Kenmore 59672389411, 59672389410, 59672383413, 59672383411, 59672383410 Owner’s Manual

Use & Care Guide
Manual de uso y cuidado

Guide d_utilisation et d_entretien

English / Espafiol / Fran_ais

Model/Modelo/Mod_le: 596.7238 _

I(enmore

,,:,:::color numbe_, n@nero de colo_, le num@o de M couleu_

P/N W10675342A
Sears Brands Management Corporation

Hoffman Estates, IL, U.S.A. 60179
www.kenmore.com
www.sears.com

Sears Canada Inc.
Toronto, Ontario, Canada M5B 2C3

www.sears.ca

@

TABLEOF CONTENTS

PROTECTION AGREEMENTS ................................................... 2

WARRANTY ............................................................................. 3

REFRIGERATOR SAFETY......................................................... 4

Proper Disposal of Your Old Refrigerator ....................................5

INSTALLATION INSTRUCTIONS .............................................. 5

Unpack the Refrigerator ..................................................................5

Remove and Replace Refrigerator Doors .....................................6

Remove and Replace Drawer Fronts .............................................9

Location Requirements .....................................................................11

Electrical Requirements ...................................................................11

Water Supply Requirements .........................................................12

Connect the Water Supply ............................................................12

Handle Installation and Removal .................................................14

Refrigerator Leveling, Door Closing and Alignment ................. 15

FILTERS AND ACCESSORIES .................................................. 16

Water Filtration System .................................................................16

Install Air Filter .................................................................................17

Accessories ........................................................................................18

REFRIGERATOR USE............................................................... 18

Opening and Closing Doors.......................................................... 18

Using the Controls........................................................................... 18

Refrigerator Features.......................................................................21

Water and Ice Dispensers.............................................................22

Ice Maker and Ice Storage Bin.....................................................2.5

REFRIGERATOR CARE ........................................................... 26

Cleaning ............................................................................................26

Lights................................................................................................. 27

Power Interruptions ........................................................................27

Vacation and Moving Care ......................................................... 27

PROBLEM SOLVER ................................................................. 28

WATER FILTER CERTIFICATIONS .......................................... 34

PERFORMANCE DATA SHEET ............................................... 35

SERVICE NUMBERS ............................................. BACK COVER

JNDICE ................................................................................... 36

TABLE DESMATIF:RES............................................................ 72

PROTECTION AGREEMENTS

Master Protection Agreements

Congratulations on making a smart purchase. Your new
Kenmore ® product is designed and manufactured for years of
dependable operation. But like all products, it may require

preventive maintenance or repair from time to time. That's when
having a Master Protection Agreement can save you money and

aggravation.
The Master Protection Agreement also helps extend the life of

your new product. Here's what the Agreement* includes:
1/Parts and labor needed to help keep products operating

properly under normal use, not just defects. Our coverage
goes well beyond the product warranty. No deductibles, no

functional failure excluded from coverage--real protection.

1/Expert service by a force of more than 10,000 authorized

Sears service technicians, which means someone you can
trust will be working on your product.

1/ Unlimited service calls and nationwide service, as often as

you want us, whenever you want us.

1/"No-lemon" guarantee- replacement of your covered

product if four or more product failures occur within twelve
months.

1/Product replacement if your covered product can't be fixed.
1/Annual Preventive Maintenance Check at your request - no

extra charge.

I/' Fast help by phone - we call it Rapid Resolution - phone

support from a Sears representative on all products. Think of
us as a "talking owner's manual."

Ii' Power surge protection against electrical damage due to

power fluctuations.

I/$250 Food Loss Protection annually for any food spoilage

that is the result of mechanical failure of any covered
refrigerator or freezer.

I/Rental reimbursement if repair of your covered product takes

longer than promised.

1/25% discount off the regular price of any non-covered

repair service and related installed parts.

Once you purchase the Agreement, a simple phone call is all
that it takes for you to schedule service. You can call anytime

day or night, or schedule a service appointment online.
The Master Protection Agreement is a risk free purchase. If you

cancel for any reason during the product warranty period, we
will provide a full refund. Or, a prorated refund anytime after

the product warranty period expires. Purchase your Master
Protection Agreement today!

Some limitations and exclusions apply. For prices and
additional information in the U.S.A. call 1-800-827-6655.

*Coverage in Canada varies on some items. For full details call

Sears Canada at 1-800-361-6665.

Sears Installation Service

For Sears professional installation of home appliances, garage
door openers, water heaters, and other major home items, in the

U.S.A. or Canada call 1-800-4-MY-HOME ®.

2

KENMORE APPLIANCE WARRANTY

ONE YEAR LIMITED WARRANTY

When installed, operated and maintained according to all
supplied instructions, if this appliance fails due to a defect in

material and workmanship within one year from the date of
purchase, call 1-800-4-MY-HOME _ (1-800-469-4663) to

arrange for free repair.
If this appliance is ever used for other than private family

purposes, this warranty applies for only 90 days from the date
of purchase.

Thiswarranty covers only defects in material and
workmanship. Sears will NOT pay for.

1. Expendable items that can wear out from normal use,

including but not limited to filters, belts, incandescent light
bulbs, and bags.

2. A service technician to instruct the user in correct product

installation, operation or maintenance.

3. A service technician to clean or maintain this product.

4. Damage to or failure of this product if it is not installed,

operated or maintained according to all instructions
supplied with the product.

5. Damage to or failure of this product resulting from accident,

abuse, misuse or use for other than its intended purpose.

6. Damage to or failure of this product caused by the use of

detergents, cleaners, chemicals or utensils other than those
recommended in all instructions supplied with the product.

7. Damage to or failure of parts or systems resulting from

unauthorized modifications made to this product.

Disclaimer of implied warranties; limitation of remedies
Customer's sole and exclusive remedy under this limited

warranty shall be product repair as provided herein. Implied
warranties, including warranties of merchantability or fitness for

a particular purpose, are limited to one year or the shortest
period allowed by law. Sears shall not be liable for incidental or

consequential damages. Some states and provinces do not
allow the exclusion or limitation of incidental or consequential

damages, or limitations on the duration of implied warranties of
merchantability or fitness, so these exclusions or limitations may

not apply to you.
This warranty applies only while this appliance is used in the

United States or Canada _.
This warranty gives you specific legal rights, and you may also

have other rights which vary from state to state.

In Canada, in-home repair service is not available in all

areas, nor will this warranty cover user or servicer travel and
transportation expenses if this product is located in a remote
area (as defined by Sears Canada Inc.) where an authorized

servicer is not available.

Sears Brands Management Corporation

Hoffman Estates, IL 60179

Sears Canada Inc.

Toronto, Ontario, Canada M5B 2C3

PRODUCT RECORD

Record your complete model number, serial number, and
purchase date. You can find this information on the model and

serial number label located on the product.
Have this information available to help you obtain assistance or

service more quickly whenever you contact Sears concerning
your appliance.

Model number

Serial number

Purchase date

Save these instructions and your sales receipt for future
reference.

REFRIGERATORSAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow
instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of fire, electric shock, or injury when using your refrigerator, follow these basic precautions:

[] Plug into a grounded 3 prong outlet.
[] Do not remove ground prong.

[] Do not use an adapter.
[] Do not use an extension cord.

[] Disconnect power before servicing.
[] Replace all parts and panels before operating.

[] Remove doors from your old refrigerator.

SAVE THESE INSTRUCTIONS

[] Use nonflammable cleaner.
[] Keep flammable materials and vapors, such as gasoline,

away from refrigerator.

[] Use two or more people to move and install refrigerator.
[] Disconnect power before installing ice maker (on ice maker

kit ready models only).

[] Use a sturdy glass when dispensing ice (on some models).
[] Do not hit the refrigerator glass doors (on some models).

State of California Proposition 65 Warnings:
WARNING: This product contains one or more chemicals known to the State of California to cause cancer.

WARNING: This product contains one or more chemicals known to the State of California to cause birth defects or other
reproductive harm.

4

ProperDisposalof YourOld Refrigerator

Suffocation Hazard

Remove doors from your old refrigerator.
Failure to do so can result in death or brain damage.

IMPORTANT: Child entrapment and suffocation are not
problems of the past. Junked or abandoned refrigerators are

still dangerous - even if they will sit for "just a few days." If you
are getting rid of your old refrigerator, please follow these

instructions to help prevent accidents.

Before You Throw Away Your Old Refrigerator or Freezer..

• Take off the doors.

• Leave the shelves in place so that children may not easily
climb inside.

\

important information to know about disposal of
refrigerants:

Dispose of refrigerator in accordance with Federal and Local
regulations. Refrigerants must be evacuated by a licensed,
EPA certified refrigerant technician in accordance with
established procedures.

INSTALLATION INSTRUCTIONS

Excessive Weight Hazard

Use two or more people to move and install
refrigerator.

Failure to do so can result in back or other injury.

Remove the Packaging

Remove tape and glue residue from surfaces before turning
on the refrigerator. Rub a small amount of liquid dish soap
over the adhesive with your fingers. Wipe with warm water

and dry.
Do not use sharp instruments, rubbing alcohol, flammable

fluids, or abrasive cleaners to remove tape or glue. These
products can damage the surface of your refrigerator. For

more information, see "Refrigerator Safety."

• Shelves, bins, door shelf rails, and other feature parts may
be packaged in the Interior FeaturePak. Follow the
instructions contained in the package for proper assembly.

• Dispose of/recycle all packaging materials.

When Moving Your Refrigerator:
Your refrigerator is heavy. When moving the refrigerator for

cleaning or service, be sure to cover the floor with
cardboard or hardboard to avoid floor damage. Always pull
the refrigerator straight out when moving it. Do not wiggle or
"walk" the refrigerator when trying to move it, as floor
damage could occur.

Clean Before Using

After you remove all of the packaging materials, clean the
inside of your refrigerator before using it. See the cleaning

instructions in "Refrigerator Care."

important information to know about glass shelves

and covers:

Do not clean glass shelves or covers with warm water when
they are cold. Shelves and covers may break if exposed to

sudden temperature changes or impact, such as bumping.
Tempered glass is designed to shatter into many small,

pebble-size pieces. This is normal. Glass shelves and covers
are heavy. Use both hands when removing them to avoid
dropping.

NOTE" Measure the width of your door opening, to see whether or not you need to remove the refrigerator doors to move the
refrigerator into your home. If door removal is necessary, see the following instructions.

IMPORTANT. If the refrigerator was previously installed and you are moving it out of the home, before you begin, turn the
refrigerator control OFR Unplug the refrigerator or disconnect power. Remove food and adjustable door or utility bins from doors.

Gather the required tools and read all instructions before removing doors.
TOOLS NEEDED; 3/_6" hex key wrench and a #2 Phillips screwdriver

%_¢ Electrical Shock Hazard

Disconnect power before removing doors.
Failure to do so can result in death or electrical shock.

Style 1 - Water Dispenser

Tubing Connection

\

\

\

\

\

\

\

Style 2 - Water Dispenser

Tubing Connection

\

\

\

\

Door Removal

A

A. Outer Ring

Wiring Plug

A. Outer Ring

I

I

I

I

I

I

I

I

I @

!

I

I

!

A. _8" Internal Hex-Head Screws
B. Hinge Cover Screw

C. Top Hinge Cover
D. Top Hinge

@

Top Left Hinge

A B

c

A. _6" Internal Hex-Head Screws
B. Ground Wire (Do Not Remove)

C. Do Not Remove Screws

6

@

@

RemoveRight-Hand Refrigerator Door Remove Left-Hand Refrigerator Door

IMPORTANT= The tubing and wiring for the water dispenser run
through the left-hand door hinge, so they must be disconnected

before removing the door.

1. Using a Phillips screwdriver, remove the cover from the top
hinge.

Electrical Shock Hazard

Disconnect power before removing doors.
Failure to do so can result in death or electrical shock.

1. Unplug refrigerator or disconnect power.

2. Keep the refrigerator doors closed until you are ready to lift
them free from the cabinet.

NOTE= Provide additional support for the refrigerator door
while the hinges are being removed. Do not depend on the

door gasket magnets to hold the door in place while you are
working.

.

Using a Phillips screwdriver, remove the cover from the Top
Hinge.

4.

Using the 3/16"hex key wrench, remove the two internal hex
head screws from the top hinge, and set aside.

NOTE: Do not remove the two Iocator screws. These screws
will help you align the hinge when you replace the door.

A ....................... '_

B _ ..................

A. Top hinge cover screw B. Top hinge cover

2.

Disconnect the water dispenser tubing located on top of the

t

i
i

o

door hinge.
Style 1 - Press the outer ring against the face of the fitting

and gently pull the dispenser tubing free.
NOTE: The water dispenser tubing remains attached to the

left-hand refrigerator door.

D

A. Top hinge cover screw

B. Top hinge cover

C. 3_6" /nterna/ hex head screws

D. Top hinge

ExcessiveWeight Hazard

Usetwo or more people to lift the refrigerator door.
Failureto do so can resultin back or other injury.

5. Lift the refrigerator door from the bottom hinge pin. The top
hinge will come away with the door.

\

A. Outer ring

B. Face of fitting

Style 2 - Firmly pull up on the clasp. Then, pull the tubing out
of the fitting.

NOTE: The water dispenser tubing remains attached to the
left-hand refrigerator door.

\

.

Disconnect the wiring plug located on top of the door hinge.

• Grasp each side of the wiring plug. With your left

thumb, press down to release the catch and pull the
sections of the plug apart.

NOTE: Do not remove the green, ground wire. It should
remain attached to the door hinge.

4.

Using the 3/16" hex key wrench, remove the two internal hex
head screws from the top hinge, and set aside.

NOTES:

.

Lift the refrigerator door from the bottom hinge pin. The top
hinge will come away with the door.

NOTE: It may not be necessary to remove the bottom hinges
and brake feet assemblies to move the refrigerator through

a doorway.

• Only if necessary, use a driver with a #2 square bit tip to
remove the bottom hinges and a 3/8" nut driver to

remove the brake feet screws.

Replace Right-Hand Refrigerator Door

1. Set the right-hand door onto the bottom hinge pin.

2. Insert the top hinge pin into the open hole in the top of the
refrigerator door.

3. Using the two 3A6" internal hex head screws, fasten the hinge
to the cabinet. Do not tighten the screws completely.

Replace Left-Hand Refrigerator Door

IMPORTANT: Do not intertwine the water tubing and wiring
bundles when reconnecting them.

1. Set the left-hand door onto the bottom hinge pin.

2. Using the two 3/_6"internal hex head screws, fasten the hinge
to the cabinet. Do not tighten the screws completely.

3. Reconnect the water dispenser tubing.

Style 1 - Insert the tubing into the fitting until it stops and the

outer ring is touching the face of fitting.
Style 2 - Insert the tubing firmly into the fitting until it stops.

Close the clasp around the tubing. The clasp snaps into
place between the fitting and the collar.

4. Reconnect the electrical wiring.

• Push together the two sections of the wiring plug.

• Provide additional support for the refrigerator door
while the hinges are being removed. Do not depend on

the door gasket magnets to hold the door in place while
you are working.

• Do not remove the two Iocator screws. These screws will
help you align the hinge when you replace the door.

A B

C

A. 3_6" /nterna/ hex head screws

B. Ground wire [do not remove]

C Locator screws (do not

remove]

Final Steps

1.

Completely tighten the four internal hex head screws (two
on the right-hand door hinge and two on the left-hand door

hinge).

2.

Replace both top hinge covers.

Depending on the width of your door opening, it may be 3.
necessary to remove the drawer fronts to move the refrigerator

into your home.

IMPORTANT:

If the refrigerator was previously installed and you are

moving it out of the home, before you begin, turn the
refrigerator control OFF, and unplug the refrigerator or

disconnect power. Remove food from the drawers.

• Two people may be required to remove and replace the
drawer fronts.

Tools Needed: 1¼,,Hex head nut driver, Flat-blade screwdriver

Refrigerated Drawer

Disconnect Wiring
NOTES:

The exterior refrigerator drawer front is connected to the
temperature control. Before removing the drawer front, the

wires must be disconnected from the temperature control.
The gray cable visible behind and under the pantry drawer

at the right side contains wiring for the pantry control and
moves with the drawer as it is pulled out. There is no need to

disconnect this cable.

.

Open the drawer to its full extension, and remove the large
interior bin.

2.

Locate the wiring cover on the backside of the drawer front.
Press tab on the cover to release the snaps, and pull off

cover to reveal the wiring connection.

On one side of the wiring connector, insert the screwdriver
blade between the connector tab and the connector to

release. Repeat for the opposite side. Pull the wiring
connector apart.

Remove Drawer Front

1. Using a 1/4"hex head nut driver, remove the two bottom

screws (one on each side) attaching the drawer front to the
drawer glides.

2. Using 1/4" hex head nut driver, loosen the two top screws
(one on each side) attaching the drawer front to the drawer

glides.
NOTE: Loosen the screws three to four turns. Keep the

screws in the drawer front.

3. Lift the drawer front up and off the drawer glide brackets.

A. Press tab

B. _Viring connection cover

A. Loosen top screws

B. Drawer glide bracket

4. Slide the drawer glides back into the refrigerator.

C. Remove bottom screws

Replace Drawer Front

1. Pull out the drawer glides until they are fully extended.

2. Lower the loosened screws in the top of the drawer front into
the upper notches in the drawer glides.

NOTE: It helps if one person holds the drawer glides steady
while another person aligns the drawer front and insertsthe

screws into the notches.

3. Align the holes in the bottom of the drawer front with the
holes in the bottom of the drawer glides and fasten with the

screws removed earlier.

4. Tighten the two top screws.

Reconnect Wiring

1. Align the two ends of the wiring connector and push them
together until you hear a "click" sound and feel the tabs
snap into place on the connector.

2. Gently pull on the wiring connection to ensure the wiring
connection iscompletely seated. Replace the wiring cover.

NOTE: The wiring connection must be complete for the
drawer temperature control to operate.

