Kenmore 25359682995, 2535808789B, 2535808289B, 25350682002 Owner’s Manual

Owners Guide

Side by Side
Ice and Water

Refrigerator

CAUTION:
Before using this refrigerator, read this

manual and follow all its Safety Rules
and Operating Instructions.

Sears, Roebuck and Co., Hoffman Estates, IL 60179

Visit our Sears website: www_searsocom
Printed in the USA

It

Safety
Installation

Operation
Maintenance

Troubleshooting

Espa_ol
Fran(_ais

218955301 (0006)

Record Serial/Model Numbers .............. 2

Safety ....................................................... 2-3

Warranty .............................................. 3

Canada - Limited Warranty .................. 4

First Steps ................................................. 5-6

Energy Saving Tips ................................ 7

Setting the Controls ................................ 7

Fresh Food Storage ............................. 7-8

Automatic Ice and Water Dispenser .....9-11

Touch Pad .............................................. 9

Ice and Water Filter .......................... 11

Care and Cleaning ................................ 12-t3

Removing the Handles and Doors ........13-14

Avoid Service Checklist ......................... 15-18

Normal Operating Sounds ...................... 19

Sears Service ........................................ 20

Sears Canada Customers ..................... 20

READ AND SAVETHESEINSTRUCTIONS

This Owner's Guide provides specific operating instructions
for your model. Use your refrigerator only as instructed in

this guide. These instructions are not meant to cover every
possible condition and situation that may occur_ Common

sense and caution must be practiced when installing,
operating, and maintaining any appliance,

Record Your Model and Serial Numbers

Record the model and serial numbers in the space provided

below, The serial plate is located on the ceiling of the
refrigerator compartment.

Model Number: 253.

or 970.

Serial Number:

Purchase Date:

READ ALL INSTRUCTIONS BEFORE USING
THIS REFRIGERATOR.

FOR YOUR SAFETY

Do not store or use gasoline, or other flammable vapors and
liquids in the vicinity of this or any other appliance Read

product labels for flammability and other warningsv

CHILD SAFETY

• Destroy carton, plastic bags, and any exterior wrapping
material immediately after refrigerator is unpacked.
Children should never use these items to play Cartons

covered with rugs, bedspreads, plastic sheets or

stretch wrap may become airtight chambers, and can
quickly cause suffocation.

• Remove all staples from the carton.. Staples can cause

severe cuts, and destroy finishes if they come in
contact with other appliances or furniture.

• An empty, discarded ice box, refrigerator, or freezeris a
very dangerous attraction to children.

Remove the door(s) of any appliance that is not in use,

even if it is being discarded,

Proper Disposal of Your

Refrigerator/Freezer

Risk of child

entrapment, Child entrapment and
suffocation are not problems of the
past, Junked or abandoned
refrigerators or freezers are still

dangerous -- even if they will sit for
"just a few days." tf you are getting

rid of your old refrigerator or freezer,
please follow the instructions below
to help prevent accidents,

BEFORE YOU
THROW AWAY
YOUR OLD
REFRIGERATOR/
FREEZER:

• Remove
door&

• Leave

shelves in

place so

children may

not easily

climb inside°

2

ELECTRICAL INFORMATION

These guidelines must be followed to ensure that
safety mechanisms in the design of this refrigerator

will operate properly.

• Refrigerator must be plugged into its own 115 Volt,

60 Hz°,AC only electric outlet. The power cordofthe

appliance isequipped with a three-prong grounding
plug for your protection against shock hazards. It must

be plugged directly into a properly grounded three-

prong receptacle_ The receptacle must be installed in
accordance with local codes and ordinances. Consult a

qualified electrician. Do not use an extension cord or
adapter plug.

o If voltage varies by 10% or more, performance of your

refrigerator may be affected. Operating refrigerator with
insufficient power can damage the compressor.

- To prevent the refrigerator from being turned off
accidentically, do not plug unit into an outlet controlled
by a walt switch or pull cord°

o Do not pinch, knot, or bend the cord in any manner..
OTHER PRECAUTIONS

FULL ONE-YEAR WARRANTY ON

REFRIGERATOR

For one year from the date of purchase, when this
refrigerator is operated and maintained according to the

instructions provided in this Owner's Guide, Sears will
repair this refrigerator, free of charge, if defective in

material or workmanship

FULL FIVE-YEAR WARRANTY ON SEALED

REFRIGERATION SYSTEM
For five years from the date of purchase, when this

refrigerator is operated and maintained according to the
instructions provided in this Owner's Guide, Sears will

repair the sealed system (consisting of refrigerant,
connecting tube, and compressor motor), free of charge, if
defective in material or workmanship..

The above refrigerator warranty applies only to
refrigerators which are used for storage of food for private

household purposes..

o Never unplug the refrigerator by pulling on the cord.

Always grip the plug firmly, and pull straight out from
the receptacle.

= To avoid electrical shock, unplug the refrigerator before

cleaning and before replacing a light bulb

NOTE: Turning the temperature control to OFF turns off the
compressor, but does not disconnect the power to the light

bulb or other electrical components.

°

Do not operate refrigerator in the presence of explosive

fumes.

m

Avoid contact with any moving parts of automatic ice
maker.

Avoid fire hazard or

electric shock. Do not use an
extension cord or an adapter plug.

Do not remove any prong from the

power cord..

Groundingtype

walt receptacle

FULL 30*DAY WARRANTY ON KENMORE REFRIGERA-

TOR WATER FILTRATION CARTRIDGE° If this Kenmore

Refrigerator Water Filtration Cartridge fails due to a defect

in material or workmanship within 30 days from the date of
purchase, RETURN IT TO THE NEAREST SEARS STORE

IN THE UNITED STATES and Sears will replace it, free of
charge

This warranty gives you specific legal rights and you may
also have other rights which vary from state to state.

Warranty service is available by contacting the NEAREST
SEARS SERVICE CENTER/DEPARTMENT in the United

States, See the back page of this manual,
For warranty questions, please contact the following

address:

Sears, Roebuck and Coo
Dept, 817WA

Hoffman Estates, IL 60179

clrcunlstances_
cut, remove,

or bypass the
grounding prong.

