Kenmore 596.50019100 User Manual

;ide=by-Side Refrigerator

Use & Care Guide

Refrigerador DUplex Guia para el Uso y Cuidado

R_frig_rateur _ Compartiments Ju×tapos_s Guide D'utilisation et D'entretien

596.52672200,596_52673200,596.52674200,596.52679200,

596.50002100,596.50003100,596.50004100,596.50009100,

596.50012100,596.50013100,596.50014100,596.50019100

It"

M "a

12591310 Sears, Roebuck and Co, Hoffman Estates, IL 60179 USA wwwosears.com

Sears Canada, Inc, Toronto, Ontario, Canada M5B 2B8 Au Canada, www.sears.ca

a_Recognize this symbol as a safety alert indicator

[ WARNING j

To avoid electrical shock which can cause severe personal injury or death, do not cut or remove the round grounding

prong from the plug Refrigerator must be grounded at alf times Do not remove warning tag from cord, Do not use a two- prong adapter. Do not use an extension cord°

against possible shock hazards If you encounter a _o-prong receptacle, contact a qualified electdcian and have the two-prong wall receptacle replaced with a propedy grounded three-prong wall receptacle in accordance with the

Electrical Grounding Instructions-This refrigerator is equipped with a three-prong (grounding)plug for protection _Jl_ I

National Electrical Cede Refrigerator is designed to operate on a separate 103 to 126 volt, 15 amp, 60 cycle line,

l DANGER I

IMPORTANT: Child entrapment and suffocation are not problems of the past, Junked or abandoned refrigerators are still dangerous--even if they will sit for "just a few days" tf you discard an old refrigerator,

please follow the instructions below to help prevent accidents BEFORE YOU THROW AWAY YOUR OLD REFRIGERATOR OR FREEZER:

• Take off the doors,

• Leave the shelves in place so children may not easily climb inside,

We Service What We Sell

Your purchase has added value because you can depend on Sears HomeCentral® for service With over 12,000 trained repair specialists and access to over 4 2 million parts and accessories, we have the tools, parts, and knowledge and skills

to ensure our pledge: We Service What We Sell

Sears Maintenance Agreements

Your Kenrnore appliance is designed, manufactured and tested to provide years of dependable operation, Yet any major appliance may require service from time to time The Sears Maintenance Agreement offers you an outstanding service

program, afferdably priced The Sears Maintenance Agreement

Is your way to buy tomorrow's service at today's pdce Some limitations apply,, For more information, Eliminates repair bills resulting from normal wear and tear call 1-800-361-6665,,

Provides for nontechnical and instructional assistance Even if you don't need repairs, provides an annual Preventative For information concerning Sears Canada Maintenance Check, at your request, to ensure that your appliance Maintenance Agreements, call 1-800-361-666& is in proper running condition,

Full One Year Warranty on Refrigerator For one year from the date of purchase, when this refrigerator is operated and maintained according to instructions

attached to or furnished with it, Sears witl repair it, free of charge, if defective in matedaE or workmanship

Full Five Year Warranty on Sealed Refrigeration System For five years from the date of purchase, when this refrigerator is operated and maintained according to instructions

attached to or furnished with it, Sears will repair the sealed system (consisting of refrigerator, connecting tubing and

compressor motor) free of charge, if defective in material or workmanship The above warranty coverage applies only to refrigerators which are used for storage of food for private household

purposes It excludes odginal and replacement Kenmore ice & water filter cartridges (if equipped with the filter system).

Original and rep{acement cartridges are warranted for 30 days, parts only, against defects of matedal or workmanship. Warranty service is available by contacting 1-8004-MY-HOME (1-800-469-5811). This warranty applies only while this product is in use in the United States This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state.

Sears, Roebuck and Co., Dept 817WA, Hoffman Estates, IL 60179

......................... inlll,lnjUUlUitUlUllnl i I n i

Full One Year Warranty on Refrigerator

For one year from the date of purchase, when this refrigerator is operated and maintained according to instructions

attached to or furnished with it, Sears wi!l repair it, free of charge, if defective in matedai or workmanship

Full Five Year Warranty on Sealed Refrigeration System

Far five years from the date of purchase, when this refrigerator is operated and maintained according to instnJctions attached to or furnished with it, Sears wilt repair the sealed system (consisting of refrigerant, evaporator, and condenser)

free of charge, if defective in material or ,workmanship

Ten Year Parts Warranty on Compressor

For ten years from the date of purchase, when this refrigerator [s operated and maintained according to instructions attached to or fiJmished with it, Sears will replace any compressor part, if defective in matedal or workmanship+

The above warranty coverage applies only to refrigerators which are used for storage of food for private household purposes, it excludes originat and reptacement Kenmore filtered ice & water filter cartridges (if equipped with the filter syslem) Original and replacement cartridges are warranted for 30 days, parts only, against defects of matedal or

workmanship. Warranty service is available by contacting 1-800-4-MY+HOME or (1-800-469-5811),

Sears Canada, lnc, Toronto, Canada, M5B 2B8

In the space below record the model and sedal numbers and purchase date of your refrigerator You will find the model and

seria! number sticker inside the unit on the left wat+ of refrigerator section

Model Number: 596 Sedal Number:

Purchase Date:

Keep this booklet and your Sears sales receipt in a safe place for future reference.

iiii1,111111111ii ii i ii ii iiiiiil,lllnllllml, iii ........................

Recognize Safety Symbols, Words, Labels

[ DANGER ]

DANGER--Immediate hazards which WILL result in severe personaf injury or

death,

[ & WARNING ]

WARNING--Hazards or unsafe practices which COULD resuit in severe personal injury or death_

[ & CAUTION ]

CAUTION--Hazards or unsafe practices which COULD result in minor personal injury or product or property damage.

What You Need to Know

about Safety Instructions

Warning and important Safety Instructions appearing in this manual

are not meant to cover all possible conditions and situations that may

occur,, Common sense, caution, and care must be exercised when installing,

maintaining, or operating refrigerator, Always contact your dealer, distributor,

service agent, or manufacturer about problems or conditions you do not

understand

ElectricalRequirements....................................2

MaintenanceAgreement.....................................2

Warranbj.......................................................................2

Warranty-Canada................................... 3

ProductRecord..........................................3

ImportantSafetyInformation...............................3

InstallingYourRefrigerator................................5

HowtoTransportYourUnit.............................5

HowtoSelecttheBestLocalion...........................5

HowtoRemovetheDoorsandHinges..............6

Howto_nstallandRemoveHandles...............6

HowtoLevelYourRefrigerator.....................7

HowtoConnecttheWaterSupply.........................8

HowtoAdjusttheTemperatureControls..........9

AboutYourFiltrationSystem..............................I0

RefrigeratorFeatures.......................................11

DoorStorage..................................................11

Shelves......................................................................11

Drawers.......................................................11

FreezerFeatures............................................13

PrimaryFeatures.............................. !3

Drawers.............................................13

DoorStorage........................................13

Shelves.....................................................13

DispenserFeatures.................................14

WaterDispenserOperation.................. 14

ControlFeatures.....................................15

HintsandCare....................................... 19

HowtoCleanYourUnit.....................................19

HowtoRemoveandReplaceLightBulbs.......20

Troubleshooting.................................... 21

WaterFilterData................................................25

Espa5ol..........................................................28

Frangais...................................................53

Service................................................BackCover

Installing Your Refrigerator

These instructions were provided to aid you in the installation of your unit Sears cannot be responsible for improper installation

How to Transport Your Unit

Follow these tips when moving the unit to fina[ location:

NEVER transport unit on its side [f an upright position is not possible, lay

unit on its back Allow unit to sit upright for approximately 30 minutes prior to plugging unit in lo assure oil return to lhe compressor. Plugging unit in

immediately may cause damage to internal pads. Use an appliance doily when moving unit ALWAYS truck unit from its

side-NEVER from ils front or back. Protect outside finish of unit during transport by wrapping cabinet in

blankets or inserting padding between the unit and doily Secure unit to dolly firmly with straps or bungee cords Thread straps

through handles when possible DO NOT overtighten Ovedightening restraints may dent or damage outside finish

How to Select the Best Location

Observe these points when choosing the final location for your unit:

DO NOT install refrigerator near oven, radialor, or olher heat source If thai is not possible, shield refrigerator with cabinet material

DO NOT install where temperature felts below 55_F (t3°C) Malfunction may occur at this temperature.