3. Lift up on the drawer front to release the plastic studs from
the drawer glide bracket slots.

A. Drawer glide bracket slots

4. Slide the drawer glides back into the freezer.

Replace Drawer Front

1. Pull out the freezer drawer glides to their full extension.

2. Holding the drawer front by its sides, align the two plastic
studs, located at the bottom, inside the drawer front, with

the drawer glide bracket slots.
NOTE: It helps if one person holds the drawer glides steady

while another person aligns the drawer front and insertsthe
studs into the slots.

3. Replace the interior bin.

Freezer Drawer

Remove Drawer Front

1. Open the freezer drawer to its full extension.

2. Loosen the two top screws that fasten the drawer front to the
drawer glides. The two screws (one on the left-hand side

and one on the right-hand side) are located inside the
drawer front.

Al..................Ill............

B J_J'_JY'

A. Drawer front screw

B. Drawer front plastic stud

3. Replace and tighten the two screws at the top of the drawer
front (one on the left-hand side and one on the right-hand

side).

10

RnalSteps

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.

Do not use an extension cord.
Failure to follow these instructions can result in death,

fire, or electrical shock.

1. Plug into a grounded 3 prong outlet.

2. Reset the controls. See "Using the Control(s)" and

"Temperature Controlled Exterior Drawer."

3. Return all removable parts and the food to the drawers.

NOTE= This refrigerator is intended for use in a location where
the temperature ranges from a minimum of 55°F (13°C) to a

maximum of 110°F (43°C). The preferred room temperature
range for optimum performance, which reduces electricity

usage and provides superior cooling, is between 60°F (15°C)
and 90°F (32°C). It is recommended that you do not install the

refrigerator near a heat source, such as an oven or radiator.

/

/

1/2"(1.25 cm)

11

3¾" (9.5cm)

/

\

Explosion Hazard

Keep flammable materials and vapors, such as
gasoline, away from refrigerator.

Failure to do so can result in death, e×plosion, or fire.

IMPORTANT= This refrigerator is designed for indoor, household
use only.

Toensure proper ventilation for your refrigerator, allow for a 1/2"
(1.25 cm) of space on each side and at the top. Allow for a 1"

(2.54 cm) space behind the refrigerator. If your refrigerator has
an ice maker, allow extra space at the back for the water line
connections. When installing your refrigerator next to a fixed

wall, leave a 33/4'' (9.5 cm) minimum space between the
refrigerator and wall to allow the door to swing open.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.
Do not remove ground prong.

Do not use an adapter.
Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

Before you move your refrigerator into its final location, it is
important to make sure you have the proper electrical

connection.
Recommended Grounding Method

A 115 volt, 60 Hz, AC only 15- or 20-amp fused, grounded
electrical supply is required. It is recommended that a separate

circuit serving only your refrigerator be provided. Use an outlet
that cannot be turned off by a switch. Do not use an

extension cord.

NOTE= Before performing any type of installation, cleaning, or
removing a light bulb, turn Cooling OFF, and then disconnect

the refrigerator from the electrical source. When you have
finished, reconnect the refrigerator to the electrical source and

turn Cooling ON. See "Using the Control(s)."

11

W_c_e_' Su_;;_p_y_ F_equi_e_}e_s_'s

A cold water supply with water pressure between 35 and
120 psi (241 and 827 kPa) is required to operate the water

dispenser and ice maker. If you have questions about your water
pressure, call a licensed, qualified plumber.

NOTE: If the water pressure is less than what is required, the
flow of water from the water dispenser could decrease or ice
cubes could be hollow or irregular shaped.

Reverse Osmosis Water Supply
IMPORTANT: The pressure of the water supply coming out of a
reverse osmosis system going to the water inlet valve of the
refrigerator needs to be between 35 and 120 psi (241 and

827 kPa).
If a reverse osmosis water filtration system is connected to your

cold water supply, the water pressure to the reverse osmosis
system needs to be a minimum of 40 to 60 psi (276 to 414 kPa).

• Check to see whether the sediment filter in the reverse
osmosis system is blocked. Replace the filter if necessary.

Allow the storage tank on the reverse osmosis system to refill
after heavy use. The tank capacity could be too small to

keep up with the requirements of the refrigerator.
NOTE: Faucet mounted reverse osmosis systems are not

recommended.

TOOLS NEEDED;

Gather the required tools and parts before starting installation.

• Flat-blade screwdriver

• 7/%,,and 1/2" open-end wrenches or two adjustable wrenches

• 1/4"nut driver
NOTE: Do not use a piercing-type or 3/_6"(4.76 mm) saddle

valve which reduces water flow and clogs easier.

Connect to Water Line

IMPORTANT: If you turn the refrigerator on before the water is
connected, turn the ice maker OFF.

1. Unplug refrigerator or disconnect power.

2. Turn OFF main water supply. Turn ON nearest faucet long
enough to clear line of water.

3. Use a quarter-turn shutoff valve or the equivalent, served by
a 1/2" household supply line.

NOTE: To allow sufficient water flow to the refrigerator, a
minimum 1/2"size household supply line is recommended.

If your refrigerator has a water filter, it may further reduce
the water pressure when used in conjunction with a reverse
osmosis system. Remove the water filter. See "Water

Filtration System."

If you have questions about your water pressure, call a licensed,
qualified plumber.

Co he W, :4e Suppy

Read all directions before you begin.
IMPORTANT:

• Plumbing shall be installed in accordance with the
International Plumbing Code and any local codes and

ordinances.
The gray water tubing on the back of the refrigerator (which

is used to connect to the household water line) is a PEX
(cross-linked polyethylene) tube. Copper and PEX tubing

connections from the household water line to the refrigerator
are acceptable, and will help avoid off-taste or odor in your

ice or water. Check for leaks.

If PEX tubing is used instead of copper, we recommend the

following part numbers:
W10505928RP (7 ft [2.14 m] jacketed PEX),

8212547RP (5 ft [1.52 m] PEX),or
W10267701RP (25 ft [7.62 m] PEX).

Install tubing only in areas where temperatures will remain

above freezing.

I/ I

A
B

C

A. Sleeve

B. Nut

4.

Now you are ready to connect the copper tubing to the

C. Copper tubing (to refrigerator)
D. Househo/d supp/y /ine ( 7/2"

minimum)

shutoff valve. Use 1/4"(6.35 mm) OD soft copper tubing to
connect the shutoff valve and the refrigerator.

• Ensure that you have the proper length needed for the
job. Be sure both ends of the copper tubing are cut
square.

• Slip compression sleeve and compression nut onto
copper tubing as shown. Insert end of tubing into outlet

end squarely as far as it will go. Screw compression nut
onto outlet end with adjustable wrench. Do not

overtighten.

A. Compression s/eeve

B. Compression nut

C. Copper tubing

12

.

Place the free end of the tubing into a container or sink, and
turn on main water supply to flush out tubing until water is

clear. Turn off shutoff valve on the water pipe.
NOTE: Always drain the water line before making the final

connection to the inlet of the water valve, to avoid possible
water valve malfunction.

6.

Bend the copper tubing to meet the water line inlet, which is
located on the back of the refrigerator cabinet as shown.
Leave a coil of copper tubing to allow the refrigerator to

be pulled out of the cabinet or away from the wall for
service.

.

Thread the nut onto the end of the tubing. Tighten the nut by
hand. Then tighten it with a wrench two more turns. Do not

overtighten.
NOTE: To avoid rattling, be sure the copper tubing does not

touch the cabinet's side wall or other parts inside the
cabinet.

Connect to Refrigerator

Follow the connection instructions specific to your model.

Style I

1. Remove plastic cap from water valve inlet port. Attach the
copper tube to the valve inlet using a compression nut and
sleeve as shown. Tighten the compression nut. Do not

overtighten. Confirm copper tubing is secure by pulling on
copper tubing.

2. Create a service loop with the copper tubing. Avoid kinks
when coiling the copper tubing. Secure copper tubing to

refrigerator cabinet with a "P" clamp.

c

D

A B C D

A. Household water line C. Ferrule {purchased]

B. Nut (purchased) D. Refrigerator water tubing

4.

Install the water supply tube clamp around the water supply

line to reduce strain on the coupling.

5.

Turn shutoff valve ON.

6.

Check for leaks. Tighten any connections (including
connections at the valve) or nuts that leak.

7.

On some models, the ice maker is equipped with a built-in
water strainer. If your water conditions require a second
water strainer, install it in the 1/4" (6.35 mm) water line at

either tube connection. Obtain a water strainer from your
appliance dealer.

Complete the Installation

A. Copper tubing

B. "P" clamp

.

Turn on water supply to refrigerator and check for leaks.

C. Compression nut
D. Compression sleeve

Correct any leaks.

Style 2
I. Unplug refrigerator or disconnect power.

2. Remove and discard the short, black plastic part from the
end of the water line inlet.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.

Do not use an extension cord.
Failure to follow these instructions can result in death,

fire, or electrical shock.

1. Plug into a grounded 3 prong outlet.

2. Flush the water system. See "Water and Ice Dispensers."

NOTE: Allow 24 hours to produce the first batch of ice. Discard
the first three batches of ice produced. Allow 3 days to

completely fill the ice storage bin.

