Congratulations on your purchase of a new refrigerator! We
here at Sears are very proud of our product and we are
completely committed to providing you with the best
service possible. Your satisfaction is our #1 priority.
We know you’ll enjoy your new refrigerator and Thank You
for choosing our product. We hope you consider us for
future purchases.
PLEASE READ AND SAVE THESE
INSTRUCTIONS
This Owner’s Guide provides specific operating
instructions for your model. Use your refrigerator only as
instructed in this manual. These instructions are not meant
to cover every possible condition and situation that may
occur. Common sense and caution must be practiced
when installing, operating and maintaining any appliance.
Please record your model and serial numbers below
for future reference.This information is found on the
serial plate located inside the refrigerator
compartment.
'■'';NOTE:,:Use only soap and water to clean serial plate.
Model Number: 253
• Do not store or use gasoline, or other flammable liquids
in the vicinity of this or any other appliance. Read product
labels for warnings regarding flammability and other
hazards.
® Do not operate the refrigerator in the presence of
explosive fumes.
• Avoid contact with any moving parts of automatic ice
maker.
• Remove all staples from the carton. Staples can cause
severe cuts, and also destroy finishes if they come in
contact with other appliances or furniture.
CHILD SAFETY
Destroy or recycle the carton, plastic bags, and any
exterior wrapping material immediately after the refrigerator
is unpacked. Children should NEVER use these items to
play. Cartons covered with rugs, bedspreads, plastic
sheets or stretch wrap may become airtight chambers,
and can quickly cause suffocation.
Child entrapment and
suffocation are not problems of
the past. Junked or abandoned
refrigerators or freezers are still
dangerous - even if they will sit
for “just a few days.” If you are
getting rid of your old refrigerator
or freezer, please follow the
instructions below to help
prevent accidents.
Before you throw away your old refrigerator/freezer:
• Remove doors.
• Leave shelves in place so children may not easily climb
inside.
• The refrigerator must be plugged into its own
dedicated 115 Volt, 60 Hz., AC only electric outlet
The power cord of the appliance is equipped with a
three-prong grounding plug for your protection against
electrical shock hazards. It must be plugged directly
into a properly grounded three-prong receptacle. The
receptacle must be installed in accordance with local
codes and ordinances. Consult a qualified electrician.
Do not use an extension cord or adapter plug.
• Immediately repair or replace any power cord that
becomes frayed or damaged.
• Never unplug the refrigerator by pulling on the power
cord. Always grip the plug firmly, and pull straight out
from the receptacle to prevent damaging the powercord.
• Unplug the refrigerator before cleaning and before
replacing a light bulb to avoid electrical shock.
• Performance may be affected if the voltage varies by
10% or more. Operating the refrigerator with insufficient
power can damage the compressor. Such damage is
not covered under your warranty.
• Do not plug the unit into an outlet controlled by a wall
switch or pull cord to prevent the refrigerator from being
turned off accidentally.
• Avoid connecting refrigerator to a Ground Fault Interruptor
(G FI) circuit.
KENMORE REFRIGERATOR WARRANTY
ONE YEAR FULL WARRANTY ON
REFRIGERATOR
For one year from the date of purchase, when this
refrigerator is operated and maintained according to
the instructions supplied with it, Sears will repair this
refrigerator, free of charge, if defective in material or
workmanship. This one year time period does not
include the refrigerator water filter cartridge (if
equipped), which is an expendable part warranted for
only 30 days (see below).
FIVE YEAR FULL WARRANTY ON SEALED
REFRIGERATION SYSTEM
For five years from the date of purchase, when this
refrigerator is operated and maintained according to
the instructions supplied with it, Sears will repair the
sealed system (consisting of refrigerant, connecting
tubing, and compressor), free of charge, if defective
in material or workmanship.
30 DAY FULL WARRANTY ON WATER FILTER
CARTRIDGE (if equipped)
For thirty days from the date of purchase, Sears will
replace the refrigerator water filter cartridge if it is
defective in material or workmanship.
