Kenmore 625384480 Owner’s Manual

OWNER'S MANUAL
Heavy ,yWhole House Water Filter
MODEL NO. 625.384480
Caution:
Read and follow all safety rulesand operating instructions before first use of this product.
Questions ? Visit www.KenmoreWater.com
or call toll free 1-800-426-9345 (M - F, 7AM - 8 PM CST)
Repair or Parts? Call toll free 1-800-469-4663
See back cover for other Sears service numbers.
SAVE THIS MANUAL
Sears, Roebuck and Co., 3333 Beverly Road, Hoffman Estates, IL 60179 U.S.A.
Warranty
Installation
How ItWorks
Care Of
Specifications
Repair Parts
_K_n_t.KerlllloreWater.com Part No.7295232 (Rev. B 2/26/08)
ONE YEAR FULL WARRANTY ON THE
HEAVY DUTY WHOLE HOUSE WATER FILTER
When installed, operated and maintained according to all instructions supplied with the product, if this Heavy Duty Whole House Water Filter fails due to a defect in material or workmanship within one year from the date of purchase, Sears will replace this Heavy Duty Whole House Water Filter free of charge. This warranty does not include filter cartridges, which are expendable items.
This warranty is available by simply returning the Heavy Duty Whole House Water Filter to the nearest Sears store throughout the United States.
This warranty applies only while this product is in use in the United States or Canada.
This warranty gives you specific legal rights, and you may have other rights which vary from state to state.
Sears, Roebuck and Co., Hoffman Estates, IL 60179
14-1/8"
-_7-1/4"_ -_ 7-1/4" _
Questions? Call The Kenmore Water Line 1=800=426=9345 or visit KenmoreWater.com
Unpack and Check Shipment ............................................................................. 4
Water 'lYeatment Filter Cartridges ......................................................................... 5
Plan Your Installation ................................................................................... 5
Typical Installations ..................................................................................... 6
Installation ........................................................................................... 7-9
Filter Cartridge Life & Installation ....................................................................... 10
Specifications .......................................................................................... 11
Exploded View & Parts List ............................................................................. 11
Y Read this entire manual carefully before installing and
using your Heavy Duty Whole House Water Filter. Follow all steps exactly to correctly install.
V Check with your local public works department for
plumbing and sanitation codes. You must follow
their guides as you install the system. Follow your local codes if they differ with guides in this manual. In Massachusetts, plumbing codes of Massachusetts
shall be adhered to. Consult with a licensed plumber.
Y Maximum operating pressure: 100 psi.
Y Maximum temperature: 100°F.
Y For cold water use only. Do not install on a hot water
line.
Y Not to be used on water that is microbiologically
unsafe or of unknown quality without adequate disin- fection before or after the system.
Y Keep solvents and sprays away from the clear sump
housing material. Surface cracking and failure can result.
V Do not install where pressure surges exceed 100 psi.
Install a pressure regulator before the filter if needed.
Y Do not install outdoors in direct sunlight.
Y Do not install where freezing may occur.
Y Misapplication of clear housing voids your warranty.
Y It is important to properly seat the o-ring in the
groove of the sump housing, or a water leak could
OCCUr.
Y Retighten the sump 7 days after replacing filter.
Questions? Call The Kenmore Water Line 1=800o426=9345 or visit KenmoreWater.com
INSPECT SHIPMENT Your Heavy Duty Whole House Water Filter is shipped
complete in one carton. Remove all items from your shipping carton.
Check all items against the packing list below: Note any items lost or damaged in shipment. Note any damage to the shipping carton. Refer to the exploded view and parts list in the back of the manual for the part names
and numbers of missing or damaged items. If problems exist, refer to the website or the toll free number listed
throughout this manual. Keep the small parts in the parts bag until you are ready
to install them.
NOTE: Codes in the state of Massachusetts require installation by a licensed plumber.
If you live in the state of Massachusetts, review plumb- ing code 248-CMR of the Commonwealth of Massachusetts before proceeding with the installation.
Heavy Duty Whole House
Water Filter Assembly
Sump Wrench
BagAssembly
Mounting
Screws
Mounting Bracket
Questions? Call The Kenmore Water Line 1=800-426=9345 or visit KenmoreWatencom
Filter cartridges to remove (1) sediments, and (2) tastes, odors and sediments are available for use in the Heavy Duty Whole House Water Filter. Filter cartridges are not
included with this water filter. Your Sears store has a selection of the different types of filter cartridges avail-
able.
