Kenmore 79045403410, 79045403411, 79045409410, 79045409411 Installation Guide

iNSTALLATiON AND SERVICE MUST BE PERFORMED BY A QUALiFiED iNSTALLER.._

iMPORTANT: SAVE FOR LOCAL ELECTRICAL iNSPECTOR'S USE.

READ AND SAVE THESE iNSTRUCTiONS FOR FUTURE REFERENCE. C US

FOR YOUR SAFETY: Do nat stare or use gasallne or other flammable vapars

and liquids in the vicinity of this or any other appliance. LISTED

iMPORTANT iNSTALLATiON
iNFORMATiON

* All electric cooktops run off a

single phase, three-wire or four-wire
cable, 240/208 volt, 60 hertz, AC

only electrical supply with ground.

* Please note minimum distance

between cooktop and adjacent and
overhead unprotected cabinetry is

30" (76.2 cm).

The corners

of this unit are fragile.
Carefully install the cooktop
by its sides. When installing,
never let the weight of the
unit rest on any one corner.

30" (76.2 cm) min. for unprotected cabinet.

24" (6t cm) min. for protected surface.

_....... .,.4

Cooktop Dimensions

30" Min. _

(76.2 cm)

4" X 8"
(10.2 cmx 20.3

cm) opening at the
right rear to route

Cooktop Cutout Dimensions

Figure |

30" Ceramic Model 293¼(75.6) 30 1/8 (76.5) 20 3/8 (51.8) 2034 (52.7) 6 (15.2)

All dimensions ore in inches (cm).

Allow 2" (5 cm) space below cooktop to clear the electric cable and allow for
installation of the junction box on the wall at the back of the cooktop.

Printed in China

P/N 318205431 (1311) Rev. A

English - pages 1-8

EspaSol - pages 9-16

Fran_:ais - pages 17-24

Overhead Cabinet Should Not Exceed
a Maximl,m Depth of 13" (33 cm)

30" (76.2 cm) Min.
Clearance Between

the Top of the Cooking

Platform and the Bottom

of an Unprotected
Wood or Metal Cabinet.

24" (61 cm) Min. when

Bottom of Wood

or Metal Cabinet is

Protected by Not
Less Than 1/8" Flame

Retardant Millboard
Covered With Not Less
Than No. 28 MGS Sheet

Steel, 0.015" (0.4 ram)
Stainless Steel, 0.024';

(0.6 ram) Aluminum or

0.020'; (0.5 ram) Copper

21/2'' (6.4 cm) Min. From Edge of
Cutout to Front Edge of Countertop

18"

(45.7 cm)

G

Min.

Res_ nmcmeBedtewdeen
Rear Edge of

Cutout and Nearest
Combustible Surface 25.4 cm)

Above Countertop

10"'

F

Approximate Location

of Junction Box

I

12 ml

(30.5 cm)

71/2'' (19.1 cm)
Min. From Edge
of Cooktop

to Nearest
Combustible

Wall (Either
Side of Unit).

It is not recommended to use
drawer underneath cooktop.

Empty space is needed for
installation purpose.

Letters on this figure refer to chart on front page except for I.

To eliminate the risk of burns or fire by

reaching over heated surfaces, cabinet storage space
located above the cooktop should be avoided. If cabinet
storage is provided, risk can be reduced by installing a
range hood that projects horizontally a minimum of 5"
(12.7 cm) beyond the bottom of the cabinets.

Figure 2 - COUNTERTOP CUTOUT OPENING

2

• 30"' Model _ 30"' (76.2 cm)
36" Model 36" (91.4 cm)

important Notes to the installer

1. Read all instructions contained in these installation
instructions before installing the cooktop.

2. Remove all packing material before connecting the
electrical supply to the cooktop.

3. Observe all governing codes and ordinances.

4. Be sure to leave these instructions with the consumer.

Importanf Note to fhe Consumer

Keep these instructions with your Use and Care Guide for

future reference.

iMPORTANT SAFETY

INSTRUCTIONS

° Be sure your cooktop is installed and grounded

properly by a qualified installer or service
technician.

° These cooktops must be electrically grounded in

accordance with local codes or, in their absence,
with the National Electrical Code ANSI/NFPA No.

70mlatest edition in the United States, or with CSA

Standard C22.1, Canadian Electrlcal Code, Part 1, in
Canada.

The electrlcal power to the cooktop must

be shut off while llne connections are being made.
Failure to do so could result in serious injury or death.

An extension cord must not be used with

this appliance. Such use may result in a fire, electrlcal
shock, or other personal injury.

2. The appliance should be connected to the fused
disconnect (or circuit breaker) box through flexible

armored or nonmetallic sheathed cable. The flexible
armored cable extending from this appliance should

be connected directly to the grounded junction box.
The junction box should be located as shown in

Figure 2 with as much slack as possible remaining in
the cable between the box and the appliance, so it
can be moved if servicing is ever necessary.

3. A suitable strain relief must be provided to attach
the flexible armored cable to the junction box.

Observe all governing codes and local ordinances.

Unpacking Instructions

1. Leave corner supports on cooktop until completion
of Electrical Connection.

2. Be sure the bottle of cleaner conditioner packed in
the literature bag is left where the user can find
it easily. It is important that the ceramic-glass

smoothtop be pretreated before use. See Ceramic

Glass Cooktop Cleaning and Maintenance section
in the Use and Care Guide.

Provide Electrlcal Connection

Install the junction box under the cabinet and run
120/240 or 120/208 Volt, AC wire from the main

circuit panel. NOTE: DO NOT connect the wire to the
circuit panel at this time. Wait until all wires have been
connected in the junction box.

Electrlcal Requirements
Observe all governing codes and local ordinances.

1. A 3-wire or 4-wire single phase 120/240 or 120/208
Volt, 60 Hz AC only electrical supply is required

on a separate circuit fused on both sides of the
line (a 40A time-delay fuse or circuit breaker is
recommended). DO NOT fuse neutral.

NOTE: Wire sizes and connections must conform with
the fuse size and rating of the appliance in accordance

with the National Electrical Code ANSIiNFPA No. 70-
latest edition, or with CSA standard C22.1, Canadian
Electrical Code, Part 1, and local local codes and

ordinances.

v and Serial Plate

(Under Cooktop)

Figure 3

3