Kenmore 758144107 Owner’s Manual
f
READ AND
SAVE THESE
mNSTRUCTmONS
SF_AIRS
OWner'S
Stock No.
42°14410
Mode_ No.
758.144107
QUIETCOMFORT
WHOLE HOUSE
HUMIDmFIER
FOR YOUR
READ
ALL mNSTRUCTIONS
CAREFULLY
Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.
Part No. SP6557 Printedin Canada
10 Ga_on Output
• Operating mnstructions
• Parts List
_#" FULL ONE YEAR WARRANTY ON HUIVImDtFmER "_
[f within one (1) year from the date of purchase, th{e humidifier fairs due to a defect in
material or workmanship, Sears will repair it, free of charge. If within two (2) years from
the date of purchase, the motor fails due to defect in materia_ or workmanship, Sears
will repair it free of charge.
This warranty service is available by simply returning the humidifier to the nearest Sears
Store, and it wilt be repaired or replaced, at Sears option, free of charge.
Th{s warranty applies onmy while this product is used in the United States.
This warranty gives you spec{fic _ega_rights, and you may also have other rights which
GENERAL SAFETY
Safety Signal Words 5.
DANGER: means if the safety information is
not followed, someone will be seriously 6.
injured or killed.
WARNING: means if the safety information is
not followed, someone could be seriously 7.
injured or killed.
CAUTION: means if the safety information is 8.
not followed, someone may be seriously
injured or killed.
1. To reduce the risk of fire or shock hazard, plug 9.
humidifier directly into a 120V, A.C. electrical
outlet. Do not use extension cords.
2. Keep the electric cord out of traffic areas. To
reduce the risk of fire hazard, never put the
electric cord under rugs, near heat regis-
ters, radiators, stoves or heaters.
3. Always unplug the humidifier before mov-
ing it, before cleaning, or whenever the
humidifier is not in service.
4. Keep the humidifier clean.
Table of Contents
Warranty Information .................................. 2
General Safety instructions ........................ 2
To Save A Service Call ............................... 2
Know Your Humidifier ................................. 3
Humidifier Operations ................................ 4
Assembly .................................................... 4
Location instructions .................................. 5
Electrical Hook-Up ...................................... 5
iNSTRUCTiONS
Do not put foreign objects inside the
humidifier.
Do not allow to be used as a toy. Close
attention is necessary when used by or
near children.
Never use your humidifier while any part
is missing or damaged in any manner.
To reduce the risk of electrical hazard or
damage to humidifier, do not tilt, jolt or tip
humidifier while unit is running.
To reduce the risk of damage to humidifier,
unplug humidifier, when the base is empty
or when the humidifier is not in use.
10.To reduce the risk of accidental electrical
shock, do not touch the cord or controls
with wet hands.
11.Note the warning label shown below.
tric shock, or injury always unplug
WARNING: To reduce risk of fire, elec-
before filling, servicing or cleaning.
Water Fill .................................................. 6-7
Operating Humidifier Controls ................... 7
Using Your Humidifier ................................. 8
Operating Tips for Best Performance ......... 8
Replacement and Care of Filters ........... 9-10
Cleaning Your Humidifier ..................... 11-12
Troubleshooting ....................................... ! 3
Repair Parts ......................................... 14o15
To Save a Service Call
Check the following if your humidifier is 3. is airflow control in operating position?
not operating. 4. is humidity control set high enough?
1. Is power cord attached to outlet? 5. Is the humdifier sitting on a level sur-
2. Is there electrical power to outlet? face?
2
Know Your Humidifier
Bottle HandRe
Humidity ControB
Description
Gallon Output/24 hrs
Capacity of Bottle
Capacity of Base
Sq. Ft. Coverage
Fan Speeds
Replacement Filter
Power Light
Fill Light
Auto Humidistat
Auto Shut Off
Controls
CUL Listed
Volts
Hertz
Amps
Watts
_ Speed Control
Bottle
BQse
"_ Filter:
Replacement No,
42=14906
42=14410
10
1,9 Gallons
2,0 Gallons
2100
3
42=14906
Yes
Yes
Yes
Yes
Rotary
Yes
120 A,C,
6O
0,80
8O
Based on an area with average insulation
and an 8 foot ceiling height.
Humidifier Operation
Your new Sears humidifier is designed to
satisfy home humidity requirements
through the principle of evaporation of
water into the air.
After water is added to the humidifier, the
filter begins to soak up the water and will
become saturated in approximately 30
minutes. Air drawn in through the open-
ings in the lower housing passes through
the filter by means of a circulation fan. As
air passes through the filter, moisture is
absorbed into the air and then released
in the form of vapor. No water droplets
will enter the home. All evaporation into
the air takes place in the humidifier,
which means that the residue left by
evaporating water is not passed into the
home, but remains in the filter_
This natural process of evaporation helps
eliminate the chance of white dust in the
humidified output air.
CAUTmON: Use only 42°14900 EPA
Registered Bacteriostat available
from SEARS Retail store. Under no
circumstances should you use water
treatment products designed for
Roto belt or Ultrasonic humidifiers.