Make sure floor is level If floor is not level, shim rear wheels of unit with a piece of plywood or other shim matedaL

To assure proper door closure, verify that the unit is tevefed with a ¼" tilt to the back

How to Remove and install Panels (some mode|s)

Reference the sheel entitled Decorator Door Panel Installation Instructions shipped on the front of your unit

How do I measure an opening

to insure proper fit?

This refrigerator was designed to fit a 69" tall opening to allow for proper ventilation,

leveling, and door adjustments.

Please also take into account, when

measuring space for your unit, that some

models require a certain amount of clearance around it to allow for proper air flow Proper air flow is key to keep your unit

running a optimum efficiency To determine

measurements, please reference the table

below.

Subf!ooring or floor coverings (i e carpet, tile, wood floors, rugs) may make your opening I-

smaller than anticipated

Some clearance may be gained by using the _I_

leveling procedure under "How to Level Your !1_

Refrigerator".

Unit Total

Volume

Less Than 23

eu. fL

Greater

Ihan 23 cu. ft.

IMPORTANT: If unit is to be installed into a

recess where top of unit is completely

covered, use dimensions from floor to top of

hinge cap to verify proper clearance

Recommended

Clearance

Sides Rear

NiA N/A N/A

V£' N/A W'

Installing Your Refrigerator

How to Remove the Doors and Hinges

Some installations require door removal to get refligerator to final location

[ _ WARNING

To avoid severe personal injury or death, observe the following:

• Disconnect power to refrigerator before removing doom Connect power only after replacing doors

• Green ground wire must be attached to top hinge while performing door removal and replacement

• Tape decorative panels (some models) securely into place before removing door handles

[ A_ CAUTION

To avoid property damage, observe the following:

• Protect soft vinyl or other flooring with cardboard, rugs, or other protective material, pdor to moving refrigerator

• To avoid damage or breakage to adjusting bolt, do not use power tools to correct leveling.,

• DO NOT adjust unit to be any shorter than 68 ½" inches tall (minus hinge and cap) Doing so may damage underside components

Detach main wire connector harness.

I emove toe grille and

bottom hinge covers.

, Open both doors I80% or as

wide as possible, to remove,

Unscrew union nut

to detach water tube.

(dispensing models onl._)

Use a fiat blade screwdriver or fingernail to press junction point between two connectors

to release

Detach red wire harness.

Press tab on underside of connector to release,

)

Remove top hinges along

with doors.

Remove top hinge cover by

removing Phillips screw.

Remove bottom hinges with a

Close doors, Unscrew "_6 ?

head screws from top hinges,

DO NOT remove either green ground

wire or wire connecting center screw

s/,, hex

3Is" hex head driver.

How to Replace the Doors

Remove the Doors and Hinges in reverse order

I • To replace doom, follow the steps in How to |

i i i iiiiiii iiii i iii iiiiiiiiiiiiii

How to Install and Remove Handles

Installing Front-Mounted Handles

If installing handles for the fi_st time, the flesh food handles can be located within the flesh food section. The handle trim wilt be located in the literature pack

3 screws emo;e in , LII1

screws £rom bottom o£

refrigerator and freezer

door_

and bottom sets o£ door dips, I _ t[

andslidedownuntos_ew I _ I/

holes on bottom o£handles --I_[_

match with door screw holes. _r_l[ -

in,oscrewhales bottom rill

)

Installing Your Refrigerator

How to Install and Remove Handles continued

Removing Front-Mounted Handles

Removing handles may be necessary when transporting unit through tight spaces

ii i

/1 ha_e_,m_a r_ t)Itl IllIz s_. P_,haoleo_,aod

[ sma11 Bat-blade screwdHrer. _l / out to release [rom uniL

/ iMPORTANT:Wrapb,adeofscrewdriverII I /

k, ,wi,!,h,,,maskingtape to a old damaging uNt J ,,,

Removing Full-Length Extruded Handles

Removing handtes may be necessary when transporting unit through tight spaces, or installing or replacing decorative panels.

l _h, WARNING I z

To avoid possible injury and damage to property, tape decorative panels (some models) securely into place before removing door handles. F

Fit may be

tight.

Fam_

ffa

Install Full-Length Extruded Handles

clips on doors. Insert J_[I

N Align notcheson beck r'_

dips into notches _!)tl

and slide handte down until it contacts bottom trier

Repeat instructions to install other handle

i i iii i -q

How to Level Your Refrigerator

MateriMs Needed

* al_" hex head ddver • Level

and bottom

I R=oreto_ gzille Binge corers !

f9 _u,obo__ontadjos=_t,_s_=.-yl

l" (A)a_ise toraiseand 0 _ I#...,?lll!

L counterclockwise to lower, e_.2 _J

............................... i I I III IIII IIII IIIIIIIIIIIIIII

screws (B) clockwise to _ I

[3 r=,_bo__=, adj_s==t __2--g]

rMse and countez'clockwis_, _ _ I

to forger )

and hinge covers

.€

I£ required, correct roddng o£ unit by

turning tear adjustment screw dock-wise to raise rocking corner.

If doors are unertm..

• Determine which door needs to be raised,

• Turn front roller adjustment screw clockwise to raise

front corner of door if the unit has reached the

limit of its adjustment range, ,,,_,,_ and doors are still not level-

lower opposite door by turning roller adjustment screw counterclockwise,

Check with level to verify ¼" tilt to the back for proper door closure

If unit is aligned and stable, replace toe grille and hinge covers

Installing Your Refrigerator

How to Connect the Water Supply

WARNING ]

To avoid electrical shock which can cause severe personal injury or death, disconnect power to refrigerator before connecting water supply After connecting water supply, connect power,

[ CAUTION i

To avoid property damage, observe the following:

• Consult a plumber to connect copper tubing to household plumbing to assure compliance with local codes and ordinances

• Confirm water pressure to water valve is between 20 and 100 pounds per square inch If water filter is installed, water pressure to water valve must be a minimum of 35 pounds per square inch.,

• DO NOT use a self-piercing, or 31)_"{4 8 mm) saddle valve Both reduce water flow, become clogged with time, and may cause leaks if repair is attempted

• Tighten nuts by hand to prevent cross threading Finish tightening nuts with pliers and wrenches Do not overtighten

• Wait 24 hours before placing unit into final position to check and correct any water leaks

Marerials Needed

• V4" (6 mm) outer diameter flexible copper tubing

• Brass nut and sleeve (see

literature pack)

• Shut-off valve (requires a V4" or 6

mm hole to be drilled into water

supply before valve attachment)

. Adjustable wrench

avoid kinks in tubing.

NOTE: Add 8' (2 m) to tubing length needed to reach

1 Create sezvice loop with tubing using care to

water supply for creation of service loop,.

cap from water valve inlet

p oz' t.

i2 emove plastic

1--_41<4:'" i

end as iBustzated°

P!ace brass nut and sleeve on copper tube __,,1

port, Shape tubing slightly-DO NOT KINK-so

that tubing [eeds straight into inlet porL

I4 PIace end of copper tubing into water valve inlet

Im Hde brass nut over sleeve and screw nut into inlet

potL Tighten nut with wrench. Pull on tubing to

confirm connection is secure.

