Kenmore 415.16944010, 415.16941010, 415.16942010 Use & Care Manual

Use & Care Guide

®

Liquid Propane Gas Grill

Sears Model No. 415.16944010

Safety

•

• Parts

• Use and Care

•

Assembly

This Grill is for Outdoor Use Only

WARNING

• Read and follow all Safety, Assembly,
and Use & Care Instructions in this
Guide before assembling and cooking
with this grill.

• Failure to follow all instruc tions in this
Use & Care Guide may lead to fire or
explosion, which could result in property
damage, personal injury or death.

See our extensive assortment of outdoor living products on-line at

Sears Brands Management Corporation, Hoffman Estates, IL 60179 U.S.A.

©2010 Sears Brands, LLC

Grill Information Center

Missing Parts? Assembly Questions?
Operation Problems? Before returning
grill to store, call 1-800-241-7548

Tools needed for assembly:

Adjustable wrench (not provided)
Screwdriver (not provided)
7/16" Combination wrench (not provided)

SAVE THESE INSTRUCTIONS!

www.sears.com and www.kmart.com

Printed in China

Model 464223610

G528-001-010801 • Oct-28-09

DANGER

WARNING

If you smell gas:

1. Shut off gas to the appliance.

2. Extinguish any open flame.

3. Open lid.

4. If odor continues, keep away from the appliance
and immediately call your gas supplier or your
fire department.

WARNING

1. Do not store or use gasoline or other
flammable liquids or vapors in the vicinity of
this or any other appliance.

2. An LP Tank not connected for use shall not
be stored in the vicinity of this or any other
appliance.

Call Grill Information Center for Help and Parts

Missing Parts? Assembly Questions?
Operation Problems? Before returning
grill to store, call 1-800-241-7548

Product Record

IMPORTANT: Fill out the product record information below.

Model Number

Serial Number

See rating label on grill for serial number.

CALIFORNIA PROPOSITION 65

1. Combustion by-products produced when using
this product contain chemicals known to the State of
California to cause cancer, birth defects, and other
reproductive harm.

2. This product contains chemicals, including lead
and lead compounds, known to the State of
California to cause cancer, birth defects or other
reproductive harm.

Wash your hands after handling this product.

Installation Safety Precautions

• Use grill, as purchased, only with LP (propane) gas and the

regulator/valve assembly supplied.

• Grill installation must conform with local codes, or in the
absence of local codes, with either the National Fuel Gas

Code, ANSI Z223.1/ NFPA 54, Natural Gas and Propane
Installation Code, CSA B149.1, or Propane Storage and
Handling Code, B149.2, or the Standard for Recreational
Vehicles, ANSI A 119.2/NFPA 1192, and CSA Z240 RV Series,
Recreational Vehicle Code, as applicable.

• All electrical accessories (such as rotisserie) must be
electrically grounded in accordance with local codes, or

National Electrical Code, ANSI / NFPA 70 or Canadian
Electrical Code, CSA C22.1. Keep any electrical cords and/or

fuel supply hoses away from any hot surfaces.

• Grill is not for use in or on recreational vehicles and/or boats.

• This grill is safety certified for use in the United States and/or
Canada only. Do not modify for use in any other location.
Modification will result in a safety hazard.

Safety Symbols

The symbols and boxes shown below explain what each heading
means. Read and follow all of the messages found throughout
the manual.

Date Purchased

To Installer/Assembler: Leave these instructions with
consumer.

To Consumer: Keep this manual for future reference.

CAUTION

• Some parts may contain sharp edges,
especially as noted in these instructions.
Wear protective gloves if necessary.

CAUTION

For residential use only. Do not use for commercial
cooking.

2 • 464223610

DANGER

DANGER: Indicates an imminently hazardous situation
which, if not avoided, will result in death or serious injury.

WARNING

WARNING: Be alert to the possibility of serious bodily injury
if the instructions are not followed. Be sure to read and
carefully follow all of the messages.

CAUTION

CAUTION: Indicates a potentially hazardous situation which,
if not avoided, may result in minor or moderate injury.

Table of Contents

WARRANTY

For Your Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Grill Service Center. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Product Record Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Safety Symbols. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Installation Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Kenmore Elite Grill Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Use and Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-10

Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Parts Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-22

Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23-25

Repair Protection Agreements

Congratulations on making a smart purchase. Your new
Kenmore® product is designed and manufactured for years of
dependable operation. But like all products, it may require repair
from time to time. That’s when having a Repair Protection
Agreement can save you money and aggravation.

Here’s what the Repair Protection Agreement* includes:
Expert service by our 10,000 professional repair specialists

Unlimited service and no charge for parts and labor on all

covered repairs

Product replacement up to $1500 if your covered product

can’t be fixed

Discount of 10% from regular price of service and related

installed parts not covered by the agreement; also, 10% off
regular price of preventive maintenance check

Fast help by phone – we call it Rapid Resolution –

phone support from a Sears representative. Think of us

as a “talking owner’s manual.”
Once you purchase the Repair Protection Agreement, a
simple phone call is all that it takes for you to schedule service.
You can call anytime day or night, or schedule a service
appointment online.
The Repair Protection Agreement is a risk-free purchase. If
you cancel for any reason during the product warranty period,
we will provide a full refund. Or, a prorated refund anytime after
the product warranty period expires. Purchase your Repair
Protection Agreement today!

Some limitations and exclusions apply. For prices and
additional information in the U.S.A. call 1-800-827-6655.
*Coverage in Canada varies on some items. For full details
call Sears Canada at 1-800-361-6665.
Sears Installation Service

For Sears professional installation of home appliances, garage
door openers, water heaters, and other major home items, in the
U.S.A. or Canada call 1-800-4-MY-HOME®.

KENMORE GRILL WARRANTY

One Year Full Warranty on Kenmore Grill

If this grill fails due to a defect in material or workmanship
within one year from the date of purchase, call 1-800-4-MY-

®

HOME to arrange for free repair (or replacement if repair
proves impossible).

Ten-Year Limited Warranty on Burners

For ten years from the date of purchase, any burner that
rusts through will be replaced free of charge. After the first
year from the date of purchase, you pay for labor if you wish
to have it installed.

All warranty coverage excludes ignitor batteries and grill part
paint loss, discoloration or surface rusting, which are either
expendable parts that can wear out from normal use within
the warranty period, or are conditions that can be the result
of normal use, accident or improper maintenance.

All warranty coverage is void if this grill is ever used for
commercial or rental purposes.

All warranty coverage applies only if this grill is used in the
United States.

This warranty gives you specific legal rights, and you may
also have other rights which vary from state to state.

Sears, Roebuck and Co., Hoffman Estates, IL 60179

Dual Fuel™ and SureFire™ are registered trademarks of
the W. C. Bradley Company and used, with permission,
by Sears Holding Corporation. All rights reserved.

464223610 • 3

USE AND CARE

DANGER

• NEVER store a spare LP cylinder under or near the

appliance or in an enclosed area.

• Never fill a cylinder beyond 80% full.

• If the information in the two points above is not

followed exactly, a fire causing death or serious
injury may occur.

• An over filled or improperly stored cylinder is a

hazard due to possible gas release from the safety
relief valve. This could cause an intense fire with
risk of property damage, serious injury or death.

• If you see, smell or hear gas escaping, immediately

get away from the LP cylinder and appliance and
call your fire department.

LP Tank

• The LP Tank used with your grill must meet the following
requirements:

• Use LP Tanks only with these required measurements: 12"

(30.5cm) (diameter) x 18" (45.7 cm) (tall) with 20 lb. (9 kg.)
capacity maximum.

• LP Tanks must be constructed and marked in accordance with
specifications for LP Tanks of the U.S. Department of
Transportation (DOT) or for Canada, CAN/CSA-B339, tanks,
spheres and tubes for transportation of dangerous goods.
Transport Canada (TC). See LP Tank collar for marking.

• LP Tank valve must have:

• Type 1 outlet compatible with

regulator or grill.

• Safety relief valve.

• UL listed Overfill Protection

Device (OPD). This OPD safety
feature is identified by a unique triangular hand wheel. Use

only LP Tanks equipped with this type of valve.

• LP Tank must be arranged for vapor withdrawal and include
collar to protect LP Tank valve. Always keep LP Tanks in
upright position during use, transit or storage.

LP Tank in upright position for vapor withdrawal

OPD Hand Wheel

LP Tank Removal, Transport And Storage

• Turn OFF all control knobs and LP tank valve. Turn coupling
nut counterclockwise by hand only - do not use tools to
disconnect. Lift LP tank wire upward off of LP tank collar, then
lift LP tank up and off of support bracket. Install safety cap onto
LP tank valve. Always use cap and strap supplied with valve.

Failure to use safety cap as directed may result in serious
personal injury and/or property damage.

LP Tank Valve

Safety Cap

Retainer Strap

• A disconnected LP tank in storage or being transported must
have a safety cap installed (as shown). Do not store an LP tank
in enclosed spaces such as a carport, garage, porch, covered
patio or other building. Never leave an LP tank inside a vehicle
which may become overheated by the sun.

• Do not store an LP tank in an area where children play.

4 • 464223610

LP (Liquefied Petroleum Gas)

• LP gas is nontoxic, odorless and colorless when produced. For
Your Safety, LP gas has been given an odor (similar to rotten

cabbage) so that it can be smelled.

• LP gas is highly flammable and may ignite unexpectedly when
mixed with air.

LP Tank Filling

• Use only licensed and experienced dealers.

• LP dealer must purge new tank before filling.

• Dealer should NEVER fill LP Tank more than 80% of LP Tank

volume. Volume of propane in tank will vary by temperature.

• A frosty regulator indicates gas overfill. Immediately close LP
Tank valve and call local LP gas dealer for assistance.

• Do not release liquid propane (LP) gas into the atmosphere.
This is a hazardous practice.

• To remove gas from LP Tank, contact an LP dealer or call a
local fire department for assistance. Check the telephone
directory under “Gas Companies” for nearest certified LP
dealers.

LP Tank Exchange

Connecting Regulator To The LP Tank

• Many retailers that sell grills offer you the option of replacing
your empty LP tank through an exchange service. Use only
those reputable exchange companies that inspect, precision fill,
test and certify their tanks. Exchange your tank only for an

OPD safety feature-equipped tank as described in the "LP
Tank" section of this manual.

• Always keep new and exchanged LP tanks in upright position

during use, transit or storage.

• Leak test new and exchanged LP tanks BEFORE

connecting to grill.

• Place dust cap on cylinder valve outlet whenever the cylinder is
not in use. Only install the type of dust cap on the cylinder valve
outlet that is provided with the cylinder valve. Other types of caps

or plugs may result in leakage of propane.

LP Tank Leak Test

For your safety

• Leak test must be repeated each time LP tank is exchanged or

refilled.

• Do not smoke during leak test.

• Do not use an open flame to check for gas leaks.

• Grill must be leak tested outdoors in a well-ventilated area,

away from ignition sources such as gas fired or electrical
appliances. During leak test, keep grill away from open flames
or sparks.

• Use a clean paintbrush and a 50/50 mild soap and water
solution. Brush soapy solution onto areas indicated by arrows
in figure below. Leaks are indicated by growing bubbles.

WARNING

If “growing” bubbles appear do not use or move the LP tank.
Contact an LP gas supplier or your fire department!

1. LP tank must be properly secured onto grill. (Refer to
assembly section.)

2. Turn all control knobs to the OFF position.

3. Turn LP tank OFF by turning OPD hand wheel clockwise to a
full stop.

4. Remove the protective cap from LP tank valve. Always use

cap and strap supplied with valve.

c

k

w

o

i

l

s

e

Strap and Cap

OPD Hand Wheel

Type 1 outlet with
thread on outside

Safety Relief Valve

C

f

f

O

Do not insert a POL transport plug
(plastic part with external threads)

into the Type 1 tank valve outlet.
It will defeat the Safety Relief Valve

feature.

s Do not use household cleaning agents. Damage to gas

train components ( can result.valve/hose/regulator)

5. Hold regulator and insert nipple into LP
tank valve. Hand-tighten the coupling
nut, holding regulator in a straight line
with LP tank valve so as not to cross­thread the connection.

Nipple has to be centered
into the LP tank valve.

464223610 • 5

Leak Testing Valves, Hose and Regulator

1. Turn all grill control knobs to OFF.

Straight

Hold coupling nut and regulator
as shown for proper connection
to LP tank valve.

6. Turn the coupling nut clockwise and tighten to a full stop. The

regulator will seal on the back-check feature in the LP tank
valve, resulting in some resistance. An additional one-half to

three-quarters turn is required to complete the
connection. Tighten by hand only – do not use tools.

NOTE:

If you cannot complete the connection, disconnect regulator and
repeat steps 5 and 6. If you are still unable to complete the
connection, do not use this regulator!

Call 1-800-4-MY-HOME for identical replacement part.

2. Be sure regulator is tightly connected to LP tank.

3. Completely open LP tank valve by turning OPD hand wheel

counterclockwise. If you hear a rushing sound, turn gas off
immediately. There is a major leak at the connection. Correct

before proceeding by calling Sears for replacement parts at
1-800-4-MY-HOME .

®

4. Brush soapy solution onto areas where bubbles are shown in
picture below:

Never remove threaded

orifice at end of valve.

DANGER

• Do not insert any tool or foreign objects into the valve outlet
or safety relief valve. You may damage the valve and cause
a leak. Leaking propane may result in explosion, fire, severe
personal injury, or death.

• If a leak is detected at any time, STOP and call the fire
department.

• If you cannot stop a gas leak, immediately close LP tank
valve and call LP gas supplier or your fire department!

WARNING

• Never attempt to attach this grill to the self-contained LP gas
system of a camper trailer or motor home.

• Do not use grill until leak-tested.

5. If “growing” bubbles appear, there is a leak. Close LP tank
valve immediately and retighten connections. If leaks cannot
be stopped do not try to repair. Call Sears for replacement
parts at 1-800-4-MY-HOME .

®

6. Always close LP tank valve after performing leak test by
turning hand wheel clockwise.

6 • 464223610

WARNING

For Safe Use of Your Grill and to Avoid Serious
Injury:

• Do not let children operate or play near grill.

• Keep grill area clear and free from materials that burn.

• Do not block holes in sides or back of grill.

• Check burner flames regularly.

• Use grill only in well-ventilated space. NEVER use in

enclosed space such as carport, garage, porch,
covered patio, or under an overhead structure of any
kind.

• Do not use charcoal or ceramic briquets in a gas grill.
(Unless briquets are supplied with your grill.)

• Use grill at least 3 ft. from any wall or surface.

Maintain 10 ft. clearance to objects that can catch fire
or sources of ignition such as pilot lights on water
heaters, live electrical appliances, etc.

Safety Tips

sBefore opening LP cylinder valve, check the coupling nut for

tightness.

sWhen grill is not in use, turn off all control knobs and LP

cylinder valve.

sNever move grill while in operation or still hot.
sUse long-handled barbecue utensils and oven mitts to avoid

burns and splatters.

sMaximum load for sideburner and side shelf is 10 lbs.
sThe grease tray must be inserted into grill and emptied after

each use. Do not remove grease tray until grill has
completely cooled.

s Clean grill often, preferably after each cookout. If a bristle

brush is used to clean any of the grill cooking surfaces,

ensure no loose bristles remain on cooking surfaces prior to
grilling. It is not recommended to clean cooking surfaces
while grill is hot.

sIf you notice grease or other hot material dripping from grill

onto valve, hose or regulator, turn off gas supply at once.
Determine the cause, correct it, then clean and inspect valve,
hose and regulator before continuing. Perform a leak test.

sKeep ventilation openings in cylinder enclosure (grill cart) free

and clear of debris.

sDo not store objects or materials inside the grill cart

enclosure that would block the flow of combustion air to the
underside of either the control panel or the firebox bowl.

sThe regulator may make a humming or whistling noise during

operation. This will not affect safety or use of grill.

sIf you have a grill problem see the "Troubleshooting Section".
sIf the regulator frosts, turn off grill and LP cylinder valve

immediately. This indicates a problem with the cylinder and it
should not be used on any product. Return to supplier!

• Apartment Dwellers:

Check with management to learn the requirements
and fire codes for using an LP gas grill in your
apartment complex. If allowed, use outside on the
ground floor with a three (3) foot clearance from walls
or rails. Do not use on or under balconies.

• NEVER attempt to light burner with lid closed. A
buildup of non-ignited gas inside a closed grill is
hazardous.

• Never operate grill with LP cylinder out of correct
position specified in assembly instructions.

• Always close LP cylinder valve and remove
coupling nut before moving LP cylinder from
specified operation position.

CAUTION

• Putting out grease fires by closing the lid is not possible.
Grills are well ventilated for safety reasons.

• Do not use water on a grease fire. Personal injury may
result. If a grease fire develops, turn knobs and LP
cylinder off.

• Do not leave grill unattended while preheating or burning
off food residue on HI. If grill has not been regularly
cleaned, a grease fire can occur that may damage the
product.

Main Burner Ignitor Lighting

s Do not lean over grill while lighting.

1. Open lid during lighting.

2. Turn on gas Tank valve.

3. Push and turn any burner control knob to HI and
immediately press and hold ELECTRONIC IGNITION button.

4. If ignition does NOT occur in 5 seconds, turn burner control

knob OFF, wait 5 minutes for gas to clear away, and repeat the
lighting procedure.

5. Repeat above steps to light each burner individually.

If ignition still does not occur, follow match-lighting
instructions.

464223610 • 7

WARNING

Turn controls and gas source or tank OFF when not
in use.

CAUTION

Burner Flame Check

• Remove cooking grates and flame tamers. Light burners, rotate

knobs from HI to LOW. You should see a smaller flame in
LOW position than seen on HI. Perform burner flame check
on sideburner, also. Always check flame prior to each use. If
only low flame is seen refer to "Sudden drop or low flame" in
the Troubleshooting Section.

HI

If ignition does NOT occur in 5 seconds, turn the
burner controls OFF, wait 5 minutes and repeat the
lighting procedure. If the burner does not ignite with
the valve open, gas will continue to flow out of the
burner and could accidently ignite with risk of injury.

Main Burner Match-Lighting

 Do not lean over grill while lighting.

1. Turn OFF all burner control valves.

2. Open lid during lighting. Turn on gas at LP cylinder.

3. Place match into match holder (hanging from side of cart).

Light match, and place into lighting hole for desired burner to
light. The lighting holes are located at the front of the cooking
grates between the emitter plate mounting brackets.

4. Push in and turn control knob to HI position for desired
burner to light. Be sure burner lights and stays lit.

5. If ignition does NOT occur in 5 seconds, turn the burner
Control knob off, wait 5 minutes for gas to clear away, and
repeat the match lighting procedure.

6. Ignite remaining burners by repeating steps 3 through 5 for
each burner.

Side Burner Ignitor Lighting

s Do not lean over grill while lighting.

1. Open lid during lighting.

2. Turn ON gas tank valve.

3. Push and turn sideburner control knob to HI and
immediately press and hold ELECTRONIC IGNITION button.

4. If ignition does NOT occur in 5 seconds, turn burner control

knob OFF, wait 5 minutes for gas to clear away, and repeat the
lighting procedure.

5. Repeat above steps to light each burner individually.

Sideburner Match Lighting

1. Turn OFF all burner control valves.

2. Open the sideburner lid.
Turn on gas at LP cylinder.

3. Place lit match near burner.

4. Turn sideburner knob to HI .

Be sure burner lights and stays lit.

WARNING: Sideburner top cover must be open when

sideburner is in operation.

8 • 464223610

LOW

Turning Grill Off

• Turn all knobs to the OFF position. Turn LP cylinder OFF by
turning hand-wheel clockwise to a full stop.

Ignitor Check

• Turn gas off at LP cylinder. Press and hold electronic ignitor

button. "Click" should be heard and spark seen each time
between each collector box or burner and electrode. See
"Troubleshooting" if no click or spark.

Valve Check

• Important: Make sure gas is off at LP cylinder before
checking valves. Knobs lock in position. To check

valves, first push in knobs and release, knobs should spring
back. If knobs do not spring back, replace valve assembly
before using grill. Turn knobs to LOW position then turn back to
OFF

position. Valves should turn smoothly.

OFF

Hose Check

• Before each use, check to see if hoses are cut or worn.

Replace damaged hoses before using grill. Use only

identical replacement part valve/hose/regulator as
specified in the Parts List of this Use and Care Guide.

General Grill Cleaning

• Do not mistake brown or black accumulation of grease and
smoke for paint. Interiors of gas grills are not painted at the
factory (and should never be painted). Apply a strong solution
of detergent and water or use a grill cleaner with scrub brush
on insides of grill lid and bottom. Rinse and allow to completely
air dry. Do not apply a caustic grill/oven cleaner to painted
surfaces.

• Plastic parts: Wash with warm soapy water and wipe dry.
s Do not use citrisol, abrasive cleaners, degreasers or a
concentrated grill cleaner on plastic parts. Damage to and
failure of parts can result.

• Porcelain surfaces: Because of glass-like composition, most
residue can be wiped away with baking soda/water solution or
specially formulated cleaner. Use nonabrasive scouring powder
for stubborn stains.

• Painted surfaces: Wash with mild detergent or nonabrasive
cleaner and warm soapy water. Wipe dry with a soft
nonabrasive cloth.

• Stainless steel surfaces: To maintain your grill’s high quality
appearance, wash with mild detergent and warm soapy water
and wipe dry with a soft cloth after each use. Baked-on grease
deposits may require the use of an abrasive plastic cleaning
pad. Use only in direction of brushed finish to avoid damage.
Do not use abrasive pad on areas with graphics.

• Cooking surfaces: If a bristle brush is used to clean any of

the grill cooking surfaces, ensure no loose bristles remain on
cooking surfaces prior to grilling. It is not recommended to
clean cooking surfaces while grill is hot.

CAUTION

SPIDER ALERT!

SPIDER AND WEBS

INSIDE BURNER TUBE

If you notice that your grill is getting hard to light or that the
flame isn’t as strong as it should be, take the time to check and
clean the burner tubes.

CONTROL PANEL

VALVE

In some areas of the country, spiders or small insects have been
known to create “flashback” problems. The spiders spin webs, build
nests and lay eggs in the grill’s burner tube(s) obstructing the
flow of gas to the burner. The backed-up gas can ignite in the burner
tube behind the control panel. This is known as a flashback and it
can damage your grill and even cause injury.

To prevent flashbacks and ensure good performance the burner and
burner tube assembly should be removed from the grill and cleaned
before use whenever the grill has been idle for an extended period.

SPIDER WEBS

INSIDE BURNER TUBE

BURNER

3. Remove carryover tubes and burners.

4.

Detach electrode from burner.

NOTE: Removal/Detachment method will depend on the
burner configuration. See different configurations in
illustrations below.

5. Carefully lift each burner up and away from valve openings.

We suggest three ways to clean the burner tubes. Use the one

easiest for you.

(A) Bend a stiff wire (a light weight coat hanger works well)

into a small hook. Run the hook through each burner
tube several times.

(B) Use a narrow bottle brush with a flexible handle (do not

use a brass wire brush), run the brush through each
burner tube several times.

(C) Wear eye protection: Use an air hose to force air into

the burner tube and out the burner ports. Check each
port to make sure air comes out each hole.

6. Wire brush entire outer surface of burner to remove food

residue and dirt.

7. Clean any blocked ports with a stiff wire such as an open

paper clip.

8. Check burner for damage, due to normal wear and corrosion

some holes may become enlarged. If any large cracks or
holes are found replace burner.

VERY IMPORTANT: Burner tubes must reengage valve

openings. See illustrations at right.

9. Attach electrode to burner.

10. Carefully replace burners.

Correct

burner-to-valve

engagement

11. Attach burners to brackets on firebox.

12. Reposition carryover tubes and attach

to burners. Replace flame tamers and
cooking grates.

Remove screws

rebox

Fi

Storing Your Grill

• Clean cooking grates.

• Store in dry location.

• When LP cylinder is connected to grill, store outdoors in a well­ventilated space and out of reach of children.

• Cover grill if stored outdoors. Choose from a variety of grill
covers offered by manufacturers.

• Store grill indoors ONLY if LP cylinder is turned off and
disconnected, removed from grill and stored outdoors.

• When removing grill from storage, follow “Cleaning the Burner
Assembly” instructions before starting grill.

Cleaning the Burner Assembly

Follow these instructions to clean and/or replace parts of burner
assembly or if you have trouble igniting grill.

1. Turn gas OFF at control knobs and LP cylinder.

2.

Remove cooking grates and flame tamers.

Firebox

be

tu

Carryover

Firebox
burner
bracket

Carryover tube

Firebox burner
bracket

Electrode

Electrode

Pry off
electrode with
a flat blade
screwdriver

464223610 • 9