Power supply
cord with 3-prong
grounding plug

CANADA--- LIMITED WARRANTY

Refrigerators

Sears Canada Inc., warrants every new Kenmore refrigerator to be free from defects in material or workmanship. What
Sears will do, free of charge, in case of defect:

The Compressor

The Sealed System

(consisting of refrigerant,

evaporator,and condenser)

,,,,,, ....

AIt other parts or

adjustments

TEN (10) YEARS

FtVE (5) YEARS

ONE (1) YEAR ONE (1) YEAR ONE (1) YEAR

TEN (t0) YEARS

FIVE (5) YEARS

FIVE (5) YEARS

FIVE (5) YEARS

Normal Responsibility of the Customer

The following items, since they are not manufacturing defects, are not included in the warranty, but are the responsibil-

ity of the customer:

t) Damage to finish after' delivery°

2) Improper power supply, low voltage, or any defects in the house wiring system or appliance not connected
to electric outlet..

3) Replacement of light bulbs.

4) Damage caused by moving the product from its original installation_

5) Service required as a result of alteration, abuse, fire, floods, or acts of God.

6) Providing adequate air circulation to the refrigerating system..

7) Proper use and care of product as listed in the customer's manual; proper setting of the controls.

If any service is required under this warranty, simply calf 1-877-LE-FOYER s_(t-877-533-6937)o

This warranty is inaddition to any statutory warranty. The above warranty covers Kenmore Refrigerators sold and operated

in Canada only and shall not apply if the refrigerator is used for other than domestic purposes.

Sears Maintenance Agreement

Maintain the value of your Kenmore refrigerator with a Sears Maintenance AgreemenL

SEARS CANADA INC. • Toronto, Canada • M5B 2B8

PRINTED IN USA.

4

This Owner's Guide provides specific operating instructions
for your model, Use the refrigerator only as instructed in
this Owner's Guide, Before starting the refrigerator,

follow these important first steps.

LOCATION

• Choose a place that is near a grounded electrical
outlet, Do Not use an extension cord or an adapter
plug,

. If possible, place the refrigerator out of direct sunlight

and away from the range, dishwasher or other heat
sources,

• The refrigerator must be installed on a floor that is
level and strong enough to support a fully loaded
refrigerator

o Consider water supply availability for models equipped

with an automatic ice maker

INSTALLATION

• Do not install the refrigerator where temperature will
drop below 60"F (t5°C) or rise above 110°F (43°C).,
The compressor will not be abfe to maintain proper
temperatures

• In a recessed installation, allow an extra 1/2 inch
(10-15 mm) on each side, for ease of installation

• To permit proper door swing, if the hinge side of the unit

will be placed against a wall, allow a 1- 3/4 inch

(44 ram) space between the wall and the refrigerator,

DOOR OPENING
For best use of drawers and freezer basket, refrigerator

should be in a position where both refrigerator and freezer
doors can be opened about 135%

LEVELING

• Refrigerator must be leveled with ali bottom corners

resting firmly on a solid floor. Adjust front rollers to
level cabinet both front-to-rear and side-to-side. Keep

cabinet as low as possibie for stability. Never adjust
cabinet rollers so front is lower than rear.

• To adjust front rollers: Open refrigerator and freezer
doors. Remove toe grille by pulling it straight out.

Adjust rollers by turning each roller adjusting bolt with
an adjustable wrench, a socket wrench, or a nutdriver
until the refrigerator is level and stable.. Rear rollers
are not adjustable..

• Check both doors to ensure the seals touch the

cabinet evenly on all four corners.

* If freezer door is higher than refrigerator door,

raise right corner and/or lower left corner until doors

align across top of cabinet..

• If refrigerator door is higher than freezer door,
raise left corner and/or lower right corner untii doors

align across top of cabinet.

Roller Adjusting Bolt

Adjusting Front Rotlers

Replacing Toe Grille

° To replace toe grille: Line up tabs with holes, and

push grille straight on_

CLEANING

• Wash the inside, alt removable parts, and theoutside
with mild detergent and warm water Wipe dry° Do Not

use harsh cleaners on these surfaces.

• Do not use razor blades or other sharp instruments
that can scratch appliance surface, when removing

adhe sive labels.r Any glue left from tape or energy label
can be removed with a mixture of warm water and mild

detergent, or touch residue with sticky side of tape
already removed.

o Do not remove the Serial Plate,

CONNECTING ICE MAKER TO WATER SUPPLY

Do Not Install Ice Maker Tubing Where

Temperature May Fall Below Freezing,

4_ Secure copper tubing with STEEL CLAMP and screw to

rear panel at location shown (Figure 3).

5oCoil water supply tubing as shown (Figure 3).

Check to be sure your water connection will comply with
local plumbing codes°

Water quality determines your ice quality, tt is best to
connect the ice maker to water' that is not softened.. Chemi-

cats from a malfunctioning softener can damage the ice
maker:. Ifthe ice maker is connected to soft water, ensure

that the softener is maintained and working properly
The ice maker requires a 1/4 inch (6.4 mm) copper water

supply line (with shut off) from your' household water sys-
tem. Allow enough tubing behind your refrigerator to permit
moving out to clean floor.

Water line kit 5308950117 is available through your Dealer at
extra charge. This kit includes 25 ft (7°6 meters) of 1/4 inch
diameter copper tubing plus parts to connect to your cold
water line including a saddle valve assembly You will need
to purchase a 1/4 inch brass compression nut and ferrule
from your local hardware or plumbing store..

1..Turn ON water supply and flush out copper tubing. Turn
OFF water' supply.

2. Unplu!l refrigerator_

NOTE: Toprevent vibration noise and wear, leave aspace
between all tubing and other surfaces.

6 Turn on water supply and check all connections for leaks

(Figure 3).

o
o

0
o
o

Figure 3

7. Plug refrigerator cord into wall outleL

8. To begin ice production, lower the Wire Signal Arm to the
"down" or' "ON" position. (Figure 4)

Figure 1

3_Install WATER SUPPLY LINE as follows (Figure 2):

•SIide brass nut, then ferrule, onto copper tubing

• Push end of copper tubing as far into the metal water
valve fitting as it will go (1/4 inch). Slide ferrule into

fitting and thread brass nut onto inlet, tighten finger tight
plus one-half turn with wrench..