IMPORTANT: DO NOT overtighten, Cross threading may occur

_6 Locate water tubing damp and install with ¼" hex 1' head screw, as illustrated. Turn on water supply

_andcorrectanyleaks, ifpresent.

water

_7 Monitor connection For 24 hours. Correct if

necessary.

leaks,

)

Installing Your Refrigerator

How to Adjust the Temperature Controls

This refrigerator is designed to operate at a household temperature of 55° to 110°F (t3 ° to 43 ° C)

Dial Temperature Control Models

For initial temperature setting, follow all five steps listed below. If doing a simple temperature modification for an operational unit, only steps 3 through 5 are required

in,i

I Locate reFrigerator and Check to see if freezer

Fre_er controls on upper temperature is 0 ° to 2° F (-I 7 °

left wall o£ refrigerator section, and set both

controls to 3 ½,

IMPORTANT: Neither section

will cool if freezer control is

set to Off

n ====,,,, == ==H=,,,,I=

(2 AIIov¢ 24 hoursfoz ]

L-- texnl_er_tures to stabilize,,, )

to-16 ° C).

Turn control to next highest number if too warm

Turn control to next lowest number if too cold

Allow 5 to 8 hours for adjustments to take effecL

l i u inlnllul n,,nll

Check to see that refrigerator

section is 38 ° to 40°F (3° to

4°C).

Turn control to next highest number if too warm

• Turn control to next lowest number if too cofd,

• Allow 5 to 8 hours for adjustments

_1 i IUU ,ii ,it, ,iii t ,t ti,ni ,,_

I5 J_e,_l_lt s_eps 3 _ 4 _ _s )

to take effect

necessary.

How do I perform a

with my dia!

temperature test _

temperature

controls?

IMPORTANT: These instructions apply to dial temperature controls

only Electronic control models constantly monitor unit

temperature on the controJs

l_fa retials needed

2 thermometers measuring -5 ° to 50_F (-21 ° to 10°C) r_

2 drinking glasses

For Freezer

Place thermometer in glass of BJ_ vegetable oil in midd4e of freezer and continue

with step 3 of How to Adjust

the Temperature Controls

section,

IMPORTANT: Due to design of unit, atways start temperature

adjustments with freezer section

For Refrigerator

Place thermometer in glass of

water in middle of unit and continue with step 3 of How to

Adjust the Temperature

Controls section

IilSU

Electronic Temperature Control Models

To set temperature of the Freezer, use the _"_ buttons next to the

@button. A setting o£0 ° to 2 ° F (-17 ° to-16 n C) is recommended.

Use the _ button to raise the temperature of the freezer section, or the v to

lower it.,

Press the _ button to confirm the

inl ulm ii,u i lnl ulnlJ,,i

To set the temperature of the Fresh Food section, use the ,,_,,

settings

buttons next to the _ buttono A setting 0£38 ° to 40 ° F (3 ° to 4 ° C) is reomme_dedo

Use the A button to raise the temperature of the fresh food section, or the v to lower iL

Press the _ button to confirm the settings

............................................................ ii

NOTE: If adjusting the temperature of an operational unit, only 5 to 8 hours is [

[3 A21o 24 hours for temperatures to stabiliz_ !

required for temperatures to take effect J

iii i nmn,,,H

Why do the

temperatures on my [3ED display

fluctuate after they

have been set?

The compartment temperatures

may vary slightly as the unit cycles

to maintain the set temperatures

About Your Filtration System...

Water Filter Removal and Installation

[ _ WARNING ]

To avoid serious illness or death, do not use unit where water is unsafe or of unknown quality without adequate

disinfection before or after use of filter,

[ CAUTION I

• Bypass cadridge DOES NOT filter water Be sure to have replacement cartridge available when filter change is required . If water filtration system has been aElowed to freeze, replace filter cartridge

• If system has not been used for several months, and water has an unpleasant taste or odor, flush system by dispensing 2-3 glasses of water If unpleasant taste or odor persists, change filter cartridge

Initial Install of Water Filter

When do I change the

water filter?

The dispenser features a water filter change indicator For

instructions on how to operate and reset this feature, refer to the

Dispenser Features section IMPORTANT: Condition of water

and amount used determines life span of water filter cartridge If

water use is high, or if water is of poor quality, replacement may need

to take place more often

How do I order a

replacement filter cartridge?

Kenmore _ replacement water filter cartridge modet 9005

is available through Sears dealers and servicers You may also order through Sears by using the

information on the back cover

I'm trying to dispense

water to flush the ]\_

system. Where's the water?

Dudng initial use, allow about a 1 to 2 minute delay in water dispersal to

ailow internal water tank to lilt

_I Removeblu_brpa_ _V.na __

p o flter,nd !

|, Rotate gently clockwise until filter stops _'-_" 7( i

k _ndsnap_Itercoverdosed......... _ _ )

Reduce water spurts by flushing air From

system, Run water continuously for 2 minutes through du'spenser until water' runs

steady,

• Additional flushing may be required in some households

_. where wa!er !s of poor qua!ity:

Replacing Water Filter

IMPORTANT: Air trapped in system may cause water and

cartridge to eject Use caution when removing

What if I choose not to

use the water filtration

system?

Dispenser feature may be used without water filter cartridge ff you

choose this option, replace filter with blue bypass cap

[_ FromTUrnfilterfltezhead.C°unterd°ckwise unti! Jtrele_ses-il]

i ,,,Hn4mu .......................

,u, =,=H

f _ Drain water From Elter into sink and )

Lz"d dispose in normM fiousd2oId garbage. )

continue with Initial Install of Water

3Wipe up excess water in filter cover and I

Filter, steps 2 _nd 3,

[ CAUTION ]

To avoid property damage or injury, observe the following:

Confirm shelf is secure before placing items on shelf Handle tempered glass shelves carefully Shelves may

break suddenly if nicked, scratched, or exposed to sudden

_ temperature change

Door Storage

Milk Savor TM (some models)

The temperature-controlled Mitk Savor TM keeps beverages and other items up to 5" F

(3= C) colder than the rest of the fresh food

section to pass to Milk Savor TM The Milk Savor TM control is located

sectionAirinleta,owsairfromthefreezer!I!(

on the ieft wall of fresh food section Control adjusts amount of air circulating in

Milk Savor TM Turn control clockwise for colder

temperature

To remove and install Milk Savor TM :

if located directly above Milk Savor TM, dairy center or door _!

bucket may need to be removed t t I !] Refer to appropriate thstrections I_i

and remove item Slide Milk Savor___ t

assembly up and pull straight out

To install, align one of the Ill

Mtik Savor" cold air intake _ll I\ holes (A) with one of the two ,._q],_B _.l

air inlets (B) in door liner A_::_I ]11]1 ti1 Push assembly down onto "_1'1'1'1'1'1'1'1'1'1=_{]{I I1

door liner retainer until it steps _" _-_t'_Ht ]I 1

IMPORTANT: Milk Savor TM will not operate properfy if air intake holes are not aligned with air inlet in door

liner

Dairy Center

The dairy center provides convenient storage for items such as butter, yogurt, cheese, etc..

This compartment is an adjustable feature located in the door It can be moved to several different locations

to accommodate storage needs

To remove and install bin:

• To remove, slide dairy center up

and pull out _b_

• To install, slide assembly in above desired door liner

retainer and push down until it stops

To remove and install dairy door:

• To remove, press in sides of dairy door and pull out

• To install, slide sides of dairy door inside da}ry

center until hinge points snap into place

iii i ullllllllllll

Refrigerator Features

Door Storage ,oatiaued

_Tilt-Out Door Buckets (some models)

The Tilt-Out Bucket assembly consists of a bucket and frame,

providing adjustable, convenient storage for food items in door The bucket assembly lilts forward for easy access of items, and

lifts out for ease in deaNng and adjusting To remove and install bucket:

To remove bucket, tip bucket forward and putl straight out to remove To install bucket, slide bucket into bucket frame and push bucket upfighL

To adjust bucket frame:

Remove bucket per above instructions

• Lift frame of[ door support and place in

_. desired door location. ......