Humidified air is
then reBeased
through the top
Dry air
enters
through the
louvers in
the housing
CAUTION: To reduce the risk of
injury, fire or damage to humidifier,
use only cleaners specifically recom-
mended for humidifiers. Never use
flammable, combustible or poisonous
materials to clean your humidifier. To
reduce the risk of scalds and damage
to humidifier, never put hot water in
humidifier.
Assembly
Carefully remove the humidifier and a!l
other contents from the carton.
There is a black strip that contains six
pads for the bottom of the humidifier.
Remove each pad and place one on
each of the six legs on the bottom of the
base as shown, by the solid dots.
Once installed return the humidifier to
it's original state and proceed to
'Location Instructions".
3
4
5
Location instructions --
WARNBNG: For your own safety, do
not use humidifier if any parts are
damaged or missing.
Step 1
Place humidifier on a flat level surface in
an area of house where most humidity is
needed, or one which would likely result
in moist air being circulated throughout the
house such as near a cold air return.
Placing the unit level is very' important.
Special attention should be given to
unit's level if the humidifier is located on
carpeting.
Moist air (humidity) produced will disperse
into the whole house, but the area closest
to the unit wil! have the highest humidity. If
the unit is positioned close to a window,
condensation may form on the window
pane. If this is not appropriate the unit
should be repositioned in another location.
NOTE: Due to release of coo!, moist air
from humidifier, it is best to direct air away
from home thermostat and hot air
registers. It is best to position humidifier
next to an inside wall. Hot air registers and
cold air from outside walls can affect the
efficiencies of the controls. Unit should not
be placed where warm air from a hot air
register blows directly on unit.
The humidifier should be positioned with
Step 2
the back (cord exit side) and left side, at
least 2 inches away from the wall. Air
needs to enter through all of the louvers in
the housing assembly in order for the
humidifier to operate at peak efficiency.
At least 2"
from wall
Electrical Hook-Up
Locate nearest 120V A.C. wal! socket in
the location desired, preferably on inside
wal!. With the humidifier in the desired
location, route the electrical cord safely
so no one will trip or upset the humidifier.
Plug in the electrical cord.
WARNmNG: To reduce the risk of fire
or shock hazard, humidifier should
be plugged directJy into a 120V A.C.
outlet. Do not use extension cords.
To reduce the risk of electrical shock,
this humidifier has a polarized plug (one
blade is wider than the other). This plug
wil! fit in a polarized outlet only one way. if
the plug does not fit fully in the outlet,
reverse plug. If it still does not fit, contact
a qualified electrician to install the proper
outlet. Do not change the plug in any way.
1
Water Fill
WARNING: To reduce the risk of
shock, always unplug humidifier
before cleaning or servicing,
WARNING: To reduce the risk of fire
or shock hazard, do not pour or spill
water into control or motor area.
mfcontroms get wet, let them dry como
p[ete[y and have unit checked by
authorized service personnel before
plugging in.
This humidifier is designed for use with
the water bottle located to the right of the
upper grill, The water bottle holds 1.9 gaF
Ions of water. The humidifier should be
positioned where it will be operating.
To fill the whole house humidifier, grasp
the bottle handle at the top of the bottle
and lift it straight up and away from
humidifier base. Take care not to bump
or damage spring valve assembly on bot-
tom of bottle.
NOTE: If it is desired to use approved
bacteriostat, follow directions correctly,
The bottle of the whole house humidifier
will hold 1.9 gallons of water,
The water bottle is designed with an "E-Z-
Fill Side-Cap", Remove the "E-Z-Fill Side-
Cap" on the side of the water bottle by
twisting counterclockwise.
Place the opening of the water bottle
under a water faucet and fill. If desired,
add Sears liquid bacteriostat (stock num-
ber 42-14900) to help control the build up
of bacteria and algae. Do not use solid
water treatments. Solid debris could make
the lower valve leak.
Install the "E-Z-Fil! Side-Cap" by twisting
clockwise. Hand tighten only,
Check for possible leaks by perform°
ing the following:
1, Grasp bottle handle and hold the bottle
upright over a sink.
2, Press up on valve plunger for about
one second to let out a little water.
3, Release the plunger.
/
/
_se
/
/
Spring VaUveAssemMy
4, Listen for air bubbles. Look for leaks
around the "E-Z-Fill Side-Cap" and
valve plunger.
5, If you hear air bubbles or see leaks,
retighten the ' E-Z-Fill Side-Cap" and
repeat steps 1-4,
Wipe off excess water from the bottle.
Positionthewaterbottlebackintothe
humidifierbasetotherightofthegrille.
The"E-Z-FillSide-Cap"mustbefacing
outward.Whenpositionedproperly,the
plungerwillopenandwaterwillflowinto
thebase.Thebasewillholdtheentire
Thewaterbottlemaybefilledatanytime
asnecessaryduringoperation.Tobenefit
fromlessfrequentfillingletthehumidifier
exhaustboththewaterfromthebottle
andbasebeforefilling.