NOTE: Some models may have a cap on the valve_

Unscrew the cap and discard°

Copper water linefrom

household water supply

Brass nut--I_ ......

--!

'ii

Ferrule--_

Figure 4 wire

Ice Maker

Signal Arm

IMPORTANT

Ice production will begin when freezer reaches normal

operating temperaturer Air in new plumbing lines may cause

ice maker to cycle two or three times before making a full

tray of ice_

New plumbing may cause ice to be discolored or have poor
flavor_ Discard ice made during the first 24 hours. After

installation, if you wish to shut the ice maker off, Iiftshutoff
arm until it clicks and locks in UP position_

Figure 2

Install the refrigerator in the coolesl

part of the room, out of direct sunlight
and away from heating ducts or

registers, Do not place the

refrigerator next to heat-producing
appliances such as a range, oven
or dish washer, Ifthis is not possible, a

section of cabinetry or an added layer of
insulation between the two appliances will help the

refrigerator operate more efficiently,

o

Level the refrigerator so the doors close tightly.
Refer to this Owner's Guide for the suggested

refrigerator settings,
Periodic cleaning of the condenser will help the

refrigerator run more efficiently, See "Outside" in the
Care and Cleaning section.

Do not overcrowd the refrigerator or block cold air

vents. Doing so causes the refrigerator to run longer

and use more energy Shelves should not be lined with
aluminum foil, wax paper or paper toweling, Liners
interfere with cold air circulation, making the refrigerator
less efficient, which could cause food spoilage,

Cover foods and wipe containers dry before placing
them in the refrigerator,, This cuts down on moisture
build-up inside the unit.
Organize the refrigerator to reduce door openings,
Remove as many items as needed at one time and

close the door as soon as possible.

Turning the freezer control may change temperatures in
both compartments. For example, _fthe freezer control is
turned to a colder setting, the refrigerator control may have
to be adjusted to awarmer one. Turning the refrigerator

control will change only the refrigerator temperature_

IMPORTANT: If the freezer control is turned to OFF,
cooling stops in both compartments.

You may hear the "Frost Free" system working., Afan

circulates air in the refrigerator and freezer compartments,

For good circulation and maintenance of proper cooling
temperatures, do not block cold air vents with food items_
Water draining into the defrost water pan and hissing

sounds are normal during the automatic "Frost Free" cycle,

COLDEST

I COLD

REFRIGERATOR

Refrigerator Midpoint (some models)

COOt. DOWN PERIOD
To ensure safe food storage, allow the refrigerator to

operate with the doors closed fora feast 8 to !2 hours
before loading with food.,

REFRIGERATOR CONTROL

The refrigerator controf should be set at the midpoint of
the dial for a trial period of 24 hours_

After 24 hours, adjust the control as needed. For colder
temperatures, turn the dial a notch towards COLDEST.

For warmer temperatures,turn the dial a notch toward
COLD, Adjust temperature by one increment at a time,

FREEZER CONTROL

The freezer control should be set at the midpoint of the
dial for a trial period of 24 hours_

o

After 24 hours, adjust the control as needed, For colder
temperatures, turn the dial a notch towards COLDEST,

For warmer temperatures, turn the dial a notch towards
COLD° Adjust temperatures by one increment at atime.

NOTE: When first setting the controls or when changing a
setting, wait 24 hours for the temperature to stabilize before

making additional changes

SHELF ADJUSTMENT

Refrigerator shelves are easily adjusted
to suit individual needs. Before adjusting
shelves, remove all food. The shipping

clips that stabilize the shelves for
shipping may be removed and discarded.,

Spillproof TM glass shelves catch and

hold accidental spills,, in some models,
the Spillproof TM shelves slide out for

easy access to food and fast cleaning.
The shelves slide out independently of

the cantilever bracket, Just pull front of
shelf forward Shelf can be extended as

RemoveShipping

Clips

far as stopper wil_allow and is not

removable from the cantilever bracket,,

To adjust the cantilever shelves (shelves supported at the
rear of the refrigerator), lift the back of the shelf up and out.

Replace shelf by inserting hooks at rear into slots, Lower
and lock into position.

Cantilever Shelf

FREEZER BASKET

A slide-out wire basket (some models have two) hangs

below the bottom freezer shelf. This basket provides easy

access to frozen food packages.
TALL STORAGE COMPARTMENT (SOME MODELS)

A sheff is attached to
the freezer wall just

below the ice sewer.

This allows for conve-

nient storage of tall
items placed verti-
cally between the ice

server andthefreezer
wall,

Tall

Storage

Compartment

DOORSTORAGE

Door bins and shelves are provided for convenient storage

of jars. bottles and cans, Items used often are available for
quick selection,

The door bins can be moved to suit individual needs

Remove bins by lifting straight up,. Place bins in the desired

position and lower over' the supports,
The Dairy compartment is warmer than the general food

storage section and is intended for short term storage of
cheese, spreads, or butter:.

CRISPER

The Crisper drawer, located under the bottom refrigerator
shelf, is for storing fruits and vegetables. Most produce

should be washed in clear water and drained before
placing in this drawer° Items with strong odors or high

moisture should be wrapped before storing..

MEAT KEEPER

The Meat Keeper is located at the bottom of the refrigerator:
The temperature inthis compartment can be made colder

than the rest of the refrigerator compartment by sliding the
Chilled Air Controi knob within

the COLDEST or COLD range.

Meat will be partially frozen and
may be kept fresh longer than if
stored on a refrigerator shelf°

MICRO-SERVE
DISHES (SOME

MODELS)

Food can be stored, cooked*, and served in Micro-Serve
Dishes provided in some models. These dishes slide easily

into their own tray, which hangs below a door gallon bin as

shown below, conveniently freeing shelf space for other

item& NOTE: Do not hang tray below the bin infront of the
ice makerr

* Remove plastic lid before cooking Lid is intended for storage only

Snugger

Micro-Serve Dish Tray

Micro-Serve Dishes

Before placing items in the
Meat Keeper, follow these

steps to keep the meat fresh:

• Carefully handle meat with clean hands and always
keep the compartment clean°

= Store meat in itsodginal wrappeL If necessary, wrap in

plastic wrap or'foil to prevent drying. Wrap fish tightly
to prevent odor transfer to other foods.