Door buckets adjust to meet indMdual storage needs

To remove and install buckets:

• L_ the door bucket up unti_it dears the retainers on the door liner, then pull the door

bucket straight out

I Door Bucket; .........

To install, slide bucket in above desired door liner retainer and push down until bucket stops

Shelves

Spillproof Shelves

Spitlpmof stationary shelves hold simple spills for easier cleaning

To removeand install shelves:

To remove shek,es, lilt front of shelf to

release shelf hooks from metal track and pull out to remove

• To install shelves, select point in metal track for replacement

and insert sheff hooks Raise front of shelf until hooks lock into place Lower shelf fronL

Drawers

Rack (some models)

The Can rack slides out from underneath the spi!tproof stationary shelf. The can rack holds up to

tv_.elve 12-ounce beverage cans To remove and install can rack:

To remove, empty contents of can rack Pull can rack forward to full extension and lift front to release

from shelf rail. Pull straight out to remove

• To install, reverse above procedure.

Snack Drawer

This drawer can be used for storage of

food items or exba produce

To remove and install snack drawer.

• To remove, pull drawer out to full extension. Tilt up front of drawer and

pull straight ouL

• To install, reverse above procedure

I_ ii ilul I,IHIII

Refrigerator Features

What setting should I use for items in my temperature-controlled drawer?

YOU should not store lettuce or other leafy produce in this

drawer

. cauliflower • steaks

COLD .cucumbers COLDEST .hard cheeses

• zucchini • cold cuts . apples • bacon

• corn .hot dogs

• oranges

• grapes

D rawe rs

Temperature.Controlled Meat

Drawer

The temperature-controlled meat drawer provides a drawer with a vadable temperature control that keeps the compartment up to 5°F (3°C) colder than refrigerator

temperature This drawer can be used for de_i storage or

additional produce storage

NOTE: Cold air directed to the temperature-controlled meat drawer can lower refrigerator temperature

Refrigerator control may need to be adjusted Controls Located on the walt to the left of the drawer, the climate

controls regulate the air temperature in the temperature- controlled meat drawer Set control level to cold to provide

normal refrigerator temperature for non-leafy produce Use the coldest setting for meats or other

deli items, To remove and install drawer:

To remove, pull drawer out to fulr extension. Tilt up front of

drawer and pul_ straight out To install, guide drawer into

frame and push back until drawer is flush with rear wall

What setting should I use for items in my humidity-controlled drawers?

LOW

HIGH

• cauliflower • oranges • grapes

• apples • zucchini ° corn

• cucumbers • cabbage .fresh

• lettuce • celery sprouts

• asparagus • broccoli • fresh herbs

• spinach

What can I do to prolong the life of my

produce?

Please observe the foltowingjules when storing produce in humidity-centre!led crispers:

DO NOT wash produce before placing in crispers Any additional moisture added to the crispers may cause produce to prematureiy spoil

DO NOT line crispers with paper towers, Towels will retain moisture.

Fettow control instructions carefully Incorrect control settings may damage produce

Humidity-Controlled Crisper

The humidity-controlled crisper keeps produce fresh longer by providing an environment with adjustable

humidity Controls

The humidity-controlled crisper controls regulate the amount of humidity in the crisper drawer Use the low

setting for nen4eafy produce Use the high setting for leafy

produce

To remove and install drawer:

• To remove, pull drawer out to full extension Tilt up front of drawer and pull straight out

. To install, guide drawer into

frame and push back until drawer is flush with rear wall

To remove and install shelfi

. To remove, lift shelf from walt supports

• To install sheff, bwer shelf onto wall supports and

push in unlil shelf is fiush with rear wall

[ CAUTION l

To avoid property damage, observe the following:

• Do not force ice maker arm down or up

• Do not place or store anything in ice storage bin..

WARNING I

To avoid possible injury, including death, do not place glass

items in ice cream shelf Glass objects may shatter or explode if exposed to extreme cold

Freezer Features

iii i illlll

Ice Cream Shelf

tce cream shelf provides a space for items to be chilled or frozen quickly

• To remove, lift ice cream shelf from ice bin rails and pull straight out.

• To install, fit shelf over top of ice maker and lower onto ice bucket rails

Primary Features

l,J

Automatic Dispensing Ice Maker

This ice maker creates the ice used in the dispensing system

Using Ice Maker for the First Time

Confirm ice bin is in place and ice maker arm is down.

After freezer section reaches between 0° to 2°F (-18 0 to

-t7 ° C), ice maker fills with

water and begins operating. Allow approximately 24 hours after installation to

receive first harvest of ice Discard ice created within first 12 hours of operation to

verify system is flushed of impurities

Operating Instructions

Confirm ice bin is in place and ice maker arm is down

After freezer section reaches O° to 2°F (-18 ° to -t7 ° C),

ice maker fills with water and begins operating You will have a

complete harvest of ice approximately every 3 hours

Stop ice production by raising ice maker arm until click is heard

Ice maker will remain in the off position until arm is pushed down

D rawe rs

Freezer Basket

To remove and install basket:

• To remove, lift front of basket and pull out to its full

extension Lift up front of

basket and remove

. To install, slide basket into rails at bottom of freezer

section Lift up front of basket, and elide to the back of unit

Ice Storage Bin

The ice storage bin is located below the automatic dispensing ice maker

TO remove and install ice storage bin: I_

• TO remove bin, remove ice cream shelf I] "':'_ ....

Ra se ce maker arm tO deactivate ice ]I _'\ maker Lift front of bin and pull out _

to its full extension. Lift up front of " -r_ bin and remove

• To install, slide bin into rails below ice maker until bin locks into place Drop ice maker arm to activate ice

maker, and replace ice cream shelf

IMPORTANT: Ice bin must be

ice dispensing, If freezer door

Iocked in proper place for proper ,_ ,_ _ does not close, bin is not in proper

location Turn auger driver counterclockwise (as shown) to properly align ice bin with back of unit.

Shelves

.............................. m

mm =m= Hm4=

Freezer Shelf

To remove and install clip-mounted shelves:

To remove, pull shelf from wall _ A mounting clips and pull left side _'_x_.l_- of shelf out of wall mounting

holes _

• To install, place shelf in mounting hole and attach to wall mounting clips

To remove

• To remove, snap dght side of

shelf from cabinet railing and remove from wall mounting

clips To install, replace shelf in

wall mounting clips Be sure back edge of shelf is flush with back of cabinet and snap shelf into cabinet

railing

................................ .#

Door Storage

Door Buckets

Refer to refrigerator section for instructions

Dispenser Features

, , i i iii iii i,

Dispenser Light ,ot sZ,o,,,,_

A light activates within the dispenser area at full power when dispensing ice or water

Dispenser Pad

The dispenser pad is located on the back wall of the dispensing area. When the dispenser pad is pressed, the selection chosen on your dispenser control panel will dispense

Removable Tray

The removable tray at the bottom of the dispenser area is designed to collect small spills and may be easily removed for cleaning and emptying purposes

IMPORTANT: Removable tray does not drain Continuous water running into tray will cause tray to overflow

t ..........................

e--

Water Dispenser Operation

A cAuv,oN I

To avoid personal injury or property damage, observe following instructions:

• Do not put fingers, hands, or any foreign object into dispenser opening

• Do not use sharp objects to break ice

• Do not dispense ice directly into thin glass, fine china, or delicate crystal

NOTE: During initial use of water dispenser, there will be a I to 2 minute delay while water tank fiils before water dispenses Discard first t0-14 containers of water after initially connecting

re[dgerator to household water supply and after extended periods of nonuse To use dispenser pad:

. Choose water selection from dispenser control panel

• Press sturdy, wide-mouthed container against dispenser pad., When dispensing crushed ice. hold container as close [o chute as possible to reduce spraying

• Release pressure on dispenser pad to stop water from dispensing A small amount of water may continue to dispense, and collect in dispenser tray Large spills should be wiped dry,

Five-Button Centre! Features

G_d

Dispenser Features

RLTER

DESPENSER FILTERED ICE & WATER LIGHT

Dispenser Operation _

To dispense:

• Select CUBE, CRUSH, or WATER mode by pushing button on dispenser control panel A green indicator light above

button shows mode se{ectien Press container against dispenser pad Selection mode may not be changed while ice dispenser is in operation,

NOTE: If water dispenser is continuously active for more than 5 minutes, an automatic lock out sensor witl shut down power to dispenser area. For instructions on how to unlock your dispenser, see the section entitled "Dispenser Lock" below.,

i i i i n II i nlnulluun

r Dispenser Lock _

This feature prevents ice or water from being dispensed L_

/ To lock and unlock dispenser: / To _ock dispenser, press and held LOCK/UNLOCK button for 3 seconds, A green indicator light above button confirms

dispenser is locked

L To unlock dispenser, hold LOCK/UNLOCK button for 3 seconds, Green indicator light above button will go out ..

r Filter Status indicator Light

/ The filter status indicator light serves as a reminder to replace the water tilter. A green light indicates that the / titter is in good condition A red light indicates the filter should be changed Once light turns red, it wiii remain o Good

red until function is reset,

/ To reset indicator: I " Press end hold both LOCK/UNLOCK and WATER buttons simultaneously for 4 seconds. The green filter FILTER

L status Indicator light will flash 3 times when the function has successfully reset.

_1 ilnlnulU nlHl'l ................................................... ,_1

Change

Auto Light _-

The auto light function offers the ability to activate the dispenser Iight at half-power when the .G,,_

LIGHT SENSOR detects that the Iight levels in room are low

o activate and deactivate auto light:

To activate, press ONIOFF button located on control panel A green NOTE: Dispenser light will operate whether

. ind{cator light above button displays to show that sensor is active, or not auto light is se{ected

To deactivate, press ON/OFF button Green indicator light will go out

Sabbath Mode

This mode is intended to deactivate power to the LED and dispenser lights, whiJe allowing the controls to remain operational

To activate and deactivate Sabbath Mode:

• ' To activate, press and hold beth LOCK!UNLOCK and ON/OFF buttons simultaneously for 3 to 4 seconds After 3 to 4 seconds, the LED and dispenser

lights will turn off Dispenser light will not activate during dispensing while in this mode.

To deactivate, press and hold both LOCK/UNLOCK and ON/OFF buttons simultaneously for 3 to 4 seconds After 3 to 4 seconds, the LED and dispenser lights witl activate

NOTE: In the event that power is interrupted while the Sabbath Mode

is active, the control will remain in Sabbath Mode when power returns,

Dispenser Features

Electronic Control Features

DISPENSER L]GITT

ii iiiiiii1,1

Dispenser Operation

To dispense water: To dispense ice:

Select the

• Press container against ° Press the _ button for crushed ice

dispenser pad.

button, " Select the _ button for cubed ice

Press container against dispenser pad

1 /

NOTE: ff water dispenser is continuously ac_e for more than 2 minutes, an automatic lock out

sensor w;ll shut down power to dispenser area, For instm_ons on how to unlock your dispenser,

see the section entJUed"Dispenser Lock" below.

This feature prevents ice or water from being dispensed

Dispenser Lock @

i ii iiiii i i iiiilllllll •

To lock and unlock dispenser:

To lock dispenser, press and hold the _ button for 3 seconds. A green indicator light

above button confirms

dispenser is locked

To unlock

ii i iii ii iiiiiiii1,11,11111, _ i iiiii ..................................

dispenser,

hold the

]_! button for 3 seconds Green indicator light above button will go ouL

iii ii iiii iiiii iii i,ii1,1,11iii, iiiii1,11 •

Light Function _uG"_

The light function offers offers two settings: OFF and AUTO NOTE: Dispenser light will operate at full power [ON_'DF_I The OFF setting wilt turn off the dispenser cavity light, when ice or water functions are in use. _ © ,_.'_0%

The AUTO setting allows the SENSOR to measure the surrounding light levels and adjust the power of the cavity light

accordingly. When the senser registers lower light levels (night lime, darkened kitchen), the cavity light will respond at 50% power, When the senser registers high light levels (lighted kitchen, direct sunlighl), the cavity light will not activate.

To activate auto setting: To deactivate light:

Press the _1'_"1 button located on contro_ne] Press the L"% button located on control panel Green To activate the AUTO setting, press the _ button_ indicator light above button will go out

When the green indicator light above the button display is on, the cavity dispenser light wil! use the AUTO setting

The filter status indicator light serVes as a reminder to replace the water filter. A green light indicates that the _ooD filter is in good condition., A red light indicates the filter should be changed Once light turns red, it will remain c._Gec:, red until function is reset.

To reset indicator:

Filter Status Indicator Light FILTER

• Press and hold both the _ and the L_,,_"_ buttons simultaneously for 4 seconds The green light will flash 3 times when the function has successfully reset,

These keys wi!l lower or raise the freezer or fresh food

Temperature Keys

compartment temperature,

r_ r_

i iii ii i i1,11i iiii iiii ii i1,111,11,11i1,,111,1,11 i,ii i#

i i ii iiii iiiiillll iiilllll,l,,llllllll iii

filter status indicator

i i ii i i i ii iii iiiiiiiiii

iii iii iiiii1,111iii

i iii i iiiiii ................. ii i ii i

NOTE: See the section Hew to Adjust the Temperature Controls for instnJctions on how to set food oompartment

temperatures

Lii _,llll,lll

Electronic Control Features o.e, ue

Dispenser Features

OFF

(3N

DISPENSER LIGHT

Max Cool

This function causes the fresh food temperature to drop to the minimum refrigerator

temperature setting available, This setting remains in effect for approximately 10 hours,.

To activate and deactivate Max Cool:

To activate, press the [_ button The green light above the button will indicate

active status To deactivate, press the @ button The green light above the button will go out

.................. i

Max Freeze

This function causes the freezer temperature to drop to the minimum freezer temperature setting available This setting remains in effect for approximately 24

hours

To activate and deactivate Max Freeze:

To activate, active status

the _ button, The green light above the button will indicate

press

changed if Max Cool or Max Freeze setting is active

NOTE:Th 'em e a uresett'n nn°tbel

i ii HiHimm,iHHm,,nl,,,n -,1

NOTE: The temperature setting cannot

be changed if Max Cool or Max Freeze setting is active

To deactivate, press the _ button,, The green light above the button will go out,

Display OnlOff

The Display On/Off switch controfs power to the LED display To activate and deactivate display:

• To activate, press the _ button The display will light,

• To deactivate, press the _ button The display wilt go out

This key, if enabled, causes less frequent defrost cycles This conserves energy To activate and deactivate Vacation Mode:

• To activate, press the button The green light above the button wilt indicate active status

Vacation Mode

• To deactivate, press the _ button, or open either refrigerator

Alarm Off

This key is used to rum the Ht TEMP Waming Indicator and audio alarm, as well as the OPEN DOOR audio alarm off This will also deactivate

alarms presently in progress.

i i numm,HnHH,mH

door

imn HHI ,HnmH

n :::::::::::::::::::::::::::::::

i i,n,,n

i i H in iiiiirlrlrlllrllll,,,i.lU

To turn the alarm off:

Press the @ button,

Dispenser Features

Hidden Electronic Control Features

I Sabbath Mode _ F<_-_ "

This mode is intended to deactivate power to the LED and dispenser lights, while allowing the I_l +l °N:°FF I controls to remain operational No visual or audio alarms will be available while in this mode, _

To activate and deactivate Sabbath Mode:

. _ _ NOTE: In the event that power

To activate, press and hold both the _ and _ buttons simultaneously for 3 is interrupted while the Sabbath

seconds After 3 seconds, the LED and dispenser I_ghts wilt turn off Dispenser hght remain in Sabbath Mode when

will not activate during dispensing while in this mode° power returns

/ " To deactivate, press and hold both _ and _ buttons simultaneously for 3

L seconds, After 3 seconds, the LED and dispenser lights will activate.

