Kenmore 59677277790, 59677275790, 59677272790, 59668147790, 59668142791 Owner’s Manual

...

ORDER # 10937020

Owner's Manual

BOTTOM R REFRIGERATOR

Model Nos: 67272, 67277, 67275 77272, 77277, 77275, 68142, 68147

CAUTION:

Read and follow all safety rules and

operating instructions before first use of this

product

Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.

(Model 67272 shown)

. Safety Instructions ° Installation Information

', Operating Instructions

° Care and Cleaning , Troubleshooting

° Espa_ol

• Fran_ais

Electrical Requirements

Recognize this symbol as a safety precaution.

WARNING

Electrical Grounding Instructions--This refrigerator is equipped with a three-prong (grounding) plug for protection against possible shock hazards If you encounter a two-prong receptacle, contact a qualified electrician and have the two-prong wall receptacle replaced with a ptopedy grounded three-prong walt receptacle inaccordance with the National Electrical Codex

Refrigerator is designed to operate on a separate 103 to 126 volt, 15 amp°, 60 cycle Line Do not under any circumstances cut or remove the round grounding prong from the plug_

Refrigerator must be grounded at all times. Do not remove warning tag from power cord.

Do not use a two-prong adapter° Do not use an extension cord.

Proper Disposal of Your Refrigerator

IMPORTANT: Child entrapment and suffocation are not problems of the pasL Junked or abandoned

refrigerators are still dangerous--even if they will sit

for "just a few days." If you discard an old

refrigerator, please follow the instructions below to help prevent accidents.

BEFORE YOU THROW AWAY YOUR OLD REFRIGERATOR OR FREEZER:

Take off the doors.

Leave the shelves in place so that Children may not easily climb inside.

Contents

Electrical Requirements ........................................................2

Proper Disposal of Your Refrigerator ................................2

Installation Checklist ............................................................3

Installation Instructions ................................................ 4

Space Requirements ................................................................4

Leveling Refrigerator .........................................................4

Door Reversal .......................................................................4

Connect ice maker water supply line

(some models) ........................................................................6

Controls .....................................................................................7

Refrigerator and Freezer Controls .............................7

Selling Controls .....................................................................7

Refrigerator Features ...........................................................8

Refrigerator Shelves .......................................................8

Crisper Drawers .....................................................................8

Temperature Controlled Meat Drawer

(some models) ..........................................................................9

Bottle Rack (some models) ..................................................10

Covered Utility Bin (some models) ...........................10

Dairy Compartments (some models) ............................10

Door Buckets ....................................................................10

Tall Package Retainer ......................................................11

Door Shelves ..........................................................................11

Adjustable Divider (some models) ............................tl

Bottle Holder .....................................................................11

Freezer Features ..............................................................................12

Frost-Free System .................................................................12

Automatic ice Maker (some models) ............................12

Ice Service Rack .........................................................................12

Wire Shelf .................................................................. I3

Wire Basket ....................................................................................13

Ice Bin ...............................................................................................13

Care and Cleaning ...................................................................14

General Cleaning ........................................................................14

Adhesives ....................................................................................14

Door Gaskets .......................................................................14

Condenser Coils ......................................................................14

Glass Shelves ....................................................................14

Odor Removal ....................................................................14

Light Bulb Replacement .................................................15

Vacation Tips ..........................................................................15

EnergyTips ......................................................................15

Normal Operating Sounds ..............................................16

Before Calling For Service ...........................................................t7

Warranty .................................................................................19

Espan61..............................................................................................21

Fancais .........................................................................................42

Installation Checklist

Verify the following has been completed to ensure proper operation of your refrigerator

Doors

• Handles are solidiy attached ° Handle side of door is '/8" higher than hinge side of

door (See installation instructions page 6,)

° Doors seal completely to refrigerator cabinet

Leveling

o Refrigerator is tilted 1/: (6 mm) from front to rear and

level side to side.,

Ice Maker (some models)

• Water supply to refrigerator is attached and turned on

• Water leaks are not present at connection between household water supply and refrigerator, (After 24

hours check connection for water leaks.)

