Kenmore 66513099N413, 66513093N410, 66514313N410, 66514312N412, 66513802N710 Installation Guide

...

Kenmore 66513099N413, 66513093N410, 66514313N410, 66514312N412, 66513802N710, 66513803N710, 66513804N710, 66517389N710, 66517382N710, 66517383N710, 66515119K215, 66515119K216, 66515119K217, 66515119K218, 66515119K212, 66515119K213, 66515119K214, 66515114K216, 66515114K217, 66515114K218, 66515119K210, 66515114K212, 66515114K213, 66515114K214, 66515113K217, 66515113K218, 66515114K210, 66515113K214, 66515113K215, 66515113K210, 66515113K211, 66515113K212, 66515112K213, 66515112K214, 66515112K215, 66515112K216, 66515112K217, 66515049K112, 66515112K210, 66515112K211, 66515112K212, 66515049K111, 66515043K112, 66515042K112, 66515039K112, 66515042K111, 66515023K112, 66515023K113, 66515032K112, 66514429N511, 66514422N510, 66514422N511, 66514423N510, 66514319N411, 66514319N412, 66514319N413, 66514313N413, 66514313N412, 66514313N411, 66514312N413, 66514312N410, 66514312N411, 66513492N410, 66513492N411, 66513492N412, 66513493N410, 66513493N411, 66513493N412, 66513499N410, 66513499N411, 66513499N412, 66513479N412, 66513479N411, 66513473N410, 66513473N411, 66513473N412, 66513479N410, 66513472N410, 66513472N411, 66513472N412, 66513289K118, 66513289K117, 66513289K116, 66513289K115, 66513289K114, 66513289K113, 66513289K112, 66513283K118, 66513289K111, 66513283K115, 66513283K116, 66513283K117, 66513283K113, 66513283K114, 66513282K118, 66513283K111, 66513283K112, 66513282K115, 66513282K116, 66513282K117, 66513282K114, 66513282K111, 66513282K112, 66513282K113, 66513279K117, 66513279K118, 66513279K116, 66513279K115, 66513279K114, 66513279K113, 66513273K116, 66513273K117, 66513273K118, 66513279K111, 66513279K112, 66513273K115, 66513273K114, 66513273K112, 66513273K111, 66513272K118, 66513272K114, 66513272K115, 66513272K116, 66513272K111, 66513272K112, 66513209N413, 66513209N410, 66513209N411, 66513209N412, 66513204N410, 66513204N411, 66513204N412, 66513202N412, 66513203N410, 66513203N411, 66513203N412, 66513202N411, 66513202N410, 66513099N410, 66513099N411, 66513099N412, 66513093N411, 66513093N412, 66513093N413, 66513073K217, 66513092N410, 66513092N411, 66513092N412, 66513092N413, 66513073K211, 66513073K212, 66513073K213, 66513073K214, 66513073K215, 66513073K216, 66513049K115, 66513049K116, 66513073K210, 66513049K111, 66513049K112, 66513049K113, 66513049K114, 66513044K116, 66513044K112, 66513044K113, 66513044K114, 66513043K116, 66513043K112, 66513043K113, 66513043K114, 66513042K114, 66513042K115, 66513042K116, 66513039K114, 66513039K115, 66513039K116, 66513042K111, 66513042K112, 66513039K112, 66513039K113, 66513033K113, 66513033K114, 66513033K115, 66513033K116, 66513033K111, 66513033K112, 66513032K113, 66513032K114, 66513032K115, 66513023K113, 66513032K111, 66513019K112, 66513019K113, 66513014K112, 66513014K113, 66513013K112, 66513013K113, 66513012K113, 66513009N510, 66513004N510, 66513003N510, 66513003N511, 66513002N510, 66513002N511, 66512413N412, 66512723K310, 66512093K210, 66213273K112, 66213279K112, 66213282K112, 66213283K112, 66213289K112, 66213044K112, 66213049K112, 66213033K112, 66213039K112, 66213042K112, 66213013K112, 66213014K112, 66213019K112, 66213023K112, 66515119K211, 66515114K215, 66515114K211, 66515113K216, 66515113K213, 66515112K218, 66515043K111, 66515033K112, 66514429N510, 66514423N511, 66514319N410, 66513273K113, 66513272K117, 66513272K113, 66513044K115, 66513044K111, 66513043K115, 66513043K111, 66513042K113, 66513039K111, 66513032K116, 66513032K112, 66513023K112, 66513012K112, 66513004N511, 66512723K311, 66512413N411, 66512413N410, 66213272K112, 66213043K112, 66213032K112, 66213012K112 Installation Guide