Auto Display

The auto display controls the illumination of the LED display based on the light readings received from the SENSOR If the SENSOR indicates tow light levels, the display wilt be dimmer than if displaying during well-lit pedods.

To set the power level of the _splay:

• Press and hold both the _ button and the freezer =v button for 3 seconds The current active state will show in the display by using AL O for on, AL A for auto NOTE:The letters AL will always show in freezer

_ . . , Mode is active, the control will

i Use the refrigerator ...... button to scroll through the display states temperature display while in this mode.

Activate the chosen setting by pressing the

ii, ii i ................. lilt1

This mode is available to change the temperature display between Fahrenheit and Celsius,

To change current temp:rature reading:

Temperature Conversion Mode

• Press the @ and _4. buttons simultaneously for 3 seconds.

button,

i i iii iii ii ii

Hidden Lockout for Upper Keypad

The purpose of this mode is to prevent tampering with the upper set of dispenser controls. This includes the Display OnlOff, Max Freeze, Max Cool, Vacation Mode, and Temperature Set

functions

To activate and deactivate Hidden Dispenser Lockout:

seconds,,

To activate, press the _ and @ buttons simultaneously

To deactivate, press lhe @ and @ buttons simultaneously

for 3

for 3 seconds,

ON/OFF Function

The ONfOFF function turns off cooling to the fresh food and

freezer sections while allowing the lights and electronic display to stay on The dispenser functions will not be

available while in this mode

To deactivate and activate unit:

To deactivate, press the freezer _ button until the readout registers beyond the maximum allowable freezer temperature, At this point, the

LED will read OFF Press the _ button to confirm the selection

- To reactivate, press the freezer .'2".button, Press the confirm the selection.

" WARNING

TO avoid electricai shock wNch can cause severe personal injury or death, do not perform maintenance or service on

refrigerator unless unit is unplugged.

NOTE: After reactivaUon, the display ,MII show temperature setting previously in

use See the section How to Adjust the Temperature Controls for instructions

button to

on how to set food compartment temperature&.

oF °C

How to Clean Your Unit

[ WARNING

To avoid electrica{ shock which can cause severe personal injury or death, disconnect power to refrigerator before cleaning. After cleaning, connect power,

1 CAUTION l

TO avoid personal injury or property damage:

, Read and follow mantJfacturer's directions for all cleaning products,

• Do not place buckets, shelves, or accessories in dishwasher Cracking or warping of accessories may result

AREA

ii ,ill

Textured Doors and Exterior

Cabinet interior

Stainless Steel Doors

and ExteHor_

IMPORTANT:

Damage to stainless steel finistI due to improper use of cleaning products or

non.recommended products is not covered

under any warranty

Dispenser Controls

Door Gaskets

Condenser Coil Remove

roe grille to aecez;s

Condenser Fan Outlet

Grille

See back of refrigerator

Accessories Sbefv,es, buckets, drm_trs, ete

DONOT USE

I III 11111

? Abrasive or harsh cleaners

? Ammonta ? Chledne bleach

? Concentrated detergents or

solvents

? Metalor plastic-textured

scouring pads

? Abrastve or harsh cleaners ? Ammonia

? Chlorine bleach ? Concentrated detergents or

solvents

? Metat or plastic-textured

scouting pads ? Vinegar-based product ? Citrus-based cleaners

? Abrasive or harsh cleaners ? Ammonia

? Chlorine bleach ? Concentrated detergents or

solvents

? Metal or ptasUc4extured

scoudng pads

? Abrasive or harsh cleaners ? Metal or plastic4extured

seoudngpads

N/A

? A Dishwasher

DO, o,

? use 4 tablespoons of

baking soda dissolved In 1 quart (1 liter) warm soapy

water

? Rinse surfaces with clean

warm water and dry

immediately to avoid water spots

? Use warm, soapy water and

a soft, clean cloth or sponge

? Rinse surfaces with clean

warm water and dry Immediately to avoid water

spots

? Use a vacuum cleaner hose

.......nozzle

? Use a vacuum cleaner hose

nozzle with brush attachment,

? Foliow removal and

_nsla_lattoninstructions from appropriate feature section.

? Allow items to adjust to

room temperature,

? Dilute mild detergent and

use a soft clean cloth or sponge for cleaning

? Use a plastic bristle brush

to get into crevices

? Rinse surfaces with clean

warm mater

? Dryglass and clear items

immediately to avotd spots

Hints and Care

How do I remove __z_._/(_

o o,

refrigerator?

j 1, Remove air food

2, Disconnect power from refrigerator 3 Clean the following items using the

appropdate instructions in How to

Clean Your Un#:

• Walls, floor, and ceiling of cabinet interior.

. Drawers, shelves, and gaskets.

4 Pay special attention to all creviceswtwg

by completing the following steps:

• Dilute mild detergent and brush solution into crevices using a

plastic bristle brush., I_

• Let stand for 5 minutes . Rinse surfaces with warm water. ,aA

Dry surfaces with a soft, clean cloth,, X

5 Wash and dry all bottles,

containers, and jars Discard spoiled or expired items.

6 Wrap or store odor-causing foods in

tightly-sealed containers to prevent reoccurring odors

7 Connect power to refrigerator and

return food to unit

8 After 24 hours, check if odor has

been eliminated

tf odor is sti)t present .1

I Remove drawers and place on top

shelf of refrigerator,

2 Pack refrigerator and freezer

sections-including doors-with crumpled sheets of black and white newspaper

3, Place charcoal briquettes randomty

on crumpled newspaper in both freezer and refrigerator compartments°

4 Close doors and let stand 24-48

hours 5, Repeat steps 5 through 7 tf odor was not eliminated, contact

Sears Service Center Refer to back of manual for phone number,

" A stainless steel cleaner has been included inside the refrigerator for your use To purchase

additional cleaner, please contact Sears using the information on the back of your manual

Hints and Care

How to Get the

Most Out of Your Energy

Dollar

• Avoid overcrowding refrigerator shelves This reduces effectivity of air circulation around food and

causes refrigerator to run longer

• Avoid adding too much warm food to unit at one time, This overloads

compartments and slows rate of cooling

• Do not use aluminum foil, wax

paper, or paper toweling as shelf liners This decreases air flow and

causes unit to run less efficiently

• A freezer that is 21afu{t runs most

efficientfy

• Locate refrigerator in coolest part of room, Avoid areas of direct sunlight,

or near heating ducts, registers, or other heat producing appliances If

this is not possible, isolate exterior by using a section of cabinet or an

added layer of insulation

• Refer to this Use and Care Guide section on temperature controls for

recommended control settings

m Clean door gaskets every three

months according to this Use and

Care Guide's cleaning instructions

This wilt assure that door seals

property and unit runs efficiently

• Take time to organize items in

refrigerator to reduce time that door is open.