• Ice maker arm is in on position for ice production° (It may take up to 24 hours for first harvest of ice)

Electrical

• Properly ground 3-prong wall receptacle is used to plug in refrigerator

Read and Save These Instructions

Record in the space provided below the model and serial numbers found on the serial plate located on the top left wall of the refrigerator compartment,

Model Number: Serial Number:

Purchase Date:

Note

Translation may sometimes cause variations in meaning,

In all cases where meaning varies, the most accurate meaning will be the English version of this document

Installation Instructions

Proper installation will ensure this refrigerator operates

most efficiently

Space Requirements

,_WARNING: Keep flammable materials and

vapors, such as gasoline, away from refrigerator: Failure to do so can result in death, explosion, fire, or

burns.

To ensure proper-ventilation for your refrigerator, allow for a 1"(2.5 cm) space at the top of your refrigerator,

If your refrigerator has an ice maker, make sure you leave some extra space at the back to allow for the water line connection. The refrigerator can be flush with the back walt if you do not have an ice maker

installed.

If you are installing your refrigerator next to a fixed wall, leave 2 1/2"minimum on each side (depending on your model) to allow for the door to swing open

90°.

NOTE: Do not install the refrigerator near an oven, radiator, or other heat source, nor in a location where the

temperature will fall below 55°F (13°C)_

• Turn stabilizing leg (some models) clockwise until firmly against floor

Roller adjustment

screw

.4=

.z_........ -_

.// "_ -i ¸_

Bottom hinge _'_- Stabilizing leg cover (some models)

Door Reversal

Leveling Refrigerator

Some installations may require door reversa! to achieve full door swing. If so proceed to "Door Reversal" section before leveling your refrigerator.

If you_ refrigerator requires ice maker water' supply connection, proceed to "Connect ice maker water supply"

section on page 6 prior to leveling your refrigerator°

Plug in power cord

Move refrigerator into final location.

Level refrigerator using a level placed on top of the refr'igerator_

• Remove toe grille.. Remove bottom hinge cover if refrigerator has a stabilizing leg.

• Turn roller adjustment screws to raise or lower refrigerator cabinet. Front of refrigerator must be '/4" (6 ram), or _12bubble on your level, higher than

the back of your refrigerator:

• Make sure refrigerator cabinet is level from side to side by adjusting left and right roller adjustment

screw.

CAUTION: Protect soft vinyl or other flooring |

with cardboard, rugs or other protective material to avoid| property damage.

Some installations may require door reversal to achieve full door swing_To reverse door swing direCtion perform

the following steps: Tools Required

Putty knife (blade covered by masking tape) 5/_6"hex nut driver

3/B"hex nut driver

Phillips screwdriver Blade screwdriver

Remove and reverse refrigerator handle.

IMPORTANT: To prevent scratching of refrigerator surfaces, blade of screwdriver and putty knife called for in steps below must be covered with masking

tape.

• Pry up edge of handle trim using a putty knife with

the blade covered with masking tape. Remove

handle from door by removing 4 mounting screws

at each end of handle.

• Pry 4 button plugs from hinge side of door with

putty knife, blade covered with masking tape. Mount handle on opposite side of door using

mounting screws removed in previous step. If cabinet plug has a phillips type head use a phillips screwdriver to remove cabinet plug.

, Snaphandletrimintoplace°Replace4button 9,

plugsinemptymountingholes

Handletrim -_| :

Screw-_ 4!

Handle --,

Screw --_: Button /

Handle trim i-*] plugs \\

2. Remove top hinge cover° Top hinge cover snaps off. Remove top hinge and hinge shim using hex nut

driver,

3. Remove refrigerator door by lifting off of center hinge pin.

4, Remove center hinge pin using hex nut driver,, 5, Remove freezer door by lifting door off bottom hinge

An internal support rod may slide out of hinge socket.,

Replace rod before hanging door

6., Remove center hinge bracket and hinge shim using Phillips screwdriver

7 Remove toe grille and bottom hinge cover° Both snap

off

8 Remove bottom hinge and hinge shim using hex nut

driver.,

5/16" screws ,_,, ;

Top hinge _ , --

Remove freezer door handle.

• Pry up back edge of handle cap using a putty knife with the blade covered in masking tape Remove handle cap from handle. Remove handle from door by removing mounting screw at each side of

handle,

o Pry two button plugs from hinge side of door using

a putty knife with the blade covered in masking tape.