Installation Instructions

lnstrucciones de instalaci6n

Instructionsd'installation

English / Espafiol / Fran_ais

I<enmor

PlasticTub Undercounter Dishwasher Lavavaj"las empotrado con tina de

pl6stico

Lave-vaiseileencastr_ avec cuve en

plastique

P/N W10435038B Sears Brands Management Corporation

Hoffman Estates, IL 60179 U.S.A. www.kenmore.com www.sears.com

Sears Canada Inc. Toronto, Ontario, Canada M5B 2C3 www.sears.ca

TABLEOF CONTENTS

DISHWASHER SAFETY ............................................................. 2

INSTALLATION REQUIREMENTS ......................... •................... 3

Tools and Parts..................................................................•................3

Location Requirements .....................................................................4

Drain Requirements...........................................................................6

Water Supply Requirements ...........................................................6

Electrical Requirements....................................................................6

INSTALLATION INSTRUCTIONS ............................................. 7

Prepare Cabinet OpeningmExisting Utilities.............................. 7

Prepare Cabinet OpeningmNew Utilities..................:................ 7

Prepare and Route Water Line.......................................................8

Install Drain Hose...............................................................................9

Prepare Dishwasher.........................................................................11

INSTALLATION INSTRUCTIONS (CONT.)

Make Power Supply Cord Connection................................_........12

Determine Cabinet Opening .........................................................14

Choose Attachment Option ............................................................15

Prepare Water Supply Line...........................................................16

Move Dishwasher Close to Cabinet Opening ............................ 16

Connect to Water Supply .............................................................18

Connect to Drain ............................................................................. 18

Make Direct Wire Electrical Connection.................................... 19

Secure Dishwasher in Cabinet Opening ......................................21

Complete Installation......................................................................22

Check Operation .............................................................................23

If Dishwasher Does Not Operate .................................................23

Additional Tips.................................................................................23

DISHWASHER SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance, Always read and obey all safety messages.

This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately follow instructions.

ii ,,,,,,

You can be killed or seriously injured if you don't follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

You Need to.

• Slowly open dishwasher door while someone grasps the rear of the dishwasher. Remove shipping materials, drain hose and lower rack. Close dishwasher door until latched.

• Observe all governing codes and ordinances.

• Install this dishwasher as specified in these instructions.

Tip Over Hazard

Do not use dishwasher until completely installed. Do not push down on open door.

Doing so can result in serious injury or cuts,

• Installation should be performed by a qualified service technician. The dishwasher must be installed to meet all

electrical and plumbing national and local codes and

ordinances.

INSTALLATION REQUIREMENTS

Tools and Parrs

Gather the recommended tools and parts before starting installation. Read and follow the instructions provided with any

tools listed here.

All Installations Tools needed:

Parts needed:

Other partsyoumay also need:

NOTE-. Parts available for purchase in plumbing supply stores.

Check local codes. Check existing electrical supply. See "Electrical Requirements" section. It is recommended that

electrical connections be made by a licensed electrical installer.

In addition, for first-time installations

Toolsneeded:

*Must be the proper size to connect your household wiring

to 16-gauge wiring in dishwasher.

Other useful items you may need:

Parts supplied:

Ur_lITt_!iii:i!:il

de_.mognt

ii i1_¸ i if -i ¸¸

Make sure all these parts are included in the literature package.

Parts needed:

I®TORX and T20 are registered trademarks of Saturn Fasteners, Inc.

Loca n Requirernen

Grounded electrical supply required. Do not run drain lines,water lines or electrical wiring where they

can interfere with or contact dishwasher motor or legs. The location where the dishwasher will be installed must provide

clearance between motor and flooring. Motor should not touch the floor.

Do not install dishwasher over carpeted flooring.

Shelter dishwasher and water lines leading to dishwasher against freezing. Damage from freezing is not covered by the warranty.