. Be sure your doors are closing

secure{y by feveling unit as" instructed in this Use and Care

Guide,

• Clean condenser coils as indicated

in the Use and Care Guide every 3 months This will increase energy

efficiency and cooling performance,

How to Remove and Replace Light Bulbs

[ WARNING I

To avoid electrical shock which can cause severe personal injury or death, disconnect power to refrigerator before replacing Iight bulb After replacing tight

bulb, connect power

[ CAUTION ]

To avoid personal injury or property damage, observe the following:

• Allow light bulb to coot

• Wear gloves when replacing light bulb

Upper refrigerator section

1, Locate finger gaps on each side of clear light _"-'_o_T_

shield Insert fingers and press in on each side of shield Pull shield down and remove

2, Remove light bulbs 3, Replace with appliance bulbs no greater than

40 watts.

4 Replace light bulb cover by inserting front tabs of (.-_ r,'r "t _.__/

light shield into slots direcUy in fronl of light assembly,

.wJl ,=d

n i nUllllln,,u,,

Lower refrigerator section

Pinch bottom tabs (A) on light cover and pull straight out

2 Remove light bulb,

3. Replace butb with appliance bulb no greater than 40

watts.

4 Insert top tabs (13) of tight cover into liner slots and

snap bottom portion over Iight assemb{y

1, Remove ice bin by tifting front of bin and puiting out .._i_---.....,

2 Remove lightbulb cover by pinchingtop tab (A) and I!"_ _ _h_'_I

pulling cover out, V.t::_I\ _ /1_=_

3 Remove tight bulb Replace with appliance butb {_V k-_

no greater than 40 wafts. ".-._v.._.7

4- Insert bottom tab (13) of light cover into liner slots and snap

" Freezer section A

top portion over light assembly

5. Repface ice bin by sliding in until bin locks into piece

i i innnnn, n u nnlUn,u i ,nlii, ,,,,i,u,,,,u,,i

Today's refrigerators have new features, such as foam insulation, and are more energy efficient than past refrigerators Foam insulation is veq/energy efficient and has excellent insulating capabilities; however, it is

NOISE

),.',,(_ not as sound absorbent as former insulating materials As a result, cedain sounds may be unfamiliar In time,

these sounds will become familiar Please refer to this information before calling service

TOPIC POSSIBI_ CAUSE SOLUTION

................ : ........ 77 : ..................

" Freezer centre} (,4) clicks when starling or NormaI operation

Clicking

Air rushing or

whirring

Gurgling or boiling sound

Thumping

Vibrating noise

Buzzing

Humming

stopping compressor.

Defrost timer or electric damper control (some

models) (B) sounds like an electric clock and

makes an occasional click or snap Condenser fan (D) makes this noise white

operating. Freezer fan (C) makes this noise while

operating, Freezer fan (C) slows to a stop as the freezer

dooris opened, Evaporator (E) and heat exchanger (F)

refrigerant make this noise when tIowing. lee cubes from ice maker drop into ice bucket

'G):

Dispenser ice chute (H} closing. Compressor {I) makes a pulsating sound while

running.

Refrigerator is not level Ice maker water valve (J) hookup buzzes

when Ice maker fills with water.

lee maker (K) is in the 'on' position without water connection

Ice auger (L) hums as auger agitates ice during dispensing.

Compressor (I) can make a high pitched hum while operating.

Solenoid valve (M) operating ice chute door

Normal operation

Norma_ operation

Normal operation

NormaI operation

Normal operation Normal operation

Normal operation See leveling instructions tn

"Installing Your Refrigerator"

Normal operation Stop sound by raising ice

maker arm to 'off' position See ice maker section in

"Freezer Features" for details. Normal operation

Normal operation

Troubleshooting

OPERATION _o>"_

Freezer control and lights are on, but

compressors are not

operating.

Environment- controlled drawers

are too warm

Refrigerator does not operate

Refrigerator still Unit is malfunctioning won't operate

Electronic controls Controls have detected functional problems (some models) read and will attempt lo regulate temperature unlit Contact service for assistance

EO, ES, or ERROR service is obtained in display,

Temperature of food is too cold

Refrigerator is in defrost mode Refrigerator with digital temperature controi

has just been plugged in

;ontrolsettings are too low.

Freezer controls are set too low

Drawer is improperly positioned

Refrigerator is not plugged in. Dial control in freezer is set to off (some

models). Electronic temperature controls (some

models) have been turned off.

-'use is blown, or circuit breaker needs to be

reseL Power outage has occurred

Condenser coiis are dirty.

_Refffgerator or freezer controls are set too

high

Normal operation Wait 40 minutes to see if unit restarts

Normal operation Wait 60 seconds to see if unit starts See drawer section in"Refrigerator Features" to adjust controls.

See temperature controls section in "lnstafting Your Refrigerator" to adjust your controls.

See drawer section in "Refrigerator Features" to propedy install drawers Plug in unlt.

See dial temperature controls section in"Installing Your Refrigerator" to adjust your controls,

See hidden electronic control section under =Dispenser Features"

Replace any blown fuses Check circuit breaker and reset if necessary

Cati local power company listing to report outage.

Unplug refrigerator and transfer food to another unit If another unit is not

available, place dry Ice in freezer section to preserve food Warranty does not cover food loss. Contact service for assistance.

Clean according to cleaning instructions in "Hints and Care". See temperature controls section tn "installing Your Refrigerator" to

adjust your controls

Troubleshooting

OPERATION_

i1,1i,i iii i, i,i ii

TOPIC

Food temperature

appears too warm

Refrigerator has an Compailment is dirty or has odor-causing food Refer to odor removal section in _Hints and Care"

odor

Water droplets form on outside of refrigerator Door gaskets are not sealing properly.

Water droplets form on Humidity levels are high or door has been inside of refrigerator, opened frequently,

Refrigerator or ice maker make unfamiliar sounds or seems too

loud,

Temperature- controlled meat drawer

and/or crisper drawer do not close freely.

Refrigerator runs too frequently,

POSSIBLE CAUSE

nnnlllun,nul,n,l,, u,

Door is not closing property

Door gaskets are not sealing properly

Conkols need to be adjusted Condenser coils are dirty.

Rear air grille is blocked

Door has been opened frequently, or has been opened for long pedods of time

Food has recently been added

Door is not closing properly

....Humidity levels are high.

Controls require adjustment

D.Doorgaskets are not sealing properly.

Normal operation

Contents of drawer, or positioning of items in the surrounding compartment could be obstructing drawer

Drawer is not in proper position Refrigerator isnot level

Drawer channels are dirty or need treatment.

Doors have been opened frequently or have been opened for tong periods of time

Humidity or heat in surrounding area is high.

Food has recently been added Unit is exposed to heat by environment or by

appliances nearby. Condenser coils are dirty Controls need to be adjusted

Door is not closing properly

Door gaskets are not sealing properly

SOLUTION

See teveting instruc0ens in "Installing Your Refrigerator". Check for tntemaf obstructions that are keeping door from

closing propedy (i e improperlyclosed drawers, ice buckets, oversized or improperlystored containers or foodstuffs, etc.).

Clean according to cleaning instructions in "Hints and Care" See temperature controls section in qnstaIting Your

Refrigerator" to adjust your controls. Clean according to deanfng instructions_n"Hints and Care". Check the positioning of food items in refrigerator to make sure

grille is not blocked Rear air gdtie _slocated behind cdsper drawers,

Reduce lime door is open Organize feed items efficiently to

assure door is open for as short a lime as possible. Allow interior environment to adjust for period the door has

been open. Allow time for recently-added food to reach refdgerator or

freezer temperature.

Check for internal obstructionsthatare keeping door from

ctosingproperly (i e impropedy closed drawers, ice buckets. oversized or improperly stored containers or foodstuffs, etc.).

See ievaling Mstructions in "Installing Your Refrigerator". Clean according to cleaning instructions in "Hints and Care".