:_ /Handle

" __:z_=_ Screws

Button

, \

Freezer

handle

10 Reverse doors as necessary by performing the

following steps:

- Remove button plugs from opposite side of refrigerator cabinet using putty knife covered with

masking tape, Insert button plugs in holes left from hinge removal,

• Replace internal support rod in hinge side of freezer door prior to hanging door,

Support

rod

plug

5/16" '.... Center hinge

hex pin

.4 hinge

Center hinge / "._ } bracket

Phdhps screws -,'

Bottom hinge f<_:-;_:L.._ i

3/8"

screws _-------_ I:; _

11, Rehang doors by replacing bottom, center, and top

hinges, along with freezer and refrigerator doors on opposite side of refrigerator performing steps 2-8 in

reverse order.

• Use a penny at top to space door 3/4"(18 ram) from cabinet,

• Handle side of door should be approximately I/8" (3 mm) higher than hinge side. Door wilf

become level when it is loaded with food

_ CAUTION: Observe the following to avoid property damage:

• Make sure water pressure to water valve is between 20 and 100 pounds per square inch

o Tighten adapter fitting and nuts with pliers and

wrenches. Do not overtighten.

(18 mm)

1/8"

12 Mount freezer handle to opposite side of door using

mounting screws removed in previous step.

• Angle front edge of handle cap downward toward back lip of freezer handle.. Verify bottom tab on freezer cap slides under rear fip of freezer handle; Snap rear edge of handle cap in place, Place 2 button plugs in empty mounting holes,

Connect ice maker water supply line (some models).

, Check for water leaks and correct if necessary

before returning refrigerator to normal location. After 24 hours check again for leaks

Important

• Before connecting water supply, contact a plumber to connect copper tubing to household plumbing in

compliance with local codes and ordinances.

• DO NOT use piercing type or 3/1_"saddle valves! Both reduce water flow, become clogged with time and in

addition may cause leaks if repair is attempted The correct type of shut-off valve requires a 1/4"hole to be

drilled in the water supply pipe prior to valve attachment.

o Do not install copper tubing in area where

temperatures drop below 32° (0°)_

Materials Required t/4"O.D (6 mm) flexible copper tubing is required.. Length

of copper tubing must reach from water supply connection to water valve inlet port on back of refrigerator, plus additional 8 fL (2 m) of tubing for a service loop. A service loop will allow refrigerator to be

pulled away from the wall without disconnecting tubing_

Procedure

1,. Remove plastic cap from water valve inlet port,

,_WARNING: To avoid electrical shock which can cause severe personal injury or death. Disconnect

power to refrigerator before connecting water supply

Water valve inlet port

Controls

This refrigerator is designed to operate at normal household temperatures of 55° to 110°F (13° to 43°C)..

Refrigerator and Freezer Controls

Refrigerator control is located on upper rear wall of refrigerator section.

-J'°z

_"-Plastic

.L'!_, cap

Place brass nut and brass sleeve on copper tubing

(Brass nut and sleeve are found in your literature

packet°) Insert copper tubing into water valve inlet port. Connect brass nut on copper tubing to water valve inlet port Make sure copper tubing is secure by

pulling on copper tubing

• i _1 ii

,,. r._ ' ....... j'P clamp

I U:

i [

I !*_Copper

' _ i'' : :': " I tubing

: .i/I ;._:_ Brass sleeve

Water valve / '.t_ :;:!_ "-( ...........

/! -,.. :p; i o_

inlet port q) _' _-\,\ .......

• Brass nut

Turn on water supply to refrigerator and check for

leaks Correct any leaks at connection Be careful not to overtighten connection°

4•

Create a service loop using extreme care to avoid kinks. Secure copper tubing to refrigerator cabinet with a "P" clamp. It is important to secure copper tubing to refrigerator to avoid leaks when pushing refrigerator back into opening.

= ...................................... '

I )i

ij 21 'i )S !

;-,i J i

4 _

t 7 !i F

Freezer control is located on left front ceiling of freezer section

'ii

li;,: !-i: 4 -;i Coritrol i'

Setting Controls

When freezer control is set to OFF, neither refrigerator

nor freezer sections will cool. Initially, set both controls to 4. Wait 24 hours for refrigerator and freezer sections to stabilize temperatures After 24 hours, adjust controls, one number at a time, as desired 1 is warmest setting

and 7 is coldest. Set controls precisely using a household thermometer

with a temperature range between -5° to 50°F

(-21° to 10°C).

