Kenmore 25378989801, 25378989800, 25378984801, 25378984800, 25378983801 Owner’s Manual

...

Kenmore 25378989801, 25378989800, 25378984801, 25378984800, 25378983801, 25378983800, 25378982801, 25378982800, 25378979801, 25378979800, 25378974801, 25378974800, 25378973801, 25378973800, 25378972801, 25378972800, 25378949801, 25378949800, 25378944801, 25378944800, 25378942801, 25378942800, 25378939801, 25378939800, 25378934801, 25378934800, 25378932801, 25378932800, 25378269800, 25378264800, 25378263800, 25378262800, 25378259800, 25378254800, 25378253800, 25378252800, 25378249800, 25378244800, 25378242800, 25378239800, 25378234800, 25378232800, 25378189800, 25378184800, 25378183800, 25378182800, 25378179800, 25378174800, 25378173800, 25378172800, 25377969801, 25377969800, 2537482440J, 2537482340K, 2537482340J, 2537482240K, 2537482240J, 2537481840K, 2537481840J, 2537481440K, 2537481340K, 2537481340J, 2537481240K, 2537481240J, 2537481040K, 2537481040J, 2537480240H, 2537480240G, 2537472240A, 25374532602, 25371754801, 25371752801, 25371752800, 2537088940K, 2537088940J, 2537088940H, 2537088440K, 25368989801, 25368989800, 25368984801, 25368984800, 25368983801, 25368983800, 25368982801, 25368982800, 25368979801, 25368979800, 25368974801, 25368974800, 25368973801, 25368973800, 25368972801, 25368972800, 25368949801, 25368949800, 25368944800, 25368942801, 25368942800, 25368939801, 25368939800, 25368934801, 25368932801, 25368932800, 25368269800, 25368264800, 25368263800, 25368262800, 25368259800, 25368254800, 25368253800, 25368252800, 25368249800, 25368244800, 25368242800, 25368239800, 25368234800, 25368232800, 25368189800, 25368184800, 25368183800, 25368182800, 25368179800, 25368174800, 25368173800, 25368172800, 25366729801, 25366729800, 25366723801, 25366723800, 25366720801, 25366720800, 2536581250A, 25365812509, 2536580250A, 25365802509, 2536482440G, 2536482440F, 2536480240E, 2536480240D, 25364722408, 25364722407, 25364522405, 2536419440J, 2536419440H, 2536419440G, 2536419240J, 2536419240H, 2536419240G, 25361894802, 25361894801, 25361894800, 25361892802, 25361892801, 25361892800, 25361754801, 25361754800, 25361752801, 25361752800, 25361738804, 25361738802, 25361738801, 25361738800, 25361737804, 25361737802, 25361737801, 25361737800, 25361734804, 25361734802, 25361734801, 25361734800, 25361732804, 25361732802, 25361732801, 25361732800, 2536171740A, 25361717409, 25361717408, 25361717407, 2536171440A, 25361714409, 25361714408, 25361714407, 2536171240A, 25361712409, 25361712408, 25361712407, 25361704408, 25361704407, 25361702408, 25361502405, 2536088740F, 2536088740E, 2536088740D, 2536088440F, 2536088440E, 2536088440D, 2536088240F, 2536088240E, 2536088240D, 2536080440F, 2536080440E, 2536080240F, 2536080240E, 2533111530J, 2533111530H, 2533111330J, 2533111330H, 2537482440K, 25371754800 Owner’s Manual

Refrigerator

Top Mount

Use & Care Guide

Refrigerador

Congeiador Superior

Gufa para su uso y cuidado

R_frig_rateur

Compartiments Superposes

Guide d'utilisation et d'entretien

Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.

Sears Canada, Inc., Toronto, Ontario, Canada M5B 2B8

www.sears.com

241815201 (Sept 2007)

Congratulations on your purchase of a new refrigerator! We

here at Sears are very proud of our product and we are completely committed to providing you with the best service possible. Your satisfaction is our #1 priority.

We know you'll enjoy your new refrigerator and ThankYou for choosing our product. We hope you consider us for future purchases.

PLEASE READ AND SAVE THESE

INSTRUCTIONS This Owner's Guide provides specific operating

instructions for your model. Use your refrigerator only as

instructed in this manual. These instructions are not meant to cover every possible condition and situation that may

occur. Common sense and caution must be practiced when installing, operating and maintaining any appliance.

Please record your model and serial numbers below for future reference.This information is found on the

serial plate Jocated inside the refrigerator compartment.

