Kenmore 41744102301, 41744142400 Installation Guide

Pre-lnstallation Requirements .......................... 2

Electrical Requirements ..................................... 2

Grounding Requirements ................................. 2

Water Supply Requirements .............................. 2

Drain Requirements .......................................... 2

Rough-In Dimensions ......................................... 3

Location Of Your Washer .................................. 4

Unpacking ......................................................... 4

Installation ......................................................... 5

Replacement Parts ............................................. 5

Before beginning installation, carefully read these instructions. This will simplify the installation
and ensure the washer is installed correctly and safely. Leave these instructions near the

washer after installation for future reference.

NOTE: The electrical service to the Washer must conform with local codes and ordinances and
the latest edition of the National Electrical Code, ANSI/NFPA 70.

Save These Instructions

Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.

1 P/N 134122600(0204)

Foryoursafetytheinformationin

thismanualmustbefollowedtominimizetheriskof
fireorexplosionor to preventpropertydamage,

personalinjuryorlossoflife.

- Donotstoreorusegasolineorotherflammable
vaporsandliquidinthevicinityofthisoranyother
appliance.

- WHATTODOIFYOUSMELLGAS

• Donottrytolightanyappliance.

• Donottouchanyelectrical switch; do not use

any phone in your building.

• Clear the room, building orarea of all
occupants.

• Immediately call your gas supplier from a

neighbor's phone. Follow the gas suppliers
instructions.

• If you cannot reach your gas supplier, call the
fire department.

Installation and service must be performed by a

qualified installer, service agency or the gas supplier.

PRE-INSTALLATION REQUIREMENTS

Tools Required for Installation:

1. 1/4 in. nut driver

2. 3/8 in. socket with ratchet.

3. 3/8 in. open end wrench.

4. 7/16 in. socket with ratchet.

5. 9/16 in. open end wrench.

6. Channel-lock adjustable pliers.

7. Carpenter's level.

ELECTRICAL REQUIREMENTS

.

Since your washer is equipped with a power supply
cord having an equipment-grounding conductor and

a grounding plug, the plug MUST be plugged into
an appropriate, copper wired receptacle that is

properly installed and grounded in accordance with
all local codes and ordinances or in the absence

of local codes, with the National Electrical Codes,
ANSI/NFPA 70 (latest edition). If in doubt, call a

licensed electrician. DO NOT cut off or alter the
grounding prong on the power supply cord. In

situations where a two-slot receptacle is present,
it is the owner's responsibility to have a licensed

electrician replace it with a properly grounded
three prong grounding type receptacle.

WATER SUPPLY REQUIREMENTS

Hot and cold water faucets MUST be installed within
42 inches (107 cm) of your washer's water inlet. The

faucets MUST be 3/4 inch (1.9 cm) garden hose type
so inlet hoses can be connected. Water pressure MUST
be between 10 and 120 pounds per square inch
(maximum unbalance pressure, hot vs. cold, 10 psi.)
Your water department can advise you of your water
pressure. The hot water temperature should be about

140 degrees F (60 degrees C).

DRAIN REQUIREMENTS

1. Drain capable of eliminating 17 gals (64.3 L) per
minute.

2. A standpipe diameter of 1-1/4 in. (3.18 cm)
minimum.

3. The standpipe height above the floor should be:

Minimum height: 24 in. (61 cm)
Maximum height: 96 in. (244 cm)

CIRCUIT - Individual, properly polarized and grounded

15 amp. branch circuit fused with 15 amp. time delay

fuse or circuit breaker.
POWER SUPPLY- 2 wire, with ground, 120 volt, single

phase, 60 Hz, Alternating Current.
OUTLET RECEPTACLE - Properly grounded 3-prong

receptacle to be located so the power supply cord is
accessible when the washer isin an installed position.

GROUNDING REQUIREMENTS

_ Improper connection of the equipment
grounding conductor can result in a risk of electrical

shock. Check with a licensed electrician if you are in
doubt as to whether the appliance is properly grounded.

The washer MUST be grounded. In the event of
malfunction or breakdown, grounding will reduce
the risk of electrical shock by a path of least

resistance for electrical current.

24in.

(81cm)

MUn=

BACK

NOTE:

Drain hose attached to the washer can reach a 58

in. (147 cm) high standpipe. For higher standpipe
use hose DIV 26970131461201, available from

Sears Parts and Service. Ifdrain is less than 24
in. (61 cm), install a siphon break kit, available at

your local hardware store.

96 in=

(244 cm)

MUn.