Normal dudng times of high humidity. See temperatura controls section in "installing Your

Refrigerator* to adjusl your controls, Reduce time door is open. Organize food items efficiently to

assure door is open for as short a time as possible. Clean accordin£ to cleaning instructions in "Hints and Care".

Refer to noise section of =Troubleshooting" for details

See drawer section in =Refrigerator Features" to properly install drawers

See leveling instructions in "installing Your Refrigerator". Apply a thin layer of petroleum jetfy to drawer channels.

Reduce time door is open Organize food items efficiently to assure door is open for as short a lime as possible.

Ailow interior environment to adjust for period the door has been open,

Normal operation AlIow time for recently-added food to reach refrigerator or

freezer temperature,

Evaluate your unit's environment See location selection section in "installing Your Refrigerator".

Clean according to cleaning instructions In "Hints and Care". See temperature controls section in "installing Your

Refrigerator" to adjust your controls. See leveling instructions in "installing Your Refrigerator". Check for internal obstructions that are keeping door from

closing propedy (i e improperly closed drawers, ice buckets. oversized or improperly stored containers or foodstuffs, etc.).

Clean according to cleaning instructions in"Hints and Care"

0PERATION_(cont_nued)

1,,,,r,,,

TOPIC POSSIBLE CAUSE

Troubleshooting

SOLUTION

Refrigerator runs too Controls need to be adjusted frequently (continuedJ

Door is not ciosMg properly

U '! !11 rr..r.n_,,

Water appears cloudy

Particles in water andlor lce Carbon dust from water filter cadddge cubes_

No Indicator lights are tit on Freezer door is not closed dispenser control (some

models) Refrigerator Isnot plugged in.

Neither Ice nor water ts Freezer door Isnot closed dispensed when pads are

pushed (some models) Controls are In lock mode.

Air or air bubbles In water

Concentrations of minerals In water will form padlcleswhen water becomes frozen and

melts.

Fuse is Nown. or circuit breaker needs to be reset.

Power outage has occurred. Refrigerator is in Sabbath Mode.

Water tank Is filling

Ice maker or ice maker-equipped unit has just recently been installed or a large amount of Ice

has just been used. Water filter iscloggedor needs to be changed

Ice maker Is not producing enough ice or ice Is malformed

(some models)

lee maker has just recently been installed or a largo amount of Ice hasjust been used.

Water pressure is too tow

Water filteriscloggedor needs to be changed.

Ice maker is not producing Ice

Ice maker arm Is nottn correct positton

(some models)

Household water supply Isnot reaching water

vaive

Copper or plastic tubing has kinks

Water pressure ts too _ow

Check freezer temperature

lee bin Ix not {nstalled properly

See controls section in chapter called Installing Your Refrigerator On how to adjust your controls,

Refrigerator is not revel See chapter called Installation Instructions for detaits on how to level your unit,

Check for Internal obstructions that are keeping door from closing properly (I e improperly closed drawers, ice buckets, oversized or Improperly stored containers or foodstuffs, etc.).

Check gaskets for proper sen See cteaning guide in chapter called Hints and Care on how to c_ean gaskets,

This ts normal when first using dispenser and will disappear r

with use. '=

Initialwater ejected through cartridge may contain harmless _A carbon dust flushed from cadridge, Particles ere safe for

eonsumption_ Will disappear after the first few uses. Pedlcles are not harmful and naturally occur In water supplies

Verify that freezer door is closed Power is removed from the controf when freezer door Is opened.

Plug In unit. Replace any blown fuses Check circuit breakers for any

trippedcircuits,

Call local power company Ilsting to report outage. See Dispenser Features section for lumber information.

Verify that [reezer door is closed Power ts removed from the eoata31 when freezer door Is opened.

See Dispenser Features section for further Information.

At InltMl use. there Is an approximate 45-second delay In dispensing wNle the Internal water tank Is filling,

Watt 24 hours for Ice production to begin end for Ice maker to

restock after emptied

Change water filter Wait 24 hours for ice production to begin and for ice maker to

restock after emptied, Lowwater pressure can cause valve toleak Water pressure

must be between 20 to t00 poundsper square Inch to function propedyA m_ntmumpressureof 35 pounds per square inch_s

recommended for unitswith waterfilters,

Change water fitter. Confirm Ice maker arm ts drown See Freezer Features section

In your owner's manual for details. Check water connection procedure In your Installation

Instructions.

Turn off water suppty and remove kinks If kinks cannot be removed, replace tubing.

Water pressure must be between 20 to 100 pounds per square Inch to function property A minimum pressure of 35 pounds per square Inch ts recommended for unite with water filters.

See the controls section In your owner's manual for assistance on how to adjust your controls Freezer must be between 0 to 2"F (-18 to-17"C) to produce Icm

See Ice bin section for proper Installation and alignment

ago

Troubleshooting

TOPIC

Water appears cloudy

Particles in water andlor ice

cubes°

No indicator lights are lit on dispenser

Neither ice nor water is dispensed when pads are

pushed

Ice maker is not producing enough ice or lee Is

malformed

Ice maker is not producing

Ice

POSSIBLE CAUSE

Air or air bubbles in water

Carbon dust from water filter cartridge

Concentrations of minerals in water will form

3a_cles when water becomes frozen and

mells. Freezer door is not dosed

Refrigerator is not plugged In, Fuse is blown, or circuit breaker needs to be

reset. Power outage has occurred

Freezer door is not closed Controls are in lock mode,

Water tank istilting Ice maker or ice maker-equipped unit has

just recently been installed or a large amount

of ice has just been used. Water filter is dogged or needs in be Change water filter

changed,

Ice maker has just recently been installed or Wait 24 hours for Ice production to begin and for ice maker a fargo amount of ice has just been used. in restock after emptied.

Water pressure is too low inch in function properly.A minimum pressure of 35

Water filter is clogged or needs to be Change water filter changed.

Household water supply Is not reaching water valve

Copper or plasfic tubing has kinks

Water pressure is too tow

Check freezer temperature

Ice bln is not installed property

Improper water valve was installed

SOLUTION

This is normal when first using dispenser and wilt

disappear with use.

lnitia_water ejected through cartridge may contain harmless carbon dust flushed from cartridge Particles are safe for consumption Will disappear after the first few

USES,

Pa_cles are not harmfut and naturally occur in water

supplies Verify that freezer door is closed Power is removed from

the control when freezer door is opened.

Plug in unit,

Replace any blown fuses Check circuit breakers for any

tdpped circuits,

Call local power company listing to report outage,

Vedfy that freezer door tsdosed Power is removed from

the control ,when freezer door is opened,

See controlinstructions in "Dispenser Features" At initial use, there Is an approximate 45-second delay in

dispensing while the internal water lank ts filling.

Wait 24 hours for ice production in begin end for ice maker

to restock after emptied.

Low water pressure can cause valve to leak Water

pressure must be between 20 to !00 pounds per square

pounds per square inch is recommended for units with

water filters.

Check water connection procedure written in"Installing

Your Refrigerator".

Turn off water supply and remove kinks If kinks cannot be

removed, replace tubing,

Water pressure must be between 20 to "iO0pounds per

square inch to function properly A minimum pressure of 35

pounds per square inch is recommended for units with

water filters,

See temperature controls section in "Instafling Your

Refrigerator" to adjust your controls Freezer must be

between 0 to 2°F (-18 to -17°C) to produce ice,

See ice bin section for proper installation and elignmenh

Check water connection procedure written in "Installing

Your Refrigerator" Setf-pierdng and _t_e"saddle valves

cause low water pressure and may dog the fine over time

Sears is not responsible for property damage due to

improper installation or water connection,

+ 53 hidden pages

Kenmore 596.50019100 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual