Kenmore 233.5998892 User Manual
Kenmore
installation instructions
owners manual and repair parts list
Kenmore
GLIDE AWAY
RANGE HOOD
MODEL NUMBER
233.5998892
233.5998811
IMPORTANT Read instructions
carefully for safe installation and
operation
^ SAVE THIS MANUAL FOR
FUTURE REFERENCE
Kenmore. Solid as
Sold by Sears, Roebuck and Co.. Chicago, IL 60684
Cleaning
ALWAYS DISCONNECT ELECTRIC POWER SUPPLY
BEFORE SERVICING HOOD. i>UPPLY
Use a mild detergent suitable for painted surfaces. DO NOT USE
POwmFpl SCOURING
POWDERS. Vacuum blower to clean. Do not immerse blower in
W3t©r.
Wash the foam filter in a mild detergent solution.
io!^c?eaning:^'^®' assembly and light lens are easily removable
See Step 13 on page 4 for removal of glass drawer
assembly. DO NOT clean in a dishwasher.
Remove the light lens by opening the filter panel
(Step 6, page 2) and rotating the 2 metal clips
holding the lens in place.
WARNING
Light Bulb Replacement
Your hood uses a 24" long F20T12 fluorescent tube and an FS’2
starter, which are available at most hardware stores or home
centers.
To check or replace tube: 1) Pull drawer out. 2) Rotate filterpanel
clips and lower filter panel.
If the tube flickers or does not light, check the prongs on the ends
cf the tube to make sure they are properly seated in the tube
nolders.
^ the tube continues to flicker or does not tight, replace the tube.
Slide the tube into the holders and rotate the tube so that the
xongs in the holders grip the tube and hold it in place.
f the ends of the tube light but the center does not, the starter
nay require replacement. The starter is located behind the filter
janel on the right hand side. Install the new starter by pushing
he starter in and turning it clockwise.
f the tube still does not light, order a 99270651 Ballast Trans-
ormer available through Sears stores.
A /I R IN G D I AG R AM
SERVICE PARTS
Kenmore Range Hood * Model 233.5998892 Black
Model 233.5998811 White
KEY
NO.
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
46
48
49
50
"Standard Hardware. May be purchased locally.
"Not Illustrated.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
BLACK
PART NO.
98006940
99150526
9Э090677
99360133
99170245
97006078
98005221
99100379
97008644
97008641
93260454
97011874
97008578
97008618
99160344
99150538
99150537
97008594
99230345
99160319
98005860
99270550
99270651
99270553
97008619
99400042
98006937
98006938
99100463
97008971
97008970
99250932
97009057
99110683
99420508
98007155
99020139
98005212
99100491
99080359
99260476
99420464
97007314
99020138
99140156
99010175
97011138
99050018
99150492
99100408
99150471
97008626
97005965
99041399
WHITE
PART NO.
96007168
99150478
99090697
99360140
99170245
97006078
98005221
99100379
97008981
97008982
93260454
¡97011873
97008578
97008618
99160344
99150638
99150537
97008594
99230342
99160319
98005860
99270550
99270651
99270553
97008619
99400042
98007164
98006938
99100463
97008979
97008978
99250932
97009117
99110699
99420514
98007155
99020139
98005212
99100491
99080359
99260476
99420464
97007314
99020138
99140156
99010175
97011139
99050018
99150492
99100464
99150471
97008628
97005985
99041399
Front Trim
Screw #8-18 X 3/8 (14 Required)'
Conirof Trim
Control Knob
Screw #8-18 X 3/8 (8 Required)'
Damper Assembly (Includes Key Nos
7 & 8)
Damper Flap '
Damper Boshing
RH Mounting Bracket (Includes Key No. 10)
LH Mounting Bracket (Includes Key No. 10)
#8 Sheet Metal Nut “U" Type
(11 Required)
Canopy
Control Board
Control Harness
Screw #8-32 X 3/16 (5 Required)'
Screw #8-18 X 2 (4 Required)'
Screw #8-18 X 1 (4 Required)'
Switch Assembly
Rivet (13 Required)
Screw #6-32 X 3/8 (4 Required)'
Lampholder Bracket (2 Required)
Lampholder (2 Required)
Ballast Transformer
Starter FS-2'
Light Harness
Strain Relief Bushing SR-4N-4 (2 Required)
Access Cover
Wire Box Cover
Drawer Stop (2 Required)
LH Drawer Bracket Assembly (Includes Key
Nos. 32 & 33)
RH Drawer Bracket Assembly (includes
Key Nos. 32 & 33)
Washer (2 Required)*
Drawer Assembly (Includes Key Nos. 14 & 3i)
Drawer End Cap
Thumb Screw (4 Required)
Drawer Clamp (2 Required)
Blower Wheel, Counterclockwise
Motor Retaining Ring (2 Required)
Rubber Motor Mount (4 Required)
Motor
Bfower Mounting Rod Nut (2 Required)
Blower Mounting Rod (2 Required)
Blower Scroll Housing
Blower Wheel, Clockwise
Filter Spring (2 Required)
Filter Foam
Filter Panel
Light Lens
Screw #8-18 X 'A (2 Required)'
Plastic Cap (4 Required)
Screw #10-32 X Vi Green (2 Required)
Green Wire Assembly
Complete Blower Assembly (Includes Key
Nos. 5, 34, 35, 36, 37, 40,'41)
Fluorescent Light Tube F20T12' (Not
Included)
Instruction Book
DESCRIPTION
Loading...