A side panel kit isavailable from your dealer for installing your dishwasher at the end of your cabinetry.

A moisture barrier accessory (Part Number 4396277) is available from your dealer for installing underneath the

countertop.

Check/ocation where dishwasher will be installed. The location must provide:

• easy access to water, electricity and drain.

convenient access for loading and unloading dishes.

Corner locations require a 2" (5.1 cm) minimum

clearance between the side of the dishwasher door and the wall or cabinet.

• square opening for proper operation and appearance.

• cabinet front perpendicular to floor.

• level floor. (If floor at front of opening is not level with

floor at rear of opening, shimsmay be needed to level dishwasher.)

Helpful Tip: Be sure to accurately measure dimensions and ensure dishwasher is level if the floor in the dishwasher Opening

isuneven (example: Flooring extends only partway into opening).

NOTE: Toavoid shifting during dishwasher operation, shims

must be securely attached to the floor.

If dishwasher will be left unused for a period of time or in a location where it may be subject to freezing, have it winterized

by authorized service personnel. Make sure pipes, wires and drain hose are within the shaded

area shown in the "Product and Cabinet Opening Dimensions" section.

Product and Cabinet Opening Dimensions

Check that all surfaces

lave no protrusions that w_uid

libit dishwasher installation.

Drain Requirement

A new drain hose is supplied with your dishwasher. If drain

hoseis not long enough, use a new drain hosewith a maximum length of 12 ft (3.7 m) (Part Number 3385556)

that meets all current AHAM/IAPMO test standards, is

resistant to heat and detergent, and fits the 1" (2.5 cm) drain_ connector of the dishwasher.

Make sure to connect drain hose to waste tee or disposer inlet above drain trap in house plumbing and 20" (50.8 cm)

minimum above the floor. It is recommended that the drain hose either be Jooped up and securely fastened to the

underside of the counter, or be connected to an air gap.

Electrical Requirernents

Be sure that the electrical connection and wire size are

adequate and in conformance with the National Electrical Code, ANSI/N1:PA 70 - latest edition and all local codes and ordinances.

A copy of the above code standards can be obtained from:

National Fire Protection Association 1Batterymarch Park Quincy, MA 02169-7471

You must have.

• 120-volt,.60 Hz, AC-only, 15- or 20-amp, fused electrical

supply.

• Copper wire only. We recommend..

• A time-delay fuse or circuit breaker.

• A separate circuit.

If connecting dishwasher with a

power supply cord:

• Use UL Listed power supply cord kit (Part Number 4317824) marked for

usewith dishwasher.

Make sure to usean air gap if the drain hose is _onnected to house plumbing lower than 20" (50.8 cm) above subfloor or

floor. Use 1.,_,,minimum I.D. drain line fittings.

If required, the air gap should be installed in accordance

with the air gap installation instructions.When you are connecting the air gap, a rubber hose (not provided) will be needed to connect to the waste tee or disposer inlet.

Water Supply Requirements

A hot water line with 20 to 120 psi (138 to 862 kPa) water

pressurecan be verified by a licensed plumber. 12001:(49°C) water at dishwasher.

3/8"O.D. copper tubing with compression fitting or flexible

braided water supply line (Part Number 4396897RP). NOTE. 1/2"minimum plastic tubing is not recommended.

A 90 ° elbow with 3A"hose connection with rubber washer.

Do not solder within 6" (15.2 cm) of the water inlet valve.

Power supply cord must plug into a grounded

3 prong outlet, located in the cabinet next to

the dishwasher opening. Outlet must meet all

local codes and ordinances.

If connecting dishwasher with direct wiring:

• Use flexible, armored or nonmetallic sheathed, copper wire

with grounding wire that meets the wiring requirements for your home

and local codes and ordinances.

• Use a UL Listed/CSA Approved strain relief.

INSTALLATION INSTRUCTIONS

Electrical Shock Hazard

Disconnect electrical power at the fuse box or circuit breaker box before installing dishwasher.

Failure to do so can result in death or electrical shock.

Prepare Cabine_ Opening--Existing Utilities

If the water line and the cable extend to the locations shown,

proceed to the "Install Drain Hose" section. If they do not reach

far enough, follow the instructionsin the "Prepare Cabinet OpeningmNew Utilities" section.