Put thermometer snugly between frozen packages in freezer section. Wait 5-8 hours° If freezer temperature is

not 0° to 2°F (-17° to -16°C), adjust freezer control 1 number at a time, Check again after 5-8 hours.

Put thermometer in a glass of water in middle of refrigerator section. Wait 5-8 hours, if refrigerator temperature is not 38° to 40°F (3° to 4°0), adjust

refrigerator control 1 number at a time. Check again after 5-8 hours

Refrigerator Features

Refrigerator Shelves

Shetves adjust to meet individual storage needs. Some models feature spill-saving shelves and slide out shelves. Spill-saving shelves hold minor spills for easier cleaning

,i_ CAUTION: Make sure shelf is secure before replacing items on shelf to avoid property damage

tempered glass shelves

carefully to avoid personaI injury or property damage. Shelves may break suddenly if nicked, scratched, or exposed to sudden temperature change

o Remove shelves by lifting up shelf front, releasing

hooks from metal track, then pulling out.

• Replace shelves by inserting hooks into metal track and lowering front of shelf

!.ii Metal

Crisper Drawers

Crisper drawers keep produce fresh longer_Wrap produce

tightly De not wash produce before placing in crisper's

Excess moisture could cause produce to spoil prematurely Do not line crispers with paper towels Paper-

towels retain moisture°

Crisper control is located below front shelf trim.. Control adjusts humidity in crisper drawers_ Slide control to high for produce with leaves such as lettuce, spinach or'

cabbage Slide control to lowfor produce with skins such as cauliflower, corn or tomatoes.

Remove shelf and crisper drawers by completing the following steps:

1. Open left crisper.

• For doors hinged on left, open right crisper

CAUTION: Handle tempered glass shelves

carefully to avoid personal injury or property damage Shelves may break suddenly if nicked, scratched, or exposed to sudden temperature change.

2. Remove glass crisper' top by gently pushing up from

underneath_ Tilt one end up and pull out

hook"

Slide out shelves pull forward for easy access to items in back.

3. Remove left crisper by lifting from front while supporting underneath and pulling out..For doors

hinged on left, remove right crisper°

4o Remove support post at recess in bottom center of

Fresh Food section..

5o Remove other crisper by sliding to opposite wall. Lift

from front while supporting underneath and pull out..

6. Replace crispers and shelf by performing steps 2-5 in reverse order°

Temperature Controlled Meat Drawer (some models)

The temperature controlled meat drawer features a drawer inside a sleeve, Freezer air circulates between

drawer and sleeve.,This systems keeps food fresh longer and up to 5°F (3°C) colder than refrigerator temperature

Temperature controlled meat drawer control is located below front shelf trim Control adjusts amount of air circulating around drawer. Slide control to COLD for normal refrigerator temperature and to COLDER for colder temperature,, Ice crystals may form on drawer or food on COLDERsetting, Cold air entering the meat drawer can decrease refrigerator temperature,

Refrigerator control may need to be adjusted to a lower number to compensate for colder air,.

Temperature controlled meat drawer can be moved from the left to the right side of the refrigerator compartment to accomodate different storage needs,To move drawer perform the following steps:

1 Remove drawer by lifting and pulling out Remove

shelf by lifting from front, releasing hooks from metal track, then pulling out.,

Temperature Controlled j_,_!

Meat Drawer installed f.:, I Boot

on left side of \

refrigerator !_ .,:,,:._.,_"..:'_:-4r._

Meat drawer

control ....

Temperature Controlled _

Meat Drawer installed /.._r_-. t

on right side of Plastic _'_

refrigerator cap

2 Remove plastic cap from back wal! of refrigerator

section by placing a knife covered with masking tape

underneath cap and pulling forward

Meat drawer control

Rotate boot 180" to opposite side.

Insert plastic cap in opposite side of Fresh Food section. Confirm cap is snugly in place,, Cold air

may cause food to freeze if cap is not replaced.

Replace shelf by inserting hooks into metal track and lowering the front. Use slots 4 though 6only.

