Kenmore 25322742410, 25322442412, 25322442411, 25322442410, 25322042410 Owner’s Manual

...

Use & Care Guide

Manual de Uso y Cuidado

Guide d uhl_sahon et d entrehen

English / Espaiol/Franc;ais

ModeJs/ModeJos/Mod_Jes: 253.12112*, 12402*, 12502*, 12512*, 12702*, 12912*,

21042", 21242", 22042", 22442", 22452", 22742*

I<e

Congelador Cong@

P/N A01062001 (1408) Sears Brands Management Corporation

Hofl:man Estates, IL 60179 UoS.A. www.kenmore.com

www.sea rs.com

Sears Canada inc. Toronto, Ontario, Canada M5B 2C3

www.sea rs.ca

Record Model/

important Safety'

Serial Numbers

Please read and save

these instructions

This Use & Care Guide provides specific operating instructions for your model. Use

your unit only as instructed in this guide. These instructions are not meant to cover

every possible condition and situation that may occur. Common sense and caution must

be practiced when installing, operating, and maintaining any appliance.

Please record your model and seriaJ numbers beJow for future reference. This

information is found on the serial plate

located inside the appliance compartment.

Model Number: 253.

instructions

Safety Precautions

Do not attempt to install or operate your unit until you have read the safety precautions in this manual. Safety items throughout this manual are labeled with a Danger, Warning,

or Caution based on the risk type.

Definitions

_This is the safety alert symbol. It is used to alert you to potential personal injury hazards.

Obey all safety messages that follow this symbol to avoid possible injury or death.

DANGER

DANGER indicates an immlnenfly

hazardous situation which, if not avoided,

will result in death or serious injury.

Serial Number: Purchase Date:

iMPORTANT

Use only soap and water to clean

serial plate.

Table of Contents

RecordModel/SeriaJ Numbers..................... 2

important Safety instructions....................... 2

Warranty information ................................. 4

Master Protection Agreements.................... 5

First Steps................................................. 6

Energy-Saving Tips..................................... 8

Setting the Temperature ¢ontroJ................. 9

Optional Features..................................... 9

Care& CJeaning........................................ 10

Power/Freezer Failure.............................. 13

Before You Carl........................................ 13

_ WARNING

WARNING indicates a potenfialJy

hazardous situation which, if not avoided,

could result in death or serious injury.

_ CAUTION

CAUTION indicates a potentialJy hazardous situation which, if not avoided,

may result in minor or moderate injury.

iMPORTANT

Indicates installation, operation, or

maintenance information which is

important but not hazard-related.

_ WARNING

Please read all safety instructions before using your new appliance.

For Your Safety

* Do not store or use gasoline or other

flammable liquids in the vicinity of this or any other appliance. Read product labels for warnings regarding flammability and

other hazards.

• Do not operate the unit in the presence of explosive fumes.

important Safety instructions

• Remove and discard any spacers used to secure the shelves during shipping. Small objects are a choke hazard to children.

• Remove all staples from the carton. Staples can cause severe cuts and also destroy finishes if they come in contact

with other appliances or furniture.

WARNING

These guidelines must be followed to

ensure that safety mechanisms in this

unit wli[ operate properly.

Electrical information

Child Safety

Destroy or recycle the carton, plastic bags, and any exterior wrapping material immediately after the unit is unpacked. Children should never use these items to play. Cartons covered with rugs, bedspreads, plastic sheets or stretch wrap may become airtight chambers and can quickly cause suffocation.

Proper Disposal of your Appliance

Risk of child entrapment Child entrapment and suffocation are not

problems of the past. Junked or abandoned appliances are still dangerous = even if they will sit for "just a few days." if you are getting rid of your appliance, please follow the instructions below to help prevent accidents.

Before you throw away your old unit:

, Remove door. " Leave shelves in

place so children may not easily

climb inside.

* Have refrigerant

removed by a qualified service technician.

iMPORTANT

Your old unit may have a cooling system that

used CFCs or HCFCs (chlorofluorocarbons

or hydrochlorofluorocarbons). CFCs and

HCFCs are believed to harm stratospheric

ozone if released to the atmosphere.

Other refrigerants may cause harm to the environment if released to the atmosphere. If you are throwing away your old unit, make sure the refrigerant is removed for proper disposal by a qualified technician. If you

intentionally release refrigerant, you may be subject to fines and imprisonment under the

provisions of environmental legislation.