All above warranty coverage applies only to
refrigerators which are used for storage of food for
private household purposes.
iMPOBTANT: Turning the ■Freezer.'and :F,resh .T.o.od ■■" ■
■.Cont.rols to “OTturos, off the compressor an.d prevents. ■;■■
..your refrigerator from cooling,'but does.not .disconnect'
.|he.-p.o.wer..todhe light, b.ulb: and .other 'electrical.- ■
'.'components. To turn .off power to your refrigerator, 'you ''. :'■'
..m.u.s.t.unplug .the. power cord from, the wall receptacle.' ■
Grounding type
wall receptacle
Do not, onder
any circumstances,
cut, remove,
or bypass the
grounding prong,
Power cord With '
3-prong grounded plug
Warranty service is available in the United States or
Canada by contacting Sears at 1-800-4-MY-FIOME®
(1 -800-469-4663).
This warranty applies only while this product is in use
in the United States or Canada. This warranty gives
you specific legal rights, and you may also have other
rights which vary from state to state or province to
province.
Sears, Roebuck and Co., Dept. 817WA, Hoffman
Estates, IL60179
new Kenmore® product is designed and manufactured
for years of dependable operation. But like all
products, it may require preventive maintenance or
repair from time to time. That’s when having a Master
Protection Agreement can save you money and
aggravation.
Purchase a Master Protection Agreement now and
protect yourself from unexpecfed hassle and expense.
The Master Protection Agreement also helps extend
the life of your new appliance. Here’s what’s included
in the Agreement:
У Expert service by our 12,000 professional repair
specialists
У Unlimited service and no charge for parts and
labor on all covered repairs
У“No-lemon” guarantee - replacement of your
covered product if four or more product failures
occur within twelve months
у Product replacement if your covered product
can’t be fixed
у Annual Preventive Maintenance Check at your
request - no extra charge
УFast help by phone - phone support from a
Sears technician on products requiring in-home
repair, plus convenient repair scheduling
УPower surge protection against electrical
damage due to power fluctuations
УRental reimbursement if repair of your covered
: l.il'.
product takes longer than promised
Once you purchase the Agreement, a simple phone
call is all that it takes for you to schedule service. You
can call anytime day or night, or schedule a service
appointment online.
In Canada
Maintenance Agreements
Your purchase has added value because you can
depend on Sears HomeCentral® for service. With over
2400 Service Technicians and more than a million
parts and accessories, we have the tools, parts,
knowledge and skills to back our pledge:
We Service What We Sell.
Your Kenmore® product is designed, manufactured
and tested to provide years of dependable operation.
But like all products, it may require service from time to
time. The Sears Maintenance Agreement otters you an
outstanding service program, affordably priced.
The Sears Maintenance Agreement
• Is your way to buy tomorrow’s service at today’s
price.
• Eliminates repair bills resulting from normal wear
and tear.
• Provides phone support from a Sears technician
on products requiring in-home repair.
• Even if you don’t need repairs, provides an annual
Preventive Maintenance Check, at your request, to
ensure that your product is in proper running
condition.
Some limitations apply. For more Information
about concerning Sears Canada Maintenance
Agreements, call 1-800-361-6665.
Sears has over 12,000 professional repair specialists,
who have access to over 4.5 million quality parts and
accessories. That’s the kind of professionalism you
can count on to help prolong the life of your new
purchase for years to come. Purchase your Master
Protection Agreement today!
Some limitations and exclusions apply. For prices
and additional Information, call 1-800-827-6655.
Sears Installation Service
For Sears professional installation of home appliances
and items like garage door openers, water heaters,
and other major home items, in the U.S.A. call
1-800-4MY-HOME®.
0 1
This Owner’s Guide provides specific operating
instructions foryour model. Use the refrigerator only as
instructed in this Use & Care Manual. Before starting the
refrigerator, follow these important first steps.
LOCATION
• Choose a place that is near a grounded electrical outlet.
Do Not use an extension cord or an adapter plug.
• If possible, place the refrigerator out of direct sunlight
and away from the range, dishwasher or other heat
sources.
• The refrigerator must be installed on a floor that is level
and strong enough to support a fully loaded refrigerator.
» Consider water supply availability for models equipped
with an automatic ice maker.
INSTALLATION
...................
............. ... ,
Do Not install the refrigerator where.■
The temperature .will drop below,.55°F (13°C) or;r,ise
; a.bove 110.“F,,(43°C). The compressor will not be able .
;to maintain'pro.per-temperatures insideThe
; refrigerator. ; h ..
i^CAUTION
D.o Not block the toe grille on.the
Tower front of .your refrigerator. Sufficient air circulation
is essential 'for the proper operation 'of 'your
'refrigerator. C
Installation Clearances
* Allow the following clearances for ease of installation,
proper aircirculation, and plumbing and electrical
connections:
Sides & Top
Back
--------------------------
...■...:...:...:...:...:...:...:...:...:...