Model Number: 253

or: 970

Serial Number:

Purchase Date:

FOR YOUR SAFETY

• Do not store or use gasoline, or other flammable liquids inthe vicinity of this or any other appliance. Read product labels for warnings regarding flammability and other

hazards.

• Do not operate the refrigerator in the presence of explosive fumes.

Avoid contact with any moving parts of automatic ice

maker. Remove all staples from the carton. Staples can cause

severe cuts, and also destroy finishes if they come in contact with other appliances or furniture.

CHILD SAFETY Destroy or recycle the carton, plastic bags, and any

exterior wrapping material immediately after the refrigerator is unpacked. Children should NEVER use these items to

play. Cartons covered with rugs, bedspreads, plastic sheets or stretch wrap may become airtight chambers, and can quickly cause suffocation.

PROPER DISPOSAL OF YOUR REFRIGERATOR OR FREEZER

Risk of child entrapment

Child entrapment and

Welcome & Congratulations ................ 2

Important Safety Instructions .............. 2-3

Warranty Information ........................... 3

Master Protection Agreements ........... 4

Installation--Includes Connecting Household

Water Supply to Refrigerator ............................. 5-6

Door Removal & Reversal .................. 7-9

Features At A Glance ......................... 10

Temperature Controls .......................... 11

Looking Inside ..................................... 12-13

Food Storage & Energy Saving Tips ... 14

Ice Service .......................................... 15

Normal Operating Sounds & Sights .... 16

Care & Cleaning .................................. 17-18

Before You Call .................................... 19

suffocation are not problems of

the past. Junked or abandoned

for "just a few days." If you are getting rid of your old refrigerator or freezer, please

follow the instructions below to help prevent accidents.

Before you throw away your old refrigerator/freezer:

• Remove doors.

Leave shelves in place so children may not easily climb inside.

Have refrigerant removed by a qualified service technician.

ELECTRICALiNFORMATiON

• The refrigerator must be plugged into its own

dedicated 115 Volt, 60 Hz., AC only electric outlet. The power cord of the appliance is equipped with a three-prong grounding plug for your protection against electrical shock hazards. It must be plugged directly into a properly grounded three-prong receptacle. The receptacle must be installed in accordance with local codes and ordinances. Consult a qualified electrician. Do not use an extension cord or adapter plug.

• Immediately repair or replace any power cord that becomes frayed or damaged.

• Never unplug the refrigerator by pulling on the power cord. Always grip the plug firmly, and pull straight out from the receptacle to prevent damaging the power cord.

Unplug the refrigerator before cleaning and before replacing a light bulb to avoid electrical shock.

Performance may be affected if the voltage varies by 10% or more. Operating the refrigerator with insufficient power can damage the compressor. Such damage is not covered under your warranty.

Do not plug the unit into an outlet controlled by a wall switch or pull cord to prevent the refrigerator from being turned off accidentally.

Avoid connecting refrigerator to aGround Fault Interruptor (GFI) circuit.

Groundingtype

wall receptac!e

DO not, underany circumstances,

cut_ temove_

or bypass the

Power cord with

3-prong grounded p!ug

KENIVIORE APPLIANCE WARRANTY

OneYear Limited Warranty When installed, operated and maintained according to all

instructionssupplied with the product, ifthis appliance fails due to a defect in material or workmanship within one year from the date of purchase, call 1-800-4-MY-HOME® to arrange for free repair.

If this appliance isused for other than private family purposes, this warranty applies for only 90 days from the date of purchase.

This warranty covers only defects in material and workmanship. Sears will NOT pay for:

1. Expendable items that can wear out from normal use, including but not limited to filters, belts, light bulbs and

bags.

2. A service technician to instruct the user in correct product installation, operation or maintenance.

3. A service technician to clean or maintain this product.

4. Damage to or failure of this product if it is not installed,

operated or maintained according to all instructions supplied with the product.

5. Damage to or failure of this product resulting from

accident, abuse, misuse or use for other than its

intended purpose.

6. Damage to or failure of this product caused by the use

of detergents, cleaners, chemicals or utensils other than those recommended in all instructions supplied with the product.