• The appliance must be plugged into its own dedicated 115 Volt, 60 Hz., AC only electric outlet. The power cord of the appliance is equipped with a three-prong grounding plug for your protection against

electrical shock hazards, it must be plugged directly into a properly grounded

three-prong receptacle. The receptacle must be installed in accordance with local

codes and ordinances. Consult a qualified electrician. Do not use an extension cord

or adapter plug.

• immediately repair or replace any power cord that becomes frayed or damaged.

• Never unplug the appliance by puffing on the power cord. Always grip the plug firmly, and puff straight out from the receptacle to prevent damaging the

power cord.

• Unplug the appliance before cleaning and before replacing a light bulb to avoid

electrical shock.

* Performance may be affected if the

voltage varies by 10% or more. Operating the unit with insufflcient power can damage the motor. Such damage is not covered under the warranty.

° Do not plug the unit into an outlet

controlled by a wall switch or pull cord to prevent the appliance from being turned off: accidentally.

Avoid connecting unit to a Ground Fault Circuit Grounding type wall receptacle

Interruptor (GFCI). Do not, under

any circumstances, cut, remove,

or bypass the

grounding prong,

Power cord with 3-prong grounded plug

Warranty information

KENMORE LIMITED WARRANTY

FOR ONE YEAR from the date of sale this appliance is warranted against defects in material or workmanship when it is installed, operated and maintained according to all

supplied instructions. WITH PROOF OF SALE, a defective product will receive free repair or replacement at

option of seller. To arrange for warranty service, call 1-800-4-MY-HOME ®

If this appliance is ever used for other than private family purposes, this warranty applies

for only 90 days from sale date in the United States, and is void in Canada.

This warranty covers ONLY defects in material and workmanship, and

will NOT pay for:

1. Expendable items that can wear out from normal use, including but not limited to

filters, belts, bags and screw-in base light bulbs.

2. A service technician to instruct the user in correct product installation, operation

or maintenance.

3. A service technician to clean or maintain this product.

4. Damage to or failure of this product if it is not installed, operated or maintained according to all instructions supplied with the product.

5. Damage to or failure of this product resulting from accident, abuse, misuse or use for other than its intended purpose.

6. Damage to or failure of this product caused by the use of detergents, cleaners, chemicals or utensils other than those recommended in all instructions supplied with

the product.

7. Damage to or failure of parts or systems resulting from unauthorized modifications

made to this product.

Disclaimer of implied warranties; limitation of remedies

Customer's sole and exclusive remedy under this limited warranty shall be product repair as

provided herein. Implied warranties, including warranties of merchantability or fitness for

a particular purpose, are limited to one year or the shortest period allowed by law. Sears shall not be liable for incidental or consequential damages. Some states and provinces do

not allow the exclusion or limitation of incidental or consequential damages, or limitation

on the duration of implied warranties of merchantability or fitness, so these exclusions or

limitations may not apply to you.

This warranty applies only while this appliance is used in the United States or Canada _. This warranty gives you specific legal rights, and you may also have other rights which vary

from state to state.

In-home repair service isnot available in all Canadian geographical areas, nor will this

warranty cover user or servicer travel and transportation expenses if this product is located in a

remote area (as defined by Sears Canada Inc.) where an authorized servicer is not available.

Sears Brands Management Corporation, Hoffman Estates, IL 60179 Sears Canada Inc., Toronto, Ontario, Canada M5B 2C3

Master Protection Agreements

Congratulations on making a smart purchase. Your new Kenmore ® product is designed and manufactured for years of dependable operation. But like all products, it may

require preventive maintenance or repair from time to time. That's when having a Master Protection Agreement can save you money and aggravation.

The Master Protection Agreement also helps extend the life of your new product. Here's what the Agreement s includes:

* Parts and labor needed to help keep products operating properly under normal use, not

just defects. Our coverage goes weU beyond the product warranty. No deductibles, no

functional failure excluded from coverage - real protection.

* Expert service by a force of more than 10,000 authorized Sears service technicians,

which means someone you can trust will be working on your product.

* Unlimited service calls and nationwide service, as often as you want us, whenever you

want us.

* "No-lemon" guarantee - replacement of your covered product if four or more product

failures occur within twelve months.

