Owner's Manual
Dehumidifier
_53.
Models 5030 00o
CAUTION'.
Before using this dehumidifier,
read this manual and follow all
its Safety Rules and Operating
Instructions.
Sears, Roebuck and Co., Hoffman Estates, IL 60179 USA
P/N 327000010(0002)
° Safety
= Operation
o Care and Cleaning
o Troubleshooting
o Espa5ol
o Frangais
Table of Contents
Product Registration 2
Important Safety Instructions 2
Location 3
How It Works 3
Operating Steps 3
Dehumidifier Features 3_5
Removing Collected Water 5
Troubleshooting 6
Warranty 7
Sears Service 7-8
Espa_ot 9
Fran_ais I7
Product Registration
Important Safety
nnstructions
Avoid fire hazard or
electric shocL Do not use an extension
cord or an adaptor plug Do not remove
grounding prong from power cord..
Grounding type
wall receptacle
the
Power supply
cord with 3-prong
grounding plug
Record Your Model and Serial Number
In the space provided below record the model and serial number of your
dehumidifier,, You will find them on the nameplate located in the center of the rear
panel, behind the bucket
Model Number:
Serial Number:
Purchase Date:
Read all instructions before using this dehumidifier. To reduce the risk of fire,
electric shock, or injury to persons when using your dehumidifier, follow basic
precautions, including the following:
For Your Safety
Do not store or use gasoline or other flammable vapors and liquids in the vicinity of
this or any other appliance, Readproduct labels for flammability and other warnings
Child Safety Precautions
• Destroy the carton, plastic bags, and any packing materials immediately after the
dehumidifier is unpacked, Children should never use these items for play
• Do not leave children unattended in an area where the appliance is operating,.
Do not allow them to sit or stand on the appliance,
Electrical Information
o
Foryour safety and protection, this dehumidifier is equipped with a three-prong
grounding plug on the power cord, Do not, under any circumstances, cut or
remove the round ground prong from the plug.
o Your dehumidifier must be plugged directly into a properly grounded and
polarized three-prong receptacle. If the wal! receptacle you intend to use wilt not
accept a three-prong plug, or if you are not sure the outlet is adequately
grounded or protected by a time delay fuse or circuit breaker, have a qualified
electrician install the proper outlet according to the National Electrical Code and
applicable local codes and ordinances. Do not use an extension cord or an
adapter plug.
= Never unplug the dehumidifier by pulling on the power cord Always grip the
plug firmly and pull straight out from the receptacle.
o Do not pinch, bend, or knot the power cord,.
Read and Save These
nnstructions
Operate dehumidifier only as instructed in this Owner's Guide, These instructions
are not meant to cover every possible condition and situation that may occur,.
Common sense and caution must be used when installing, operating, and
maintaining any appliance
Printed in U SA
Location
How It Works
Selecting a Location
IMPORTANT:
1 Dehumidifier must be operated in an enclosed area to be most effective, Close
all doors, windows, and other outside openings to the room.
2, Be sure not to obstruct the air flow through the front grille or out of the louvers
on the left side,
,
A dehumidifier operating in a basement will have little or no effect in drying an
adjacent enclosed storage area, such as a closet, unless there is adequate
circulation of air in and out of the area..It may be necessaryto install a second
dehumidifier in the enclosed area for satisfactory drying.
When the unit is started, the fan begins to pull moisture-laden air across the
dehumidifying coils The coils condense or draw moisture from the air, and air flows
through the side louvers into the room as dry, warm air. Moisture removed from air
is collected in a bucket on the front of the dehumidifier,,
NOTE: This unit is equipped with Electronic Control Protection. There is a 2 minute
delayed start after one of the following occurs:
. The bucket is removed
= Dehumidifier Level changes
Operating Steps To begin operating the dehumidifier, follow these steps:
I Plug the power cord into a properly grounded 1101120 volt AC outlet
Note: Before operating this unit, see the "Removing Collected Water" section
for proper placement of the bucket Models will not operate if the bucket is not
properly positioned
2. When first using the dehumidifier, set the control to the MAX.DRY position The
unit will run continuously at this setting
Note: The dehumidifier should be kept in operation as long as excess moisture
is present in the room air
3. Set Fan Speedto HI. The HI setting is recommended for faster moisture removal
4. Allow the dehumidifier to operate at the above settings for three to four days.
After this time, adjust the controls as needed See below.
Electronically Controlled Dehumidifier Operating Instructions
ON/
OFi
TO
CONTROL FULL
DEGREEOF BUCKET
DEHUMIDIFICATION LIGHT
DEBUMIDIFICATION _
ON/
TO
CONTROL _ FULL
DEGREEOF ili!!iilBUCKET
'_ili!!!iiLIGHT
Pleasefamiliarize yourself with the Control Panelbefore you begin Your Dehumidifier can be operated from 15% MAX to 75%
MIN Relative Humidity, at either High or Low Speed (except 5030),
ElectronicalJy Controlled Dehumidifier Operating instructions (continued)
TO TURN UNIT ON:
Press
Pad
Note: Each time you unplug the Dehumidifier or there isa power interruption, the control will return to the last setting you hay
chosen This unit is equipped with Electronic Control Protection There is a 2 Pninute delayed start when some settings ar
changed.
TO CHANGE FAN SPEED: YOU WILL SEE:
Press
Fan Pad
YOU WILL SEE:
(Automatically on "HI" Speed.)
TO RAISE HUMIDITY SET POINT:
"A" Arrow
TO LOWER HUMIDITY SET POINT:
"V" Arrow
Press
Up
Press
Down
YOU WILL SEE:
Whichever you choose
1
YOU WILL SEE:
i
Whichever you choose
,
Note: When the down arrow "v" ispressed the unit will stop running if the level of dehumidification has been reached When
the room humidity increasesthe unit will start running again,,
4
Electronically Controlled Dehumidifier Operating Instructions (continued)
OTHER FEATURES:
When the water receptacle is full the "FULL" light will be lit and the unit wilt Shut-Off. This is the time to empty the bucket
(The Dehumidifier wilt not operate while the bucket is removed) Following emptying the accumulated water, replace the bucket
and the Dehumidifier wil! operate at the last setting chosen_
FULL BUCKET
Light
TO TURN DEHUMIDIFIER OFF
Press
ON/OFF
Pad
Dehumidifier Features
Moisture Removal
At first, the dehumidifier wilt remove large amounts of moisture tt will continue to
do so until the relative humidity is reduced to a point where moisture damage wilt
not occur Then, the amount of moisture removed from the air will be atot less,This
indicates the dehumidifier is operating effectively and is maintaining the relative
humidity at the desired level..Judge the performance of the dehumidifier by the
elimination of dampness and dampness odors, not by the amount of water being
deposited in the bucket When bucket has filled with water, unit will turn off. All
models feature an Automatic Shut-Off light that will glow unti! bucket is emptied
and returned to the proper position
Operating Conditions
A dehumidifier wilt not operate satisfactorily if room temperature is 65°F (18°C) or
lower, or if the humidity in the room is low Under these conditions, the
dehumidifier should be turned off
A dehumidifier wifl not eliminate frost on windows during winter, The
dehumidifying coil normally operates above freezing temperatures and cannot
prevent moisture from condensing on the inside of a window pane that is below
freezing.
TIP: tt may be helpful to use a dehumidifier in the kitchen or laundry area where
the humidity is high, Reducing humidity in these areas may reduce frost on
windows in other parts of the home
Dehumidifier Features
(continued)
Frost Control
The FrostContro! feature prevents frost or ice from remaining on the dehumidifying
coil for an extended period of time, When frost formation occurs, this control turns
off the compressor, The fan continues to run, causing any frost or ice to melt,,
Dehumidifier will then resume normal operation
Frost Control is also designed to prevent excessive on-off cycling Under certain
conditions this may allow frost to remain on coil for some time before the
compressor turns off and the frost iscleared
Removing Collected
Water
Figure 1
Bucket and Float Installation
All models are supplied with a bucket, which is conveniently tucked into the front
of the unit to accumulate water removed from the air, or use the built-in hose
connection to carry water directly to a drain.
VVhen using the bucket the Automatic Shut-Off switch is activated by a float The
Automatic Shut-Off switch stops the unit before the bucket overflows, and turns
the unit on again after the bucket isemptied and replaced
The bucket and float must be installed correctly for proper operation (Figure I)
Bucket Cleaning Instruction
Periodic cleaning with a mild detergent and water will prevent the growth of mold,
mi!dew and bacteria,
Remove bucket as shown in Figure 2
Direct Draining
If you want the water to flow directly to a drain, you must first remove the hose cap
(Figure 2) To remove hose cap, use a standard screwdriver and turn counter-
clockwise Connect any standard garden hose to the bucket connection, or
place the dehumidifier over the drain A standard garden hose has a 3/4"
(t9 ram) diameter connection with 11'¼2threads per inch
Note: When using either of the above direct draining methods, you must first drill
a 3/8" (I 0 mm) hole in the center of the bucket connection. (For ease of drilling use
locating mark to center drill bit for hole (Figure 3)) This will allow water to flow
freely through the connection To resea! the hose connection to the bucket, use any
standard hose end cap The hose cap cannot be used to reseal the hole.
Figure 2
Figure 3
Locating
Hole
IMPORTANT:
Do not drink
the water
collected in
the bucket.
Figure 4
6
Avoid Service Checklist
Before calling for service, review this problem occurrence list. It may save you time and expense, because some of the
occurrences are not the result of defects in materials or workmanship, and would not be covered by the warranty,
OCCURRENCE SOLUTION
DEHUMIDIFIER DOES NOT OPERATE° Electronic Contro! Protection, Bucket was removed or Dehumidifier Level has changed Please
wait 2 minutes for Dehumidifer to restart
Plug is disconnected from outlet Push plug firmly into wall outlet.
House fuse blown or circuit breaker tripped Replace fuse with time delay type or reset circuit
breaker.
The dryness level you selected has been reached Dehumidifier automatically shuts off when
selected amount of moisture has been removed from the air tf you want to remove more
moisture, set control to MAX DRY HI SPEEDAfter the dehumidifier starts, reset the control to the
desired setting
Bucket not installed properly See "Removing Co!lected Water"
Water in the bucket has reached its preset level Dehumidifier automatically turns off when this
occurs Empty bucket and return bucket to position
Dehumidifier is not turned on Press"ON" and set control to MAXDRY
DEHUMIDIFIER RUNS TOO MUCH. Windows or doors near dehumidifier are open to outdoors Close all windows or doors to outside
Area to be dehumidified is too large Check with your dealer to see if capacity is adequate
Air movement through dehumidifier is blocked Grill may be dirty Use brush attachment of
vacuum cleaner to clean grill Dehumidifier must be placed in a space that does not restrict air
flowing into the front grille or out of the louvers on the left side
Dehumidifier has been installed or restarted recently The higher the moisture in the room, the
longer the dehumidifier will operate
The Control is set at MAX DRY Dehumidifier will not turn off if the Control is at MAX DRY until
the room is very, very dry
DEHUMIDIFIER EMITS AN UNPLEASANTThe bucket is dirty Clean per instructions on page 6
ODOR.
DEHUMIDIFIER IS OPERATING BUT
ROOM iS NOT DRY ENOUGH°
FAN-LIKE NOISE°
Humidistat Control isset too low Set the Control to a higher setting
Dehumidifier has been installed or restarted recently The higher the moisture in the room air, the
longer it takes for the room air to become dry
Dehumidifier does not have sufficient clearance to operate Air flow to front grill is blocked See
"Selecting a Location," page 3
Room temperature is too low Unit will not operate satisfactorily if the room temperature is below
65°F (18°C) See "Operating Conditions," page 6
Refer to causes under DEHUMIDIFIERRUNSTOO MUCH
Air is moving through the dehumidifier This isa normal sound
Sears Dehumidifier
Warranty
Full One Year Warranty on Dehumidifier
For one year from date of purchase, if this Dehumidifier isoperated and maintained
according to the owner's instructions attached to or furnished with, the product,
Sears will repair this Dehumidifier free of charge, if defective in material or
workmanship..
Full Five Year Warranty on Sealed Refrigeration System
For five years from date of purchase, when this Dehumidifier is operated and
maintained according to owner's instructions attached to or furnished with the
product, Sears wilt repair the sealed refrigeration system (consisting of refrigerant,
connecting tubing, and compressor motor) free of charge, if defective in material
or workmanship,
Warranty Exclusions
1. Damage to product caused by misuse, fire, flood, acts of nature..
2 Damages due to commercial use or from product being used in multi-user
dwellings.
3. Damage to Sealed System* caused by salt corrosion or chemical reaction to
copper/steeL
*Sealed System(compressor, condenser, evaporator, drier and tubing)
Warrant,/Service
Warranty Service is available by returning this Dehumidifier to the nearest Sears
Service Center in the United States,
This warranty applies only while this Dehumidifier is used in the United States_
This warrant,/gives you specific legal rights, and you may also have other rights
which vary from state to state
Sears Roebuck and Co.
Dept. 817WA
Hoffman Estates, II, 60179
Sears Service
"We Service What We Sell" means your purchase has added value because you
can depend on Searsfor service,We have service centers nationwide, staffed with
professional technicians trained on all the appliances we sell, They have the
knowledge, skills, tools, parts, and equipment to ensure our pledge that "We
Service What We SelL"
Sears Maintenance Agreement
Maintain the value of your Dehumidifier with a Sears Maintenance Agreement.
Kenmore Dehumidifiers are designed, manufactured, and tested for years of
dependable operation.. Yet any appliance may require servicefrom time to time. The
SearsMaintenance Agreement offers you an outstanding service program for your
Kenmore Dehumidifier
The Sears Maintenance Agreement:
• Isyour way to buy tomorrow's service at today's prices.
o Eliminates repair bills resulting from normal use.
o Allows for as many service calls as you need.
- Provides an annual Preventive Maintenance Check at your request to keep your
Dehumidifier in proper running condition.
For more information, call 1-800-827-6655