7. Damage to or failure of parts or systems resulting from unauthorized modifications made to this product.

Disclaimer of implied warranties; limitationof remedies Customer's sole and exclusive remedy under this limited

warranty shall be product repair as provided herein. Implied warranties, including warranties of merchantability or fitness for a particular purpose, are limited to one year or the shortest period allowed by law. Sears shall not be liable for incidental or consequential damages. Some states and provinces do not allow the exclusion or limita- tion of incidental or consequential damages, or limitations on the duration of implied warranties of merchantability or fitness, so these exclusions or limitations may not apply to you.

This warranty applies only while this appliance is used in the United States and Canada.

This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

Sears, Roebuck and Co., Dept. 817WA, Hoffman Es= tates, IL 60179

Sears Canada Inc.,Toronto, Ontario, Canada M5B 2B8

Master Protection Agreements

Congratulations on making a smart purchase, Your new Kenmore®product is designed and manufactured for years of

dependable operation. But like all products, it may require preventive maintenance or repair from time to time, That's when

having a Master Protection Agreement can save you money and aggravation,

The Master Protection Agreement also helps extend the life of your new product. Here's what the Agreement* includes:

[] Parts and labor needed to help keep products operating properly under normal use, not just defects, Our coverage

goes well beyond the product warranty. No deductibles, no functional failure excluded from coverage - real

protection.

[] Expert service by a force of more than 10,000 authorized Sears service technicians, which means someone you can

trust will be working on your product,

[] Unlimited service calls and nationwide service, as often as you want us, whenever you want us, [] "No-lemon" guarantee - replacement of your covered product if four or more product failures occur within twelve

months,

[] Product replacement if your covered product can't be fixed, [] Annual Preventive Maintenance Check at your request- no extra charge,

[] Fast help by phone - we call it Rapid Resolution - phone support from a Sears representative on all products, Think

of us as a "talking owner's manual".

[] Power surge protection against electrical damage due to power fluctuations, [] $250 Food Loss Protection annually for any food spoilage that is the result of mechanical failure of any covered

refrigerator or freezer. [] Rental reimbursement if repair of your covered product takes longer than promised. [] 10% discount off the regular price of any non-covered repair service and related installed parts,

Once you purchase the Agreement, a simple phone call is all that it takes for you to schedule service. You can call anytime day or night, or schedule a service appointment online,

The Master Protection Agreement is a risk free purchase, If you cancel for any reason during the product warranty period, we will provide a full refund, Or, a prorated refund anytime after the product warranty period expires, Purchase your Master

Protection Agreement today!

Some limitations and exclusions apply. For prices and additional information in the U.S.A. call 1-800-827-6655. * Coverage in Canada varies on some items. For full details call Sears Canada at 1-800-361-6665.

Sears Installation Service

For Sears professional installation of home appliances, garage door openers, water heaters, and other major home items, in the U.S,A, or Canada call 1-800-4-MY-HOME ®.

This Use & Care Manual provides specific operating instructions for your model• Use the refrigerator only as instructed in this Use & Care Manual• Before starting the

refrigerator, follow these important first steps.

LOCATION

o Choose a place that is near a grounded electrical outlet•

Do Not use an extension cord or an adapter plug.

o If possible, place the refrigerator out of direct sunlight

and away from the range, dishwasher or other heat sources•

o The refrigerator must be installed on a floor that is level

and strong enough to support a fully loaded refrigerator•

o Consider water supply availability for models equipped

with an automatic ice maker•

iNSTALLATiON

DOOR OPENING

Your refrigerator should be positioned to allow easy access to a counter when removing food. To make this possible, the direction in which the doors open can be reversed• See Door

Removal & Reversal Instructions.

LEVELING

All four corners of your refrigerator must rest firmly on a solid floor• Your refrigerator is equipped with adjustable front rollers or front leveling screws to help level your unit.

To LevelYour Refrigerator:

1. Remove toe grille•

2. Use flat-blade screwdriver or 3/8" socket wrench to

adjust front rollers• Use adjustable wrench [o adjust leveling screws•

• /

installation Clearances o Allow the following clearances for ease of installation,

proper air circulation, and plumbing and electrical connections:

Sides & Top 3/8" Back 1"

Adjustable Front Roller

(some models)

Raise

Stationary Front Roller

with Leveling Screw

(some models)

To Connect Water Supply LineTo ice Maker Inlet Valve

1. Disconnect refrigerator from electric power source.

2. Place end of water supply line into sink or bucket. Turn ON water supply and flush supply line until water is clear. Turn OFF water supply at shutoff valve.