• If spoilage ever occurs, disinfect the compartment with
liquid chlorine bleach following label directions. Then

rinse with a solution of baking soda and water. Rinse
with clear water and dry.

WINE RACK (SOME MODELS)
The Wine Rack stores

bottles of wine, or 2qiter
plastic bottles of juice or

soda pop° To install,
slide the wine rack onto

the shelf with the curve
facing inoTo remove,

slide the wine rack out.

Theiceandwaterdispenseronthefreezerdoor
convenientlydispenseschilledwater,andeithericecubes

orcrushedice,dependingonthemodel.Somemodels
featureaslideknobselectorforiceandwaterdispensing,
whileothermodelsfeatureatouchpadselectorfor
dispensing

Tooperatethedispenser,pressthepadorslidetheknobfor
theselectionofyourchoiceandpressaglassagainstthe
dispensingarm.HoldthegIassasfarupaspossibleto
catchallice Tostopdispensing,pullglassawayfrom
dispensingarm.Whendispensingice,releasethe
dispensingarmbeforetheglassisfull,butdonotremove
theglassuntiitheicehascompletelydispensed.
(Completeinstructionsforthedispenseroperationare
attachedtotheinsideofthefreezerdoor.)

Asmallheatedareabeneaththedispenserfloorcatches
andevaporatessmallspills.Thisdriptrayis removable

and dishwasher safe.. Do not pour water or excess
cubes into this area because there is no drain

LIGHT

The dispenser has a fight which can be turned on and off by
sliding the knob to the desired position or by pressing the
"Light ON/OFF" pad..The light afso turns on automatically
when ice and/or water is dispensed. Replace light bulb with
an appliance bulb of the same wattage.

Dispenser Selector

To ensure fresh-tasting water, plan to use the dispenser
every day.. If the water dispenser has not been used for a
week or more, draw and discard 7-8 glasses to freshen the
tank supply..

HOW THE ICE DISPENSER WORKS
The ice maker and ice storage bin are located in the top left

corner of the freezer compartment. After the refrigerator is
installed properly and has cooled for several hours, the ice
makercan begin making ice To begin ice production, lower

the wire signal arm tothe "down" or ON position. As cubes
are made, they are stored in the storage bin. Although it

may take 1 or 2 days to fill the bin, the dispenser may be
used after the first batch of ice is made.. The ice maker

turns off automatically when the ice storage bin is futl.
Because of new plumbing connections, the first production

of ice cubes may be discolored or have an odd flavor.
These should be discarded until the cubes made are free

of discoloration and taste

_Remember, water quality determines yourice

quatity It isbest to connect the ice maker to water that is
not softened.. Chemicals from a malfunctioning softener

can damage the ice maker.. If ice maker is connected to
soft water, ensure the softener is maintained and working

properly.

Press glass against dispensing arm

Slide Knob

HOW THE WATER DISPENSER WORKS
Thewatertank is located behindthe drawers intherefrigerator

compartment.. As the water isdispensed, the tank is
automatically refilled.For proper operation ofthe dispenser,the
supply water pressure must fall between 30 psi and 120 psi.

After the refrigerator is installed and the plumbing
connections are complete, the water tank should be filled

by drawing one glass of water. This will take about 1-1/2
minutes. Then, draw and discard 7 more glasses to be sure

that the tank and plumbing connections are rinsed of any
impurities° The water delivery system has a built in shut off

device that wilt stop the water flow after 3 minutes of
continuous use. Simply release the actuator button to reset

the dispensing mechanism.

Touch Pad

Slide Knob Touch Pad

To stop the ice maker, lift the wire signal arm until it clicks
and locks in the "up" or OFF position_

Wire

Signal Arm

Ice Maker

LOCKOUT FEATURE (TOUCH PAD MODELS)

Your ice and water dispensing system can be locked out to

rrevent unwanted use,, To do this, press the picture of the

for 3-5 seconds. When the system is locked off, a

;mall red light will appear over' the padlock. To unlock the

press the padlock for' 3-5 seconds until the small

red light goes out° Your ice and water dispenser is now

ready to use again.

CE DISPENSER TIPS

tce cubes stored too long may develop an odd flavor:
Empty the container and return it to the proper position.

The _ceMaker will then produce more ice.

2, Occasionally shake the container to keep ice separated.

3 If the dispensing arm is pushed in for more than 4

minutes, the dispenser motor' may overload and stop,
The overload protector win reset automatically after 3 or
4 minutes,, if a large quantity of ice is needed at one
time, it is best to remove cubes directly from the ice
storage bin.

4. Certain sounds are normal when the Ice Maker is
operating_ They are:

• Motor operation

- Ice being loosened from the tray

• ice dropping from the storage bin

o Running water
. Water valve opening or closing

For more information on these operations, see Normal

Operating Sounds.

5. Stop the Ice Maker when cleaning the freezer or for long
vacations_

6 If the Ice Maker is to be turned off for a !ongperiod of

time, turn the water supply valve to the closed position.

CLEANING THE ICE DISPENSER

Clean the dispenser' and ice storage bin at regular intervals,
particulmty before you take a vacation or move, or if the ice
Dispenser sticks,,

1. Stop ice production by lifting the wire signal arm to the
"up" or OFF position.

2. Remove ice storage bin by lifting up and out. Empty and
carefully clean the bin with mild detergent. Do not
submerge the bin while cleaning, Rinse with clear water:

Do not use harse or abrasive cleaners. Allow ice bin to

dry completely before replacing in the freezer.

3_ Remove ice chips and clean the shelf and chute that

supports the ice storage bin.

4o Replace the ice storage bin,,Lower the wire signal arm

on the Ice Maker to the "down" position or ON position
and the Ice Maker will resume production,

IMPORTANT: When removing or' replacing the icebin, do
not rotate the auger in the ice bin,. tf the auger is

accidentialty turned, you must realign the auger by turning

itin 90 ° turns until the ice bin fits into place with the drive
mechanism,, For further instruction, see the label on the ice

bucket.