Theunitisnowreadyforoperation.
contentsofthewaterbottle.Allowupto
oneminuteforthewatertoflowintothe
base.Oncethebottleisempty,removeit
andrefillitasmentionedearlier.Returnit
totherightsideofthegrille.Thehumidifi-
erisnowfilledtocapacity.
Operating Humidifier Controls
The operating controls of your Kenmore
Quiet Comfort whole house humidifier are
located towards the front of the humidifier.
Familiarize yourself with the controls.
Reference the diagram of the control area
for the correct nomenclature used in this
manual.
To Operate the Controls
Power Light
When the unit is plugged in and turned
on, the red power light will come on. It
will stay on until the unit is turned off ( _ )
or unplugged.
Humidity Control:
Adjust the amount of
humidity depending on your needs. The
humidifier will turn on and off as required
to maintain level of humidity selected. A
medium setting (half way between the
controls rotation) is recommended, but
there are times when low or high amount
of humidity may be preferred. For con-
stant operation of humidifier, rotating the
control all the way clockwise allows for
the maximum amount of humidity to be
evaporated into the air continuously.
IMPORTANT: Water damage may
result if condensation starts to form
on windows or walls, Humidity Control
setting should be lowered until
condensation no longer forms,
Speed Control O
This humidifier has a three speed fan con-
tro! switch. (.) - Low, (_) - Medium and
( } ) - High). The maximum humidity out-
put is obtained with the fan control on
high ( } ).
The higher the air flow speed, the more
water is evaporated and released into the
air. Low speed (.) is the quietest and is
also provided for conditions that may not
require as high an evaporation rate.
Refill Light
When the unit has a small amount of
water left in it, the amber refill light will
come on and the unit will automatically
shut off.
Humidity Control I Speed Control
Power Light
/ Off Position
Refill Light
Using Your Humidifier
Step 1
Be sure unit is full of water and plugged
in.
Step 2
Set the Speed Control to LOW ( _ ).
Step 3
Set Humidity Control to a medium position
(see diagram below)
NOTE: Humidifier should operate with
humidity control on the recommended
medium setting. If it does not, the humidi-
ty is at a relatively high level. To test the
unit under this condition, turn Humidity
Control all the way to clockwise and unit
should begin to operate. After the unit has
been tested, set Humidity Control to
medium or desired level.
Allow 24 hours for humidifier to adjust.
If humidity level in home is sufficient, the
humidifier will only operate with Humidity
Control set on maximum.
IMPORTANT: Water damage may
result if condensation starts to form
on windows or walls, Humidity Control
setting shoumd be Bowered until
condensation no monger forms,
Step 4
If humidifier stops running and the amber
Refill Light is not illuminated, the humidity
level is at the normal requirements for that
setting or it is adjusting to the home
conditions. The table below shows recom-
mended indoor humidity levels. The figure
below shows approximate relative humidi-
ty percentages which correspond to the
various settings of the Humidity Control.
Recommended
When Outdoor Indoor Relative
Temperature is: Humidity is:
-10°F 20%
0°F 25%
10°F 30%
20°F & above 35%
MIN
Operating Tips for Best Performance
1. Position the humidifier next to an
inside wal! at least 2 inches from the
wall and away from any heat
registers.
2. Do not restrict airflow from entering or
exiting the humidifier.
3. Use 42=14900 EPA approved
bacteriostat (available at your local
Sears store) to retard bacteria growth
that may cause odors and may be
harmful to your health.
4. Regular cleaning as instructed in
"Cleaning Your Humidifier" section of
this manual is recommended.
5. Replace the evaporative wicking filter
at least once per humidification
season or more depending on water
conditions in your area.
Relative Humidity
Replacement and Care of Filters
shock or injury from moving parts,
always unplug humidifier before
WARMNG: To reduce the dsk of
removing or replacing any parts.
CAUTION: To help retard bacteria
growth and keep maximum effic[em
cy, the fimter shoumd be replaced at
[east once per season, or more often
under hard water conditions. Use
Sears recommended replacement
filter 42o14g06.
To replace the filter in your humidifier,
follow the instructions below.
Unplug humidifier.
Before removing the filters, we recom-
mend moving the humidifier to an
area where floor coverings are not
susceptible to water damage. (i.e.
kitchen or bath areas.)
Remove the water bottle and set aside.
Be sure not to bump or damage the
lower spring valve.
Grasp housing
assembly
securely and
lift off
Grasp the housing assembly and lift
straight up and away from the base
and set aside. The filter is now acces-
sible.
4. Take note of the filter position.
Remove the filter and dispose of
properly. You may want to clean the
base at this time. See the "Cleaning
Your Humidifier" section of this manual.
Filter
Base
/I
Replacement and Care of Filters (continued)
Install a new filter (42°14906) into the
base. Coil the filter and position it
between the uprights in the bottom of
the base. The start and finish of the
coil should be captured at the center
of the base (see diagram) and the fi!-
ter should be resting on the floor of
the base.
Return the housing assembly to the
top of the base. Return the water bot-
tle to the right of the housing assembly
and reposition the humidifier to its
operating position,
7, The humidifier is now ready to be filled
for operation,
Base Uprights
\
Base
Position start
Return bottBe
to right side
of humidifier.
10
Loading...