3. Unscrew plastic cap from water valve inlet and discard cap.

4. Slide brass compression nut, then ferrule (sleeve) onto water supply line, as shown.

5. Push water supply line into water valve inlet as far as it will go (¼ inch). Slide ferrule (sleeve) into valve inlet and

finger tighten compression nut onto valve. Tighten another half turn with a wrench; DO NOT over tighten.

6. With steel clamp and screw, secure water supply line to rear panel of refrigerator as shown.

7. Coil excess water supply line (about 2V2 turns) behind refrigerator as shown and arrange coils so they do not vibrate or wear against any other surface.

8. Turn ON water supply at shutoff valve and tighten any connections that leak.

9. Reconnect refrigerator to electrical power source.

10. To turn ice maker on, lower wire signal arm (see ice maker front cover for ON/OFF position of arm).

Before Installing The Water Supply Line, You Will Need

,, Basic Tools: adjustable wrench, flat-blade screwdriver,

and Phillips TM screwdriver

,, Access to a household cold water line with water pressure

between 30 and 100 psi.

,, A water supply line made of ¼ inch (6.4 mm) OD, copper

tubing. To determine the length of copper tubing needed, you will need to measure the distance from the ice maker

inlet valve at the back of the refrigerator to your cold water pipe. Then add approximately 7 feet (2.1 meters), so the refrigerator can be moved out for cleaning (as shown).

,, A shutoff valve to connect the water supply line to your

household water system. DO NOT use a self-piercing type

shutoff valve.

,, A compression nut and ferrule (sleeve) for connecting the

water supply line to the ice maker inlet valve.

Copper water line from household water supply

(Include enough tubing in loop to allow

g refrigerator out for cleaning.)

Door Stop Handle

2% Boom

Scr Center ge

Hinge Screw

Scre_

Top Hinge

Door Stop ScYew.

3vet

Tools Necessary:

Phillips '' head

Quadrex r" head

screwdriver

Washer

Center

Hole

Wrench Set

DOOR REMOVAL AND REVERSAL INSTRUCTIONS:

1. Remove toe grille.

2. Remove top hinge cover. Trace around the hinge with a soft lead pencil. This makes reinstallation easier. Remove top hinge and lift door off center hinge pin. Set door aside.

3. Unscrew center hinge pin using adjustable wrench and save for reassembly. Ensure plastic washer stays on hinge pin.

4. Lift refrigerator door off of bottom hinge and set aside.

5. Remove center hinge and shim by removing inside screw and loosening two outside screws enough to allow hinge and shim to slide out. Tighten screws.

6. Loosen two outside screws on opposite side of refrigerator, remove inside screw and install center hinge.

7. Remove two screws on bottom hinge with 3/8" socket wrench.

8. Install bottom hinge on opposite side with the two screws removed from step 7.

9. Unscrew bottom hinge pin using adjustable wrench. Move hinge pin to other hole in hinge and tighten with adjustable wrench.

10. Reverse door handles (see instructions on next page).

11. Move freezer and refrigerator door stops to opposite side. Before starting screws, use an awl to puncture the foam.

12. Position refrigerator door onto bottom hinge pin and screw center hinge pin through center hinge into top of door. Close refrigerator door to help align hinge hole.

13. Tighten center hinge pin with adjustable wrench.

14. Remove cabinet and hinge hole plugs and move to opposite side.

15. Lower freezer door onto center hinge pin.

16. Close freezer door. Have an assistant lift up on opposite side of door while tightening screws to install top hinge.

17. Flip toe grille and reinstall.

18. Plug in electrical power cord and turn refrigerator temperature control to center position. Adjust setting as necessary.

TO REMOVE FREEZER HANDLE: (Handles may be easier to reverse while doors are off.)

1. Remove two screws attaching handle to bottom of freezer door.

2. Swing bottom of handle away from the door and slide handle straight up and off of dovetail button.

3. Remove screw and dovetail button and install on other side, moving hole plugs from corresponding holes to

opposite side.

TO ATTACH FREEZER HANDLE:

1. Start with handle offset away from door. Place top of handle over dovetail button, swing handle into an upright position and pull downward, locking it into place.

2. Secure bottom of handle withtwo screws removed earlier.

TO REMOVE REFRIGERATOR HANDLE: (Handles may be easier to reverse while doors are off.)

1. Remove two screws attaching handle to top of refrigerator door.

2. Swing top of handle away from door and slide handle down and off of dovetail button.

3. Remove screw and dovetail button and install on other side, moving hole plugs from corresponding holes to

opposite side.