Remove and empty the ice storage bin if:
1_An extended power' failure (one hour or longer) causes

ice cubes in the ice storage bin to melt and freeze

together and jam the dispenser mechanism,

2_The ice dispenser is not used frequently. Ice cubes will

freeze together in the ice storage bin and jam the

dispenser mechanism Remove the ice storage bin and
shake to loosen the cubes_

NEVER use an ice pick or' sirniliar sharp instrument to
break up the ice,.This could damage the ice storage bin

and dispensel mechanism

Do not use the ice

chute as a handle when removing or
replacing the ice storage bin.

Surfaces there may be sharp.

Do Hotpu_FIngera UpIce C_.u_e,
Su_ceaThere May Be Sharp!

10

NOTE:IfyoupurchasedarefrigeratorwithaKenmoreIce

andWaterFilter,pleasereadthefollowinguseandcare

information,,

Thisiceandwaterfiltersystemfilterswatertoyourice

makerandwaterdispenser..Itislocatedintheupperright
backcornerofthefreshfoodcompartment(SeeFigure1)_

SYSTEMSTARTUP:

Water supply does not need to be turned off, however do

not use ice and water dispenser while installing filter
Refer to Figure 1 as you complete these instructions.

The filter cartridge has already been installed in the filter

housing at the factory. Refer to the "How The ice Dispenser

Works" section to properly fill the system with water
CHANGING THE FILTER:

Water quality varies throughout the world. To ensure the
highest possible water quality, change water filter every 6

months, or 200 gallons. Also, if filter has been in a
refrigerator that has not been in use for awhile (during

moving for example), change filter before reinstalling
refrigerator. Note dispenser system will atso operate

without filtration (with filter cartridge removed).

10..Check for leaks. Open refrigerator door, Wipe any
water drops from the filter cup. Run a glass of water, tf

there is a leak, unscrew filter cup, and reinsert the filter
cartridge.. Check placement of large Q-ring (see
Figure1). Reinstall filter cup, making certain it is

tightened completely.

11.To condition filter system and purge air from water line
run several glasses of water through water dispenser.
This will also assure that the purest water

possible is stored in water tank.

FILTER INDICATOR RESET

The "Change Filter" indicator light will light up each time the
dispenser is used While the filter is still operating within its

specified Iife cycle, the filter indicator light will be green. When
the filter has reached approximately 80% of its useful fife,the
green light will become anamber light. This isthe

recommended time to purchase a replacement filter cartridge.
When the filter is 100% used up, the amber Iight will become
a red light. You should change the filter as soon as possible at
this time. After the filter cartridge has been changed, press
the words that say "Filter Light Reset'L If the light was redor
amber, you wilt need to press for 3-5 seconds to reset to
green (the green light will flash when reset is complete)If the
light was still green, you will need to press for 10-t2 seconds
to reset (again the green light will flash when reset is
complete.

TO CHANGE FILTER:
Refer to Figure 1 as neede& It is not necessary to turn

the water supply off to change the filter.

1. Set ice maker lever (wire signal arm) to the OFF (up)
position

2. Hold filter cup firmly, and unscrew counter clockwise
(Figure 1). (Some water could leak out as you remove
cup. This is normal..) Filter cartridge should come
downwith cup If cartridge remains in housing, pull

downgentty, while twisting filter back and forth.

3 Empty cup of any substance.

4. The large o-ring (Figure 1) that seals the filter system
sets in the o-ring groove down inside the cup. Should

the o-ring fall out during filter cartridge replacement,

simply place it back in the groove prior to screwing the

cup back in place If the o-ring becomes damaged, you
will need to order one from the Consumer Assistance

Center.

5 Discard old filter cartridge.

6. Remove new filter cartridge from packaging, and
install

7 Place filter cartridge in cup. The end with the small

o-ring should be up, out of the cup.

& Screw cup, with filter, back onto housing.. Filter

cartridge will self-align as cup is tightened Be sure cup
is completely tightened with Kenmore logo facing

outward. Do not tighten past stop,.

9. Set ice maker lever on the ON (down) position.

Figure 1

New filter cartridges can be obtained through your local Sears Retail
Store, or contact the Sears Service Center at:

1-800-366-7278 (UoS,A,,& Canada)
It might be good to order some filters when you first install your

refrigerator, Be sure to ask for the RC-200 Kenmore replacement
cartridge,, (Replacement Part Number 9066).

The Kenmore RF-200 ice and water filter system is tested and

certified by NSF International, the nationally recognized and
respected, not for profit, certification organization for public health
safety. The Kenmore Filter system is tested and certified to ANSI/NSF

Standards 42 and 53. See performance data sheet for specifications.
This system should not be used on water that is microbiologically

unsafe or with water of unknown quality unless the water has been

adequately disinfected before crafter traveling through the filtration

Rated service flow- .37 GPM
Maximum Rated Pressure- 125 PSI

system_
Maximum Operating Temp. - 100 °

11

Keep your refrigerator and freezer clean to prevent odor
build-up.. Wipe up any spills immediately and clean both
sections at least twice a year. Never use metallic

scouring pads, brushes, abrasive cleaners or strong
alkaline solutions on any surface. Do not wash any
removable parts in a dishwasher

Always unplug the power cord from the wa# outlet

before cleaning,

NOTE: Turning the control to OFF does not disconnect power

to the controls, light bulb, or other' electrical components.

metal surfaces. Do not touch refrigerated
surfaces with wet or damp hands.

INSIDE

Wash inside surfaces of the refrigerator and freezer with a
solution of 2 tablespoons baking soda in 1 quart warm

wate_. Rinse and dry thoroughly, Be sure to wring excess

water out of sponge or cloth before cleaning around the
controls, light bulb, or any electrical parts.

Wash removable parts such as shelves and drawers with
baking soda solution or mild detergent and warm water. Do

not use harsh cleaners on these surfaces. Rinse and
dry thoroughly. Clean the door gaskets with mild suds,

rinse with clear water and wipe dry.
Do not use razor blades or other sharp instruments which

can scratch the appliance surface when removing adhesive
labels. Any glue left from the tape or energy label can be
removed with a mixture of warm water and mild detergent,
or, touch the glue with the sticky side of tape already
removed. Do Not remove the serial plate.