" Product replacement if your covered product can not be fixed. "Annual Preventive Maintenance Check at your request - no extra charge. " Fast help by phone - we call it Rapid Resolutlon - phone support from a Sears

representative on all products. Think of us as a "talking

owner's manual".

* Power surge protection against electrical damage due to power fluctuations. * $250 Food Loss Protection annually for any food spoilage that is the result of

mechanical failure of any covered refrigerator or freezer.

" Rental reimbursement if repair of your covered product takes longer than promised.

* 25% discount off: the regular price of any non-covered repair service and related

installed parts.

Once you purchase the Agreement, a simple phone call is all that it takes for you to schedule service. You can call anytime day or night, or schedule a service appointment online.

The Master Protection Agreement is a risk free purchase. If you cancel for any reason during the product warranty period, we will provide a fuji refund. Or, a prorated refund anytime after the product warranty period expires. Purchase your Master Protection Agreement today!

Some limitations and exclusions apply. For prices and additional information in the U.S.A. call 1-800-827-6655.

Coverage in Canada varies on some items. For full details call Sears Canada at 1-800-361-6665.

Sears Installation Service For Sears professional installation of home appliances, garage door openers, water

heaters, and other major home items, in the U.S.A. or Canada call 1-800-4-MY-HOME ®.

First Steps

This Use & Care Guide provides general installation and operating instructions for your model. We recommend using a

service or kitchen contracting professional to install your appliance. Use the unit only

as instructed in this Use & Care Guide. Before starting the appllance, follow these

important first steps.

Location

* Choose a place that is near a grounded,

non-GFCI, electrical outlet. Do Not use an extension cord or an adapter plug.

* For the most efficient operation, the unit

should be located where surrounding

temperatures will not exceed ]]0°F (43°C).

Temperatures of 32°F (0°C) and below

will NOT affect operation. Additional

compressor heaters are not recommended.

" Allow space around the unit for good

air circulation. Leave a 3 inch (75 mm) space on all sides of the appliance for adequate circulation.

NOTE

The exterior walls of the appliance may become quite warm as the compressor

works to transfer heat from the inside.

Temperatures as much as 30°F warmer

than room temperature can be expected.

For this reason it is particularly important in hotter climates to allow enough space

for air circulation around your unit.

Leveling

The unit must have all bottom corners resting firmly on a solid floor. The floor must be strong enough to support a fully loaded appliance.

NOTE

It is Very Important for your appliance to

be level in order to function properly. If the unit is not leveled during installation, the door may be misaligned and not close

or seal properly, causing cooling, frost, or

moisture problems.

To Level Upright Models:

3" (75

iiiiiiiii_ii_i!_!i

3" (7Lmm)

_' 3 (75 ram)

3"(75 mm)

1"(25 turn)

(75 mm)

After discarding crating screws, use a carpenter's level to level the unit from front-

to-back. Adjust the plastic leveling feet in front, 1/2 bubble higher, so that the door closes easily when left halfway open.

To Level Chest Models:

ff needed, add metal or wood shims between foot pads and floor.

Cleaning (Prior to use)

* Wash any removable parts, the appliance

interior, and exterior with mild detergent

and warm water. Wipe dry. Do not use harsh cleaners on these surfaces.

" Do not use razor blades or other

sharp instruments, which can scratch the appliance surface when removing

adhesive labels. Any glue left from the tape can be removed with a mixture of warm water and mild detergent, or touch

the residue with the sticky side of tape already removed. Do not remove the

serial plate.

First Steps

CAUTION

To allow door to dose and seal properly,

DO NOT let food packages extend past

the front of shelves.

Slide the shelf grommet into the grommet already in the unit wall until

it is flush.

To install the shelf grommet to the shelf:

1. With the wire shelf installed, press the shelf grommet down onto the wire that

is anchored into the appliance wall. Be sure to keep the larger end of the shelf grommet away from the wall.

2. Push the shelf grommet onto the wire until it snaps in place.

To install the handle clips to the basket:

1. Place the basket on a firm, flat surface.

2. With the narrow side of the handle clip on the inside of the basket, snap

the handle clip to the recessed area in the basket.

First Steps Energy Saving Tips

Once the inside surface snaps in place, continue the process by roiling

the handle dip slightly outward and pressing down firmly to snap

onto the outside surface. If installed incorrectly, the handle clip will not

lay fiat.

• The appliance should be located in the coolest area of the room, away from heat producing appliances or heating ducts, and out of direct sunlight.

Removed if door must be removed: Gently lay the unit on its back, on a

rug or blanket.

2. Remove 2 base screws and base panel.

3. Remove wire from clips on bottom of cabinet if required.

4. Unplug connector, if required, by holding the cabinet connector in place and pulling the door connector out.

5. Remove bottom hinge screws.

6. Remove plastic top hinge cover.

7. Remove screws from top hinge.

8. Remove top hinge from cabinet.

9. Remove door and bottom hinge from cabinet.

• Let hot foods cool to room temperature before placing in the unit. Overloading

the appliance forces the compressor to run longer. Foods that freeze too slowly may lose quality or spoil

• Be sure to wrap foods properly, and wipe containers dry before placing them in the

unit. This cuts down on frost build-up inside.

• Shelves should not be lined with aluminum foil, wax paper, or paper toweling. Liners

interfere with cold air circulation, making the unit less efficient.

Organize and label food to reduce door openings and extended searches. Remove

as many items as needed at one time, and dose the door as soon as possible.

10. To replace door reverse the above order, and securely tighten all screws

to prevent hinge slippage.

Setting the Temperature Control

Optional Features

Cool Down Period

* For safe food storage, allow 4 hours for

the appliance to cool down completely.

The unit will run continuously for the first several hours. Foods that are already frozen may be placed in the appliance

after the first few hours of operation. Unfrozen foods should NOT be loaded

into the unit until the freezer has operated for 4 hours.

* When loading the appliance, freeze only

3 pounds of fresh food per cubic foot of

space at one time. Distribute packages to be frozen evenly throughout the unit. It is not necessary to turn the control knob to a

colder setting while freezing food.

Temperature Control

Electromechanical Temperature Control (some chest and upright models)

The electromechanical temperature control is located inside the appliance on upright

models, and on the left exterior wall on chest models. The temperature is factory preset to provide satisfactory food storage

temperatures. However, the temperature control is adjustable to provide a range of temperatures for your personal satisfaction.

To adjust the temperature setting, turn the temperature control knob clockwise or

counterclockwise. Allow several hours for the temperature to stabilize between adjustments.

OFF_

NOTE

Your appliance may have some, or all of

the features listed below. Become familiar with these features, and their use and care.

Security Lock with Pop-Out Key

This security lock fastens the door snugly, ensuring stored food is secure. To lock or unlock the freezer, push the key into the lock

and turn. The key pops out of the lock after it has been turned.

Blue Defrost Button (some chest models)

iMPORTANT

It is time to defrost and clean the freezer

when the blue defrost button is completely

covered with frost.

Blue Defrost Button

Temp Alarm

This feature is designed to provide a warning if the inside temperature reaches an unsafe

level. The temperature feature operates on household electricity. It will not function if

household electricity is interrupted.

To silence the alarm, press the set button next to the ALARM OFF indicator on the

display or any key on the control panel.

Interior Light

The light comes on automatically when the door is opened. To replace the light bulb, turn the temperature control to OFF and unplug the electrical cord. Replace the old

bulb with a bulb of the same wattage.

Optional Features Care & Cleanincj

Adjustable interior Shelves (some upright models)

Multi-position adjustable interior shelves can be moved to any position for larger or

smaller packages. The shipping spacers that stabilize the shelves for shipping may be

removed and discarded.

_ CAUTION

Damp objects stick to cold metal

surfaces. Do not touch interior metal surfaces with wet or damp hands.

Some upright freezers are frost-free and defrost automatically, but should be cleaned occasionally.

Between Defrostings

To avoid frequent defrosting, occasionally use a plastic scraper to remove frost. Scrape

with a pulling motion. Never use a metal

instrument to remove frost.

Defrosting

_ CAUTION

Freezer must be unplugged (to avoid

electrical hazard) from power source when defrosting unit.

Smart Basket TM System {some chest rnodels)

This basket helps organize odd-shaped items. To reach other packages in the freezer, slide the basket aside or lift out.

It is important to defrost and clean the

freezer when 1/4 to 1/2 inch of frost has accumulated. Frost may tend to accumulate

faster on the upper part of the freezer due to warm, moist air entering the freezer when the door is opened. Remove food and leave

the door open when defrosting the freezer. To Defrost Upright Models with Defrost Drain:

Remove the drain plug on the inside floor of the freezer by pulling it straight out.