Replace drawer by sliding in. Make sure boot fits snugly over air inlet in back wall

Bottle Rack (some models) Bottle rack provides convenient storage for a large bottle,

eggs, etc._

Dairy Compartment (some models) Dairy compartment provide convenient storage for butter,

cheese, etc

• Hang rack by hooking over side of shelf

Covered Utility Bin (some models) The utility bin has a lid and removable egg tray,,When tray

is removed, bucket will accept standard egg carton, ice, etc,,

• Remove dairy compartment by lifting door, pushing tabs of shelf down on both sides, and pulling out.

• Replace dairy compartments by sliding in until tabs lock into place, then lower door.

Door /

Door Buckets

Door buckets adjust to meet individual storage needs

• Remove door buckets by pushing tabs on both sides of shelves toward center and pulling bucket out

° Replace door buckets by sliding in until tabs lock

into place,

Egg

tray

Utitity bin

Tall Package Retainer (some models) Tall package retainer keeps talt items secure Retainer fits

on front edge of any refrigerator door bucket or door shelf

Adjustable Divider (some models)

Adjustable divider keeps items in place and adjusts to meet individual storage needs Divider fits in any door

bucket or door shelf

Tall package

retainer

Door Shelves

• Remove door shelves by lifting ends and pulling out,

• Replace door shelves by placing shelf on glides and sliding down,

Door shelf

Glide

!_ _!T!_ il i ¸

• j.

Adj

Bottle Holder (some models) Bottle holder keeps items in place and adjusts to meet individual storage needs Bottle holder fits in any door

bucket or door shelf,

ii,-._7

Freezer Features

Frost-Free System

The refrigerator and freezer sections are completely frost-free Defrosting is automatic under normal

conditions,, Refrigerator and freezer sections never have

to be defrosted

Automatic Ice Maker (some models)

• Make sure ice bucket is in place and ice maker arm is down,,

- !!

Ice Service Rack (some models)

Install ice service rack by completing the following steps using a Phillips screwdriver:

1. Loosen screw and washer on freezerside wall.

2. Place ice service rack on washers and slide down..

3.. Tighten screws and washers Move ice service rack by completing the following steps

using a Phillips screwdriver:

1. Remove ice service rack by liftingrack off washers, then pulling out.

2. Remove screws and washers that support ice service rack. Remove plugs from freezer wail opposite ice service rack. Replace plugs with screws and washers, insert plugs in holes remaining from

removal of screws and washers.

3 Replace ice service rack by placing rack on washers

and sliding down until secure..

/ Ice serv ce

....... ! ,z" rack

• After freezer section reaches normal temperature, the ice maker fills with water and begins operating.

Allow 24-48 hours after installation before first harvest of ice Ice maker produces 7 to 9 harvests of

ice in a 24-hour period under ideal conditions,

• After ice is formed, ice maker drops ice cubes into ice storage bucket. During ice production, ice maker arm raises and lowers When ice storage bucket is

full, ice maker arm turns ice maker off:

Note: Discard first 3 harvests of ice so any impurities teft

in the water line after installation are not consumed.

If you wish to stop automatic ice production lift ice maker arm. A definite click is heard when proper position is reached Ice maker' arm will remain in that position until pushed down..

CAUTION: Make sure shelf is secure before /

placing items on shelf to avoid property damage_

]

Wire Shelf

• Remove wire shelf by pulling out., A sharp tug may

be necessary,

• Replace wire shelf by sliding in until back locks in place,,

Wire Basket

Wire basket slides out for easy access to items in back,

Ice Bin (some models) Ice bin sits below the ice service rack on the wire freezer

shelf.

i _

- Remove wire basket by lifting and pulling ouL , Replace wire basket by sliding in,

Wire basket

Care and Cleaning

_kWARNING: Disconnect power to refrigerator before cleaning to avoid electrical shock which can

cause severe personal injuryor death. After cleaning, restore power.

_ CAUTION: Read and follow all manufacturer's cleaning directions to avoid personal injury or property

damage.

General Cleaning

1 Wash surfaces and exterior with 4 tablespoons

baking soda dissolved in 1 quart warm water and a soft, clean cloth.

2 Rinse surfaces and exterior with warm water Dry

surfaces with a soft, clean cloth.

