Kenmore 405.35090510, 405.35040510, 405.35182510, 405.35162510, 405.35016510 Use & Care Manual

Use & Care Guide
Manual de Uso y Cuidado

English/Español

9"Metal Fan

2 Speeds, 360°Adjustable Tilt

Ventilador Metálico 9"

2 Velocidades, Inclinación Ajustable de 360°

Model/Modelo: 405.35090510

Customer Assistance /Asistencia al Cliente

1-866-646-4332

Sears Brands Management Corporation
Hoffman Estates, IL 60179 U.S.A.

www.kenmore.com
www.sears.com
www.kmart.com

®

Kenmore®

CAUTION

Read and follow all instructions before operating fan. Do not use fan if any part
are damaged or missing.

WARNING

1. This appliance is not intended for use by young children or infirm persons
without supervision.

2. Young children should be supervised to ensure that they do not play with the
appliance.

3. This appliance has a polarized plug (one blade is wider than the other). To
reduce the risk of electrical shock, this plug is intended to fit in a polarized
outlet only one way. If the plug does not fit fully into the outlet, reverse the
plug. If the plug still does not fit, contact a qualified electrician. Do not attempt
to bypass this safety feature.

4. If the supply cord is damaged ,it must be replaced by manufacturer or its
service agent or a similarly qualified person in order to avoid a hazard.

5. To reduce the risk of fire or electrical shock, do no use this fan with any solid
state speed control device.

6. Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.

1

READ AND SAVE THESE INSTRUCTIONS

RULES FOR SAFE OPERATION

1. Never insert fingers, pencils, or any other object through the housing when the
fan is running. Disconnect it when moving from one location to another.

2. Disconnect fan when moving from one location to another.

3. Disconnect fan when removing grilles for cleaning.

4. Do not leave the fan running unattended.

5. Be sure the fan is on a stable, flat surface when in operation.

6. The rules about cords and plugs are as follows:
(1) This product uses overload protection (fuse). A blown fuse indicates an
overload or short-circuit situation. If the fuse burns out, unplug the
product from the outlet. Replace the fuse as per the user servicing
instructions (follow product marking for proper fuse rating) and check
the products.If the replacement fuse blows, a short-circuit may be present
and the product should be discarded or call Customer Assistance at
1-866-646-4332 to arrange for possible repair.
(2) Do not operate any fan with a damaged cord or plug. Discard fan or call
Customer Assistance at 1-866-646-4332 to arrange for possible repair.
(3) D o not run cord under carpeting. Do not cover cord with throw rugs,
runners, or similar coverings. Do not route cord under furniture or
appliances. Arrange cord away from traffic area and where it will
not be tripped over.

2

PARTS FIGURE

1. Power supply cord

2. On/Off Speed Switch

3. Grille Assembly

OPERATING INSTRUCTION

1. Plug the fan power cord into a 120 volt
electrical outlet.

2. Speed is controlled by the Rocker On/Off
Speed Switch. (I-O-II)
l = On/Low Speed
O = Off
ll = On/High Speed

3. Adjust angle of vertical air direction by
grasping the sides of the grille assembly
and tilting it either up or down.

1

2

3

FUSE REPLACEMENT

1. Grasp the plug and remove it from the receptacle
or other outlet device. Do not unplug by pulling on
the cord.

2. Open the fuse cover. Slide open the fuse access
cover on top of power plug towards blades.

3. Remove the fuse carefully. Push the fuse from the other side or turn the fuse
holder over to remove the fuse.
WARNING: Risk of fire. Replace the fuse only with 2.5 A, 125 Volt fuse.

4. Close the fuse cover. Slide closed the fuse access cover on top of the
power plug.
WARNING: Risk of fire. Do not replace power plug. It contains a safety

The fan requires little maintenance. Do not try to fix it by yourself. Refer it to
qualified service personnel if service is needed,or call Customer Assistance at
866-646-4332.

1. Before cleaning fan, always unplug it from the electrical outlet.

2. To ensure adequate air circulation to the motor, use a vacuum to keep vents
at the rear of the motor housing free from dust, fluff, etc. Do not disassemble
fan to remove dust or fluff.
CAUTION: To avoid injury from electrical shock, unplug the fan before using a
vacuum cleaner to clean the vents.

3. Wipe the exterior parts with a soft cloth soaking a mild detergent.
Do not use any abrasive detergent or solvents to avoid scratching the surface.
Do not use gasoline or paint thinner as a cleaner.

4. Do not allow water or any other liquid into the motor housing or interior parts.

MAINTENANCE INSTRUCTIONS