To access external drain tube on models with a base panel, first remove the two screws

from the base panel. Locate the drain tube near the left center under the freezer.

Place a shallow pan under the drain tube. Defrost water will drain out. Check

the pan occasionaffy so water does not overflow (see figure 1).

Care & Cleanincj

• A 1/2 inch garden hose adapter can be

used to drain the freezer directly into a floor drain. If your model is not equipped

with an adapter, one can be purchased at

most hardware stores.

" Replace the drain plug when defrosting

and cleaning are completed. If the drain is left open, warm air may enter the freezer.

Drain Pan )

Hose

Defrost /

Drain

Plug

Figure 3

* Pull out the drain plug inside the freezer

(see figure 4). Defrost water will drain out. Check pan occasionally so water does

not overflow.

Figure 1

To Defrost Chest Models with Defrost Drain:

* Place a shallow pan beneath the drain

outlet. Pull out the outside drain plug (see figure 2). A 1/2inch garden hose adapter can be used to drain the freezer directly into

a floor drain (see figure 3). If your model is not equipped with an adapter, one can be purchased at most hardware stores.

Drain Plug

Figure 2

Figure 4

• Replace the drain plugs when defrosting and cleaning are completed. If the drain is

left open, warm air may enter the freezer.

To Defrost Models without Defrost Drain:

Place towels or newspapers on the freezer bottom to catch the frost. The frost will

loosen and fall.

" Remove the towels and/or newspapers.

• If the frost is soft, remove it by using a

plastic scraper. If the frost is glazed and hard, fill deep pans with hot water and place them on the freezer bottom.

• Close the freezer door/lid. Frost should soften in about fifteen (15) minutes.

Repeat this procedure is necessary.

Care & Cleaning

Cleaning the inside

After defrosting, wash inside surfaces of the freezer with a solution of 2 tbsp. (25 g) of

baking soda in 1 qt. (1 I) warm water. Rinse and dry. Wring excess water out of the sponge or cloth when cleaning in the area of

the controls, or any electrical parts. Wash the removable parts and door basket

with the baking soda solution mentioned above, or mild detergent and warm water. Rinse and dry. Never use metallic scouring pads, brushes, abrasive cleaners, or alkaline

solutions on any surface. Do not wash removable parts in a dishwasher.

Cleaning the Outside

Wash the cabinet with warm water and mild liquid detergent. Rinse well and wipe dry

with a clean soft cloth.

WARNING

if leaving the freezer lid open while on

vacation, make certain that chlldren cannot get into the freezer and become entrapped.

To Defrost Chest Models with Defrost Drain:

Vacation and Moving Tips

Short Vacations: Leave the freezer operating during vacations of less than three weeks.

Long Vacations: If the freezer will not be

used for several months:

" Remove all food and unplug the

power cord.

• Clean and dry the interior thoroughly.

- Leave the freezer door open slightly, blocking it open if necessary, to prevent odor and mold growth.

Moving: When moving the freezer, follow these guidelines to prevent damage:

" Disconnect the power cord plug from the

wall outlet.

* Remove foods, then defrost, and clean

the freezer.

• Secure all loose items such as base panel, baskets, and shelves by taping them securely in place to prevent damage.

" In the moving vehicle, secure freezer in an

upright position to prevent movement. Also protect outside of freezer with a blanket,

or similar item.

* Place a shallow pan or the Divider/Drain

Pan (if equipped) beneath the drain outlet. Pull out the outside drain plug (see figure

1). A 1/2 inch garden hose adapter can be used to drain the freezer directly into a floor drain (see figure 2). If your model is

not equipped with an adapter, one can be purchased at most hardware stores.

* Remove the drain plug inside the freezer

by turning counterclockwise (see figure 3). Defrost water will drain out. Check pan

occasionally so water does not overflow.

* Replace the drain plugs when defrosting

and cleaning are completedJf the drain is left open, warm air may enter the freezer.

To Defrost Models without Defrost Drain:

* Place towels or newspapers on the freezer

bottom to catch the frost. The frost will loosen and fall.