OUTSIDE
Wash the cabinet and handles with warm water and mild

liquid detergent.. Rinse well and wipe dry with a clean soft
cloth. Do not use commercial household cleaners,

ammonia, or alcohol to clean handles..

Clean stainless steel (some models) front and handles
with hot soapy water and a dishcloth. Rinse with clean
water and a soft cloth,. Wipe stubborn spots with an

ammonia-soaked paper towel, and rinse. Cleaners made
especially for stainless steel, such as Sheila Shine,

trademark of Sheila Shine, Inc., Stainless Steel Magic,
trademark of Magic American Corp., or' similar products
are suggested_ Always follow manufacturer's instructions..

Wash the rest of the cabinet with warm water and mild liquid
detergent. Rinse well, and wipe dry with a clean soft cloth°

Remove any dust or dirt from the front of the toe grille using
a vacuum cleaner with its dusting toot attachment_ Remove
the toe grille by pulling it straight ouL While the grille is
removed, vacuum the backside of the grille and wipe with a

sudsy cloth or sponge°

Damp objects stick to cold

rl_[,_-'_==l{,]o!To avoid damage and help
the refrigerator run as efficiently as

possible, clean the condenser and air
vents periodically.

Per'iodicalty clean the condenser (black tubes and wires
beneath the refrigerator, behind the toe gritle). Do not allow

lint or dust to accumulate on the coils. Insert a long handled
brush or vacuum attachment between the two coils to bring

the lint forward. To replace the toe grille, line up tabs with
holes and push grille straight on.

Use caution when
cleaning in the area of the coils..
Surfaces there may be sharp_

The air vents on the lower access panel at the rear of the
refrigerator should be cleaned periodically° Clean the vents
by using a vacuum cleaner with its dusting tool attachment
When moving the refrigerator; pull straight out. Do not shift
the refrigerator from side to side as this may tear or gouge
the floor covering Be careful not to move the refrigerator
beyond plumbing connections_

J

\

\

Air Vents on Lower Access Panels

REPLACING THE LIGHT BULB

To replace the light bulb in either compartment:

1. Unplug refrigerator_

2. Wear gloves as protection against possible broken glass_

3. Replace old bulb with an appliance bulb of the same
wattage.

4_ Remember to plug refrigerator back in.

Removing Crisper Ught Shield and Bulb (some models)

Vents

Remove

12

VACATION AND MOVING TIPS
Short vacations:

• Leave the refrigerator operating during vacations of 3
weeks or lesso

. Use up all perishable items from the refrigerator

section,

• Wrap and store other items in the freezer

• Turn off the automatic ice maker, even if you will be
gone just a few days,,

Long vacations:

• Remove all food and ice if you will be gone 1 month or

more,

• Tum the controls to OFF and disconnect the power.

• Turn off the automatic ice maker and turn the water

supply valve to the closed position_

• Clean the interior thoroughly,

- Leave both doors open to prevent odorand mold
buildup. Block open if necessary,

Moving: When moving the refrigerator, follow these
guidelines to prevent damage:

• Remove all food and other items from both the
refrigerator and freezer compartments, Empty the ice

storage bin,

If a hand truck is used in moving, load the refrigerator

from the side,

o

Turn the rollers as far up as possible. This wil! protect
them during sliding or moving.

o

The cabinet should be well padded and handled with
care° DO NOT DROP.

If it is necessary to move refrigerator through narrow
doorways, follow these steps to remove refrigerator

and freezer handles and/or doors.

TO REMOVE HANDLES

Full-length Trim

Using a putty knife, carefully slide corner of the blade
under trim. Slide blade down until you find trim lock.

Carefully maneuver blade against trim lock from the
side, as shown, Pressing down on trim lock from

above will not release it.

2 Carefully push putty knife firmly against trim lock, and

twist putty knike gently, Trim lock will snap free from
door, (Lower trim piece will have two trim locks.)

3, Grasp trim, and pull up away from handle using a slight

side-to-side motion.

4 Remove screw attaching handle to door.,
5 Repeat these steps for each handle end. Keep screws

and trim pieces.

6. Slide handle up and off dovetail buttons,
7, To replace handles, place handle over dovetail buttons,

making sure end marked TOP is up_Pul! down to align
handle holes with screw holes, Install screws Slide

upper and lower trim pieces back on handle ends, and

snap trim locks back into holes on door front

IMPORTANT

If the refrigerator is going to be stored or moved in freezing

temperatures, the water in the ice and water system must
be drained completely. Failure to do so could result in water

leaks when the refrigerator is put back in service., Contact a
service representative to perform this operation

TrimLock

Using Puey Kal_ve,Apply

PressuretoTrirnLocks Fram

The Stde and Genlly Tv4st

Removing Handles and Trlm

TO REMOVE DOORS
Before removing the doors, ensure the freezer control is

turned to OFK Remove al! the food from the doors, and
unplug the refrigerator. Remove the toe grill

Trace around the hinges with a soft lead pencil. This will
make it easier to realign the doors when they are replaced.
Completely remove one door before starting removal of the

other,

13

TO REMOVE FREEZER DOOR:

1. Remove the toe grille (see "Outside" in Care and

Cleaning Section).

2. To discor_nect water line, grip tube firmly in left hand and

use toot (located in bag under toe grille) to push in on
gray collar to release water' connector (Figure 1),

Male

Connector

W_tet Une
Connector

Hinge

Cover

Figure 2

6 Loosen, but DO NOT REMOVE, bottom lower hinge

bolt, Remove top lower hinge bott (Figure 4).

7_ Remove top hinge cover by filling back of cover and

sliding forward Remove screws mounting hinge

bracket to cabinet, Hold bracket when removing last

screw; door closer mechanism places mild spring tension
on hinge DO NOT remove hinge bracket from door.

& Carefully lift door up and off loosened lower hinge bolt

(Figure 4)

TO REMOVE REFRIGERATOR DOOR:

1.. Remove top hinge cover by lifting back of cover and
sliding forward, Remove screws mounting hinge

bracket to cabinet. Hold bracket when removing last
screw; door closer mechanism places mild spring tension

on hinge. DO NOT remove hinge bracket from door.,

2 Loosen, but DO NOT REMOVE, bottom lower hinge

bolt. Remove top lower hinge bolt

3. Carefully lift door up and off loosened lower hinge bolt.
Store doors in a safe place until refrigerator is moved to

desired location. Keep all hardware for reinstallation.

