Kenmore 25386050410, 25387050410, 25387050412, 25387050414, 25387050416 Installation Guide

READ BEFORE INSTALLING UNIT

OPP Window Mounting (5,000---6,500 BTU)

To avoid risk of personal injury, property damage, or product damage due to the weight of this device and sharp
edges that may be exposed:

Air conditioners covered in this manual pose an excessive weight hazard. Two or more people are needed to
move and install the unit. To prevent injury or strain, use proper lifting and carrying techniques when moving unit.
Carefully inspect location where air conditioner will be installed. Be sure it will support the weight of the unit over
an extended period of time.
Handle air conditioner with care. Wear protective gloves whenever lifting or carrying the unit. AVOID the sharp

metal fins on front and rear coils.
Make sure air conditioner does not fall during installation.

f

Mounting Hardware

Qty.

• SAVE CARTON and these INSTALLATION
INSTRUCTIONS for future reference. The carton is

the best way to store unit during winter, or when not

in use.

e DO NOT USE ANY SCREWS OTHER THAN

THOSE SPECIFIED HERE.

• FOR SAFETY REASONS, THE TOP RAIL MUST BE

SECURELY FASTENED WITH ALL FOUR (4)
SCREWS.

Some assembly is required. Please read these instructions
carefully.

,.. J

Top Rail Hardware Qty.

3/8" Screw 4

Top Rail 1

• Philips Screwdriver

• Drill (If pilot holes are needed)

Before installing, the top rail must be assembled on the unit.

A. Remove the air conditioner from the carton and place on a flat surface.

B. Remove top rail from the rear of the packaging material as shown in Fig. A
C. Align the hole in the top rail with those on the top of the unit as shown in Fig. B
D. Secure the top rail to the unit with the 3/8" Screws as shown in Fig. C

screws

1/2"

lock frame

(For Wooden windows)

lock frame

(For Vinyl-Clad windows)

sash lock

weather seals

(6"x3/4"x1/12")

window sash seal foam

TOOLS NEEDED

7

2

2

5

Top Rail Fig. A Fig. B

Packaging

2020211A2576

LEFT + RIGHT FILLER PANEL ASSEMBLY

NOTE: Top Rail and Side Panels at each side are offset to provide the proper pitch to the rear of (5/16").

This is necessary for proper condensed water utilization and drainage. If you are not using the Side Panels
for any reason, this pitch to the rear must be maintained!

Place unit on floor, a bench or a table. There is a Left and Right side Filler Panels - be sure to use the proper
panel for each side. When installed, the flange for securing the panel in place to the window sill will be facing

into the room.

A. Hold the side Panel in one hand and gently pull back the center to free the open end. See FIG. 1.

B. Slide the free end "T" section of the panel directly into the cabinet as shown in FIG. 2. Slide the panel down. Be
sure to leave enough space to slip the top and bottom of the frame into the rails on the cabinet.

C. Once the panel has been installed on the side of the cabinet, make sure it sits securely inside the frame channel by
making slight adjustments. Slide the top and bottom ends of the frame into the top and bottom rails of the cabinet. See

D. Slide the panel all the way in and repeat on the other side.
FIG. 3.

FIG. 1 FIG. 2 "T" section FIG. 3 Top Rail

Bottom Rail

Your air conditioner is designed to install in standard double hung windows with opening widths of 23 to 36 inches
(584 mm to 914 mm) (FIG. 4A _ FIG. 4B).
Lower sash must open sufficiently to allow a clear vertical opening of 13 inches (330 mm ). Side louvers and the rear of
the air conditioner must have clear air space to allow enough airflow through the condenser, for heat removal. The rear
of the unit must be outdoors, not inside a building or garage.

Fig. 4A Fig. 4B

OFI ;ET

EXTERIOR EXTERIOR

WALL 23" to36'

• ,0 11L

rain f_ _ _

Wooden Windows Vinyl-Clad Windows

Storm Window:

FIG. 5

If the air conditoner is blocked by Storm Window, add wood as
shown in FIG. 5, or remove storm window before air conditioner

is installed.
If Storm Window Frame must remain, be sure the drain holes or

slots are not caulked or painted shut. Accumulated Rain Water
or Condensation must be allowed to drain out.

Storm window
frame or other

obstruction. (38 mm)

1-1/2" min

Board

thickness as

required, for
proper pitch to

_' rear, along

entire sill.

_' Fasten with

nails or screws.

Keepafirmgripontheairconditioner,carefullyplacetheunitintothewindowopeningsothebottomoftheair
conditionerframeisagainstthewindowsill(FIG.6A&FIG.6B).Carefullyclosethewindowbehindthetoprail

oftheunit.

FIG. 6A I I FIG. 6B

I I

__1

I

INslDL]E

Wooden Windows Vinyl-Clad Windows

Extend the side panels out against the window frame (FIG. 7A for wooden windows), (FIG. 7B for Vinyl-Clad

windows).

FIG. 7A FIG. 7B

OUTSIDE INSIDE I OUTSIDE

Place the frame lock between the frame extensions and the window sill as shown (FIG. 8A for wooden
windows), (FIG. 8B for Vinyl-Clad windows).

FIG. 8A FIG. 8B

wooden windows:

Drive locking screws:

A: For wooden windows:

Drive 112" (12.7 mm)locking screws through the frame lock and into the sill (FIG. 9A). NOTE:To prevent
window sill from splitting, drill 118"(3mm) pilot holes before driving screws. Drive 1/2" (12.7 mm)locking
screws through frame holes into window sash (FIG. 9B).

B: For Vinyl-Clad windows:

Drive 1/2" (12.7 mm) locking screws through the frame lock and into the window sash (FIG. 9B). NOTE:
Before driving the screws, use a drill to drill 5 holes through the holes in the frame lock and frame extensions
into the windows sash as shown ( FIG. 9B).

Vinyl-Clad windows:

FIG. 9A // FIG. 9B

JJ;

To secure lower sash in place, attach right angle sash lock with 1/2" (12.7mm) screw as shown (FIG. 10).
NOTE: It is difficult to lock the windows with the sash lock for Vinyl-Clad windows, so you can use lock by

window itself.

Cut foam window seal and insert it into the space between the upper and lower sashes (FIG. 11).

FIG. 10 FIG. 11

Check that air conditioner is tilted back about 1/4" to 1/2" (tilted about 2° to 4° downward to the outside, see
FIG. 12A & FIG. 12B). After proper installation, condensate should not drain from the overflow drain hole during
normal use, correct the slope otherwise.

FIG. 12A ! I

!

__L

H--f--_Botto m Rail

about I

1/4"_1/2"1 I

Wooden Window

Trim the weather seal (6°'X3/4"X1/12 °') with a proper length,
peel off the protective backing and plug any gaps if needed

as shown FIG.13.

FIG. 12B

INSIDE OUTSIDE

_H=H1-H2 about 1/4"~1/2 ''

J:

H1Tm¢ [ H ottom Rail

-- -- ____-B

Vinyl-Clad Window

FIG. 13

Removing the air conditioner From Window

Turn the air conditioner off, and disconnect power cord.

Remove sash seal from between windows, and unscrew sash lock.
Remove screws installed through frame and framelock.

Close (slide) side panels into frame.

Keeping a firm grip on air conditioner, raise sash and

carefully remove.

Be careful not to spill any condensate water while lifting
unit from window. Store parts WITH air conditioner.

/

LEA ESTO ANTES DE MONTAR LA UNIDAD

Para evitar el riesgo de lesiones, de da_os materiales y de da_os al equipo debido a su peso y a los bordes
afilados que puedan quedar expuestos:

Los aparatos de aire acondicionado detallados en este manual suponen un peligro pot su excesivo peso.
Es necesaria la intervenci6n de dos o mas personas para mover e instalar el equipo. Para evitar lesiones y

problemas musculares, emplee t6cnicas adecuadas de levantamiento y desplazamiento del mismo.

Inspeccione cuidadosamente la Iocalizaci6n donde piensa instalar el equipo de aire acondicionado. Aseg0rese

de que es capaz de soportar el peso del mismo durante un largo periodo de tiempo.
Manipule el aparato de aire acondicionado con cuidado. Utilice guantes protectores cuando necesite levantarlo

o moverlo. EVlTE tocar las afiladas aletas metalicas que existen en el frontal yen la parte posterior.
Evite que el aparato de aire acondicionado se caiga durante la instalaci6n.

Piezas para el montaje

• GUARDE EL EMBALAJE y estas INSTRUCClONES
DE MONTAJE para futuras referencias. El embalaje
proporciona la mejor forma de guardar el equipo

durante el invierno, o cuando no se utiliza.

• NO USE OTROS TORNILLOS DIFERENTES A LOS

AQUi ESPECIFICADOS.

• POR RAZONES DE SEGURIDAD, EL RAiL

SUPERIOR DEBE ASEGURARSE CON LOS
CUATRO (4) TORNILLOS PROVlSTOS.

_ Tirasde aislamientoautoadhesivas

Es necesario realizar alg0n proceso de ensamblado.
Por favor, lea cuidadosamente estas instrucciones.

Piezas del rail superior Cant.

Tornillos de 3/8" 4

Rail superior 1

Antes de comenzar la instalaci6n, el rail superior debe ensamblarse en el equipo.
A. Saque el equipo de aire acondicionado de su embalaje y col6quelo sobre una superficie plana.

B. Extraiga el rail superior de la parte trasera del embalaje, tal como se muestra en la Fig. A
C. Alinee los agujeros del rail superior con los de la parte superior de la carcasa del equipo tal como se muestra en la Fig. B
D. Asegure el rail superior a la carcasa con los tornillos de 3/8" tal como se muestra en la Fig. C

Rail

superior

Fig. A

• Destornillador Philips

• Taladro (si es necesario hacer agujeros)

Fig. B

Placa de bloqueo para el marco

Placa de bloqueo para el marco

Placa de bloqueo para la hoja

de la ventana

HERRAMIENTAS NECESARIAS

Tornillos de 1/2"

(Para ventanas de madera)

(Para ventanas de PVC)

(6"X3/4"X 1/12")

Burlete de espuma

Cant

Embalaje

2020211A2576