& DO NOT USE the following items:

• abrasive orharsh cleaners, ammonia, chlorine bleach, etc

• concentrated detergents or solvents

• metal scouring pads

These items can scratch, crack, and discolor surfaces.

4 Do not place buckets, shelves, etc., in dishwasher.

Adhesives

1. Remove adhesive residue from refrigeratorsurfaces by rubbing toothpaste into adhesive with fingers until

adhesive loosens

2 Rinse surface with warm water. Dry surface with a

soft, clean cloth°

Door Gaskets

1.. Clean door gaskets every 3 months according to General Cleaning instructions Clean any spills

immediately.

2.. Apply a light film of petroleum jelly to keep gaskets pliable.

Condenser Coils

Clean condenser coil behind toe grille every 3 months to ensure maximum performance of refrigerator: Accumulated dust and lint may cause the following:

• reduced cooling performance

• increased energy usage

• premature part faiture

1o Remove toe grille by holding ends and pulling away

from refrigerator'

2. Clean front surface of condenser coi! with a vacuum

cleaner hose nozzle.

& Replace toe grille by inserting clips in holes and

snapping in.

4. Raise stabilizing legs (some models) by turning counterclockwise.

,_ CAUTION: Protect soft vinyl or other flooring with cardboard, rugsor other protective material to

arc d property damage,

5 Pull refrigerator' away from wall..Run a vacuum

brush across grille on back of refrigerator..

Glass Shelves

CAUTION: Handle tempered glass shelves

carefully to avoid personal injury or property damage. Shelves may break suddenly if nicked, scratched, or

exposed to sudden temperature change.

Remove shelf by lifting front, releasing hooks from metal

track then pulling out. Place shelf on a towel.. Allow shelf to adjust to room temperature before cleaning

Clean crevices by completing the following: I.. Dilute mild detergent and brush solution into crevices

using a plastic bristle brush. Let sit for5 minutes.

2.. Spray warm water'into crevices using faucet spray attachment..

3. Dry shelf thoroughly and replace shelf by inserting hooks into metal track and lowering itfrom the front.

Odor Removal

i.. Remove all food and disconnect power to refrigerator,

2. Clean all interior surfaces including ceiling, floor, and

walls according to General Cleaning instructions

above. Pay special attention to corners, crevices, and

grooves. Include all drawers, shelves, and gaskets.

3. Connect power to refrigerator and returnfood to refrigerator Wash and dry all containers. Wrap foods in tightly sealed container's to prevent further odor:

After 24 hours, check if odor has been eliminated..

Complete steps 4-9 if odor has not been eliminated

4. Place crispers on top shelf of refrigerator section. Pack refrigerator and freezer sections, including

doors, with crumpled sheets of newspaper:

5. Place charcoal briquettes randomly throughout newspaper.

6. Close doors and let stand 24-48 hours.

7. Remove charcoal briquettes and newspapers..

8. Complete steps 2-&

If odor is still not eliminated, contact a Sears Service

Center.

Vacation Tips

Light Bulb Replacement

WARNING: Disconnect power to refrigerator

before replacing light bulb to avoid electrical shock which can cause severe personal injury or death After

replacing light bulb, restore power,

CAUTION: Observe the following to avoid

personal injury or property damage

Allow light bulbs to cool Wear gloves when replacing light bulb.

• Remove light bulb cover by removing W' hex nut screws, RepTace bulb(s) with 40-watt appliance bulb(s).

• Replace light bulb cover by replacing W' hex nut screws,

I/4" hex

nut screws

Complete the following steps for short vacations 1 Remove perishable foods

2o If an ice maker is installed, move ice maker arm to

Offposition (See "Automatic Ice Maker" section page

12)

Complete the following steps for long vacations. 1 Empty refrigerator and freezer sections

2, Unplug refrigerator, 3 Clean refrigerator and door gaskets according to

General Cleaning instructions in "Care and Cleaning" section,.

4, Prop doors open, so air can circulate inside

5. If an ice maker is installed, turn off water supply to refrigerator and move ice maker arm to Off

position, (See "Automatic Ice Maker" section page 12)

Energy Tips

This refrigerator is designed to be one of the most energy

efficient refrigerators available Reduce energy use by

observing the following.