3. Remove screw to detach lower hinge cover (Figure 2).

4. To disconnect wiring harness plug connector, place your
thumbs on the flat sides of each connector' piece. Bend

both parts back and forth Then with a firm grasp, pull
the two pEecesapart as shown (Figure 3)..

Figure 31

5. Place a strip of tape along door bottom, over lower
hinge and up the side of the door_ This will hold hinge in
place when door is removed (Figure 4).

TO REINSTALL FREEZER DOOR:

1_ Position door on unit and tighten screws.

2 Reconnect the wiring connector', making sure it is locked..

To prevent electrical shock, fold wires

as shown in Figure 2. Make sure male connector

from door is pointing up. Insert tubing from door
through access hole in lower hinge cover. Position

cover over wires, ensuring they are not pinched or

exposed. Install screw to attach cover..

3._To reinstallwater line connector, push door tube firmly
into connector until connector touches the black mark on

the tube and stops (Figure 5).

r'!_ This step is critical to ensure that the

water line does not leako

Water Une

_G ir_yr Connector _ka=_

Water

L from Door Une --

Figure 5

TO REINSTALL REFRIGERATOR DOOR
To reinstall refrigerator door, reverse instructions used to

remove door.

14

AVOID SERVICE Before calling for service, review this lisL It may save you time and expense. This list

includes common occurences that are not the result of defective workmanship or

CHECKLIST materials in this appliance.

J

PROBLEM CAUSE I CORRECTION

RUNNING OF REFRIGERATOR

Compressor does not run.

Refrigerator runs too much or
too long,

• Freezer control is OFE

• Refrigerator is in defrost cycle.

e

Plug at wall outlet is

disconnected

D

House fuse blown or tripped

circuit breaker,

Power outage°
Room or outside weather is hot.

e

Refrigerator has recently been
disconnected for a period of
time

=

Automatic Ice Maker is
operating,.

Doors are opened too frequently
or too long

Refrigerator/freezer door
may be slightly open.

• Refrigerator control is set too
cold (Control found in

refrigerator section)

• Refrlgerator.freezer gasket is
dirty, worn, cracked, or poorly

fitted

• Set freezer control. See "Setting the Controls"

• This is normal for a fully automatic defrost refrigerator.
The defrost cycle occurs periodically, lasting about 20

minutes

• Ensure plug is tightly pushed into outlet

• Check/replace fuse with a 15 amp time-delay fuse Reset
circuit breaker..

• Check house lights.. Call Iocat Electric Company

• It's normal for the refrigerator to work longer under these
conditions

- It takes 8q2 hours for the refrigerator to cool down
completely.

• Ice Maker operation causes refrigerator to run slightly
more

• Warm air entering the refrigerator causes it to run more
Open doors less often.

• Ensure refrigerator is level Keep food and containers from
blocking dooJt. See PROBLEM section OPENING /

CLOSING OF DOORS/DRAWERS.

• Set refrigerator control to warmer setting until refrigerator
temperature is satisfactory Allow 24 hours for
temperature to stabilize.

• Clean or change gasket. Leaks in door seal will cause
refrigerator to run longer in order to maintain desired
temperatues.

Compressor goes off and on

frequently_

TEMPERATURES ARE TOO COLD

Freezer Temperature too cold,
Refrigerator temperature is

satisfactory.

Refrigerator temperature too
cold,, Freezer temperature is

satisfactory,
Food stored in drawers freezes.

Food stored in Meat Keeper
freezes. (Some models)

, Freezer control is set too cold

, Refrigerator control is set too

. Refrigeratorcontrol is settoo

o Chilled Air Control set too cold.

Thermostat keeps the
refrigerator at a constant
temperature.

cold.

cold

- This is normal Refrigerator goes off and on to keep
temperature constant.

• Set freezer control to a warmer setting until freezer
temperature is satisfactory Allow 24 hours for the
temperature to stabilize. Then, if refrigerator
temperature is not right, set refrigerator control to a
colder setting..

• Set refrigerator control to a warmer setting Allow 24
hours for temperatures to stabilize

• See solution above.

- Adjust Chilled Air Control to a lower setting
(Meat should be stored at a temperature just below the
freezing point for maximun fresh storage time. It is normal
for ice crystals to form due to the moisture content of
meat..)

15

PROBLEM I CAUSE I CORRECTION

TEMPERATURES ARE TOO WARM

Freezer/Refrigerator • Doors are opened too • Warm air enters the refrigerator whenever the door is
temperature is too warm, frequenty or too long opened Open the door less often

• Door is slightly open. • See PROBLEM section OPENING/CLOSING OF
DOOR/DRAWERS_

• Condenser is dirty • Clean condenser. See ='Outside" in Care and Cleaning,

Freezer temperature is too • Freezer control is set too warm • Set Freezer control to a colder setting until freezer
warm. temperature is satisfactory. Allow 24 hours for the

temperature to stabilize. Then, if refrigerator temperature

is not right, set refrigerator control to a warmer setting.

Refrigerator temperature is too • Refrigerator control is set too • Set refrigerator control to a colder setting Allow 24
warm. Freezer temperature is warm hours for the temperature to stabilize.

satisfactory.

Temperature in the Meat Keeper • Chilled Air Control is set too • Adjust Chilled Air Control to a colder setting.
ts too warm. (Some models) warm..

WATERZMOISTURE/FROST INSIDE REFRIGERATOR

Moisture collects on inside of
refrigerator walls.

o

Weather is hot and humid

Door is slightly open

• The rate of frost buildup and internal sweating increases
This is normal.

• See PROBLEM section OPENING/CLOSING OF

DOORS/DRAWERS.

Door is opened too often or too

• Open door less often.

long.

