Kenmore 405.34030310 Use & Care Manual

Use & Care Guide
Manual de Uso y Cuidado

English/Español

Kenmore

®

30’’ Tower Fan

3 Speeds, Oscillation Switch

30’’ Ventilador La Torre

3 Velocidades, Oscilación Interruptor

Model/Modelo: 405.34030310

Customer Assistance /Asistencia al Cliente

1-855-438-7899

Sears Brands Management Corporation
Hoffman Estates, IL 60179 U.S.A.

www.kenmore.com
www.sears.com
www.kmart.com

®

CAUTION

Read and follow all instructions before operating fan. Do not use fan if any part
are damaged or missing.

WARNING

1. To reduce the risk of fire or electrical shock, do not use this fan with any
solid-state speed control device.

2. If the supply cord is damaged, it must be replaced by the manufacturer or its
service agent or other qualified person in order to avoid a hazard.

3. This appliance has a polarized plug (one blade is wider than the other). To
reduce the risk of electric shock, this plug is intended to fit in a polarized outlet
only one way. If the plug does not fit fully in the outlet, reverse the plug. If it
still does not fit, contact a qualified electrician. Do not attempt to defeat this
safety feature.

4. Do not leave the fan running unattended.

5. Keep electrical appliances out of reach of children. Do not let them use the
appliances without supervision.

RULES FOR SAFE OPERATION

1. Never insert fingers or any other objects through the fan housing when the
tower fan is running. Unplug the fan when moving it from one location to
another.

2. Disconnect the fan before cleaning.

3. To avoid overturning, be sure the fan is on a stable surface when operating it.

4. To reduce the risk of electric shock, DO NOT use the fan by a window.

5. The rules about cord and plug as below:
(1) This product employs overload protection (fuse). A blown fuse indicates an
overload or short-circuit situation. If the fuse blows, unplug the product from
the outlet. Replace the fuse as per the user servicing instructions (follow
product marking for proper fuse rating) and check the products. If the
replacement fuse blows, a short-circuit may be present and the product
should be discarded or returned to an authorized service facility for
examination and/or repair.

(2) Do not operate any fan with a damaged cord
or plug. Discard fan or or call the following
customer assistance number for possible
repair: 1-855-438-7899.
(3) Do not run cord under carpeting.Do not cover
cord with throw rugs, runners, or similar coverings.
Do not route cord under furniture or appliances.
Arrange cord away from traffic area and
where it will not be tripped over.

1

Figure 1

READ AND SAVE THESE INSTRUCTIONS

(4) This appliance is for private household use only.

PARTS (see Figure 1)

FAN ASSEMBLY

1. Unscrew the base attachment nut (4) from the bottom of fan body (1).

2. Pull power cord (5) all the way out.

3. Attach rear base half (2) and front base half (3) together by inserting the
four posts on front half into the four holes on rear half. Place assembled base

on floor.

4. Insert threaded post on bottom of fan body (1) through large center hole in

fan base. Fit Power cord (5) into power cord clip on rear base half.

MAINTENANCE INSTRUCTIONS

The fan requires little maintenance. Do not try to fix it by yourself. Refer it to
qualified service personnel if service is needed.To inquire about possible repair,

call the following customer assistance number: 1-855-438-7899.

1. Always make sure that the fan is unplugged from any electrical outlet before
cleaning or assembly.

2. To ensure adequate air circulation to the motor, keep vents at the rear of the
motor housing free of dust, fluff, etc. A vacuum cleaner should not be used to
clean these vents. Do not disassemble the fan to remove dust.

3. Wipe the exterior parts with a soft cloth soaking a mild detergent. Do
not use any abrasive detergent or solvents that could scratch the surface. Do
not use any of the following as a cleaner: gasoline or thinner.

4. Do not allow water or any other liquid into the motor housing or interior parts.

OPERATING INSTRUCTIONS

Control Switches (Fig. 2)

1. Body oscillating switch

2. Speed switches

Operation

1. Plug the power cord into a wall outlet.

2. Push the oscillating switch (OSC) to cause
the fan body to rotate continuously left
and right to direct the air flow across a
broader space. Push again to stop oscillation.

3. The speed is controlled by pushing one of the four speed switches (2) on top of
the fan body. The four speed settings are:
OFF; L (Low); M (Medium); H (High)

1. Fan Body 2. Rear Base Half (with clip for Power Cord) 3. Front Base Half

4. Base Attachment Nut 5. Power Cord

2

1

2

Figure 2

5. Carefully turn fan body and base upside down, and screw base attachment
nut (4) onto threaded post to secure fan and base together. Once the nut is
tightened into place, turn fan upright to operating position.