13

Parts Included: Refrigerator door handles (2), Refrigerator
drawer handle (1), Freezer drawer handle (1), 1/8"hex key, spare
setscrew(s)

Install Handles

IMPORTANT." When the screws feel tight, tighten them an
additional quarter-turn. The handle is not properly installed
without this extra tightening.

8°

Repeat steps 2 through 7 to install the other handle onto the
adjacent refrigerator door.

Refrigerator Doors

NOTE: Handle mounting setscrewsare preinstalled inside the
handle.

1. Remove the handles from the packaging inside the
refrigerator, and place them on a soft surface.

2. Open a refrigerator compartment door. On the closed door,
place a handle onto the shoulder screws so that the

setscrews are facing the adjacent door.

A

_B

I

A. Shoulder screws

B. Setscrews inside the handle

Refrigerator and Freezer Drawers

1. With the drawer closed, place the handle onto the shoulder
screws so that the setscrews are facing down toward the

floor.

A

B

A. Shoulder screw

B. Setscrews inside the handle

2. Firmly push the handle toward the drawer until the handle
base is flush against the drawer.

3. Insert the short end of the hex key into the left-hand hole
and slightly rotate the hex key until it is engaged in the

setscrew.

3° Firmly push the handle toward the door until the handle

base is flush against the door.

4. While holding the handle, insert the short end of the hex key
into the upper hole and slightly rotate the hex key until it is

engaged in the setscrew.

5. Using a clockwise motion tighten the setscrew just until it
begins to contact the shoulder screw. Do not fully tighten.

6. Repeat steps 4 and 5 to fasten the lower setscrew.

7. Once both setscrews have been partially tightened as
instructed in the previous steps, fully tighten both setscrews.

4°

Using a left to right motion tighten the setscrew a quarter-
turn at a time just until it begins to contact the shoulder

screw. Do not fully tighten.

°

Repeat steps 11and 12 to fasten the right-hand setscrew to
the shoulder screw.

6.

Once both setscrews have been partially tightened as
instructed in the previous steps, fully tighten both setscrews.

IMPORTANT: When the screws feel tight, tighten them an
additional quarter-turn. The handle is not properly installed

without this extra tightening.

7. Save the hex key and all instructions.

14

Remove the Handles

1.

While holding the handle, insert the short end of the hex key
into a setscrew hole and slightly rotate the hex key until it is

engaged in the setscrew.

2.

Using a right to left motion loosen the setscrew a quarter-
turn at a time.

3.

Repeat steps 1 and 2 for the other setscrew. Slowly pull the
handle away from the door or drawer.

4.

If necessary, use a Phillips screwdriver to remove the

shoulder screws from the door.

Style 1

A. Brake foot

B. Front roller

The base grille covers the adjustable brake feet and roller
assemblies located at the bottom of the refrigerator below the

freezer drawer. Before making any adjustments, remove the
base grille and move the refrigerator to its final location.

Tools Needed: 1/_" hex nut driver

Tools Provided: 1/8"hex key wrench

1. Remove the base grille. Using both hands, grasp the grille
firmly and pull it toward you. Open the freezer drawer to

access the brake feet.
NOTE: To allow the refrigerator to roll easier, raise the

brake feet by turning them counterclockwise. The front
rollers will be touching the floor.

2.

Move the refrigerator to its final location.

3.

Using the 1/4"hex nut driver, lower the brake feet. Turn them
clockwise, until the rollers are off the floor and both brake

feet are snug against the floor. This keeps the refrigerator
from rolling forward when opening the refrigerator doors or

freezer drawer.
IMPORTANT: If you need to make further adjustments

involving the brake feet, you must turn both brake feet the
same amount to keep the refrigerator level.

4.

Make sure the doors close easily. If you are satisfied with the
door opening and closing, skip the next section and go to

"Align the Doors." If, however, the doors do not close easily
or the doors pop open, adjust the tilt.

ToAdjust the Cabinet Tilt:

• Open the freezer drawer. Use a 1/4"hex nut driver to turn

both brake feet clockwise the same amount. This will
raise the front of the refrigerator. It may take several

turns to allow the doors to close easier.
NOTE: Having someone push against the top of the

refrigerator takes some weight off the brake feet. This
makes it easier to turn them.

Style 2

\

ii

\

J

,4

A. Brake foot

°

Make sure the doors are even at the top and that the space
between the bottom of the refrigerator doors and the top of

the freezer drawer is even. If necessary, align the doors.
To Align the Doors:

Keeping both refrigerator doors closed, pull out the
refrigerated drawer. Locate the bottom hinge pin of the

right-hand refrigerator door. The alignment screw is

inside the bottom hinge pin.

A. Bottom hinge pin

B. Turn to the right to raise.

C. Turn to the left to lower.
D. l_" Hex key wrench

15

• Insert the short end of the 1/8"hex key wrench (packed

with the Door Handle Installation Instructions) into the
bottom hinge pin until it is fully engaged in the

alignment screw.
To raise the door, turn the hex key to the right.

To lower the door, turn the hex key to the left.

• Continue to turn the alignment screw until the doors are

aligned.

6. Make sure the refrigerator is steady. If the refrigerator
seems unsteady or rolls forward when a door or drawer is

pulled open, adjust the brake feet.
To Steady the Refrigerator..

• Open the freezer drawer. Using a 1/4" hex driver, turn

both brake feet clockwise the same amount until the
brake feet are snug against the floor. Check again. If not

satisfied, continue to adjust the brake feet by half turns
of the screw until the refrigerator does not roll forward

when the drawer is opened.
NOTE. Having someone push against the top of the

refrigerator takes some weight off the brake feet. This
makes it easier to turn the screws.

7. Replace the base grille by aligning the ends of the grille with
the leveling assemblies on each side and snapping the grille

into place.

FILTERS AND ACCESSORIES

3. The water filter compartment is located in the right-hand
side of the refrigerator ceiling. Push up on the compartment

door to release the catch, then lower the door.

4.

Align the arrow on the water filter label with the cutout
notch in the filter housing and insert the filter into the

housing.

.

Turn the filter clockwise 90 degrees (1/4turn), until it locks
into the housing.

NOTE: If the filter is not correctly locked into the housing,
the water dispenser will not operate. Water will not flow

from the dispenser.

Do not use with water that is microbiologically unsafe or
of unknown quality without adequate disinfection before
or after the system. Systems certified for cyst reduction
may be used on disinfected waters that may contain
filterable cysts.

Install the Water Filter

.

Locate the accessory packet in the refrigerator and remove
the water filter.

2.

Take the water filter out of its packaging and remove the
cover from the O-rings. Be sure the O-rings are still in place

after the cover is removed.

A. O-ring cover

B. O-rings

6°

While the compartment door is still open, lift the filter up
into the compartment. Then, close the filter compartment

door completely.

7.

Flush the water system. See "Flushing the Water Filter" in the
"Water and Ice Dispensers" section.

IMPORTANT: If you do not flush the water system, you may
experience dripping and/or decreased flow from the water

dispenser.

16

The Water Filter Status Light

Press SETTINGS on the control panel to launch the Settings
menu. Press SETTINGS, under Filter Status, again to display the

percentage of filter life remaining (from 99% to 0%). PressICE/
WATER, under Back, to return to the Normal screen.

The water filter status lights will help you know when to change
your water filter.

• ORDER FILTER (yellow) - it is almost time to change the
water filter. While you are dispensing water, "Order Filter"

will blink seven times and sound an alert tone three times.
REPLACE FILTER(red) - Replace the water filter. While you

are dispensing water, "Replace Filter" will blink seven times
and an alert tone will sound three times.

RESETthe water filter status tracking feature. After you
replace the disposable filter with a new filter, closing the

filter compartment door will automatically reset the filter
status tracking feature. See "Using the Control(s)."

NOTE: "REPLACE FILTER" will remain illuminated if a filter is
not installed or is installed incorrectly.

Replace the Water Filter

To purchase a replacement water filter, see "Accessories" in the
User Guide, Use and Care Guide or User Instructions.

Replace the disposable water filter when indicated on the water
filter status display or at least every 6 months. If water flow to

your dispenser or ice maker decreases noticeably, change the
water filter sooner.

1. Locate the water filter compartment in the right-hand side
of the refrigerator ceiling. Pushup to release and lower the
compartment door.

2. Turn the water filter counterclockwise (to the left), and pull it
straight out of the compartment.

NOTE: There may be some water in the filter. Some spilling
may occur. Use a towel to wipe up any spills.

.

Install the replacement water filter by following steps 2

through 7 in the "Install the Water Filter" section.

s<s Ab s:e

An air filter is 15 times more powerful than baking soda at
reducing common food odors inside the refrigerator.

On some models, your refrigerator's accessory packet includes
an air filter, which must be installed prior to use.

Installingthe Air Filter

Install the air filter behind the vented door, located on the rear

wall near the top of the refrigerator compartment.

1. Remove the air filter from its packaging.

2. Lift open the vented door.

3. Snap the filter into place.

A. Air filter

Installing the Filter Status Indicator

The filter comes with a status indicator, which should be
activated and installed at the same time the air filter is installed.

1. Place the indicator face-down on a firm, flat surface.

2. Apply pressure to the bubble on the back of the indicator
until the bubble pops to activate the indicator.

17

3. Lift open the vented air filter door. On some models, there
are notches behind the door.

Models with notches:

With the indicator screen facing outward, slide the
indicator down into the notches.

NOTE: The indicator will not easily slide into the notches
if the bubble has not been popped.

Close the air filter door, and check that the indicator is
visible through the window in the door.

C

A. Status indicator window

B. Air filter status indicator

C. Notches

REFRIGERATORUSE

t %! i,,,1_>/ ii / {Ii_

There are two refrigerator compartment doors. The doors can
be opened and closed either separately or together.

There is a vertically-hinged seal on the left refrigerator door.

• When the left side door is opened, the hinged seal
automatically folds inward so that it is out of the way.

• When both doors are closed, the hinged seal automatically
forms a seal between the two doors.

A

Models without notches=

• Place the indicator somewhere it is easily visible - either
inside the refrigerator, or elsewhere in your kitchen or

home.

Replacing the Air Filter

The disposable air filter should be replaced every 6 months,
when the status indicator has completely changed from white to

red.
To order a replacement air filter, contact us. See "Accessories"

in the User Guide, Use and Care Guide or User Instructions for
information on ordering.

1. Remove the used air filter by squeezing in on the side tabs.

2. Remove the used status indicator.

3. Install the new air filter and filter status indicator using the

instructions inthe previous sections.

Replacement Parts.

To order stainless steel cleaner or replacement filters, call
1-800-4-MY-HOME ® and ask for the appropriate part number

or contact your authorized Kenmore dealer.
Stainless Steel Cleaner and Polish=

Order Part #D22 M40083 R
Water Filter=

Order Part #46-9924 (P6RFWB2)

Air Filter:

Order Part #WlO335147A
Produce Preserver.

Order Part #WlO335145A

A. Hinged

seal

Usi }g Cess'l 'ols

, == =,,_, , i +

The controls are located above the external dispenser.

18

IMPORTANT." The display screen on the dispenser control panel
will turn off automatically and enter "sleep" mode when the

control buttons and dispenser paddles have not been used for
2 minutes or more. Press any control button to reactivate the
display screen. The home screen will appear as shown.

Viewing and Adjusting Temperature Set Points

For your convenience, your refrigerator and freezer controls are
preset at the factory.

When you first install your refrigerator, make sure that the
controls are still set to the recommended set points. The factory
recommended set points are 37°F (3°C) for the refrigerator and

0°F (-18°C) for the freezer.
IMPORTANT:

• Wait 24 hours before you put food into the refrigerator. If
you add food before the refrigerator has cooled completely,

your food may spoil.
NOTE" Adjusting the set points to a colder than

recommended setting will not cool the compartments any
faster.

View Temperature Set Points

1. Press and hold TEMP for 3 seconds to activate Temperature
mode.

NOTE. To view temperature in degrees Celsius, press the
ACCENT LIGHT button, under Units, when adjust mode is

activated. To return the display setting to Fahrenheit, press
the ACCENT LIGHT button again.

When Temperature mode is activated, press TEMP to toggle
between Fridge and Freezer. The display will show the

temperature set point of the selected compartment, and
temperature adjusting information will appear on the

display screen.

Recommended Refrigerator Temperature

Recommended Freezer Temperature

If the temperature is too warm or too cold in the refrigerator

or freezer, first check the air vents to be sure they are not
blocked before adjusting the controls.

The recommended settings should be correct for normal
household use. The controls are set correctly when milk or

juice is as cold as you like and when ice cream is firm.

NOTE. Areas such as a garage, basement or porch, may
have higher humidity or extreme temperatures. You may

need to adjust the temperature away from the
recommended settings to accommodate for these

conditions.

• Wait at least 24 hours between adjustments. Recheck the
temperatures before other adjustments are made.

Adjust Temperature Set Points

Refrigerator set point range: 33°F to 45°F (0°C to 7°C).
Freezer set point range: -5°F to 5°F (-21°C to -15°C).

1. When Temperature mode is activated, press TEMPERATURE
to select the Refrigerator zone. The display will show the
temperature set point of the selected compartment, as

shown.

2.

Press LOCI( to raise the set point, or press SETTINGS to
lower the set point.

3.

When you have finished viewing (and adjusting if desired)
the refrigerator set point, press TEMP, under Select Zone, to
change the display to show the freezer set point. When the

zone has been changed, "FREEZER" appears on the display
screen.

4. Press the LOCI( button to raise the set point, or press the
SETTINGS button to lower the set point.

19

Save/Confirm Temperature Settings

• When you have finished adjusting both the refrigerator and
freezer set points, press MEASURED FILLto confirm and to

save the settings.

NOTE" Toexit Temperature mode without saving changes, press
the ICE/WATER button under Back at any time, or allow about
60 seconds of inactivity. The temperature mode will turn off

automatically and return to the normal screen.

When adjusting temperature set points,

use the followinc chart as a guide:

CONDITION= TEMPERATURE

ADJUSTMENT=

REFRIGERATOR too cold REFRIGERATOR Setting

1° higher

REFRIGERATOR too warm REFRIGERATOR Setting

1° lower

FREEZERtoo cold FREEZERSetting 1° higher

FREEZERtoo warm / FREEZERSetting 1° lower
Too little ice

Pressthe ICE/WATER button at any time to return to the Normal
screen.

Acceler-lce

The Acceler-lce feature assists with temporary periods of heavy
ice use by increasing ice production.

• To turn on the Acceler-lce feature, press the SETTINGS
button to access the Settings menu, then press TEMP, under
Acceler-lce to activate the feature. When the feature is on,

the Acceler-lce icon will appear on the dispenser display
screen. The Acceler-lce feature will remain on for 24 hours

unless manually turned off.

Cooling On/Off

Your refrigerator and freezer will not cool when cooling is
turned off.

To turn cooling off, press and hold the LOCI< and
MEASURED FILLbuttons at the same time for 3 seconds. The

Cooling Off icon will blink seven times and then remain lit as
shown.

IMPORTANT.

To avoid unintentionally locking the dispenser or
changing other settings, press both buttons at exactly the

same time.
When cooling is off, the dispenser paddles and all

controls except Lock and Measured Fill are disabled.

To manually turn off the Acceler-lce feature, press the
SETTINGS button to enter Settings mode (unless you are

already in Settings mode), then press TEMP,under
Acceler-lce, again. When the feature has been turned off,

the Acceler-lce icon will disappear from the dispenser
display.

Filter Status
Displays the percentage of use remaining in the water filter

(from 100% remaining to 0% remaining).
Toaccess Filter Status, press the SETTINGS button to access the

Settings menu, then press SETTINGS, under Filter Status, to
display the percent of life remaining in the water filter.

ALSO
The water filter status lights will let you know when to change

your water filter.

• ORDER FILTER (Yellow) - Order a replacement water filter.

• REPLACE FILTER (Red) - Replace the water filter. Replacing
the disposable water filter will automatically reset the water

filter status tracking feature. See "Water Filtration System."
NOTE: REPLACE FILTER will remain illuminated if a filter is

not installed or installed incorrectly.

A. PressLOCI< and MEASURED FILLat the same time.

• Press and hold LOCI< and MEASURED FILL for 3 seconds
again to turn cooling back on.

Settings

Pressthe SETTINGS button to open the Settings menu and select
between Acceler-lce, Filter Status or Vacation modes.

2O

Vacation Mode

In Vacation Mode, the freezer will defrost less often to conserve
energy.

• To turn on Vacation mode, press the SETTINGS button to
access the Settings menu, then press LOCI(, under Vacation,

to activate the feature. When the feature is on, the Vacation
icon will appear on the dispenser display screen as shown.

To turn off Vacation Mode, press the SETTINGS button to
access the Settings menu, then press LOCI( to turn off the

feature. The Vacation icon will disappear, and the screen
will display the settings as they were before Vacation Mode
was turned on.

NOTES:

During the first hour after Vacation Mode is turned on,
opening and closing the refrigerator door will not affect the

setting. After 1 hour has passed, opening and closing the
refrigerator door will turn off Vacation Mode.

• While in Vacation Mode, if Fast Ice is turned on or the Door
Ajar alarm sounds, Vacation Mode will be canceled.

Additional Features

Door Ajar Alarm

The Door Ajar Alarm feature sounds an alarm when the
refrigerator door(s) or freezer drawer is open for 5 minutes and

cooling is turned on. The alarm will repeat every 2 minutes.
Close all doors and drawer to turn it off. The feature then is

reset and will reactivate when either door is left open again for
5 minutes.

NOTE= To mute the audible alarm while keeping the doors
open, such as while cleaning the inside of the refrigerator,

press any button on the control panel. The alarm sound will
be temporarily turned off, but the Door Ajar icon will still be

displayed on the dispenser control panel.

Ref ge_'e}_ __ e_s _,}}_s_e;i}_

Temperature Controlled Exterior Drawer

IMPORTANT= This control sets the temperature for this drawer
only.

Use the full-width drawer to store large party platters or dell
trays, or use a drawer organizer to store smaller items such as

yogurt, juice boxes and lunch meat for easy access.
Temperatures have been preset for the storage of. Cold Drinks,

Meats/Cheeses, Assorted Items and Fruits/Vegetables. These
preset temperatures cannot be adjusted.

Press SELECT to toggle through the temperature settings. The
icon will illuminate when it is selected.

EasySlide Bin

A shallow storage compartment with glass lids which slide from
side to side is located below and in front of the crisper drawers.

NOTE= This compartment is not temperature or humidity
controlled, so it is not recommended for storing leafy

vegetables.

D

Disabling Sounds

• To turn off control and dispenser sounds, pressand hold

ICE/WATER and MEASURED FILLat the same time for
3 seconds. All normal operating tones are disabled. Only
alert tones will be audible.

• To turn all sounds back on, press and hold ICE/WATER and
MEASURED FILLat the same time for 3 seconds again.

Showroom Mode
This mode is used only when the refrigerator is on display in a

retail store. If you unintentionally turn on Showroom mode, the
word "Showroom" will light up on the display. Exit Showroom

mode by pressing and holding ACCENT LIGHT and LOCI( at
the same time for 3 seconds.

F

A. Crisper drawer handles

B. Ec/sySIide bin

To remove EasySlide bin:

1. Remove all three crisper drawers.

2. Hold the upper sliding lid near the trim and lift up to
remove. Remove the lower lid.

3. Grasp the front of the bin with both hands, and lift up on the
front to remove.

To replace EasySlide bin:

1. Slightly tilt the rear of the bin upward.

2. Align the center rib and tabs on the EasySlide bin with the
ribs and slots in the cabinet.

3. Lower the bin into place.

21

Crisper Drawers Calibrate Measured Fill

To remove and replace the drawers:

1. Grasp the handle at the bottom of the drawer and slide the

drawer straight out to the stop. Lift the drawer off the
bottom guide.

2. Replace the drawer by placing it on the bottom drawer
guide and pushing it past the drawer stop into position.

To remove the crisper(s) cover:

1. Remove crisper drawers.

2. Holding the glass insert firmly with one hand, press up in
center of glass insert until it rises above the plastic frame.

Gently slide the glass insert forward to remove.

3. Lift the cover frame up and remove it.

To replace crisper(s) cover:

1. Fit back of cover frame into supports on side walls of the
refrigerator and lower the front of the cover frame into

place.

2. Slide rear of glass insert into cover frame and lower front
into place.

3. Replace crisper drawers.

Household water pressure may affect the accuracy of the
Measured Fill feature. So, for optimum performance of your

water dispenser, you must first calibrate Measured Fill.
IMPORTANT:

• Flush the water system before calibrating Measured Fill.

• For best results, calibration should be performed when water
is not being used in the house.

Place a sturdy measuring cup (1 cup [237 mL] size) on the
dispenser tray centered in front of the ice/water dispenser

paddle.
NOTE: Depending on your model, a measuring cup may be

provided.

_ _@_C@ _C_

IMPORTANT:

• Allow 3 hours for the refrigerator to cool down and chill
water.

• Allow 24 hours to produce the first batch of ice. Discard the
first three batches of ice produced.

• The dispensing system will not operate when either the
refrigerator door or freezer drawer is open.

Flush the Water System

Air in the water dispensing system can cause the water
dispenser to drip. After connecting the refrigerator to a water

source or replacing the water filter, flush the water system.
Flushing the water dispensing system forces air from the water

line and filter and prepares the water filter for use. Additional
flushing may be required in some households.

NOTE: As air is cleared from the system, water may spurt out of
the dispenser.

1. Using a sturdy container, depress and hold the water
dispenser paddle for 5 seconds.

2. Release the dispenser paddle for 5 seconds. Repeat steps 1
and 2 until water begins to flow.

3. Once water begins to flow, continue depressing and
releasing the dispenser pad (5 seconds on, 5 seconds off)

until a total of 3 gal. (12 L) has been dispensed.

A. ice/Water dispenser paddle

B.Measuring cup (1 cup)

2.

Press and hold the SETTINGS and LOCI( buttons at the
same time for 3 seconds. The words "Back" and "1 Cup" will

appear on the display screen. Also, the Calibrate Measured
Fill icon will illuminate and remain lit while the Measured Fill

feature is being calibrated.

0

NOTE" You may press ICE/WATER "Back" at any time to
exit calibration mode. The Calibrate Measured Fill icon will

disappear.

22

3. • When changing from crushed to cubed, a few ounces of

Press and release the ice/water dispenser paddle, as
needed, to dispense water to the 1 cup fill line.

NOTE= If overfilling or spilling occurs, discard the water and
press ICE/WATER "Back" to restart the calibration process.

crushed ice will be dispensed along with the first cubes.

UUU

_4/oter Crushed Cubed

The Water Dispenser

IMPORTANT=

• Dispense at least 1qt (1 L) of water every week to maintain
a fresh supply.

• If the flow of water from the dispenser decreases, it could be
caused by low water pressure.

• With the water filter removed, dispense 1 cup (237 mL)

4. When 1cup of water has been correctly dispensed into the
measuring cup, press the MEASURED FILL button under the

word "Confirm" to confirm the calibration.

A

A. l cup of woter

o

When Measured Fill calibration has been confirmed the
icons will disappear and the display will return to the home

screen.

Dispensing

of water. If 1 cup (237 mL) of water is dispensed in
8 seconds or less, the water pressure to the refrigerator

meets the minimum requirement.

• If it takes longer than 8 seconds to dispense 1cup
(237 mL) of water, the water pressure to the refrigerator

is lower than recommended. See "Water Supply

Requirements" and "Troubleshooting" for suggestions.

To

Dispense Water (Standard)..

1.

Select water.

2°

Press a sturdy glass against the dispenser paddle.
NOTE= While dispensing water and for 3 seconds after

dispensing has stopped, the digital display will show how
much water has been dispensed.

3. Remove the glass to stop dispensing.

To Dispense Water (Measured Fill):
Measured Fill allows you to dispense a specified amount of

water with the touch of a few controls.
NOTE: The amount of water you select will be dispensed. Be

sure that the container is empty and can hold the entire volume.

If ice is in the container, you may need to adjust your selection.

1. Press MEASURED FILL to turn on the feature. When the
feature is on, the Measured Fill screen appears on the

display.

Press ICE/WATER to toggle through the following choices in a
continuous loop.

• Water (default) - Dispenses water

• Cubed - Dispenses cubed ice.

• Crushed - Dispenses crushed ice
NOTES;

The word "ICE" appears on the display screen when
either crushed or cubed ice is selected.

For crushed ice, cubes are crushed before being
dispensed. This may cause a slight delay when

dispensing crushed ice. Noise from the ice crusher is
normal, and pieces of ice may vary in size.

23

NOTES:

The dispenser will automatically turn off Measured Fill
after 1 minute of inactivity. When Measured Fill is turned

off, any changes you have made will be lost and all
defaults will be restored.

Press ICE/WATER "Back," to manually turn off the
Measured Fill feature.

2.

Press ACCENT LIGHT, under Units, to toggle among ounce,
cup and liter. The default unit is ounce.

Default, minimum, and maximum volumes are listed below.

Units Default Minimum Maximum

Ounces 8 1 128

Cups 1 1/4 16
Liters 0.25 0.05 4.00

.

Press LOCI< or SETTINGS to adjust the water volume as
desired. The LOCI< control increases the volume, and the

SETTINGS control lowers the volume.
NOTES:

• When increasing or decreasing the dispense volumes, if

an adjustment button (-/-t-) is held for approximately
10 seconds or longer the control may stop responding.

Release the button for approximately 2 seconds and
then continue making the adjustment.

• Most coffee cups (commonly 4 to 6 oz [118 to 177 mL]

per cup) are not the same size as a measuring cup (8 oz
[237 mL]). You may need to adjust the volume to avoid

unintentionally overfilling coffee cups.

4.

Dispense water.
NOTE: While dispensing water, the digital display will count

down how much water remains to be dispensed, according
to the volume you selected. The flow of water will

automatically stop once the desired volume has been
dispensed.

• Pressa sturdy glassagainst the dispenser paddle.

OR

• Place the glass below the water dispenser and press

MEASURED FILL, under Dispense, for hands-free
dispensing.

°

To stop dispensing before the selected volume has been
dispensed, remove the glass from the dispenser paddle OR
press MEASURED FILL a second time.

NOTE: If you stop dispensing before the desired volume has
been dispensed, the digital display will continue to show

how much water remains to be dispensed. The display will
turn off after 1 minute of inactivity.

To select a new volume or start dispensing the same
volume again, you must first finish dispensing the

selected volume, or turn off the Measured Fill feature
(either by waiting 1minute so it will automatically turn

off or by pressing ICE/WATER "Back" to manually turn it
off) and then turn it back on.

The Ice Dispenser

IMPORTANT:

If the ice cubes are hollow or have an irregular shape, it

could be because of low water pressure. See "Water Supply
Requirements."

Ice travels from the ice storage bin through the dispenser

chute to the dispenser. To turn off the ice maker, see "Ice
Maker and Storage Bin."

To Clean the Ice Dispenser Chute:

Humidity causes ice to naturally clump together. Ice particles
can build up until the ice dispenser chute becomes blocked.

If ice is not dispensed regularly, it may be necessary to empty

the ice storage bin and clean the ice delivery chute, the ice
storage bin and the area beneath the storage bin every

2 weeks.

• Remove the ice clogging the storage bin and delivery chute,
using a plastic utensil if necessary.

• Clean the ice delivery chute and the bottom of the ice
storage bin using a warm, damp cloth, then dry thoroughly.

To Dispense Ice:

1. Select the desired type of ice. To switch between cubed ice

and crushed ice, press ICE/WATER.

Cut Hazard

Use a sturdy glass when dispensing ice.
Failure to do so can result in cuts.

2°

Press a sturdy glass against the dispenser paddle. Hold the
glass close to the dispenser opening so ice does not fall

outside of the glass.
IMPORTANT: You do not need to apply a lot of pressure to

the paddle to activate the ice dispenser. Pressing hard will
not make the ice dispense faster or in greater quantities.

3. Remove the glass to stop dispensing.

NOTE: Ice may continue to dispense for several seconds after
removing the glass from the dispenser paddle. The dispenser

may continue to make noise for a few seconds after dispensing.

The Dispenser Light

When you use the dispenser, the light will automatically turn on.
To turn on the light when you are not dispensing.

PressACCENT LIGHT to toggle through the following choices in
a continuous loop:

• OFF (default) - The dispenser light is off

24

• ON - The dispenser light remains on at 100% brightness

• DIM - The dispenser light remains on at 50% brightness
The dispenser lights are LEDsthat cannot be changed. If it

appears that your dispenser lights are not working, see
"Troubleshooting" for more information.

Ice Production Rate

The ice maker should produce approximately 3 Ibs (1.4 kg)
of ice per day under normal operation.

To increase ice production, select the increased ice
production feature from the Settings or Options menu on the

control panel. See "Using the Control(s)."

C) C)

I

v

ON DIM

The Dispenser Lock

The dispenser can be turned off for easy cleaning or to avoid
unintentional dispensing by small children and pets.

NOTE: The lock feature does not shut off power to the
refrigerator, to the ice maker, or to the dispenser light. It simply
deactivates the controls and dispenser paddles. Toturn off the

ice maker, see "Ice Maker and Storage Bin."

• Press and hold LOCI( for 3 seconds to lock the dispenser.

• Press and hold LOCI( a second time to unlock the dispenser.
The display screen indicates when the dispenser is locked.

ZOCKED UNZ OCKED

ce Ngske <c s8ce 9 o s(3e

IMPORTANT: To avoid low ice production and poor quality ice,
flush the water system before turning on the ice maker. See
"Water Dispenser."

• Allow 24 hours to produce the first batch of ice. Discard the
first three batches of ice produced. Allow 2 to 3 days for the

storage bin to fill completely following installation.
The quality of your ice will be only as good as the quality of

the water supplied to your ice maker. Avoid connecting the
ice maker to a softened water supply. Water softener

chemicals (such as salt) can damage parts of the ice maker
and lead to poor quality ice. If a softened water supply

cannot be avoided, make sure the water softener is
operating properly and is well maintained.

If the ice in the storage bin clumps together, break up ice

using a plastic utensil and discard. Do not use anything
sharp to break up the ice. This can cause damage to the ice

bin and the dispenser mechanism.

• Do not store anything in the ice storage bin.

Ice Maker

The ice maker is located on the left-hand side of the refrigerator
compartment ceiling. Ice cubes are ejected into the ice storage

bin, located on the left-hand refrigerator door.
Turnthe Ice Maker On/Off

1. Push up on the latch on the left-hand side of the ice
compartment to open the door.

A. Ice compartment door

latch

2.

Turn on the ice maker by moving the switch to the (left) ON
position.

NOTES:

To manually turn off the ice maker, move the control to
the OFF (right) position.

Your ice maker has an automatic shutoff. The sensor will
automatically stop ice production if the storage bin is

full, if the door is open or the storage bin is removed.
The control will remain in the ON (left) position.

A

A. /ce storage bin re/ease/arch

3. Close the ice compartment door.

25

Remove and Replace the Ice Storage Bin

• Remove the ice storage bin by inserting your fingers into the

hole at the base of the bin and squeezing the latch to
release the bin from the compartment. Lift the storage bin

up and pull it straight out.

• Replace the storage bin inside the ice compartment and
push down to make sure it isfirmly in place.

REFRIGERATORCARE

Style 2 - Stainless Steel

IMPORTANT:

• Damage to stainless steel finish due to improper use of
cleaning products, or using non-recommended cleaning
products, is not covered under the warranty.

DO USE DO NOT USE

I/ Soft, clean cloth X Abrasive cloths

X Paper towels or newsprint
X Steel-wool pads

Explosion Hazard

Use nonflammable cleaner.
Failure to do so can result in death, explosion, or fire.

Both the refrigerator and freezer sections defrost automatically.
However, clean both sections about once a month to avoid

buildup of odors. Wipe up spills immediately.

Exterior Cleaning

Please see the exterior cleaning information specific to your
model.

Style 1 - Smooth Door
IMPORTANT: Damage to smooth finish due to improper use of

cleaning products, or using non-recommended cleaning
products, is not covered under the warranty. Sharp or blunt

instruments will mar the finish.

DO USE DO NOT USE

I/Soft, clean cloth X Abrasive cloths

X Paper towels or newsprint
X Steel-wool pads

I/ Warm, soapy water - X Abrasive powders or liquids

use a mild detergent X Window sprays 1.

X Ammonia 2.
X Acidic or vinegar based

cleaners

X Oven cleaners
X Flammable fluids

NOTE: Paper towels scratch and may dull the clear coat of the
painted door. To avoid possible damage use only soft clean
clothes to polish and wipe the door.

I/ Warm, soapy water

V' For heavy soil, ONLY X

a stainless steel
cleaner designed for

appliances. Toorder
the cleaner, see

"Accessories."

NOTES:

• If unintentional contact does occur, clean plastic part with a
sponge and mild detergent in warm water. Dry thoroughly

with a soft cloth.
Just because a cleaner is a liquid does not mean it is

nonabrasive. Many liquid cleansers formulated to be gentle
on tile and smooth surfaces still damage stainless steel.

Citric acid permanently discolors stainless steel. Toavoid
damaging the finish of your stainless steel refrigerator:

Do not allow these substances to remain on the finish

X Mustard X Citrus-based sauces

X Tomato juice X Citrus-based products
X Marinara sauce

X Abrasive powders or liquids
X Ammonia

X Citrus-based cleaners
X Acidic or vinegar-based

cleaners

X Oven cleaners

Stainless steel cleaner is for
stainless steel parts only! Do

not allow the Stainless Steel
Cleaner and Polish to come

into contact with any plastic

parts such as the trim pieces,
dispenser covers or door
gaskets.

Interior Cleaning

Unplug refrigerator or disconnect power.
Hand wash, rinse, and dry removable parts and interior

surfaces thoroughly. Use a clean sponge or soft cloth and a
mild detergent in warm water.

NOTE: Do not use abrasive or harsh cleaners such as
window sprays, scouring cleansers, flammable fluids,

cleaning waxes, concentrated detergents, bleaches or
cleansers containing petroleum products on plastic parts,

interior and door liners or gaskets.

3. Plug in refrigerator or reconnect power.

26

Condenser Cleaning

There is no need for routine condenser cleaning in normal home
operating environments. If the environment is particularly greasy

or dusty, or there is significant pet traffic in the home, the
condenser should be cleaned every 2 to 3 months to ensure

maximum efficiency.
If you need to clean the condenser.

1. Unplug refrigerator or disconnect power.

2. Remove the base grille.

3. Use a vacuum cleaner with a soft brush to clean the grille,
the open areas behind the grille and the front surface area

of the condenser.

4. Replace the base grille when finished.

5. Plug in refrigerator or reconnect power.

If You Choose to Turn Off the Refrigerator Before You

Leave:

1. Remove all food from the refrigerator.

2. If your refrigerator has an automatic ice maker:

• Turn off the water supply to the ice maker at least one
day ahead of time.

• When the last load of ice drops, raise the wire shutoff
arm to the OFF (up) position or press the switch to OFF,

depending on your model.

3. Turn off the Temperature control(s). See "Using the
Control(s)."

4. Clean refrigerator, wipe it, and dry well.

5. Tape rubber or wood blocks to the tops of both doors to
prop them open far enough for air to get in. This stops odor

and mold from building up.

Moving

The lights in both the refrigerator and freezer compartments are
LEDs which do not need to be replaced. If the lights do not

illuminate when the door or drawer is opened, call
1-800-4-MY-HOME ® for assistance or service.

If the power will be out for 24 hours or less, keep the door or
doors closed (depending on your model) to help food stay cold

and frozen.
If the power will be out for more than 24 hours, do one of the

following:

• Remove all frozen food and store it in a frozen food locker.
Place 2 Ibs (907 g) of dry ice in the freezer for every cubic

foot (28 L) of freezer space. This will keep the food frozen
for 2 to 4 days.