Water collects on bottom side • • It is not unusual to have moisture on the bottom side of
of drawer cover, the cover:

Water collects in bottom of • - Dry items before putting them in the drawe_. Water
drawer: collecting in bottom of drawer is normal

Vegetables contain and give off

moisture

Washed vegetables and fruit
drain while in the drawer_

WATER/MOISTURE/FROST OUTSIDE REFRIGERATOR

Moisture forms on outside of • Weather is humid.. • This is normal in humid weather_ When humidity is lower,
refrigerator' or'between doors, the moisture should disappear

• Door is slightly open, causing • See PROBLEM section OPENING/CLOSING OF
cold air from inside refrigerator DOORS/DRAWERSo

to meet warm air from outside.

AUTOMATIC ICE MAKER (some models)

Ice Maker' is not making any • Move wire signal arm to the "dowry"' or ON" position_
ice.

• Ice Maker wire signal arm is in
"up' or "OFF" position.

• Household water line valve is

, Turn on household water line valve.

not open.

• Freezer is not cold enough.

• Saddle valve on cold water
pipe is clogged or restricted by

foreign material.

• See PROBLEM section TEMPERATURES ARE TOO

WARM°

- Turn off household water line valve Remove, clean, or
replace valve.

• Check to see if the water
dispenser is dispensing water

tf not, the Kenmore ice & Water filter is clogged or

restricted by foreign material, and must be replaced..

Ice Maker ts not making enough
Ice.

• Ice Maker is producing less ice
than you expect.

o Freezer is not cold enough_

• Household water line valve is
not completely open.

• Check to see if water dispenser
isdispensing slower than

normal.

16

Ice Maker should produce approximately 2-1/;_ to 4

pounds of ice every 24 hours

e

See PROBLEM section TEMPERATURES ARE TOO

WARM,

Turn on househofd water line valve.

If it is, replace the Kenmore Ice & Water filter cartridge

/

PROBLEM CAUSE .[

AUTOMATIC ICE MAKER (Continued)

Ice Maker wilt not stop making • Ice Maker wire signal arm is • Move item and release wire signal arm Remove any ice
ice° being held down by some item cubes that are frozen together over the wire signal arm

in the freezer.

Ice Maker is not separating the • Ice cubes are not being used • Remove and shake ice bucket to separate cubes

ice cubes, frequently enough

• Ice cubes are hollow or smaller • The Kenmore Ice & Water filter could be clogged Replace
than normal filter

Ice has bad odor and taste, o Ice has picked up odor or flavor - Cover foods tightly. Discard stale ice Ice Maker will

from strong food stored in produce fresh supply
refrigerator or freezer.

• Water running to Ice Maker has - Add filter to make ice Consult a water purifying company
poor taste or odor.

ICE DISPENSER

CORRECTION

Dispenser will not dispense ice. ° Ice storage bin is empty

• Freezer temperature is set too

warm

° Household water line valve is

not open..

Freezer doer is not closed.
Ice dispensing arm has been

held in for more than 4-5
minutes

Ice dispenser is jammed,

," Ice has melted and frozen

around auger due to infrequent
use, temperature fluctuations,

and/or power outages

• Ice cubes are jammed between
Ice Maker arm and back of bin..

• Ice cubes are frozen together

,, tce cubes are hollow or smatler

than normal.

WATER DISPENSER

° When the first supply of ice isdropped intothe bin, the

dispenser should operate.

• Turn freezer control to a higher setting so that ice cubes
wilt be made Wi_en firstsupply of ice is made, dispenser
should operate

• Open household water tine valve. Allow sufficient time for
the ice to be made When ice is made, the dispenser

should operate

- Ensure freezer door is closed.

• Motor is overloaded Motor overload protector will reset in
approximately 3 minutes Ice can then be dispensed

• Remoce ice storage bin, thaw, and empty the contents.
Clean bin, wipe dry, and replace in proper position When

new ice is made, dispenser should operate

• Remove ice cubes that are jamming the dispenser

° Use the dispenser often so that cubes do not freeze

together

° The Kenmore Ice & Water filter could be clogged. Reptace

the filterr Dispensing system operates best at 30-I20 psi
water pressure Well water system pressures should fall

within this range

Dispenser will not dispense

water,

Water has an odd taste and/or
odor.

Water pressure is extremely ° Cut-off and cut-on pressures are o Have someone turn up the cut-off and cut-on pressure on

low. too low. (Well Systems Only) the water pump System (Well Systems Only)

• Household water llne valve is
not open

Freezer door is not closed.
Kenmore lce& Water filter is

clogged.

• Water has been in the tank for a
period of time.

,, Unit not propedy connected to

cold water line

,* Tubing used in the household

water supply and installation
may affect water taste and odor.

• - Contact water treatment plant for help,

Water has high minerai content

17

• Open household water line valve See PROBLEM seclion
"Ice Maker Is not makingany ice."

° Ensure freezer door is closed

• Replace filter

° Draw and discard 10-11 glasses of water to freshen the

supply and completely rinse out the tank.

• Connect unit to cold water line that supplies water to the

kitchen faucet

• For best results, use copper tubing for water connection

PROBLEM CAUSE CORRECTION

ODORS IN REFRIGERATOR

Interior is dirty. • Interior needs to be cleaned • See Section Care and Cleaning_

° Food with strong odor is in • Cover food tightly

refrigerator:

OPENING/CLOSING OF DOORS/DRAWERS

Door(s) will not close.

Drawers are difficult to move.

Light bulb is not on.

• Door isnot designed to swing
shut automatically

• Door was closed too hard,
causing other door to open

slightly,

• Refrigerator is not level It rocks
on the floor when moved

slightly

° Refrigerator is touching the wail

or cabinet

° Food is touching shelf on top of

drawer

• Track that drawers slide on is
dirty,

° Light bulb is burned out,

• Light switch is stuck.

No electric current is reaching
refrigerator,

• Close door securely

° Close both doors gently

. Ensure floor is level and solid, and can adequately support

the refrigerator Contact a carpenter to correct sagging or

stoping floor,

• Ensure floor is level, and can adequately support
refrigerator Contact carpenter to correct a sagging or

s_oping floor:

Keep less food in drawer

• Clean drawer, ro!lers, and track

• See "Replacing the Light Bulb" in Care and Cleaning

• Light switch is located on interior door frame next to

temperature control in each compartment Push in plunger
to release_

- See PROBLEM section RUNNINGOF REFRIGERATOR

18