Power/Freezer Failure

NOTE

Do not open freezer door unnecessarily if freezer is off for several hours.

if a power failure occurs, frozen foods will stay frozen for at least 24 hours if the freezer

is kept dosed, if the power failure continues, pack seven or eight pounds of dry ice into the freezer every 24 hours. Look in the Yellow Pages under Dry ice, Dairies, or ice Cream

manufacturers for local dry ice suppliers. Always wear gloves and use caution when handling dry ice.

if the freezer has stopped operating, see "Appliance Does Not Run" in the Troubleshooting Guide. if you cannot solve the problem, call an authorized servicer mediately. If the freezer remains off: for several hours, follow the directions above for the use of dry ice during a

power failure, if necessary, take the food to a local locker plant until the freezer is ready to operate. Look in the Yellow Pages under "Frozen Food Locker Plants".

Before You Call

TROUBLESHOOTING Before calling for service° review this list. It may save you time and

GUIDE expense. This list includes common occurrences that are not the result of

CONCERN POTENTIAL CAUSE COMMON SOLUTION

APPLIANCE OPERATION Appllance does

not run.

defective workmanship or materials in this appliance,

* Appliance is plugged

into a circuit that has a ground fault interrupt.

"Temperature control is

in the OFF position.

* Appliance may not

be plugged in or plug may be loose.

=House fuse blown or

tripped circuit breaker.

° Power outage.

* Use another circuit. If you are unsure about the

outlet_ have it checked by a certified technician.

* See Setting the Temperature Control Section.

* Ensure plug is tightly pushed into outlet,

" Check/replace fuse with a 15=amp time-

delay fuse. Reset circuit breaker.

• Check house lights. Call local electric company.

Before You Call

CONCERN

Appliance runs too

much or too long.

interior temperature is too cold.

interior temperature is too warm.

E×ternal surface tern-

perature is warm.

SOUND AND NOISE

POTENTIAL CAUSE COMMON SOLUTION

* Room or outside

weather is hot.

"Appliance has recently

been disconnected for a period of time.

Large amounts of warm or hot food have been

stored recently. Door is opened too

frequently or too long.

" Door may be

slightly open. Temperature Control is

set too low.

"Gasket isdirty, worn,

cracked, or poorly fitted.

• The unit is in Express Chill mode.

• Temperature Control is set too warm.

Door is kept open too long or isopened

too frequently. Door may not be seating properly.

• Large amounts of warm or hot food may have been stored recently.

• Appliance has recently been disconnected for

a period of time.

" The external walls

can be as much as 30°F warmer than

room temperature.

• it's normal for the appliance to work harder under these conditions.

• It takes 24 hours for the appliance to cool down completely.

• Warm food will cause appliance to run more until the desired temperature is reached.

* Warm air entering the appliance causes it to

run more. Open doors less often. See "DOOR PROBLEMS" in Before You

Call.

" Turn control knob to a warmer setting. Allow

several hours for the temperature to stabilize.

* Clean or change gasket (See "Care and

Cleaning Tips"). Worn, cracked or poorly fitting gaskets should be replaced.

* Exit Express chill mode by entering into

the options menu on the control panel and pressing the "set" button once the indicator is

highlighted next to "Express Chilr'

* Turn control to a colder setting. Allow several

hours for the temperature to stabilize. Warm air enters the appliance every time the

door isopened. Open the door less often.

* See "DOOR PROBLEMS" in Before You Call.

• Wait until the appliance has had a chance to reach its selected temperature.

* Appliance requires 24 hours to cool

down completely.

• This is normal while the compressor works to transfer heat from inside the cabinet.

Louder sound levels

whenever appllance

is on.

Longer sound levels

when compressor

comes on.

Popping or cracking sound when corn-

presser comes on.

Bubbling or gurgling sound, like

water barfing.

* Modern appliances

have increased storage capacity and more

stable temperatures. They require a high

efficiency compressor.

• Appliance operates at higher pressuresduring the start of the ON cycle.

• Metal parts undergo expansion and

contraction, as in hot water pipes.

• Refrigerant (used to cool appliance) is

circulating throughout

the system.

* This is normal. When the surrounding noise

level is low, you might hear the compressor running while it cools the interior.

• This is normal. Sound will level off or disappear as appliance continues to run.

* This is normal.

+ 32 hidden pages

Kenmore 25322742410, 25322442412, 25322442411, 25322442410, 25322042410 Owner’s Manual

Specifications and Main Features

Frequently Asked Questions

User Manual