SEDIMENT FILTER CARTRIDGES
Sediment cartridges remove sand, silt, clay, rust, dirt, and other sediments from water. For example, a 30
micron cartridge filters larger sediments, and allows
higher flows at less pressure drop. A 5 micron cartridge
filters finer sediments from water, often to a single faucet.
TASTE & ODOR CARTRIDGES
Many bad tastes and/or odors are reduced from water using an activated carbon cartridge. It is most often
used to remove chlorine taste and odor. The 'Ihste and Odor Cartridge available is for taste and
odor reduction, and sediment reduction.
INSTALLATION LOCATION
'lkofilter sediments or tastes and odors from all house water, locate the Heavy Duty Water Filter on tlle main
water supply pipe (See Figure 1). You can also filter water to one faucet. For example, install the filter under the kitchen sink to filter the cold drinking water (See
Figure 2).
PLANNING YOUR INSTALLATION
When planning the installation, first read the preceding filter cartridge information to determine where to locate the water filter housing. Then, use the drawings on Page 6 as a guide. There are many variables to consider as
you plan. Some of these are:
The Heavy Duty Water Filter inlet and outlet internal threads are 1" NPT
Existing plumbing type (copper, threaded, etc.) and nominal size (1/2", 3/4", 1" etc.)
'lkools you have, and your plumbing skills
Space available for installing the Heavy Duty Water Filter
To Outside Faucets
Cold Water
[o Houso
Faucets &
Water Heater
Filtering All House Water
City Water Supply
-1
Pressure
Tank
Heavy Duty
Water Filter
Filtering Water to One Faucet
2°;
ell Water Supply
Pump
Well _
Figure 1
Make a simple sketch of your proposed installation, and a list of plumbing materials you will need. Obtain
everything you need before starting the installation.
Questions? Call The Kenmore Water Line 1-800-426-9345 or visit KenmoreWater.com
HOT
A. INSTALLATION ON COPPER PLUMBING USING COMPRESSION FITTINGS
MATERIALS & TOOLS NEEDED
Apply 4 wraps of Optional WATER
Teflon Tape Shutoff Valve OUT
2 compression adaptors, 1" NPT x coin- pression end to fit existing copper pipe
Teflon tape
'I_lbing cutter
Sandpaper or emery cloth
2 wrenches, either open end or adjustable
Op tional Nu t
Shutoff
Valve Brass
jaw, sized to fit compression adaptors
WATER f
IN
NOTE: Be sure to allow a minimum space of 2" under the
filter for removing the sump (to change the cartridge). Figure 3
B. SOLDERED COPPER INSTALLATION
WATER WATER
IN OUT
f
Ferrule
Compression
Adaptor
INLET 1" NPT
D. UNDERSINK INSTALLATION
(Filtering Water to One Faucet)
Optional 1" Co e_ lilt Ill _ adaptol. 1" N!_T
Shutoff PP'" IIIII [[Jl x Sweat (Apply
Valve (2) Pipe: as Illll ]HI 4 wraps of
reqmred IIII/ /IJJ Teflon Tape)
See Note in Figure _ Figure 4
C. THREADED INSTALLATION
WATER
OUT _JATERuT
IN_ _T
Optional 1"
Shutoff Nipple
Valve (2) (2)
See Note in Figure 3
1" Hex Nipple
(2)
Union
Fitting
(2)
Figure 5
II II
',', ',', SINK
Shutoff Valve
NOTE: To change the filter
cartridge, you Fnust
turn off fl_e water. A nearby shutoff
valve is convenient. Most sinks already
have shutoff valves on the supply pipes.
COLD
NOTE: Be sure to allow
a minimum space of 2" under
the filter for removing fl_e
sump (to change the cartridge).
Figure 6
Questions? Call The Kenmore Water Line 1-800-426-9345 or visit KenmoreWater.com
A. WATER FILTER ON HOUSE MAIN WATER PIPE, TO FILTER ALL HOUSEHOLD WATER
USING COMPRESSION FITTINGS (See Figure 3 on Page 6)
INSTALLATION STEPS
1. Apply 4 wraps of Teflon tape to the threads of both compression fittings.
2. Carefully turn the compression fittings into the water filter head inlet and outlet and tighten. Do not cross-
thread and damage the threads. Do not overtighten
and crack the head.
3. Remove the nut and brass ferrule from both compres- sion fittings and set aside. Using a tape measure or
ruler, measure the distance "D" as shown in Figure 7). Mark this dimension at right so you do not forget.