----------------
3/8”
1”
DOOR OPENING
NOTE: If you refrigerator is placed.-with th.e door .hinge, ; ■
. side against a...wa!l, you may have i.o...a!low additional
space so the door can be opened wider.
Your refrigerator should be positioned to allow easy access
to a counter when removing food. For best use of drawers
and freezer baskets, the refrigerator should be in a
position where both the refrigerator and freezer doors can
be fully opened.
To Install Toe Grílle:
1. Open freezer and
fresh food
compartment doors.
2. Line up toe grille at
base of refrigerator,
making sure the four
bottom tabs are
resting through holes
at base of cabinet.
3. Starting from left side
of toe grille, press in on first top tab using your thumb
and push toe grille forward until it snaps in place. Continue
this process until all tabs aresnapped in place and toe
grille is secured to refrigerator.
Cabinet
LEVELING
All four corners of your refrigerator must rest firmly on a
solid floor. Your refrigerator is equipped with adjustable
front rollers to help level your unit. To ensure proper door
seal and assist door closing, the refrigerator should be
tilted 1/4” (6 mm), front to back.
To Level Your Refrigerator:
1. Remove toe grille. (See “To Remove Toe Grille”.)
2. Use flat-blade screwdriver or 3/8” socket wrench
to adjust front rollers.
■■ ■NOTEr.The.fefrigeratord.oors'.are designed to shut by.,
'-'themselves'withina20degree..openi,o,g.,',.,'.L-.'"-- ' '■ '
Rai se
m.
i
TOE GRILLE INSTALLATION / REMOVAL
To Remove Toe Grille:
1. Open freezer and fresh food compartment doors.
2. Working from left side of toe grille, slip your fingers between
top of toe grille and cabinet. Gently pull forward until first set of
tabs are free. Slide your hand down past the free tabs and pull
forward again until the second set of tabs are free. Continue
this process until all tabs are free and the toe grille can be
removed. {See graphic at top of page in right column.)
: ■ V V -O .
3.Check both doors to be sure seals touch cabinet on all
four sides.
lnst3lÍ3tíOn ~ Connecting Ice M.aker To Water Supply
A WARNING
_____
J .'To a¥oid electric shock, which can cause death or severe personal injury, disconnect the refrigerator
■■from electrical power before connecting a.watersupplf.line to the refrigerator.. ■■■■: ■. ■. ■■ .-.■■...■■■;
ikCAUTION
To Avoid. Property Damage:
Copper .tubing is recommended for the water supply line. Water supply .tubing, made of %” plastic is not
. .'recommeodecl.since.it greatly .increases the. potential for water leaks. Manufacturer will not be .responsible
..Tor any damage if plastic tubing is used for'Supply.line. ■ ■■■ ■■■'.■.'■ .-■...
■ 'Chemicals from a malfunctioning softener c.an.damage the ice maker. If the ice maker is connected to.so.ft
wate.r, ensure.thatthesoften.e.r.is.maintaine.d and working prope.rly.' ■ ■■..■■■■■'■ ■■■.'■■.■.. ....: '■■....■■.. ■..■..
IMPORTANT: Ensure that your water supply line.co.nnections'comply with all local plumbing codes. ■'
Before Installing The Water Supply Line, You Will Need
» BasicTools: adjustable wrench, flat-blade screwdriver, and Phillips'’'“ screwdriver
® Access to a household cold water line with water pressure between 20 and 100 psi.
• A water supply line made of inch {6.4 mm) OD, copper tubing. To determine the length of copper tubing needed,
you will need to measure the distance from the ice maker inlet valve at the back of the refrigerator to your cold water
pipe. Then add approximately 7 feet (2.1 meters), so the refrigerator can be moved out for cleaning (as shown).
® A shutoff valve to connect the water supply line to your household water system. DO NOT use a self-piercing type
shutoff valve.
» A compression nut and ferrule (sleeve) for connecting the water supply line to the ice maker inlet valve.
NOTE: A water line kit.is available from your appliance, dealer at .additional .cost..,lt contains 2,5 feet (7.6 meters),'of ,14 ■
inch.OD.copper tubing, a saddle,type shutoff yalye'{nonpiercing),'(2) 14 inch brass compression nuts, (2) ferrules/
'sleeves,'and instructions for installing a water supply line.