TO ATTACH REFRIGERATOR HANDLE:

1. Start with handle offset away from door. Place bottom of handle over dovetail button, swing handle into an

upright position and pull upward, locking it into place.

2. Secure top of handle with screws. TO ATTACH TRIM:

1. Slide both trim locks out of trim.

2. Insert new adhesive trim locks contained in your literature pack.

byii

TRIM REMOVAL (FULL-LENGTH TRiM MODELS ONLY) in some models, the refrigerator door has a full length trim

piece which continues from the bottom of the handle to the bottom of the door.The top of the trim fits around the base of the handle. An adhesive '_rimlock"ispositioned about halfway down. The bottom of the trim is held in place by either an adhesive trim lock, or a trim lock with two prongs inserted

intoa hole on the face of the door. TO REMOVE TRIM:

1. Remove trim by gently pulling trim lockareas out and away from door.

2. When trim isfree from door, slide the trim straight down and away from base of handle.

3. install trim to handle by sliding over base of handle. Carefully align trim and press down at trim lock locations.

4. Replace hole plug on opposite side. Use rubbing alcohol

to remove any adhesive residue from old trim lock

locations.

Lock Handb

Handle Over

Dovetail

Dovetaim

Adhesive

Lock

Full

Trim

TO REMOVEREFRIGERATORHANDLE: (Handlesmaybeeasiertoreversewhiledoorsareoff.)

1. Removetwoscrewsattachinghandletotopof refrigeratordoor.

2. Slidehandlestraightupandpullhandleoffdovetail screwondoor.

3. Removedovetailscrewfromdoorandinstallonother side,movingholeplugsfromcorrespondingholesto

oppositeside.

TO ATTACHREFRIGERATORHANDLE:

1. Placetopofhandleoverdovetailscrew,pullhandle straightdownuntilhandleisalignedwithscrewholeson topofdoor.

2. Securetopofhandlewithtwoscrewsremovedearlier.

TO REMOVEFREEZERHANDLE:

(Handlesmaybeeasiertoreversewhiledoorsareoff.)

1. Removetwoscrewsattachinghandletobottomof freezerdoor.

2. Slidehandlestraightdownandpullhandleoffdovetail screwondoor.

3. Removedovetailscrewfromdoorandinstallonother side,movingholeplugsfromcorrespondingholesto

oppositeside.

TO ATTACHFREEZERHANDLE:

1. Placetopofhandleoverdovetailscrew,pullhandle straightupuntilhandleisalignedwithscrewholeson

bottomofdoor.

2. Securebottomofhandlewithtwoscrewsremovedearlier.

over

Dovetail Screw

Loct_Handle

over

Dovetail Screw

TO REVERSE REFRIGERATOR/FREEZER HANDLES: Handles may be easier to reverse while doors are off.

Reverse freezer and refrigerator handles as shown.

Handle Reversal

Ice Maker_

Ice Bucket _

S Freezer Light

Freezer Shelf _

Freezer

Control

Refrigerator

Control

Deli Drawer Cover

Dell Drawer

Half Shelf

Wine Rack

Full

Special Item

Mid Level Li

Crisper

i iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii _

_--Fixed Door Bin

Fixed Door Bin

Door Rack

Dairy Door

Tall Bottle

Retainer

Snugger

Door Bin

Door Rack

Crisper

Drawers

_Toe Grille

Features may vary according to model

COOLDOWNPERIOD

To ensure safe food storage, allow the refrigerator to operate with the doors closed for at least 8 to 12 hours before loading

it with food.

REFRIGERATOR & FREEZER CONTROLS

Freezer Control (some models)

TEMPERATURE ADJUSTMENT

* Adjust temperature gradually: move the knob in small

increments, allowing the temperature to stabilize,

, For colder temperatures, turn the knob towards Colder. , For warmer temperatures, turn the knob towards Cold.

Turning the refrigerator control will change temperatures in both compartments. For example, if the refrigerator control is turned to a colder setting, the freezer control may have to be

adjusted to a warmer setting. Turning the freezer control will change only the freezer temperature.

To maintain temperatures, a fan circulates air in the

refrigerator and freezer compartments. For good circulation,

do not block cold air vents with food items.

cI,o, c;°o,

e e

Refrigerator Control (some models)

TEMPERATURE ADJUSTMENT GUIDE

if Refrigerator compartment is Too Warm Turn Refrigerator Control Slightly Towards Colder.

if Refrigerator compartment is Too Cold Turn Refrigerator Control Slightly Towards Cold.