• Operate in normal household temperatures of 55° to

110°F (13° to 43°C) away from heat sources and direct

sunlight.

° Set refrigerator, freezer, and temperature controlled

meat drawer system controls no colder than necessary

• Keep freezer section full.

° Keep door gaskets clean and pliable, Replace gaskets

if worn..

. Keep condenser coils clean

cover

Normal Operating Sounds

This new refrigerator may be replacing a differently designed, tess efficient or smaller refrigerator: Today's refrigerators have new features and are more energy efficient, As a result, certain sounds may be unfamiliar.,

These sounds are normal and will soon become familiar to you, They also indicate refrigelator is operating and

performing as designed

1,, Freezer control clicks when starting or stopping

compressor.

2, Freezer fan air tushes and whirs 3 Sealed system (evaporator and heat exchanger)

refrigerant flow gurgles, pops or sounds like boiling water,

4,, Defrost heater sizzles, hisses or pops,

5 Defrost timer sounds like an electric clock and

snaps in and out of defrost cycle.

6 Condenser fan air rushes and whirs,,

7. Compressor has a high pitched hum or pulsating sound and cycles on and off.

8. Ice cubes from ice maker (some models) drop into ice bucket,

9 Ice maker water valve hookup (some models)

buzzes when ice maker fills with water, This occurs

whether or not refrigerator is connected to water supply If refrigerator is not connected to water supply, stop sound by raising ice maker arm to Off

position,, Ice maker water valve hookup is located behind condenser fan in back of refrigerator,

Note: Foam insulation is very energy efficient and has excellent insulating capabilities. However, foam

insulation is not as sound absorbent as previously used fiberglass insulation,

Before Calling For Service

Problem Solution

Refrigerator does not operate

Refrigerator still will not operate

Food temperature appears too waim ,

Temperature controlled meat drawer ,, temperature is too warm •

Food temperature is too cold •

Refrigerator runs too frequently •

Make sure freezer control is on

Make sure refrigerator is plugged in ff not, firmly plug the cord into a live outlet with proper voltage

Check fuse or circuit breaker, Plug in another item at that walt outlet If outlet does not work, reptace the fuse or reset the circuit

If freezer control is on, light works but 2 fans and compressor is not operating, refrigerator may be in defrost cycle Wait 40 minutes to see if refrigerator restarts

Unplug refrigerator Transfer food to another refrigerator or place dry ice in freezer section to preserve food Call for service

See above sections Allow time for recently added warm food to reach refrigerator or

freezer temperature Adding food warms the refrigerator It can take a few hours for the refrigerator to return to normal temperature

Check gaskets for proper seal Gaskets should seal tightly to cabinet Clean condenser coils See "Condenser Coils" instructions in "Care

and Cleaning" section

Adjust refrigerator and or freezer control. See "Setting Controls" instructions in "Controls" section

Freezer or refrigerator light stays on if light stays on, cal! service

Return air vents behind crisper are blocked restricting airflow Locate return air vent behind crispers and remove any debrisis that blocks

vents or restricts airflow Slide control to colder setting.

Adjust freezer control to colder setting See "Setting Controls" instructions of "Controls" section

Verify temperature controlled meat drawer cap has been moved if drawer has been moved from left to right side of cabinet See "Temperature Controlled Meat Drawer" section

Clean condenser coils,, See "Condenser Coils" instructions in "Care and Cleaning section,

Adjust refrigerator control See "Setting Controls" instructions in "Controls" section

Adjust freezer control to warmer setting., See "Setting Controls"

instructions in "Controls" section Allow several hours for temperature to adjust,

Verify plastic cap is in place opposite temperature controlled meat

drawer, See "Temperature Controlled Meat Drawer" section,,

It may be normal to maintain constant temperature Doors have been opened frequently or for an extended period of time,

When the door is opened warm humid air is allowed into the

refrigerator., The more the door is opened the more warm air the refrigerator must cool

Allow time for recently added warm food to reach refrigerator or

freezer temperature,. It can take a few hours for the refrigerator to return to normal temperature

Clean condenser coils See "Condenser Coils" instructions in "Care and Cleaning" section