4. IMPORTANT: 'Ium off the water supply to the main pipe. Open a high and low faucet in the water system
to drain the pipe.
5. On the main water pipe, where you will install the fil-
ter, mark the dimension "D". You will remove this section of pipe. Before you begin to cut, double-check your measurement.
6. Use a tubing cutter to remove the section of pipe. Remove all burrs and rough edges with the sandpaper
or emery cloth.
7. Place a nut and brass ferrule from compression fittings onto both pipe ends (See Figure 8).
8. With the IN side of the water filter toward incoming water, spread the pipes apart and fit both pipe ends
into the compression fittings. Move a ferrule and nut up to the fitting (See Figure 9). Then, turn on and
tighten the nut. Hold the fitting with one wrench
while tightening the nut with the other. Repeat on the other side.
9. Before turning on the water supply, remove the sump from the filter head and install the filter cartridge (See
Page 10).
D
Nut Brass
Ferrule
!
Nut
WATER FLOW
D _ _
Measure to shoulder inside of fittings,
Copper pipe butts against this shoulder.
Figure 7
! \
Brass Nut
Ferrule
Figure 8
OUT
Brass Nut
Ferrule
Figure 9
GROUNDING INFORMATION:
Ground
The house cold water pipe is often used to ground elec- trical outlets in the home. Grounding protects you from
electrical shock. Installing the water filter housing may
Wi___
have broken this ground. 'lb restore, buy and install a #4
copper wire across the filtex, tightly clamped at both ends, as shown in Figure 10.
Clamp
(2) tt /t Figure 10
Questions? Call The Kenmore Water Line 1-800-426-9345 or visit KenmoreWater.com
B. WATER FILTER ON HOUSE MAIN WATER PIPE, TO FILTER ALL HOUSEHOLD WATER
USING SOLDERED COPPER FITTINGS (See Figure 4 on Page 6)
MATERIALS AND TOOLS NEEDED:
You will need 2 sweat adaptors, 1" NPT x sweat (sweat end to fit your main water pipe), lead-free solder and flux, soldering torch, '[_flon tape, sandpaper or emery
cloth, open end (to fit sweat adaptor) or adjustable jaw
wrench.
INSTALLATION STEPS
CAUTION: Heat created when soldering can damage the water filter's plastic parts. Be sure to use the follow- ing procedure to protect the water filter.
1. IMPORTANT: 'Ium off the water supply to the main pipe. Open a high and low faucet in the water system
to drain the pipe.
2. On the main water pipe, where you will install the fil-
rex, use a tubing cutter to remove a section of pipe about 12" long. Use sandpaper or emery cloth to thor- oughly clean and remove all burrs and rough edges, from both pipe ends.
NOTE: When soldering, use lead-free solder and flux
only. Be sure pipe and fittings are properly
cleaned.
3. Solder a sweat adaptor onto one of the pipe ends (See Figure 11).
4. Place, but do not solder, a straight connector onto the
other pipe end (See Figure 11).
5. Remove the sump from the filter head and set the sump aside.
6. After it cools, apply 4 wraps of Teflon tape to the
threads on the sweat adaptor fitting (See Figure 12).
7. With the IN side of the water filter toward incoming water, carefully, turn the filter head onto the sweat
adaptor fitting (See Figure 12). Do not cross-thread, or over-tighten and crack tlle filter head.
8. 'l\ml a sweat adaptor fitting into the other side of the filter head and hand tighten only. Using a tape meas-
ure or ruler, measure the distance "D" as shown in Figure 13. Mark this same dimension on a length of
copper pipe. Cut the length of pipe.
9. Remove the sweat adaptor fitting from the filter head and solder to the cut length of pipe.
10. After it cools, apply 4 wraps of Teflon tape to the
threads on the sweat adaptor fitting. Apply flux and
continued
place the pipe end of the soldered assembly into the straight connector. Then, turn the adaptor end into
the filter head and tighten.
11. Solder both sides of the straight connector.
12. Before replacing the sump and turning on the water supply, install the filter cartridge (See Page 10).
NOTE: Read the "Grounding Information" on Page 7,
and comply with the instructions if required to maintain continuity.
L __
\ !
Sweat Straight Adaptor Connector
Figure ii
Apply
Teflon Tape
/
Sweat
Adaptor
IN OUT
Filter
Head
WATER FLOW
Figure 12
Figure 13
Questions? Call The Kenmore Water Line 1=800-426=9345 or visit KenmoreWater.com
Loading...
+ 16 hidden pages