If Freezer compartment Is Too Warm Turn Freezer Control Slightly Towards Colder.

If Freezer compartment Is Too Cold Turn Freezer Control Slightly Towards Cold.

Refrigerator & Freezer Control (some models)

* To Turn Refrigerator Off Turn Refrigerator Control To O.

SHELF ADJUSTMENT

Refrigerator shelves are easily adjusted to suit individual

needs. Before adjusting the shelves, remove all food. To adjust sliding shelves:

Remove shelf by pulling forward to stop position. Lift front edge up and pull out.

Replace the shelf on any pair of rails by reversing this

procedure.

Sliding Glass Shelf

Sliding Wire Shelf

To adjust cantilever shelves:

DOOR STORAGE

Door bins, shelves, and racks are provided for convenient storage of jars, bottles, and cans. Frequently used items can be quickly selected.

Some models have door racks or bins that can

accommodate gallon-sized plastic drink containers and economy-sized jars and

containers. Some racks are adjustable for maximum

storage capacity. The dairy compartment,

which is warmer than the general food storage section,

is intended for short term storage of cheese, spreads,

or butter.

Door Rack

ADJUSTABLE DOOR BINS

Some models have adjustable door bins that can be moved to suit individual needs.

To move door bins

1. Lift bin straight up.

2. Remove bin.

3. Place bin in desired position.

4. Lower bin onto supports until

locked in place.

Lift front

O edge up. O Pull shelf out.

Replace the shelf by inserting the hooks at rear of the shelf into

the wall bracket. Lower the shelf into the desired slots and lock into position.

SpillProoF Mglass shelves (some models) catch and hold

accidental spills. In some models, the SpillProoff Mshelves slide out for easy access to food and for fast cleaning. The shelves slide out independently of the cantilever brackets. Just pull the front of the shelf forward. The shelf can be extended as

far as the stopper will allow but it is not removable from the cantilever bracket.

Full Width Cantilever

Glass Shelf

Cantilever Glass Shelf

Fixed and Sliding

Adjustable Door Bin

TALL BOTTLE RETAINER (SOME MODELS) The Tall Bottle Retainer keeps tall containers in the bin from

falling forward when opening or closing the refrigerator door.

To install, hold the retainer at the top, and slide it over the outside wall of the bin, as shown in the diagram. The Tall Bottle

Retainer works best with a Bin Snugger.

Tall Bottle Retainer deft_ anG Bin Snugger (right)

FREEZER TiLT OUT DOOR RACK

Freezer Tilt Out Door Rack

CRISPERS (SOME MODELS)

The crispers, located under the bottom refrigerator shelf, are designed for storing fruits, vegetables, and other fresh

produce. Wash items in clear water and remove excess

water before placing them in the crispers. Items with strong odors or high moisture content

should be wrapped before storing.

Crisper Drawer

HUMIDITY CONTROL

(SOME MODELS)

The Humidity Control, present on some models

with crisper drawers, allows you to adjust the humidity within the crisper. This can

extend the life of fresh vegetables that keep best in high humidity.

DELl DRAWER (SOME

MODELS) Some models are equipped

with a Dell Drawer for storage of luncheon meats, spreads,

cheeses, and other dell items.

WINE RACK (SOME MODELS) There are two different style Wine Racks. (See A and B

below.) The Wine Rack stores bottles of wine, or single two- liter plastic bottles ofjuice or soda pop. To install, slide Wine Rack (A) onto the shelf with the curve facing in.To remove,

slide the Wine Rack out. Install on either side of shelf. The Wire Wine Rack (B) simply sets on the shelf.

Wine Racks

Dell Drawer

SPECIAL ITEM RACK (SOME MODELS)

The innovative design of the Special Item Rack allows you to store a six-pack of 12 ounce

drink cans, a bottle of wine, a two-liter soft drink bottle, or a carton of eggs. The Special

Item Rack mounts on the left side of your refrigerator. To

install, just slide the Special Item Rack onto any shelf as

shown in the drawing. Special Item Rack

FOOD STORAGE iDEAS

Fresh Food Storage

. The fresh food compartment should be kept between 34°F

and 40° F with an optimum temperature of 37° R

. Avoid overcrowding the refrigerator shelves. This reduces

the circulation of air around the food and results in uneven cooling.

Fruits and Vegetables

. Storage in the crisper drawers traps moisture to help

preserve the fruit and vegetable quality for longer time periods.

