Kenmore 3639557880, 3639557854, 3639557850, 3639557820, 3639557810 Owner’s Manual

..ai
Safety instruchons :-..: ......................................................
Grounding Requirements .............................................2, 3
Refrigerator Location, Clearances, Rollers .............. 3
: " Electronic Alert & Diagnostic System .................. 4-6
. Automatic lcemaker & ice/Water Dispenser ......7, 8
Ice Service .................................................................... 9
° Adjusting Temperature Controls ...............................10
° Food Storage Suggestions ............................... t O, t 1
Shelves ................o.......................................................12, t 3
Storage Drawers .............................................................13
° Care and Cleaning .................................................14, t 5
° BeBre You Call br Service ........................... 16, 17
, AcCessories .............................. ................................. 17
° Vacation and Moving Precautions ..................17
° Warranty ............................................................Back Cover
Your old refrigerator has a cooling systemthat used
CFCs [chloroFluorocarbons). CFCs are believed to harm stratospheric ozone, so this refrigerator usesa new refrigerant
ihat does not harm the stratospheric ozone layer.
If you are throwing away your old refrigerator, make sure the CFC refrigerant is removed for proper disposal by a qualified
servicer. Ifyou intentionally release this CFC refrigerant you can be subject to fines and imprisonment under provisions of
the federal Clean Air Act....
Please record the model number, serial number and date you purchased your Kenmore refrigerator in the space below.
Model Number Serial Number Date of Purchase
SEARS,ROEBUCK AND CO, Hoffman Estates,IL601 79
Side by Side 27 Models
with Electronic Dispenser and Convenience Center
i PORTANTSAFETYINSTRUCTIONS
Read all:instructions before using - Don't refreeze frozen foods which have thawed
this appliance, completely. The United States Department of Agriculture
WARNING.When using thisappliance, always
: .......:................ .... .... ........... .. You may safeEyrefreeze frozen foods that have
exercise basiC safety precautions, including the thawed if they still contain ice crista{s or if they are still following: Cold-below 40 ° Fo(4°C.).
Use thls a ppllance onlyfor its in!ended
purpose as describeci in thisOwner s Manual. "...Thawed ground meats, poultry or fish that have any
:This refrigerator must be properly installed in accordance with the Attention: Installer
Instructions before it is used. See grounding
requirements below and on page 3.
' Repair or replace immediately all electric
service cords that have become frayed or otherwise ;damaged. Do not use a cord that shows cracks or abrasion damage along its length orat either the plug or
connector end.::
When moving your refrigerator away from the
Wall, be careful not to roll over or damage the
particularly when hands are damp or wet. Skin
may adhereto the extremely Cold surfaces.
, Do notplacefinge[s o r hands on the automatic replaced.) NOTE: Moving con!rol to OFF position does
icemaking mechanism while the refrigerator is "
plugged in.This Will heipprotect you from possible Do not allow children to climb, stand or hang on
injury, it wifl als0 prevent interference with the moving the shelves in the refrigerator. They could damage the
parts of the ejector mechanism, 0r with the heating refrigerator and seriously injure themselves°
element that releases the cubes
........ ....... " - Do not allow anyone to climb, stand or hang on
-Do not store or use gasoline or other flammable the Convenience Center Compartment door. They
vapors and liquids in the vicinity of this or any could damage the refrigerator and maybe tip it over,
other appllance.: causing severe personal injury.
in Home and Garden Bulletin No. 69 says:
off-odor or off-color should not be refrozen and should
not be eaten. Thawed ice cream should be discarded. If
the odor or color of any food is poor or questionable, get
rid of it.The food may be dangerous to eat.
"Even partial thawing and refreezing reduce the eating quality of foods, particularly fruits, vegetables and prepared foods. The eating quality of red meats is affected less than that of many other foods, Use refrozen foods as soon as possible to save as much of their eating quality as you can."
If your old refrigerator is still around the house but
not in use, be sure to remove the doors. This will
reduce the possibility of danger to children.
Unplug your refrigerator before cleaning and making repairs. NOTE: We strongly recommend that any servicing be performed by a qualified individual
Before replacing a burned-out light bulb, unplug the refrigerator or turn off power at the circuit breaker
or fuse box in order 1oavoid contact with a live wire fiiamenL (A burned-out light bulb may break when being
not remove power to the hght cJrcutt
SAVETHESEINSTRUCTIONS
Grounding Requirements Irnportant-_-,Pleaseread carefully.
To Connect Electricity
For personal safety,
this appliance must be properly grounded.
The power cord of this appliance is equipped with a three-prong
(grounding) plug which mates with a standard three- prong (grounding) wall outlet (Fig. 1)to minimize the possibility of electric shock hazard from thisappliance.
PREFERRED
Mk"THOD L__
Fig! _BEFORE USE _
Have wall outlet and circuit checked by a qualified electrician to make sure outlet is properly grounded
Where a standard two-prong wall outlet is encountered, itisyour personal responsibility and obligation to have it replaced with a properly grounded three-prong wall
outlet DO NOT, UNDER ANY CIRCUMSTANCES, CUT OR
REMOVE THE THIRD (GROUND) PRONG FROM
THE POWER CORD_
2
Starting the Refrigerator
Use of Adapter Plug
Because of potential safety hazards under certain conditions, we strongly recommend against use of an adapter plug. However, if you still elect to use an adapter, where local codes permit, a TEMPORARY CONNECTION may be made to a properly grounded lwo-prong wall outlet by use of a UL listed adapter
(Fig, 2) available at most local hardware stores.
TEMPORARYMETHOD
The larger slot in the adapter must be aligned with the
larger slot in the wall outlet to provide proper polarity
in the connection of the power cord..
CAUTION: Attaching an adapter ground terminal to the walt outlet cover screw does not ground the appliance
unless the cover screw is metal, and not insulated, and the wail outlet isgrounded through the house wiring. You
should have the circuit checked by a qualified electrician to make sure the outlet is properly grounded.
When disconnecting the power cord from the adapter, always hold the adapter with one hand,
If this is not done, the adapter ground terminal is very likely to break with repeated use.
Should the adapter ground terminal break,
DO NOT USE the appliance until a proper
ground has again been established.
iIAD,_, PLUGSNOT iPE_M_E0IN_NAoA_ il _ 1
i AUGNLARGE lJ _J'l[| !
iPRONG/SLOTS_._ il _ I
J Fig. 2 JJ FIRM CONNECTION
L_Z.JI 8E_OREUSE
GROUND AND
Use of Extension Cords
Because of potential safely hazards under certain
conditions, we strongly recommend against the use
of an extension cord_ However, if you still elect to use
an extension cord, it is absolutely necessary that it
be a UL listed 3-wire grounding type appliance
extension cord having a grounding type plug and
outlet and that the electrical rating of the cord be
15 amperes (minimum) and 120 volts.
Electrical Requirements
The refrigerator should always be plugged into its
own individual electrical outlet which has a voltage
rating that matches the rating plate Thisprovides the
best performance and also prevents overloading house wiring circuits, which could cause a fire hazard from
overheating wires..
Location
e Install the refrigerator on a floor strong enough to
support it when it is fully loaded.
e Do not install it where the temperature will go
below 60°F. (16°C_) because it will not run often enough to maintain proper temperatures.
° Do not install it next to your range, a heating vent
or where the sun will shine directly on it.
Clearances
Allow the following clearances for ease of installation,
proper air circulation, and plumbing and electrical connections:
Sides ........5/8" (] 6 mm) Top ......................1" (25 mm)
Back ................1" (25 mm)
(If built-in, allow 7/8" [22 mm] at top for hinge covers_)
Allow a 1'.,'2"(38 mm) door clearance at Convenience
Center side.
Rollers
Adjustable rollers behind the base grille enable you to move the refrigerator away from the wall for
cleaning These rollers should be setso the refrigerator restsfirmly on the floor, To assure that the doors will close automatica[ly from a halfway-open position,
there isa built-in tilt from the front to the back of the cabinet Side-by-side refrigerators also have specially
designed door hinges that lift both doors slightly
when opened, allowing the force of gravity to help
close them securely
To adjust the rollers:
o Remove the base grille_
Grasp it at the bottom and pull it out°
o Turn the roller adjusting
screws clockwise to raise the refrigerator, counter-
clockwise to lower it Use an adjustable wrench or
pliers on the 3/8" bolts. Both doors should close properly when bottom front edge of
refrigerator cabinet is about 5/8" from the floor ,/'
,, To replace the base grille, line up the prongs on the grille with the clamps on the refrigerator and push
forward until the grille snaps ,_. into place.
ElectronicAlert & Diagnostic System
NORMAL DOOR)PEN
Q
WARMTEMP
D
Kenmore
(_ Red signal light flashes totell you when either door
is open_
(_) Signal light tells you that the Door Alarm beeper has
been set to sound after either door has been open 30 seconds..
(_) Red signal light tells you when freezer foodkeeping
temperature is above normal.
(_ Lighted word NORMAL indicates that no failure has
been detected by the diagnostic system
(_) Flashing diagnostic codes in the display
warn you when:
_ power has been interrupted.
_ defrost system has failed. I_ frozen foods should be checked.
i
pF POWER
dE DEFROST FF FREEZ£R
£t ICEMAK_
. ......... J
i
SYSTEM
CHECK
RESET
CUBE01 rIDOoR M]
j J oN/oj
When your refrigerator is first plugged inn,,,
All panel lights come on for five seconds, a beep sounds,
and lights go off except as follows: " PFflashes in the display. Touch SYSTEM CHECK-RESET
pad to erase it,
" Word NORMAL glows.
Red WARM TEMPERATURE light glows if freezer compartment temperature is higher than normal. It goes
off when proper foodkeeping temperature is reached.
" Door alarm beeper is activated and light on DOOR
ALARM pad glows.
CRUSHED ICE selection light glows
Red DOOR OPEN light flashes if either door is open, goes out when doors are shut°
Night light in water-and-ice dispenser is off,
i icemaker may not be operating properly.
What these codes mean-and what to do when they appear-is summarized on the inside of the freezer
compartment door and explained more thoroughly on the following pages..
(_ SYSTEM CHECK-RESET pad puts a review of
the electronic diagnosis of four coded functions at your fingertip and also allows you to erase codes
from display. Electronic control allows you to select ice cubes,
crushed ice or chilled water and signal light confirms
your choice.
How to Set the Door Alarm,
You don't have to set the visual alarm. As long as either door is
open, the red DOOR OPEN signal light flashes
If the signal light on the DOOR ALARM pad isglowing,
the beeper alarm is set. tf it's not,
touch the pad to turn it on If either door is open for more than
30 seconds, a recurring beep sounds
The light goes out and the beeping stops when you close
the door_
There are times when you'll want the Door Alarm
beeper turned off. When you're rearranging a lot of food, for example. Just touch the pad**The light wilt go
out and the beeping win stop Deactivating the Door Alarm beeper does not turn the
red DOOR OPEN light off-it keeps flashing until the door is closed
DOOR OPEN
ONfOFF J
How the Electronic Alert
and Diagnostic System Works,
The word NORMAL is lighted except when a failure has
been detected.
The SYSTEM CHECK-RESET pad has two functions:
1.You can touch the SYSTEM CHECK-RESET pad and get a
review of the electronic diagnostic codes in order of their priority.
2.You can touch the SYSTEM CHECK-RESET pad to erase three flashing codes immediately and two codes after the condition that caused them to flash has been
corrected (see the next page)
NORMAL
/ CHECK/1
L RESET JI
(continued next page)
Why the Red Warm Tern peratu re Light G Io-ws.
At first, it's probably because your newly installed refrigerator
hasn't completely cooled down
yet. Wait a few hours for it to coo!,
and then the light will go out From then on, the red light will glow whenever
temperatures inside get too high for proper food storage tf this happens, open the doors only when absolutely
necessary, and close them as quickly as possible
As soon as inside temperatures return to normal, the light
goes ouL If the WARM TEMP light reappears and stays on for
longer than 4 hours, call for service
WARMTEMP
ElectronicAlert & Diagnostic System(continued)
The Electronic Alert and Diagnostic System alerts you when something starts to go wrong
If a system code appears on the display,
something needs special attention. To get your attention, the display code Flashesuntil you erase iL
The first 6 flashes are accompanied by beeps
If more than one coded function requires attention
at the same time, the one with the highest priority will be
displayed first Pressing the SYSTEM CHECK-RESET pad wi!l evaluate all
other coded functions If the NORMAL display islit during the displaying of a code, that function is operating
propedy
Pressing the SYSTEM CHECK-RESET pad will erase
two codes immediately-PF, and CI The dE and
FFcodes can only be erased by touching the
SYSTEM CHECK-RESET pad after the condition that caused the code to flash has been corrected.
This flashing code tells you the
power to the refrigerator has been interrupted for more than
2 seconds Check the condition of food in both the fresh food and
freezer corn pa rtments Touch SYSTEM CHECK-RESET pad to
erase code,,
There is no fault with the refrigerator when
PFcode flashes
This flashing code tells you
to check your frozen food. Has any of it started to thaw? A package may be holding the
freezer compartment door open Don't open the door more often than absolutely necessary whi!e this code is displayed Touching the SYSTEM CHECK-RESET pad after the freezer compartment temperature has returned to normal will
erase the code This flashing code tells you to
check the automatic icemaker.
Ice clumps in the storage bin may
have stalled the icemaker Follow corrective measures described on
page 8 If water supply to the icemaker is not connected or not
turned on, make sure manual
icemaker switch isin the STOP position Code stops Flashing when problem is corrected or SYSTEM CHECK-
RESETpad istouched
This flashing code tells you
something's wrong with the defrost system- keep doors closed to
retain cold and call for service. Code flashes unti! problem is
corrected
Automatic icemaker & Ice/Water Dispenser
How It Works
Your refrigerator has an automatic
icemaker and a dispenser that
dispenses water, ice cubes and crushed
ice (on some models) through
the freezer compartment
door. Here's how they work.. Water flows from
the household supply through a
(1) dual solenoid valve to the (2) water tubing and to the (3) automatic icemaker as needed_
Water is frozen in the
(4) cube mold and ejected into the (5) storage bin where a motor_powered auger moves
cubes forward Cubes dispense through the chute in the door when the
dispenser pad is pressed. When CRUSHED is selected (on some models), a baffle
channels cubes through the crusher and crushed ice falls through a chute into the glass.
Water flows through the
(6) tubing in the door and is dispensed when the pad is pressed..
(7) A light switch (on some models) turns the night light in
the dispenser on or offoThe light also comes on when the dispenser pad is pressed..
The light in the dispenser shoufd be replaced with a
7 watt maximum bulb when it burns ouL
Important Facts about Your Ice & Water Dispenser
If this is your first icemaker you'll hear occasional sounds that may be unfamiliar. These are normal
icemaking sounds and are not cause for concern,
Your icemaker will produce eight cubes per cycle, approximately 120 cubes in a 24-hour period- depending on freezer compartment temperature, room temperature, number of door openings and other use
conditions.
Intermittent dispensing of ice is normal. If ice flow interruption is more than brief, ice clump(s) may be the
cause and should be removed following instructions in this section.
Avoid over filling glasses with ice and using narrow or extra4all glasses. This can jam the chute
or cause the door in the chute to freeze shuL
Periodically open the freezer compartment door and look down into the chute. If ice isblocking the chute, poke it through with a wooden spoon,
- To help keep bits of ice from being sprayed
beyond the glass, place the glass close to the ice
chute-but not so close that it blocks out coming ice
Beverages and foods should not be quicbchilled in the ice storage bim Cans, bottles or food packages in the storage bin may cause the icemaker or auger to jam
" Do not add ice from trays or bags to the storage
bin. tt may not crush or dispense welt.
Before Using Your Icemaker and Dispenser
If you useyour refrigerator before the
water connection is made, raise the
ice access door and make sure the icemaker feeler arm is in the STOP
(up) position.. When the water supply has been connected to the icemaker,
move the feeler arm to ON (down) position
\' , ..y._ , eeler arm in Feeler arm in
STOP (up) ON (down) position position
At first there will be a delay before water isdispensed and ice is made
On mode& with awater dispenser, if no water is dispensed when the refrigerator isfirst installed, there may be air in the water line system. Pressthe dispenser
pad for at least two minutesto remove trapped air from the water Iine and to fill the water system.
Push the dispenser pad until the water line is filled
Theice cube mold will automatically fill with water AFTER cooling to freezer temperatures The firstcubes normaffy
freeze after several hours, NOTE: With a newly-installed refrigerator, allow about
24 hours for the freezer compartment to get cold enough to make ice_
(continued next page)
Automatic Icemaker & Ice/Water Dispenser (continued}
Once Your Icemaker & Dispenserare in Operation
Throw away thefirstfew batchesof icecubes (16 or 24 cubes) Thiswil! flushaway anyimpuritiesin thewater line.Do thesame
thinga[ler vacations or extended periods when ice isn'tused
To clean out the line, pour the first six glassfuls of water in the
kitchen sink The first water through the systempicks up a slight "plastic" taste from the water tubing,
To make sure the bin fills with ice, level the cubes
occasionally. When cubes fall into the bin they may pile up close to the icemaker and pushthe feelerarm to the STOP(up) position before the bin gets full, Keeping the cubes level
allows the icemaker to fill the bin_
To Dispense Ice and Water
Select CUBES,CRUSHED ICE(on somemodels) or WATER. o Grip lhe glass or other container near the rim and press
the rim against the center of the dispenser pad.
When Dispensing Ice:
Some crushed ice may be dispensed even though you
selected CUBES. This happens occasionally when a few cubes
get channeled to the crusher..
o Sometimes a mound of snow will
form on the door in the ice chute This condition isnormal, and usually occurs when you
have dispensed crushed ice repeatedly. Thesnow will eventually evaporate.
o Sometimes crushed ice will spray beyond the glass.
To avoid this, hold the glass up close to the chute,
When Dispensing Water:
o The first glass of water dispensed
may be warmer than the following ones. Thisis normal.
Dispensed water is cool, not iced.
Forcolder water, simply add crushed ice or cubes before
dispensing water.
CAUTION: Never put fingers or other
objects into the dispenser opening.
To Stop Dispensing
Release pressure Fromthe dispenser
pad and wait a few seconds to catch the last bits of ice or drops of water, There may be somedripping after
dispensing of crushed ice or water, If
there is a lot of dripping, the spill
should be wiped dry right away.. Do not pour water in the
spill shelf because it isnot self draining-pour it in the kitchen
sink,The shelf and itsgrille should be cleaned regularly
according to Care and Cleaning instructions..
The grille is easily removed by pressing on the back right corner
Press here to -3
remove grille
if Ice Clumps Form in the Storage Bin,,.
The icemaker ejects cubes in groups of eight, and it is normal for several cubes to be joined together, However, if you don't usethe ice very often ice clumps may form in the storage bin and can clog the dispenser., If this happens:
o Remove the storage bin from the freezer. o Break up ice clumps with your hands.,Throw away any
clumps that you can't break up,,
Replace the bin before the remaining cubes melt and fuse together.
To Remove Ice Storage Bin
Liftthe left corner to free the bin from
the shelf, Pull the bin straight out while supporting it at front and back.
To Replace Ice Storage Bin
Slide the bin back until the tab on the bin locks into the slot in the shelf
If the bin does not go all the way back, remove it and turn the drive
mechanism I/4 turn° Then push the bin back again until the tab on the
bin locks into the slot in the shelf.
Drive
Mechanism
If Ice Is Not Used Often...
"Old" ice cubes will become cloudy and taste state, Empty
ice storage bin periodically and wash it in lukewarm water.
Be sureto allow storage bin to coot before replacing it-
otherwise ice cubes will stickto the metal auger.
Move Feeler Arm to STOP (up) Position when,o,
Home water supply is to be turned off for several hours
° Ice storage bin isto be removed for a period of time. ° Going. away on vacation, at which time you should also
turno!t thevalve inthewater supply line to your refrigerator..
o Moving the FreshFood control to the OFF position.
Ice Service
Icemaker Water Line Installation Requirements
You will need a shutoff valve, two
1/4" OD compression nuts, two
compression sleeves and enough
1/4" O,D_ copper tubing to connect refrigerator to water source, (Your Sears Store or Catalog Sales Office
has a kit available with a saddb- type shutoff valve and copper
tubing. Before purchasing, make sure a saddle-type valve complies
with your local plumbing codes) CAUTION: Do notinstall icemaker tubing in areas where temperatures
fall below freezing
1, Find a 3/8" (10 ram) to I"
(25 mm) vertical COLD water pipe near the refrigerator When it is necessary to connect into a
horizontal water pipe, make the connection to the top or side, rather
than at the bottom to avoid drawing off any sediment from the water pipe
2. Measure from INLET on rear of refrigerator to water pipe, Add
7' (2 m) to allow for moving
refrigerator for cleaning. This isthe
length of 1/4" O D. copper tubing you will need for the job (length
from water valve to water pipe
PLUS7' [2 m]) Besure both ends of copper tubing are cut square_
3. Turn OFF main water supply Turn on nearest Faucetfang enough
to clear fine of water
CAUTION: When using any
electrical device (such as a power
drill) to facilitate installation, be
sure the device is insulated or wired
in a manner Io prevent the hazard
of electrical shock
4. Using a grounded drill, drill a
3/16" hole in the vertical cold
water pipe you have selected,
Typical ways to
connect to water
supply
Throughfloor
to basemenl cold wa_er pipe
Undersinkto coldwater
pipe
WASHER
SHUTOFF
VALVE
PIPE
I PIPE
5_ Fasten shutoff valve to cold water
pipe with pipe clamp, Be sure inlet end is solidly in 3/t 6" drilled hole
in water pipe and washer is under pipe clamp, Tighten packing nut,
Tighten pipe clamp screws carefully and evenly so washer makes a
watertight connection, Do not overtighten or you may crush copper tubing, especially if soft copper tubing isused Now you are
ready to connect the copper tubing
i
COMPRESSION
SHUTOFF
VALVE _
PACKINGNUT /
OUTLET
VALVE
SLEEVE
6o Slip compression sleeve and compression nut on copper tubing as shown above, insert end of
tubing into outlet end squarely as far as it will go, Screw compression nut
to outlet end with adjustable
wrench Do not overtighten, Turn
ON main water supply and flush out tubing until water is clear, Turn OFF shutoff valve on water pipe You are
now ready to connect other end of
1/4" copper tubing to water vatve
on back of refrigerator,
Throughwall Incrawl
to utility room space under
cold water pipe house
1/4" TUBETO SHUTOFF
VALVE
1/4" COMPRESSION
NUT
TUB|NG CLAMP
REFRIGERATORCONNECTION
7. The water valve (supplied in the icemaker kit, if not already on your model) has a compression fitting
protruding through the compressor compartment cover at the rear of the refrigerator, Assemble compression nut on compression fitting as shown above Insert end of tubing intoconnector and tighten compression nut, Be sure end of
tubing is square in connector and is inserted as far as it will go Do not overtighten, Be sure there isenough extra tubing (coiled into three turns
of about 10" [25 cm] diameter) to allow refrigerator to move out from
wall after installation Secure tubing in metal clamp at top right corner of
compressor compartment cover,
8. Turn shutoff valve ON TIGHTEN ANY CONNECTIONS OR NUTS THAT LEAK.
9_ Copper tubing may now be fastened to baseboard.
10o Your ice cubes can only be as
fresh-tasting as the water that
produces them That's why it isa
good idea to purify the water with a water filter The water Filteris an
optional part at extra cost and is available from the Sears Service
Center, Order Filter No 978488
and install at the inlet water tube
connection
11. Water Pressure Limitations:
Not below 15 PS.I. or above
125 P.S,I, if a problem occurs, call
your Utility Company
IMPORTANT: It may take up to 24 hours for your icemaker to begin
producing ice
The first few batches of ice cubes
should be thrown away, so that remaining impurities in the water
line will be flushed ouL
9
Adjusting the Controls
Food Storage Suggestions
FREEZER cONTROL _'_' ,_4_r_= _r_ _al_ FRESH FOOD CONTROL / |
COLD" " _JF_A_ COLDEST O_F COLD INITIAL CO LDE:S'3"
SEt_NG Sk'T[1NG
Two controls let you regulate the temperature in the fresh food and freezer compartments,,
At first,set both controls at "tNITtAL SET['ING" Allow 24 hours for the temperature to stabilize,
whether you are setting the controls for the first time or adjusting them later_Then, if you want colder or warmer temperatures in either compartment, adjust the controls one step at a time
NOTE: Moving the fresh food control to OFF turns off cooling in both compartments-fresh food and freezer- but does not shut off power to the refrigerator..
How to Test Temperatures
Use the milk test for the fresh food compartment. Place a container of milk on the top shelf in the fresh food compartment. Check it a day later, tf the milk is too warm or too cold, adjust the temperature controls_
Use the ice cream test for the freezer compartment. Place a container of ice cream in the center of the freezer
compartment_ Check it after a day. If it's too hard or too soft, adjust the temperature controls,.
Turning Your Household Thermostat
Below 60°F, (16°C) at Night?
You may want to move the Freezercontrol one step colder. Cooler temperatures in the house may cause the compressor to operate less frequently, thus allowing the freezer compartment to warm somewhat.
To protect your frozen food supply, leave your freezer control at this new, colder setting for the entire winter or for as long as you keep your thermostat turned down_
Moving the freezer control to a colder setting should have no effect on your fresh food compartmenL However, if
freezing occurs, move the control one step warmer_r When you stop turning the household thermostat down at
night, move the refrigerator temperature controls back to their regular settings_
Suggested Storage Times
1
Eating quality drops after time shown
Fresh Meats
Roasts (Beef & Lamb} .....................
Roasts (Pork& Veal) ........................
Steaks (Beef) ...............................
Chops (Lomb) ................................
Chops (Pork) ....................................
Ground & Stew Meats ................
Variety Meats ...................................
Sausage (Pork} ................................
Processed Meats
Bacon ...............................................
Frankfurters .....................................
Ham (Whole} ..................................
Ham (Half} .......................................
Ham (Slices} ..................................
Luncheon Meats ...............................
Sausage (Smoked) .............................
Sausage (Dry & Semi-Dry) ............ 14 to 21
Cooked Meats Cooked Meats and
Meat Dishes ............................. 3 to 4
Gravy & Meat Broth .................... 1to 2
Fresh Poultry
Chicken & Turkey (Whole) .............. 1to 2
Chicken (Pieces) ................................ 1to 2
Turkey (Pieces) ................................. 1 to 2
Duck & Goose (Whole) ............... 1 to 2
Giblets ............................................... 1 lo 2
Cooked Poultry
Pieces (Covered with Broth} ........ 1 to 2
Pieces (Not Covered) .................. 3 to 4
Cooked Poultry Dishes ................... 3 to4
FriedChicken ........................................3 to 4
(Other than for meats & poultry)
Most fruitsand vegetables ................................ 8-12 months
Leanfish ......................................................... 6-8 months
Fatty fish, rolls and breads,
soups, stew, casseroles .....................................2_3months
Cakes, pies, sandwiches,
leftovers (cooked),
Ice cream (original carton) .................................1monlh max,
Meats, fish and poultry purchased from the store vary in quality and age; consequently, safe storage times in your refrigerator will vary_
New techniques are constantly being dave}aped Consult the College or County Extension Service or
your local Utility Company for the latest information on freezing and storing foods
DAYS MONTHS
REFRIGERATOR FREEZER
35 ° to 40°F. O°F.
(2 ° to 4°C_) (-18°CJ
3to5 6to12 3 to 5 4 to 8 3to5 6to 12
3to5 6to9 31o5 3to4
! to2 3to4 1to2 3to4
t to2 i_to2
3to5 1to2
3 to 5 Freezing
IN iN
AT AT
7 1 7 1/2
7 ] to2
3 1 to2
7 nol recom-
mended,
2t03 2to3
12
9 6
6 3
6
1
4to6
4
FREEZER
10
Fresh Food Storage Tips
For Convenience_
To store unfrozen meats, fish and poultry:
o Always remove store wrappings
Rewrap in foil, film or wax paper and refrigerate
immediately,
To store cheese, wrap wet1 with wax paper or
aluminum foil, or put in a plastic bag
o Carefully wrap to expel air and help prevent mold ° Store pre-packaged cheese in its own wrapping if
you wish
To store vegetables, use the vegetable drawers-
they've been designed to preserve the natural moisture and freshness of produce,
Covering vegetables with a moist towel helps
maintain crispness
o As a further aid to freshness, pre-packaged vegetables
can be stored in their original wrapping,
Tips on Freezing Foods
There are three essential requirements for efficient home freezing
1. Initial quality. Freeze only top-quality foods Freezing retains quality and flavor; it cannot improve
quality,
2. Speed° The quicker fruits and vegetables are frozen after picking, the better the frozen product will be. You'll save time, too, with less culling and sorting to do
3_ Proper packaging. Use food wraps designed especially for freezing; they're readily available at
most food stores
o Store like lhings together_ This saves both time and
electricity because you can find Foods faster,
o Place the oldest items up front so they can be used
up promptly
° Use the bins on the door for most often used sauces
and condiments
° Use the meat drawer for meats you do not freeze,
To Save Money in Energy and Food Costs_..
o Cover moist foods with tight lids, plastic film or foil
o Leaf vegetables and fruits placed in drawers will last longer when stored in closed plastic containers or wrapped in plastic film
° Do not overload your fresh hod or freezer compartment with a lot of warm food at one time.
e Open the door the fewest times possible to save electrical energy,
o When going out of town for several days, leave as few perishables as possible in the refrigerator.
Move the icemaker feeler arm to the STOP (up)
position and shut off water supply to the refrigerator
To freeze meat, fish and poultry, wrap well in
keezer-weight foil (or other heavyoduty wrapping material) forming it carefully to the shape of the contents This expels air Fold and crimp ends of the package to provide a good, lasting seal
Don't refreeze meat that has completely thawed; meat, whether raw or cooked, can be frozen
successfully only once
To store ice cream-Fine-quality ice cream, with
high cream content, will normally require slightly lower temperatures than more "airy" already- packaged brands with low cream content
a It will be necessary to experiment to determine the
freezer compartment location and temperature control setting to keep your ice cream at the right serving temperature.
The rear of the freezer compartment is slightly
colder than the front
tl
Convenience Center Shelves
The Convenience Center consists of an automatic icemaker, an ice& water dispenser and a special
compartment with itsown door that becomes o counter when you open it. Frequently used items stored on the fresh food door are readily accessible through the Convenience Center Compartment door without having to open the main refrigerator door. An extra counter-high work surface with
its own light becomes available right at the refrigerator when the Convenience Center Compartment door is
opened. (NOTE: Be sure to close the door after use.) The work surface on the Convenience Center counter is
durable, stain- and scratch-resistant, but do not use it as a cutting board. Sharp utensils can damage it,
Cold air entering from the freezer compartment keeps the temperature in
the Convenience Center Compartment at proper
food-keeping levels. The Convenience Center
Compartment is also accessible through a lift- up door on the inside
of the fresh food compartment door. To remove the
Convenience Center door bin, open the outer
door to free the lip on the bin from the
overlapping door. Then raise the inner
door and lift the bin straight up until hooks
on bin come out of tracks on door.
NOTE: The Convenience Center door bin mustbe
replaced in its original position.
Adjustable Shelves
Shelves in the refrigerator are adiustable. Place them in the best position for your foods.
To remove a shelf: _ _1 Liftup _ []
Tilt the shelf up at front, ,.'"-'and out
then Iift it up and out of
the tracks on the rear wall.
To replace a shelf:
With the shelf front raised
slightly, put the top hooks in
the trackson the rear wall.
Then lower the front of the shelf
untiI it locks into position.
I _ TIllup
Spillproof Shelves
Spillproof shelves have
special edges to help
prevent spills from dripping
to lower shelves.
These shelves slide out for
easy access.. Make sure
you push the shelves all
the way back in before
closing the door.
Spillproof shelves slide out for easy access,
Removable Door Bins
To remove bin: Liftthe bin
straight up until the mounting hooks come out of the tracks.
To relocate bin: Place
the hooks in the slots and
push down until the bin locks in place
Dividers
Divider
Dividers can be moved
from side to side to keep
items secure so they won't
tip, spill or slide
Removable Freezer Basket Shelves
Shelves in the Freezer will stop before coming all the way out of the freezer to hetp prevent
contents from spilling onto the Floor. They can be removed easily by lifting up slightly and pulling past the "stop" location.
12
Handi Dishes
Cooking-serving-storage dishes with durable see-
through lids fit into a
rack that hangs on and can be relocated on the fresh
food compartment door Dishes and lids are safe for use in microwave ovens,
refrigerators, freezers, and are dishwasher_safe The dishes should not be used for cooking high-fat foods such
as bacon and high-sugar foods such as candy and syrup
The high temperatures of the fat and sugar can cause
bubbles to form on the inside of the dishr CAUTION: Dishes and lids are not designed for use in
the regular oven, on the range-top or in the broiler Such use can be hazardous
Removable Wine Rack
The wine rack holds a bottle on its side and
will fit on any shelf To move it, pull it straight out, position its lip over either edge of the shelf, and push
it all the way in
Storage Drawers
Temperature Controlled Meats Drawer
(on some models)
The Temperature Controlled Meats Drawer has its own cold air duct to allow a stream of cold air from the freezer
compartment to flow around the drawer The variable temperature control regulates the air Flow
from the freezer compartment Set control lever down to
the coldest setting to store fresh meats if lever isleft
in meat position for a long
period of time, some frost may form on the inside of
the drawen Set control lever up to convert the drawer to normal
refrigerator temperature and provide extra vegetable storage space Cold air duct isturned off Variable settings belween these extremes can be selected
setting
..,_._ ormal
Coldest setting
Deli Pan
The Deli Pan can be
moved within the refrigerator The sealed
drawer keeps high humidity for storage
of meats and cheese, bacon, hors d'oeuvres,
spreads and snacks
Sealed Crisper Drawer
This sealed drawer /o
isdesigned to keep unwrapped foods fresh
by retaining the natural moisture content of foods
such as:
"Artichokes
Asparagus
Beets, topped
Blueberries
Carrots
As in any refrigerated storage area, foods with strong odors should be stored wrapped-foods such as:
" Brussels Broccoli Cauliflower Turnips
Sprouts - Cabbage Green Onions - Parsnips
Celery " Lettuce Radishes " Cherries Parsley Rhubarb
Corn Peas, green - Spinach
- Currants " Plums - Tomatoes, ° Greens, leafy ripe
Adjustable Humidity Drawers (onsome models)
These drawers have individual, adjustable humidily controls that let you regulate the amount of moisture
retained in foods Slide the control all the
way to the "High" setting ._, ............. _,_
and the drawer provides high humidity
recommended for most vegetables
Slide the control all the way to the "Low" setting to provide lower humidity levels recommended for most fruits
Hurnldlt 9 Con_olle,_ Crisper
13
Care and Cleaning
Outside
The Convenience Center door-Important-use a damp
cloth to clean the outside surface of this door Do not wax the Convenience Center door_
Electronic alert and diagnostic system panels° Clean the panels on the outside and inside of the freezer
compartment door with a soft, clean cloth lightly dampened with water. Do not use cleaning sprays or large amounts of water-the liquid can run down and damage the control mechanisms.
The water and ice dispenser spill shelf should be wiped dry immediately to prevent spotting._Water left on
the shelf may leave deposits that you can remove by soaking in undiluted vinegar_ You can also use a paste of
non-precipitating water softener (such as Calgon brand)
and water, or one teaspoon (5 ml) of citric acid powder
per pint (500 ml) of hot tap water.. Soak until the deposit
disappears or becomes loose enough to rinse away
Usually 30 minutes soaking time is adequate Avoid using wax on the spill shelf and trim
The soft door handles are easy to clean if they are waxed every few months. Use a household wax such as
Pledge brand or jubilee brand to coat the handles. Soil
will then easily wash off with dish detergent and water or
a non-abrasive all-purpose cleaner Keep the finish clean. Wipe with a clean cloth lightly
dampened with kitchen appliance wax or mild liquid dishwashing detergent_ Dry' and polish with a clean, soft cloth. Do not wipe the refrigerator with a soiled
dishwashing cloth or wet towel. These may leave a residue that can harm the paint. Do not use scouring pads, powdered cleaners, bleach or cleaners containing bleach because these products can scratch and weaken the paint finish.
Protect the paint finish. The finish on the outside of the refrigerator is a high quality, baked-on paint finish.,With
proper care, it will stay new-looking and rust-free for years, Apply a coat of kitchen/appliance wax when the
refrigerator is new, and then at least twice a year
The dispenser pad (on some models) can be cleaned
by using a warm water and baking soda solution-about
a tablespoon ( t 5 ml) of baking soda to a quart ( 1 L)of water, Rinse thoroughly with water and wipe dry_
Inside
Convenience Center compartment door-inside.
Wipe up spills right away Useone tablespoon (I 5 ml)
of baking soda in one quart (1 L)of water to clean the
inside door surface, convenience center bin and inside
access door Rinse, wipe dry
The fresh food and freezer compartment interiors
should be cleaned at least once a year Unplug the
refrigerator before cleaning. If this is not practical, wring
excess moisture out of sponge or cloth when cleaning
around switches, lightsor controls.
Use warm water and baking soda solution-about one
tablespoon (15 ml) of baking soda to one quart (1 L} of
water_ This both cleans and neutralizes odors Rinse
thoroughly with water and wipe dry.
Other refrigerator parts-including door gaskets, meat and
vegetable drawers, ice storage bin and all plastic parts-
can be cleaned the same way,. Do not use cleansing
powders or other abrasive cleaners, Door gaskets are
factory-lubricated with petroleum jelly on the hinge side If
the lubricant isexcessive, wipe it off but leave a thin film on
the gasket to help insure a proper hinge-side seal, When
you clean thedoor gaskets, relubricate them
Avoid cleaning cold glass shelves with hot water
because the extreme temperature difference may
cause them tobreak..
To help prevent odors, leave an open box of baking soda
in the rear of the refrigerator, on the top shelf. Change the
box every three months In addition, put an open box of
baking soda in the freezer to absorb stale freezer odors,
Do not wash any plastic parts from your
refrigerator in your automatic dishwasher. i
Handi Dishes and lids can be cleaned in an automatic
dishwasher, or by hand with liquid dishwashing
detergent and water. You can remove stains by soaking
them in a bleach-and-water solution-one part chlorine
bleach to three parts water. (Stubborn stains may require
two or more hours of soaking.) Use a plastic scouring
pad to remove burned-on soil..Do not use cleansing powders or other abrasive cleaners.
14
Drawer Removal
Light Bulb Replacement
Drawers will stop before coming all the way out of the
Drawer H_J_
refrigerator to help prevent contents from spilling onto
the floor. Drawers can easily be removed by tilting up
guide7 !
slightly and pulling past "stop" location,
On some models you may need to remove the door
When replacing the drawers
make sure you slide them
through the drawer guides
on the left side.
bins from the fresh food door before removing the drawers
tf the door prevents you from taking out the drawers, the refrigerator will need to be rolled brward until the door
opens enough to slide the drawers out. In some cases when you roll the refrigerator out you will need to move
the refrigerator to the left as you roll it out
Drain Opening in Freezer Compartment
When cleaning, remove ! the freezer bin and flush a
solution of baking soda (one
teaspoon [5 roll) and two
cups (500 ml) of hot (not boiling) water through the
drain line with the help of a meat baster, This will help
eliminate odor and reduce the likelihood of a clogged drain line,
If drain becomes clogged, use a meat baster and baking- soda_and-water solution to force the clog through the
drain line.,
Behind Refrigerator
Take care moving your refrigerator away from the wall.
All types of floor coverings can be damaged, particularly cushioned coverings and those with embossed surfaces. Pull the refrigerator straight out and return it to position by pushing it straight in. Moving refrigerator in a side direction may damage floor covering or refrigerator,
When pushing the refrigerator back, make sure you don't roll over the power cord or icemaker supply line,,
Und er Refrigerator
The condenser is located behind the base grille For most
efficient operation, remove the base grille (see page 3) and
sweep away or vacuum up dust that is readily accessible_
For best results, use a brush
specially designed for this purpose, It isavailable at your Sears store or service centen This easy cleaning operation should be done at least once a year,
Clean the condenser coils at least once a year
Unplug refrigerator before changing a light bulb. Fresh Food Compartment-Upper Light
1, Pull off temperature
control knobs, Pin
2. Pull the bottom of the light shield down and
forward, then rotate the top up and off,
After replacing with same size bulb, reinstall
light shield, Fresh Food Compartment--Lower Light (onsomemodels)
This light islocated behind the top drawer or right above the top drawer (depending on your model),
1, Unplug the refrigerator,
2. If the light is behind the top drawer you will need to remove the drawer and the shelf above it,,To remove the
drawer see the Drawer Removal section in Care and
Cleaning,
To remove the shelf first
remove any food on the shelf
Then tilt the shelf up at the
Frontand lift it up and out
of the tracks, 3o Grasp the bottom of
the light shield and pull it
forward and up.
4. After replacing with the same size bulb, replace the shield. If you cannot locate the correct bulb, see your dealer
5_ Ifthe tight was behind the top drawer, you wil! need to replace the drawer and the shelf above it,
To replace the shelf, raise the shelf front slightly and
place the top hooks in the lowest large track slots. Then lower the front of the shelf until it is level,
6. Plug the refrigerator back in
Freezer Compartment
1. Remove shelf justbelow light panel, (Shelf will be easier to remove if it is emptied first,)
2. Pul!plastic light panel toward you (It wil! bend to free tabs from grooves,)
3. After replacing with same size bulb, reinstall panel and shelf,
Convenience Center
1. Remove top door bin and raise Convenience Center
inner door,
2. Presssides of flexible light panel to release locking tabs and allow the panel to swing down
3. After replacing with nightJight bulb of same wattage,
place rear tab of light panel into door and rotate panel up until tabs lock into slots above,
t5
1!_
Before You Call for Service
Save time and money Check this listof causes of minor operating problems you can correct yourself
No panel touch pad response
If interior light is not on, refrigerator may not be plugged in atwall outlet
If plug is secure and refrigerator fails to operate, plug lamp into same outlet to determine if there istripped
circuit breaker or burned_out fuse
Refrigerator does not operate
May be in defrost cycle when motor does not operate
for about 30 minutes
Temperature control in OFF position Motor operates for long periods
Modern refrigerators with more storage space and a larger freezer require more operating time,
Normal when refrigerator is first delivered to
your home-usually requires 24 hours to completely
cool down
Large amounts of food placed in refrigerator to be cooled or frozen,
Hot weather-frequent door openings
- Door left open
Temperature controls set too cold
Condenser needs cleaning
Operating sounds
The high speed compressor motor required to
maintain near zero temperatures in the large freezer compartment may produce higher sound levels than
your old refrigerator
Normal fan air flow-one fan blows cold air through
the refrigerator and freezer compartments-another fan cools the compressor motor
These NORMAL sounds will also be heard from
time to time:
Defrost timer switch clicks at defrost . Defrost water dripping
. Temperature control clicks ON or OFF
Refrigerant boiling or gurgling
Cracking or popping of cooling coils caused
by expansion and contraction during defrost and refrigeration following defrost,
- Ice cubes dropping into the bin and water running in pipes as icemaker refills
Motor starts & stops frequently
Temperature control starts and stops motor to maintain even temperatures This isnormal
Door not closing properly . Door gasket on hinge side sticking or folding over
To correct, put a small amount of petroleum jelly on face
of gasket
Vibration or rattling . If refrigerator vibrates, more than likely it is not resting
solidly on the floor The front roller screws need adiusting, or floor is weak or uneven Refer to Starting Your Refrigerator section
. If dishes vibrate on shelves, try moving them Slight vibration is normal
Foods dry out
Foods not covered, wrapped or sealed properly_
Fresh food or freezer compartment temperature too warm
Temperature control not set cold enough
Warm weather-frequent door openings
Door left open for long timex
Package may be holding door open_ Frost or ice crystals on frozen food
Door may have been left ajar or package holding
door open,
Too frequent or too long door openings . Frostwithin package is normal,
Slow ice cube freezing
Door may have been left ajar
Set temperature of freezer compartment colder,
Ice cubes have odor/taste
"Old cubes need to be discarded, Empty ice bin
every 30 days
Ice storage bin needs to be washed
Unsealed packages in refrigerator and/or
freezer compartments may be transmitting odor/taste to ice cubes
Interior of refrigerator needs cleaning
Automatic icemaker does not work
lcemaker feeler arm in STOP (up) position . Water supply turned off or not connected
Freezer compartment too warm
Cubes too small-water shutoff valve connecting
refrigerator to home water line may be clogged_
Sometimes cubes fuseto the side of the ice mold and hold the feeler arm in the STOP (up) position, Remove this
ice to restart the icemaker . Piled up cubes in storage bin may cause icemaker to
shut off prematurely With icemaker feeler arm in STOP (up) position, level cubes in bin by hand
When leveling cubes by hand, you may have pushed
the feeler arm into the STOP (up) position by mistake
16
Accessories
No icecubes
- Remove storage container.. If cubes are frozen to wire arm, remove cubes.
lcemaker or water supply turned off. Cube dispenser does not work
, Irregular ice clumps in storage container. Break up as
many as you can with fingertip pressure and discard the remaining clumps_
Water has poor taste/odor
- tf water dispenser has not been used for an extended period, dispense several glassfuls of water to eliminate taste temporarily imparted by the water line.
Poor-tasting incoming water, install a water filter Water dispenser does not work
° Water supply line turned off or not connected.
- Supply line may be clogged with sediment
If no water is dispensed when the refrigerator isfirst
installed, there may be air in the water system. Pressthe dispenser pad for at least two minutes to remove trapped
air from the water line and to fill the water system. Moisture forms on outside of refrigerator
° Not unusual during periods of high humidity Moisture collects inside
Too frequent or too long door openings..
In humid weather, air carries moisture into refrigerator
when doors are opened Water on floor
. The drain in the bottom of the freezer may be clogged
Remove any ice on the freezer bottom and dean the drain. Refer to Care and Cleaning section_
Hot air from bottom of refrigerator
- Normal air flow cooling motor In the refrigeration process, it isnormal that heat be expelled in the area under the refrigerator_ Some floor coverings will discolor at these normal and safe operating temperatures. Your floor covering supplier should be consulted if you object
to this discoloration.
Interior light does not work
No power at outlet.
Light bulb needs replacing See Care and Cleaning
section_
Water Filter Accessory
(optional at extra cost) Your ice cubes can only be as fresh-tasting as the water
that produces them. That's why it's a good idea to purify the water with a water filter.
The water filter is an optional part at extra cost and is available from your Sears Service Center. Order Filter
No. 978488 and it may be installed in minutes when
attached to the inlet water tube connection..
Water Supply Accessory Kit
(optional at extra cost)
A water supply kit containing copper tubing, shut-off valve, fittings and instructions needed to connect the icemaker to your cold water line is also available from
your Sears store or Sears Service Center.
Moving Precautions
Disconnect the power cord from the wall outlet, remove aJlfood and clean and dry the interior_ Secure all loose items by taping them securely in place, Keep the refrigerator in an upright position during actual moving and in the van_ Secure the refrigerator in the van to
prevent movement, and protect the outside with a blanket,
Vacation Precautions
Forextended vacations or absences, shut off power to
the refrigerator, turnthe FreshFood control to the OFF position, and clean the interior with a baking soda solution of one tablespoon of baking soda to one quart of water. Wipe dry To prevent odors, leave an open box of baking soda inthe refrigerator._Leave the doors open_
For shorter vacations, remove perishable foods and leave controls at their regular settings_However, if room
temperalureis expected to drop below 60°F. (16°C), follow the same instructions asfor extended vacations..
Seticemaker to the STOP (up) position and shutoff water supply to refrigerator.
Refrigerator has odor
Food with strong odors should be tightly covered.
, Check for spoiled food.
Interior needs cleaning. Refer to Care and Cleaning
section
Defrost water system needs cleaning
° Keep open box of baking soda in refrigerator;
replace every three months.
17
18
Loading...
+ 42 hidden pages