Adjust freezer control See "Setting Controls" instructions in "Controls" section

Check gaskets for proper seal Gaskets should seal tightly to cabinet,

Freezer light stays on If light stays on, calf service Make sure refrigerator is level, See "Leveling Refrigerator" section of

installation Instructions

Problem Solution

Water droplets form on inside of • It is normal during high humidily periods or if doors have been opened

refrigerator' frequently,,

• Wrap food tightly and wipe off damp containers prior to storing in the refrigerator to avoid moisture accumulation.

water droplets form On 0uisicle Of , Check do0r"seals fo; proper seal Gaskets shoul'd'seal tightly io....................................

refrigerator cabinet

• It is normal during high humidity periods or if doors have been opened

frequently

Temperature controlled meat drawer ° Check for a package that may prevent drawer from closing properly or crisper drawer does not close ° Confirm drawer is in proper position

freely (some models) ° Clean drawer channels with warm, soapy water Rinse and dry

thoroughly.

- Apply a thin layer of petroleum jelly to drawer channels

• Confirm refrigerator is level.

Refrigerator has an Od0rl • See "Odor Removal" instructions in "Care and Cleaning" section. Refrigerator makes unfamiliar sounds • It may be normal. See "Normal Operating Sounds" section.

or seems too loud. Ice cubes have an odor ,, See "Odor Removal" instructions in "Care and Cleaning" section

• Ice maker was recently installed, Discard first few batches of ice to avoid discolored or off41avored ice

• Food has not been wrapped tightly in either refrigerator or freezer compartment Rewrap foods since odors may migrate to the ice if food

is not wrapped properly

• Discard ice and clean ice bucket or trays more frequently Ice cubes are porous and absorb odors easily

,_ Water supply contains minerals such as sulfur, In some situations a

filter may need to be installed to eliminate taste and odor prQb!ems:

Ice cubes stick together or "shrink"

Ice maker is not producing ice,

Ice maker is not producing enough ice.

Ice forms in inte'i'tube"io"ice"maker.

• Empty ice cube bucket or trays more frequently° If used infrequently, ice cubes me--ether or shrink.

• Water pressure may be to low or high Ice maker requires a water pressure of 20q20 psi to function properly

• Confirm ice maker arm is down. See "Automatic Ice Maker" section.

• Confirm household water supply is reaching water valve Make sure the water vaive shut off is fully turned on

o C0nfi_m ice maker wiring harness iS inserted comp!ete!y in proper

holes,

• Check for kinks in copper or plastic tubing. Remove kinks or replace tubing.

• Check electrical connections to water valve coil and connector block on refrigerator cabinet..

,, If a water filter has been installed on the water line outside the

refrigerator, check the filter for clogs or improper installation of the filter.

• Ice maker has just recently been installed or a large amount of ice has

just been used, Wait 24 hours for ice production to begin and for ice

maker to restock after emptied

• Confirm household water supply is reaching water valve_ Make sure the water valve shut off is fully turned on.

° Piercing type or _lt_"saddle valve was used for hookup. Both reduce

water flow and may become clogged with time. Replace these valves with correct type of saddle valve requiring '/4"hole to be drilled in water

supply pipe prior to valve attachment

,, Check for kinks in copper or plastic tubing. Remove kinks or replace

tubing

• Confirm freezer section is operating at proper temperature. Freezer .mustbe cold enough to produce ice. See 'Setting..Controls" section.

,m Check water pressure. Low water pressure causes valves to leak.

Warranty

Full One Year Warranty on Refrigerator

For one year from the date of purchase, when this refrigerator isoperated and maintained according to instructions attached to or furnished with it, Sears will repair it, free of charge, if defective in material or workmanship.

Ful! Five Year Warranty on Sealed Refrigeration System

For five years from the date of purchase, when this refrigerator is operated and maintained according to instructions attached to or furnished with it, Sears will repair the sealed system (consisting of refrigerator, connecting tubing and compressor motor) free of charge, if defective in materia) or workmanship.

The above warranty coverage applies only to refrigerators which are used for storage of food for private household purposes

Warranty Service isavailable by contacting 1_800-4-MY-HOM E (1-800-469-4663). This warranty applies only while this product is in use in the United States.

This Warranty gives you specific legal rights, and you may also have other rights, which var.y from state to state.

Sears, Roebuck and Co, Dept 817WA, Hoffman Estates, IL 60179

+ 43 hidden pages