Meat

,, Raw meat and poultry should be wrapped securely so

leakage and contamination of other foods or surfaces

does not occur.

Frozen Food Storage

,, The freezer compartment should be kept at 0° F or lower. ,, A freezer operates most efficiently when it is at least 2/3

full.

Packaging Foods for Freezing

,, To minimize dehydration and quality deterioration, use

aluminum foil, freezer wrap, freezer bags or airtight containers. Force as much air out of the packages as

possible and seal them tightly. Trapped air can cause food

to dry out, change color, and develop an off-flavor (freezer

burn).

,, Wrap fresh meats and poultry with suitable freezer wrap

prior to freezing.

,, Do not refreeze meat that has completely thawed.

Loading the Freezer

,, Avoid adding too much warm food to the freezer at one

time. This overloads the freezer, slows the rate of freezing, and can raise the temperature of frozen foods.

,, Leave a space between the packages, so cold air can

circulate freely, allowing food to freeze as quickly as

possible.

,, Avoid storing hard-to-freeze foods such as ice cream and

orange juice on the freezer door shelves. These foods are

best stored in the freezer interior where the temperature

varies less.

ENERGY SAVING iDEAS

,, Locate the refrigerator in the coolest

part of the room, out of direct sunlight, and away from heating

ducts or registers. Do not place the refrigerator next to heat-producing appliances such as a range, oven, or dishwasher. If this is not possible,

a section of cabinetry or an added layer of insulation between the two appliances will help the refrigerator operate more efficiently.

,, Level the refrigerator so that the doors close tightly. ,, Refer to this Use & Care Manual for the suggested

temperature control settings.

,, Periodic cleaning of the condenser will help the

refrigerator run more efficiently. See the Care and

Cleaning Chart.

,, Do not overcrowd the refrigerator or block cold air vents.

Doing so causes the refrigerator to run longer and use

more energy.

,, Cover foods and wipe containers dry before placing them

in the refrigerator. This cuts down on moisture build-up inside the unit.

,, Organize the refrigerator to reduce door openings.

Remove as many items as needed at one time and close

the door as soon as possible.

If your refrigerator has an automatic ice maker, it will provide a

sufficient supply of ice for normal use. During the initial startup of your refrigerator, no ice will be produced during the first 24

hours of operation. Air in new plumbing lines may cause the ice maker to cycle two or three times before making a full tray of ice. With no usage, it will take approximately one to two days

to fill the ice container.

New plumbing connections may cause the first production of

ice cubes to be discolored or have an odd flavor. Discard ice made during the first 24 hours.

TURNINGYOUR ICE MAKER ON

After the plumbing connections have been completed, the water supply valve must be opened. Place the ice container

under the ice maker, pushing it as far back as possible. Lower

the wire signal arm to its "down" or ON position. TURNINGYOUR iCE MAKER OFF

To stop the ice maker, lift the wire signal arm until it clicks and locks in the "up" or OFF position.

The ice maker also turns off automatically when the ice

container is full. If your model has an adjustable freezer shelf, place the shelf in the lower position, so that the wire signal

arm will hit the ice when the container is full.

Wire y

Signal Arm

iCE MAKER TiPS

,, Ice cubes stored too long may develop an odd flavor.

Empty the ice container and ensure that the wire signal arm is in its "down" or ON position. The ice maker will then produce more ice.

,, Occasionally shake the ice container to keep ice

separated.

,, Stop the ice maker when cleaning the freezer and during

vacations.

,, If the ice maker will be turned off for a long period of time,

turn the water supply valve to a closed position.

_, Wash the ice container in warm water with mild detergent.

Rinse well and dry.

• Stop the ice maker when cleaning the freezer and during vacations.

,, If the ice maker will be turned off for a long period of time,

turn the water supply valve to the closed position.

iCE PRODUCTION: WHATTO EXPECT

The ice maker will produce 2.5 to 3 pounds of ice every 24 hours depending on usage conditions. Ice is produced at a rate of 8 cubes every 80 to 160 minutes.

UNDERSTANDINGTHE SOUNDSYOU MAY HEAR

Your new high-efficiency refrigerator may make unfamiliar sounds. These are all normal sounds and soon will become

familiar to you. They also indicate your refrigerator is operating as designed. Hard surfaces, such as vinyl or wood floors, walls, and kitchen cabinets may make sounds more noticeable. Listed below are descriptions of some of the most

common sounds you may hear, and what is causing them.