.........■..■..■..■..■..■..■..■... ■•■;
......'....'.....'....'.....
....
.
(Iff!: - Jo Connect Water Supply Line To ice Maker Inlet Walwe
Disconnect refrigerator from electric power source.
Place end of water supply line into sink or bucket. Turn ON water supply
and flush supply line until water is clear. Turn OFF water supply at shut
off valve.
\ ill:.;
Unscrew plastic cap from water valve inlet and discard cap.
Slide brass compression nut, then ferrule (sleeve) onto water supply line,
as shown.
Push water supply line into water valve inlet as far as it will go (% inch).
Slide ferrule (sleeve) into valve inlet and finger tighten compression nut
onto valve. Tighten another half turn with a wrench; DO NOT over tighten.
With steel clamp and screw, secure water supply line to rear panel of
refrigerator as shown.
7.
Coil excess watersupply line (about 214 turns) behind refrigerator as shown
and arrange coils so they do not vibrate or wear against any other surface.
8.
Turn ON water supply at shutoff valve and tighten any connections that
leak.
9.
Reconnect refrigerator to electrical power source.
10.
Make sure ice maker power switch is turned On (See page 15 for location of
power switch).
■|M.PORTANT:.:ft.,ta.kes','app,roximately 24,.h.o.u,rs -for the .ice maker.to 'begin. p.roducing ice. Air in, ne.w plumbing lines.may..-'
■■cause ice. maker to cycle, two.orthree.times before.making a full tray of ice. New plumbing maycause.ice.to.be discolored
or have poorflavor. Discard ice.made during the first 24 hours. 1
..:..:..:..:..:..:..:..:..:..:..:..:..
:...............................................
TO DISCONNECT.'• ' . .
: 1. Press outer ring a.gainsi face
offitirg rWr-i
^^8 2. Puli to
'■ remove tube
TO CONNECT
hy
Inserì tube arrd
push until marK toucnes face of .fitting
t
-] _ !
'Door/Eemowai ■Instructions':-
DOOR REMOVAL INSTRUCTIONS:
If it is necessary to move the refrigerator through narrow doorways,
follow these steps to remove the doors.
'.IMPORTANT: Before you begin., turn Freezerand Fres/i'Foodcontrols
and rernove electrical power cord from 'wall outlet.'Remove any ..
■ food from door shelves.' a ............... . ...
1. Disconnect electrical supply.
2. Open both doors, then remove toe grille.
3. Close doors.
To Remove Refrigerator Door:
1. Remove top hinge cover screw on refrigerator door and remove cover.
2. Trace around hinge with soft lead pencil. This will make it easier to realign
doors when they are replaced.
3. Remove top hinge and lift refrigerator door off bottom hinge pin. Set door
aside.
4. Remove bottom hinge, if necessary.
5. Reverse this procedure to reinstall refrigerator door.
To Remove Freezer Door:
1. Disconnect water line coming from lower hinge of freezer door at connection
located under front of freezer: Press outer ring against face of fitting, then pull
to remove tube.
2. Remove top hinge cover screw on freezer door and remove cover.
3. Disconnect wiring harness connector plug at top hinge: place your thumbs on
flat sides of each connector and bend both parts back and forth, then with
firm grasp, pull both pieces apart.
4. Trace around hinge with soft lead pencil. This will make it easier to realign
doors when they are replaced.
5. Remove top hinge, allowing wiring harness to pull through hinge and lift freezer
door off of bottom hinge pin. Lay door down flat to avoid kinking water line.
6. Remove bottom hinge, if necessary.
7. Reverse this procedure to reinstall freezer door.
When both doors have been reinstalled, connect water line by inserting tube and
push until mark touches face of fitting, replace toe grille and plug in electrical power
cord. Turn both temperature controls to center position. Adjust settings as necessary.
usi=>*:.
features AlA'-Giance
' Dairy Door
Door Bin
' Wine Rack
Door Bin
Meat Keeper
and Cover
■ SptliProof™
Fixed Shelf
' Door Bin
■ Egg Tray
Special Item
' Rack
Features may wary according to model
■ Tall Bottle
Retainer
Snugger
Crisper Pan
and Cover
Fixed
Door Bin
Loading...
+ 16 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.