Prepare Cabine_ Opening_New Utilities

Prepare and route the electrical supply

Option A, Power Supply Cord.

NOTE:A grounded 3 prong outlet is required insidea cabinet next to the dishwashercabinet opening.

Drill a 11,_,,(3.8 cm) hole in cabinet side or rear.

See "Product and Cabinet Opening Dimensions" section.

Wood cabinet: Sand the hole until smooth.

Metal cabinet: Cover hole with grommet included with power

supply cord kit.

Route cable from power supply through cabinet hole (cable

must extend to the right front side of cabinet opening). Tape cable to the floor in area shown. This will prohibit cable from

moving when dishwasher ismoved into cabinet opening.

Option B, Direct Wire:

Helpful Tip: Wiring the dishwasher will be easier if you route the

cable into the cabinet opening from the right-hand side.

Drill a 11/_,,(3.8 cm) hole in right-hand cabinet side or rear. See "Product and Cabinet Opening Dimensions"section.

Prepare and Route Water Line

Helpful Tip. Routing the water line through the left side of cabinet opening will make water connection easier.

Drill a 1.,_,,(1.3 cm) hole in the cabinet side or rear.

Wood cabinet: Sand the hole until smooth. Metal cabinet: Cover hole with grommet (Part Number 302797

- not provided).

Measure overall length of copper tubing for the water supply line.

Attach the water supply line (copper tubing or flexible braided line) to the hot water line using a connection configuration that is in compliance with local codes and ordinances. The water

supply to the dishwasher should have a manual shutoff valve

located under the sink.

Slowly route water supply line through hole in cabinet. (If you

are using copper tubing, it will bend and kink easily, so be

gentle.) It should be far enough into the cabinet opening to connect it to the dishwasher inlet on the front left side of the

dishwasher.

Route water line and tape it to the floor in area shown. This will keep it from moving when dishwasher is moved into cabinet opening.

Install Drain Hose

IMPORTANT- Always use a new drain hose. Check local codes to determine whether an air gap is required.

If needed, drill a 11,_" (3.8 cm) diameter hole in cabinet wall or side of the opening closest to the sink.

Slowly turn water shutoff valve to "ON" position. Flush water into a shallow pan until clear to get rid of particles that could

clog the inlet valve. Turnshutoff valve to "OFF" position.

Route drain hose as shown through hole in cabinet to the front center of opening where drain connection will be made. Tape

drain hose to the floor in area shown. This will prohibit it from moving when dishwasher ismoved into cabinet opening.

IMPORTANT- The drain hose connection of the disposer or a

waste tee must be made before the drain trap and at least

20" (50.8 cm) above the floor where the dishwasher will be installed.

Helpful Tip: Toreduce vibration of the hose, keep the hoseaway

from the floor.

I. Fit rubber end of drain hose to

waste tee and cut if needed.

NOTE: Do not cut ribbed section.

2. Attach rubber end of drain hose to waste tee with a large drain hose

clamp (provided). Use pliers to squeeze clamp open and move into

position. If the drain hose was cut, : use a 11/2'' to 2" (3.8 to 5 cm) screw- type clamp (not provided).

Option C, Waste disposer - with air gap

"Option A, Waste disposer - no air gap

Using a hammer and screwdriver, knock plug into disposer.

2. Use needle-nose pliers to remove

plug.

Attach drain hose to disposer inlet with barge drain hose clamp

(provided). Use pliers to squeeze clamp open and move into position.

Option B, No waste disposer- no air gap

hose

Waste disposer - with air ga. i ..............................................

Using a hammer and Screwdriver, knock plug into disposer.

Use needle-nose pliers to remove

plug.

Connect rubber end of drain hose to air gap and cut if needed.

NOTE: Do not cut ribbed section.

Attach drain hose to air gap with large drain hose clamp (provided).

Use pliers to squeeze clamp open and move into position. If the drain

hose was cut, use a 11/2'' to 2" (3.8 to 5 cm) screw-type clamp (not

provided).

Use a rubber hose (not provided) with screw-type clamps (not

provided) to connect from air gap to disposer inlet.

Option D0No waste disposer- with air gap

Connect rubber end of drain hose

to air gap and cut if needed.

NOTE: Do not cut ribbed section.

