time of day.
2. Placethe food in the oven.
3. Pushthe BAKE pad
4. Within 5 seconds, push the UP A or DOWN ARROW pad v. The display will show "350°F (177°C)." Byholding the UP
or DOWN ARROW pad v, the temperature can then be adjusted in 5°F (1°C) increments.
5. Pushthe COOK TIME pad co_ ,,0:00,, will flash in the display.
6. Pushthe UP _ or DOWN ARROW pad v until the desired amount of baking time appears in the display.
To Program Oven for a Delayed Start Time and to Shut-Off Automatically:
1. Besure that the clock shows the correct time of day.
2. Placethe food in the oven.
3. Pushthe BAKE pad
4. Within 5 seconds, push the UP or DOWN ARROW pad v. The display will show "350% (177°C)." Byholding the UP
or DOWN ARROW pad v, the temperature can then be adjusted in 5% (1°C) increments.
5. Pushthe COOK TIME pad _oo_,,0:00,, will flash in the display.
T!_E.
6. Pushthe UP _ or DOWN ARROW pad v until the desired amount of baking time appears.
7. Pushthe STOP TIME pad The earliest possible stop time will flash in the display.
8. Pushthe UP _ or DOWN ARROW pad v until the desired stop time appears in the display.
9. Once the controls are set, the control calculates the time when baking will start in order to finish at the time you have set.
Once the Controls are Set:
1. The oven will come on and begin heating to the selected baking temperature.
2. The oven temperature (or time of day) will show in the display.
When the Set Cook Time Runs Out:
1. "END" will appear in the display window and the oven will shut off automatically.
2. The control will beep 3 times every 60 seconds until the CANCEL OFF pad o_,i is pushed.
To Change the Oven Temperature or Cook Time after Baking has Started:
1. Pushthe function pad you want to change.
2. Pushthe UP A or DOWN ARROW pad v to adjust the setting.
Use caution when using the automatic timer. Use the automatic timer when cooking cured or frozen meats
and most fruits and vegetables. Foods that can easily spoil such as milk, eggs, fish, meat or poultry, should be chilled in the
refrigerator first. Evenwhen chilled, they should not stand in the oven for more than 1 hour before cooking begins, and should
be removed promptly when cooking iscompleted.
14
Oven Baking Informations
For best results, preheat the oven before baking cookies, breads, cakes, pies or pastries, etc.
There is no need to preheat the oven for roasting meat or baking casseroles.
The cooking times and temperatures needed to bake a product may vary slightly from your
previously owned appliance. Refer to "Recalibrating Your Oven Temperature" section.
Baking problems and solutions
Baking Problems Causes Corrections
Cookiesand
biscuits burn on
the bottom.
Cakes too dark on
top or bottom.
Cakes not done in
the center.
Cakes not level.
Foods not done
when cooking
time is up.
Cookies and biscuits put into
the oven before the pre-heating
time is completed.
Oven rack overcrowded.
• Dark pan absorbs heat too fast.
• Cakes put into the oven before
preheating time is completed.
• Oven rack position too high or
low.
• Oven too hot.
• Oven too hot.
• Incorrect pan size.
• Pan not centered in the oven.
• Range not level.
• Pan too close to oven wall or
rack overcrowded.
• Pan warped.
• Oven too cool.
• Oven overcrowded.
• Oven door opened too
frequently.
Setting Oven
Controls
FEATURE OVERVIEW
• Oven Baking
Informations
• Air Circulation in the
Oven
• Allow oven to preheat to the selected temperature
before placing food in oven.
• Choose pan sizes that will permit 2" to 4" (5.1 cm to
10.2 cm) of air space on all sides when placed in the
oven.
• Use a medium-weight aluminum baking sheet.
• Allow oven to preheat to the selected temperature
before placing food in the oven.
• Use proper rack position for baking needs.
• Set oven temperature 25°F/12°C lower than
recommended.
• Set oven temperature 25°F/12°C lower than
recommended.
• Use pan size suggested in recipe.
• Use proper rack position and place pan so there is 2"
to 4" (5.1 cm to 10.2 cm) of space on all sides of pan.
• Place marked glass measuring cup filled with water
on the center of the oven rack. If water level is
uneven, refer to the installation instructions for
leveling the appliance.
• Be sure to allow 2 " to4" (5.1 cmto 10.2 cm)of
clearance on all sides of each pan in the oven.
• Do not use pans that are dented or warped.
• Set oven temperature 25°F/12°C higher than
suggested and bake for the recommended time.
• Be sure to remove all pans from the oven except the
ones to be used for baking.
• Open oven door only after shortest recommended
baking time.
Z
O
Z
Air Circulation in the Oven
If using multiple pans, stagger as shown. If using one pan, place in center of oven.
Forbest air circulation and baking results, center pans as much as possible. Allow 2-4" (5-10
cm) around the utensil(s) for proper air circulation and be sure pans do not touch each other,
the door, sides or back of oven. The hot air must circulate around the pans in the oven for
even heat to reach all parts of the oven.
15
Setting Oven
Controls
FEATURE OVERVIEW
• Broil
O
O
_3SEC
OFF
i!! _ iii
CANCEL
o o OVEN
PREHEAT
CLEAN
.............................................._ DOOR LOCKED
O O
; CLOCK :
iA SET
STOP
TIME
BROIL
Broiling isa method of cooking tender cuts of meat by direct heat under the broil element of the
oven. A beep lets you know when the broil temperature is reached• Be sure you center the broiler
pan directly under the broil element for best results•
Arrange oven rack while oven isstill cool. Position the rack as needed•
The broiler pan and its insert allow dripping grease to drain and be kept away from the high heat of
the broiler. DO NOT usethe pan without its insert. DO NOT cover the insert with foil. The
exposed grease could ignite.
Should an oven fire occur, close the oven door and turn off the oven. If the fire continues, throw baking soda
on the fire or use a fire extinguisher. DO NOT put water or flour on the fire. Flour may be explosive and water can cause a
grease fire to spread and cause personal injury.
To set the oven to broil
1. Arrange oven rack while oven is still cool.
2. Push the BROIL pad
3. Push and hold the UP A or DOWN ARROW pad v until the desired broil setting levelappears in the display• Push UP
ARROW pad/x for HI broil or the DOWN ARROW pad v for LO broil• Most foods can be broiled at the HI broil setting•
Select the LO broil setting to avoid excessbrowning or drying of foods that should be cooked to the well-done stage•
4. Placegrid on the broiler pan, then place the food on the grid. DO NOT use the pan without its grid. DO NOT cover the grid
with foil. The exposed grease could ignite•
5. Placethe pan on the oven rack. Open the oven door to the broil stop position when broiling.
6. Broil on one side until food is browned; turn and cook on the second side. Note: Always pull the rack out to stop position
before turning or removing food.
7. When broiling isfinished, push the CANCEL OFF pad i%1.
16
Loading...