If neither a food locker nor dry ice is available, consume or

can perishable food at once.

REMEMBER=A full freezer stays cold longer than a partially
filled one. A freezer full of meat stays cold longer than a freezer
full of baked goods. If you see that food contains ice crystals, it

may be refrozen, although the quality and flavor may be
affected. If the condition of the food is poor, dispose of it.

Vacations

If You Choose to Leave the Refrigerator On While You're
Away..

1. Use up any perishables and freeze other items.

2. If your refrigerator has an automatic ice maker, and is
connected to the household water supply, turn off the water

supply to the refrigerator. Property damage can occur if the
water supply is not turned off.

3. If you have an automatic ice maker, turn off the ice maker.
NOTE= Depending on your model, raise the wire shutoff arm

to OFF (up) position, or press the switch to OFF.

4. Empty the ice bin.

When you are moving your refrigerator to a new home, follow
these steps to prepare it for the move.

1. If your refrigerator has an automatic ice maker:

• Turn off the water supply to the ice maker at least one
day ahead of time.

• Disconnect the water line from the back of the

refrigerator.

• When the last load of ice drops, raise the wire shutoff
arm to the OFF (up) position or press the switch to OFF,

depending on your model.

2. Remove all food from the refrigerator and pack all frozen
food in dry ice.

3. Empty the ice bin.

4. Turn off the Temperature control(s). See "Using the
Control(s)."

5. Unplug refrigerator.

6. Clean, wipe, and dry thoroughly.

7. Take out all removable parts, wrap them well, and tape
them together so they don't shift and rattle during the move.

8. Depending on the model, raise the front of the refrigerator
so it rolls more easily OR raise the leveling screws so they

don't scrape the floor. See "Adjust the Door(s)" or "Door
Closing and Door Alignment."

9. Tape the doors closed and tape the power cord to the back
of the refrigerator.

When you get to your new home, put everything back and refer
to the "Installation Instructions" section for preparation

instructions. Also, if your refrigerator has an automatic ice
maker, remember to reconnect the water supply to the

refrigerator.

27

PROBLEMSOLVER

Firsttry the solutionssuggestedhere or visit ourwebsite to possiblyavoid the costof a service call.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.
Do not remove ground prong.

Do not use an adapter.
Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

GENERAL OPERATION

Refrigerator will not operate

Motor seems to run too much •

Lights do not work Your refrigerator has been equipped with LED lighting which does not need to be replaced - If

Possible Causes and/or Recommended Solutions

• Not connected to an electrical supply - Plug the power cord into a grounded 3 prong outlet.
Do not use an extension cord.

No power to the electrical outlet - Plug in a lamp to see if the outlet is working.
Household fuse has blown or circuit breaker has tripped - Replace the fuse or reset the circuit

breaker. If the problem continues, contact a licensed electrician.
Control or cooling is not turned on - Turn on the refrigerator control, or turn cooling on.

See "Using the Controls."
New installation - Following installation, allow 24 hours for the refrigerator and freezer to cool

completely.
NOTE. Adjusting the temperature control(s) to the coldest setting will not cool either

compartment (refrigerator or freezer) more quickly.
Refrigerator control is in Showroom mode (on some models)- If the refrigerator is in Showroom

mode, cooling is turned off and "Showroom" will be illuminated on the control panel. See
"Using the Control(s)" for more information.

Your new refrigerator has an energy-efficient motor - The refrigerator may run longer than
you're used to, because the compressor and fans operate at lower speeds that are more

energy-efficient. This is normal.
NOTE. Your refrigerator may run even longer if the room is warm, a large load of food is

added, the doors are opened often, or if a door has been left open.

there is power to the refrigerator and the lights do not illuminate when a door or drawer is
opened, call for service or assistance. See either the front cover or the Warranty for contact

information.

28

The dispenser light is set to OFF - On some models, the dispenser light will operate only when
the dispenser paddle is pressed. If you want the dispenser light to stay on continuously, see

"Water and Ice Dispensers."
Doors have been open longer than 10 minutes - Close the doors and drawers to reset, and open

to resume lighted task.

GENERAL OPERATION Possible Causes and/or Recommended Solutions
Exterior drawer control not • The refrigerator is in Cooling Off mode - Exit Cooling Off mode. See "Using the Control(s)."

lit/unresponsive • The refrigerator controls' initialization process did not complete successfully - Unplug the

refrigerator, wait 5 seconds. Plug in the refrigerator, and wait 30 seconds before opening the
doors or drawers, or touching the control panel.

• The drawer front was recently removed - Make sure the temperature control wires have been
properly reconnected. See "Remove and Replace Drawer Fronts."

Refrigerator seems noisy The compressor in your new refrigerator regulates temperature more efficiently and uses less

energy than older models. During various stages of operation, you may hear normal operating

sounds that are unfamiliar.

The following noises are normal:

• Buzzing/Clicking - Heard when the water valve opens and closes to dispense water or fill the
ice maker. If the refrigerator is connected to a water line, this is normal. If the refrigerator is not

connected to a water line, turn off the ice maker.

• Repetitive Clicking - Dual evaporator valve regulating the cooling operation.

• Cracking/Clatter - Heard when ice is ejected from the ice maker mold and then falls into the
ice storage bin.

• Popping - Heard when the inside walls contract/expand, especially during initial cooldown.

• Hissing/Dripping - Flow of refrigerant, or flow of oil in the compressor.

• Pulsating/Whirring - Heard when the fans/compressor adjust to optimize performance during
normal operation.

• Rattling - Heard when water passes through the water line, or due to the flow of refrigerant.
Rattling may also come from items placed on top of the refrigerator.

• Water running or gurgling - Heard when ice melts during the defrost cycle and water runs into
the drain pan.

• Sizzling - Heard when water drips onto the heater during the defrost cycle.

• Vibration - The refrigerator may not be steady. Adjust the leveling screws and lower the
leveling foot until it is firmly against the floor. See "Refrigerator Leveling, Door Closing and

Alignment."

Temperature istoo warm • New installation - Following installation, allow 24 hours for the refrigerator and freezer to cool

completely.
NOTE. Adjusting the temperature control(s) to the coldest setting will not cool either

compartment (refrigerator or freezer) more quickly.

• Cooling is turned off - Turn on cooling. See "Using the Control(s)."

• Doors are opened often or not closed completely - This allows warm air to enter the
refrigerator. Minimize door openings, keep the doors fully closed, and make sure both doors
are properly sealed.

• Air vents are blocked - Remove items that are immediately in front of the vents.

• Large amount of warm food recently added - Allow several hours for the refrigerator to return
to its normal temperature.

• Controls are not set correctly for the surrounding conditions - Adjust the controls to a colder
setting. Check the temperature again in 24 hours.

Temperature istoo cold in

the refrigerator/crisper

Temperature istoo warm/
cold in the exterior drawer

• Controls are not set correctly for the surrounding conditions - Adjust the controls to a warmer
setting. Check the temperature again in 24 hours.

• Ice storage bin is not in the correct position - See "Ice Maker and Ice Storage Bin."

• Air vents are blocked - Remove items that are immediately in front of the vents.

• Control is not set correctly for the items stored in the drawer - Adjust the temperature setting.
See "Temperature Controlled Exterior Drawer."

29

GENERAL OPERATION PossibleCauses and/or Recommended Solutions

Interior moisture buildup NOTE: Some moisture buildup is normal. Clean with a soft dry cloth.

• Room is humid - A humid environment contributes to moisture buildup. Only use the refrigerator
in an indoor location, with as little humidity as possible.

• Doors are opened often or not closed completely - This allows humid air to enter the
refrigerator. Minimize door openings, keep the doors fully closed, and make sure both doors

are properly sealed.

Frost/Ice buildup in the

freezer compartment

• The drawer is opened often or left open - Minimize drawer openings and close drawer
completely after use.

• Poor drawer seal - Ensure drawer seal is making full contact with the cabinet to allow for an
adequate seal.

• Temperature control(s) are not set correctly - See "Using the Control(s)" for recommended
temperature settings.

Explosion Hazard

Use nonflammable cleaner.

Failureto do so can result in death, explosion, or fire.

DOORS AND LEVELING Possible Causes and/or Recommended Solutions
Doors are difficult to open • Gaskets are dirty or sticky - Clean the gaskets and contact surfaces with mild soap and warm

water. Rinse and dry with a soft cloth.

Doors will not • Door is blocked open - Move food packages away from the door. Make sure all bins and
close completely shelves are in their correct positions. Make sure all packaging materials have been removed.

Doors appear to be uneven • Doors need to be aligned, or refrigerator needs to be leveled - See "Refrigerator Leveling, Door

Closing and Alignment."

Refrigerator unsteady or it • Refrigerator brake feet are not snug against the floor - Remove the base grille. Turn both brake
rolls forward when opening feet (one on each side) clockwise, the same amount, until they are snug against the floor. See

and closing doors or drawers "Refrigerator Leveling, Door Closing and Alignment."

3O