Attach drain hose to air gap with

large drain hose clamp (provided). Use pliers to squeeze clamp open

and move into position. If the drain

hosewas cut, use a 11_" to 2" (3.8 to

5 cm) screw-type clamp (not provided).

Prepare Dishwasher

Tip Over Hazard

Do not use dishwasher until completely installed. Do not push down on open door.

Doing so can result in serious injury or cuts.

Excessive Weight Hazard

Use two or more people to move and install

•dishwasher. Failure to do so can result in back or other injury.

Use a rubber hose(not provided) with screw-type clamps (not

provided) to connect from waste tee to air gap,

Using the precut slots in the insulation, fasten the insulation over

the molded tabs on the tub. Be sure to fasten the insulation

down on both sides of the tub. Helpful Tip: Place cardboard under dishwasher until installed in

cabinet opening to avoid damaging floor covering. Do not use

door panel as a worktable without first covering with a towel to avoid scratching the door panel.

Using two or more people, grasp sides of dishwasher door

frame and place dishwasher on its back.

Using a flat-blade screwdriver, turn the plastic fasteners 1/4turn

counterclockwise to unlock them. Remove the panel. Do not remove tech sheet from access panel.

Install a UL Listed/CSA Approved strain relief. Make sure screwheads are facing to the left when tightening conduit nut.

Strain relief is provided with the power supply cord kit.

NOTE= If using Option B, proceed to "Determine Cabinet Opening," to continue with the installation of your dishwasher.

Make Power Supply Cord Connection

Using a 1,_,,hex head socket, nut driver or Torx®T20®

screwdriver, remove terminal box cover. Retain for later use.

Option A, Power Supply Cord;

Route cord so that it does not touch dishwasher motor to lower part of dishwasher tub. Pull cord through strain relief in terminal

box.

Select UL Listed/CSA Approved twist-on wire connectors rated to connect your power supply cord to 16-gauge dishwasher

wiring.

Electrical Shock Hazard

Electrically ground dishwasher,

Connect ground wire to green ground connector in terminal box.

Do not use an extension cord. Failure to follow these instructions can result in death,

fire, or electrical shock.

Connect wires black to black and white to white, using UL Listed/CSA Approved twist-on wire connectors.

Remove the green grounding screw and place through the ring terminal of the green ground wire. Reattach and tighten the

green screw.

NOTE: Do not pre-twist stranded wire. Twist on wire connector. Gently tug on wires to be sure both are secured.

Tighten strain relief screws to secure cord.

Placewires insideterminal box. Inserttabs on left sideof cover.

Make surewires are tucked insidebox. Close cover ensuring wires are not pinched. Use 1/4"nut driver or Torx®T20® screwdriver and previously removed screw to securecover.

NOTE: Do not plug into outlet until instructedto do so.

De ermine Cabine Opening

Your dishwasher has leveling legs. The following provides instructionsto adjust the leveling legs to set the dishwasher to

the correct height for your cabinet opening.

Measure height of Cabinet opening from underside of countertop to floor where dishwasher will be installed (you will need to measure the lowest point on the underside of the

countertop and the highest point on the floor). Refer to "Dishwasher Height Adjustment Chart" to adjust the leveling

legs.

NOTE: If the minimum cabinet opening height is less than 337_" (86 cm), the rear leveling legs and spacers can be

removed for additional clearance. Thiswill allow the dishwasher to fit into a 331/_'' (85.1 cm) high cabinet opening, but the dishwasher will be more difficult to move. (Measurements are approximate. Rear and front leveling legs are preset at the

factory for 341/_" [87.6 cm].) Turnfront and rear leveling legs to the same height. Refer to

o"Dishwasher Height Adjustment Chart."

Built-up floors: If the kitchen floor is higher than the cabinet opening's floor - for example, the kitchen floor tile does not

extend into the cabinet opening - add shims as needed in the area shown to bring the dishwasher up to 331,'_'' (85.1 cm) below

the countertop.

NOTE: Shims must be securely attached to floor to avoid movement when the dishwasher is in use.

Choese Atach ent Op ien.

Option A, Countertop Attachmenf

_.]Insert bracket

Remove the brackets from the package and insert into the open slots on the left and right-hand top of the dishwasher collar as

shown.