A. Evaporator

The flow of refrigerant through the evaporator may create a boiling or gurgling sound.

B. Evaporator Fan

You may hear air being forced through the refrigerator by the evaporator fan.

C. Defrost Neater

During defrost cycles, water dripping onto the defrost heater may cause a hissing or sizzling sound. After

defrosting, a popping sound may occur.

D. Automatic lce Maker

If your refrigerator is equipped with an automatic ice maker, you will hear ice cubes falling into the ice bin.

E. Cold Control & Defrost Timer or Automatic

Defrost Control

These parts can produce a snapping or clicking sound when turning the refrigerator on and off. The timer also

produces sounds similar to an electric clock.

F. Condenser Fan

if condenser coils are located underneath your refrigerator as shown in the drawing at the left, you have a condenser fan. You may hear air being forced

through the condenser by the condenser fan.

G. Compressor

Modern, high-efficiency compressors operate much

faster than older models. The compressor may have a

high-pitched hum or pulsating sound.

N. WaterValve

If your refrigerator is equipped with an automatic ice maker, you will hear a buzzing sound as the water valve

opens to fill the ice maker during each cycle.

L Drain Pan (Nonremovable)

You may hear water running into the drain pan during the defrost cycle. The drain pan will be located on top

of the compressor for air-cooled condensers (black coils on back of refrigerator).

J. Condenser Coils (Fan-cooled models only)

Keep your refrigerator and freezer clean to prevent odor build-up. Wipe up any spills immediately and clean both sections at least twice a year. Never use any type of scouring pads, brushes, abrasive cleaners or strong alkaline solutions on any surface. Do not wash any removable parts in a dishwasher. Always unplug the electrical power cord from the wall outlet before cleaning.

Care & Cleaning Chart

Part What To Use Tips and Precautions

Interior/Door • Soap and water Use 2 tablespoons of baking soda in 1 quart of warm water. Be sure to wring

Liner • Baking soda and water excess water out of sponge or cloth before cleaning around controls, light

Door Gaskets • Soap and water Wipe gaskets with a clean soft cloth. Drawers/Bins • Soap and water Do not wash any removable items (bins, drawers, etc.) in dishwasher. Glass Shelves • Soap and water Allow glass to warm to room temperature before immersing in warm water.

Toe Grille • Soap and water Vacuum dust from front of toe grille. Remove toe grille Vacuum backside and wipe

Exterior and • Soap and water Do not use commercial household cleaners, ammonia, or alcohol to clean handles. Handles

Exterior and Handles

(Stainless Steel Models Only)

Condenser Coils • Condenser Cleaning Brush is No need to clean unless operating refrigerator under particularly dusty or greasy (Fan-cooled available from your dealer, conditions, or if there is significant pet traffic in your home. If cleaning is necessary, models only) • Vacuum Cleaner remove toe grille and use extended vacuum attachment and condenser cleaning

Condenser Coils • Vacuum Cleaner Use the dusting tool attachment on your vacuum to remove dust build-up on the (Air-cooled models condenser coils (black tubes and wires) attached to the back of air-cooled only) refrigerators only.

Defrost Water Pan • Soap and water Some models have defrost water pan located on top of compressor at bottom rear

Exterior (Easy Care

Stainless Steel Models)

• Glass cleaner

• Mild liquid sprays

• Mild liquid sprays with sudsy cloth or sponge. Rinse and dry.

• Vacuum attachment

• Soap and water

• Ammonia

• Stainless Steel Cleaners

• Soap and water

• Mild liquid sprays

bulb or any electrical part.

Clean stainless steel front and handles with non-abrasive soapy water and a dishcloth. Rinse with clean water and a soft cloth. Wipe stubborn spots with an ammonia-soaked paper towel, and rinse. Use a non-abrasive stainless steel cleaner. These cleaners can be purchased at most home improvement or major

department stores. Always follow manufacturer's instructions. NOTE: Always clean, wipe and dry with the grain to prevent cross-grain scratching.

Wash the rest of the cabinet with warm water and mild liquid detergent. Rinse well, and wipe dry with a clean soft cloth.

brush to remove dust build-up from condenser coils (see item "J'+in "NORNAL OPERATING SOUNDS & SIGHTS'+).

of refrigerator (see illustration on next page). Wipe water pan with damp cloth. NOTE: The defrost water pan is NOT removable.

Use warm soapy water to clean Easy Care surfaces. Mild liquid sprays may be used on stubborn spots.

+ 39 hidden pages