Bend tab

Excessive Weight Hazard

Use two or more people to move and install dishwasher,

Failure to do so can result in back or other injury.

Using 2 or more people, stand the dishwasher up.

IMPORTANT: The dishwasher must be secured to the cabinet.

There are two brackets found in the parts bag. Attach the

brackets using Option A if the countertop is wood, laminate or

another similar surface. If your countert°p is marble, granite or another hard surface, install using Option B.

Using a pair of pliers, bend the tab down to secure the bracket in place. Repeat this step for the other side.

NOTE: Do not attach the dishwasher. This will be done later.

Option B, Side Attachment

For marble, cjranite_ or other hard surface countertops With another person holding the rear of the dishwasher to keep

it from tipping, open dishwasher door and place towel over pump assembly and spray arm of dishwasher. This will keep

screws from falling into pump area when you are securing dishwasher to cabinet.

Plastic_'_ /l_'_

button

Push the plastic buttons out of the side of the tub. NOTE: Save the buttons tO cover the holes after dishwasher is

installed.

° •15

Push bracket into slot on the side of dishwasher, and bend tab in

toward the side of the dishwasher so that it keeps the bracket in place. Repeat this step for the other side of the dishwasher.

NOTE: Do not attach the dishwasher. This will be done later.

Prepare Water $uppty Line

Flexible braided connection: Secure nut to elbow using _" open

ended wrench or adjustable wrench.

NOTE: Do not use Teflonet tape with compression fittings.

Move Dishwasher Close to Cabinet Opening

Excessive Weight Hazard J

Use two or more people to move and install dishwasher.

Failure to do so can result in back or other injury.

NOTE: Do not install kick plate until instructed to do so

Copper tubing only: Slide nut, then ferrule, about 1" (2.5 cm)

onto copper tubing.

NOTE: To avoid vibration during operation, route the water supply line so that it does not touch the dishwasher base, frame or motor.

Connect the %" compression fitting to the water supply line prior to installing the unit into the cabinet opening. Attach such

that the _" connection is facing upward as shown above. Copper tubing only: Put the tubing into the 90 ° elbow fitting as

far as it will go (the copper tubing bends and kinks easily). Slide

the nut and ferrule forward and start the nut onto the elbow threads.

IMPORTANT: Double-check correct placement of utilities. Grasp

the sides of the dishwasher at the edges of the door panel. Move dishwasher close to cabinet opening.

NOTE: Do not push on the front Of the panel or on the console. Panel or console may dent.

Helpful Tip: Temporarily tape utilities to the floor in the locations

shown to prohibit them from moving when dishwasher is moved

into the cabinet opening.

Check that water line is on the left side of opening and drain hose is near the center of the cabinet opening.

"I'®TEFLON is a registered trademark of E.I. Du Pont De Nemours and Company.

Move dishwasher into cabinet opening

With another person holding the dishwasher to keep it from

tipping, open and close the door a few times. If the door closes

or falls open under its own weight, the door tension will need to be adjusted.

If the door closestoo quickly, decrease the spring tension by

moving the spring end toward the front of the dishwasher. NOTE. Springs should be in the same notches on left and right

sides.

IMPORTANT: If rear leveling legs and spacers were removed, cover the floor when moving the dishwasher toavoid damage

to the floor. Slowly move dishwasher completely into cabinet opening. Do not kink or pinch water line, drain hose, power

supply cord or direct wire between dishwasher and cabinet. Remove cardboard from under dishwasher.

NOTES:

• It is all right if dishwasher fits tightly into cabinet opening. Do not remove insulation blanket - the blanket reduces the sound level.

• If using power cord, make sure to route end through hole in cutout before sliding dishwasher into cabinet opening.

If the door falls open, increase the spring tension by moving the

spring end toward the back of the dishwasher.

NOTE: Springs should be in the same notches on left and right

sides.

Align front of dishwasher door panel with front of cabinet doors. You may need to adjust alignment to be even with your

cabinets.

Check that leveling legs are firmly against the floor. Close and latch the door, and place level against the front panel. Check

that dishwasher is centered from front to back in the opening. If

needed, adjust leveling leg until dishwasher is plumb. Repeat for

other side of dishwasher.

Helpful Tip.. Pushup on front of dishwasher to raise dishwasher

off the ground to adjust front legs. With some installations, it

may be easier to adjust the front leg using the 3As"hex head

socket or adjustable wrench.

Connect to Water Supply

Be sure rubber washer is properly seated in fitting. Slide the 3A"fitting up to the valve and hand tighten to avoid cross- threading. Hand tighten until the coupling istight.

Using pliers, check the tightness of the coupling. An additional 1/4to 1/2turn may be required to seal the rubber gasket.

NOTE- Do not overtighten. Damage to the coupling can result.

Place level against top front opening of tub. Check that dishwasher is level from side-to-side. If dishwasher is not level,

adjust front legs up or clown until dishwasher is level. Close the dishwasher door.

Place paper towel under 90 ° elbow fitting. Turnon water supply and check for leaks. If leak occurs, repeat previous step.

Connectto Drain

Drain hose

Drain hose stop

Place towel under drain hose to catch any water in drain hose.

Place the small drain hoseclamp onto the small end of the drain hose. Pushthe new drain hose into the black drain hose

connector up to the drain hose stop.

Usingpliers,squeezeopenthesmalldrainhoseclampandslide

ontoconnectorbetweenstops.

Mak Direct Wire Electrical Connection

NOTE: If the power supply cord was connected earlier, proceed to "Secure Dishwasher in Cabinet Opening" section.

Option B, Direct vvrire:

Route cable so that it does not touch dishwasher motor or lower part of dishwasher tub. Pull cable through UL Listed/CSA

Approved strain relief in terminal box. Strain relief isnot supplied with the dishwasher. Owner must purchase a 7_,, screw-

in type strain relief. Select UL Listed/CSA Approved twist-on wire connectors (not

included} rated to connect your household wiring to 16-gauge dishwasher wiring. "

After hose is connected, remove towel.

Electrical Shock Hazard

Electrically ground dishwasher. Connect ground wire to green ground connector in

terminal box. Do not use an extension cord. Failure to follow these instructions can result in death,

fire, or electrical shock.

Connect wires black to black and white to white, using•UL Listed/CSA Approved twist-on wire connectors (not included).

Wiring configuration

Form bare ground wire into a U-shaped hook. Wrap ground wire hook clockwise around ground connector screw and under

the washer. Securely tighten ground connector.

Tighten strain relief screws to secure cable.

Place wires inside terminal box. Insert tabs on left side of cover.

Make sure wires are tucked inside box. Close cover ensuring wires are not pinched. Use 1/_,,nut driver or Torx®T20® • screwdriver and previously removed screw to secure cover.

NOTE. Do not pre-twist stranded wire. Twist on UL listed/CSA approved wire connector. Gently tug on wires to be sure both

are secured.

Secure Dishwasher Cabinet Opening

Checkthat dishwasherisstilllevel front-to-back and side-to- side in cabinet opening.

Secure dishwasher to countertop Locate brackets on top of dishwasher and secure dishwasher to

countertop with two, #10 x 1_,, Phillips-head screws (included). The dishwasher must be secured to keep it from shifting when

door is opened.

Side mount dishwasher to cabinet NOTE: If side mounting dishwasher to cabinet, you must drill

pilot holes in cabinet to avoid splitting the wood. Locate brackets on side of dishwasher and secure dishwasher to cabinet with two, #10 x 1,_,,Phillips-head screws (included). The

dishwasher mustbe secured to keep it from shifting when door is opened.

Open dishwasher door, remove lower dish rack, and place towel over pump assembly and lower spray arm of dishwasher. This will keep screws from°falling into pump area when you are securing the dishwasher.

NOTE. Do not drop screws into bottom of dishwasher.

Check that top of door does not contact screws, brackets or countertop. If it does, adjust leveling legs.

Open door and check that space between dishwasher cabinet

opening and tub is equal on both sides. If spacing is not equal,

loosen bracket screws secured and shift tub. Tighten bracket screws.

Remove towel from dishwasher. Reinstall the lower dish rack.

PlaCe the plastic access panel against the dishwasher leg.

Check that the lower edge of the access panel touches the floor. Adjust if necessary.

Using a flat-blade screwdriver, turn the fasteners 1/_turn

clockwise to lock into place. The fasteners slot will be straight Up and down when properly locked.

+ 50 hidden pages