Kenmore 15314076810 Owner’s Manual
Use & Care Guide
®
®
Manual de Uso y Cuidado
Kenmore
Wood Pellet Smoker Grill
Parrilla de ahumar de briquetas de madera
Model/Modelo: 153.14076810
Sears Brands Management Corporation
Hoffman Estates, IL 60179 U.S.A.
www.kenmore.com
Table of Contents
Section Page # Section Page #
Safety Instructions 2 Manual Lighting 14
Hardware Pack 3 Operation Tips & Hazards
Parts List 4 Maintenance 15
Assembly 6 Frequently Asked Questions 17
Initial Firing Procedure 12 Warranty 18
Standard Operation 13 Service Back Cover
14
IMPORTANT SAFETY INSTRUCTIONS
These instructions are for your safety. Read
retain them for future reference.
them
thoroughly before use and
A MAJOR CAUSE OF FIRES IS FAILURE TO MAINTAIN REQUIRED
CLEARANCES (AIR SPACES) TO COMBUSTIBLE MATERIALS. IT IS OF
UTMOST IMPORTANCE THAT THIS PRODUCT BE INSTALLED ONLY IN
ACCORDANCE WITH THESE INSTRUCTIONS.
THIS SMOKER GRILL IS FOR OUTDOOR USE ONLY!
WARNING! Assemble and operate this Grill ONLY according to the instructions in this
Use & Care Guide.
WARNING!
Only use wood pellets sized of .25 inch diameter or less. Do not use wood pellets that are
longer than 1 inch.
NEVER use heating fuel pellets in this grill, due to potential hazardous contaminants and
additives that may be present.
Always store wood pellets in a dry location, away from heat-producing appliances and
other fuel containers.
WARNING!
Hazardous voltage is present which can shock, burn or cause death. Always unplug
the power cord before cleaning or performing other maintenance on this Grill.
Only plug the smoker grill into a receptacle with GFCI (Ground Fault Circuit
Interrupter) protection.
To protect against electrical shock, this appliance is equipped with a power cord having a
3-prong grounding-type plug for insertion into a proper grounding-type receptacle. DO NOT
alter the plug for use in a 2-prong receptacle. If the plug will not fit into a receptacle, have
the proper receptacle installed by a qualified electrician. Do not use an adapter.
If using an extension cord, only insert the plug of this appliance into an extension cord
having a proper grounding-type receptacle. Do not use an adapter.
WARNING!
Never use or store flammable liquids near the Grill.
Never use any flammable liquids such as gasoline, gasoline-type lantern fuel,
kerosene, charcoal lighter fluid, or similar fluids to start or refresh the cooking fire
in the Smoker Grill.
Never use gasoline or lighter fluid to manually light your Grill. Use ONLY Alcohol
Gel for manual lighting, and manually light Grill only according to the instructions
in this Use & Care Guide.
2
CAUTION! Keep the Grill
CAUTION! Do not use
WARNING! The use of this appliance can expose you to chemicals, including
clean. See
accessories
the cleaning Instructions in this Use & Care Guide
not specified for use with this Grill
.
lead, and combustion by-products known to the state of California to cause cancer,
birth defects, or other reproductive harm. Wash your hands after using this appliance!
For more information go to www.P65Warnings.ca.gov
WARNING!
When operating this Grill maintain a MINIMUM distance of 36 inches from all
sides of Grill to any wall or object.
When operating this Grill under overhead surfaces a MINIMUM of 40 inches is
required from top of grill barrel to the surface.
.
Hardware Pack
Item Part Name Qty
A Bolt 5/16” x 2.56” 4
B Bolt 5/16” x 1.77” 4
C Spring Washer OD .33” x ID .51” 18
D Hex Nut 5/16”-18 8
E Washer OD .79” x .33” 16
F Screw 5/32”-32 x 0.2” 2
G Inner Hex Wrench 1
H Washer OD .47”x ID .17” 2
I Screw 1/4”-20 x 0.5” 4
J Washer OD 0.79"x ID 0.26"
K Screw 1/4”-20 x 0.5”
L Hex Nut 1/4”-20 x 0.5”
M Washer OD 0.98” x ID 0.33”
N Cap Nut 5/16”-18
O Hopper Handle
P Screwdriver
Q Wrench
4
15
15
2
2
1
1
2
3
7
Parts List
Kenmore Wood Pellet Smoker Grill 153.14076810
To purchase replacement parts, call 1-844-553-6667
Item Qty Description Part # Item Qty Description Part #
1 1 Grill Barrel Lid Handle ZPG-001A 27 1 Auger Shaft ZPG-027-00
2 1 Name Plate ZPG-002A 28 1 Auger Housing B ZPG-028-00
3 2 Barrel Lid Hinge Assembly ZPG-003A 29 1 Firepot Welding Assembly ZPG-029.00
4 1 Grill Barrel Lid ZPG-004-00 30 1 Hopper Insulation Gasket ZPG-030-00
5 1 Warming Rack ZPG-005A 31 1 Inducer Fan ZPG-DQ-002
6 1 Cooking Grate ZPG-006-00 32 1 Power Cord ZPG-DQ-003
1 Grease Drain Pan ZPG-007.00 33 1
8 1 Smoke Stack Assembly ZPG-008.00 34 1 Right Rear Leg ZPG-032-00
9 1 Heat Baffle ZPG-009-00 35 1 Left Rear Leg ZPG-033-00
10 1 Grill Barrel ZPG-010-00 36 1 Right Front Leg ZPG-034-00
11 1 Heat Sensor Bracket ZPG-011A 37 1 Left Front Leg ZPG-035-00
12 1 Silicone Plug ZPG-012.00 38 1 Bottom Shelf ZPG-036-00
13 1 Side Table Assembly ZPG-013A 39 1 SS Front Panel ZPG-037-00
14 1 Grease Bucket ZPG-014.00 40 1 Axle ZPG-038-00
15 1 Hopper/Burner Assembly ZPG-015-00 41 2 Wheels ZPG-039-00
16 2 Lid Handle Bezel ZPG-016.00 42 2 Cap Nuts ZPG-WJ-01
17 2 Hopper Lid Hinge Assy. ZPG-017-00 43 4 Flat Washer ZPG-WJ-02
18 1 Hopper Lid ZPG-018A 44 2 Spring Washer ZPG-WJ-03
19 1 Hopper Lid Handle ZPG-019-00 45 2 Locking Casters ZPG-040-00
20 1 Hopper Safety Grate ZPG-020-00 46 2 Temperature Probe ZPG-PR07
21 1 Hopper Frame ZPG-021.00 47 3 Tool Hooks ZPG-WJ-04
22 1 Pellet Cleanout Door ZPG-022.00 48 1 Heating Rod ZPG-024.076
23 1 Heat Sensor ZPG-024A 49 1 Fuse ZPG-FU08
24 1 Controller Assembly ZPG-024.00 1 Hardware Pack ZPG-HP05
25 1 Auger Drive Motor ZPG-DQ-001 1 Use & Care Guide ZPG-M06
26 1 Auger Housing A ZPG-026.00
Hopper Bottom
ZPG-031-00
Hopper/Burner Assembly Detail
27
4
Exploded View Kenmore Wood Pellet Smoker Grill 153.14076810
If you are missing hardware or have damaged parts after unpacking Smoker Grill,
call 1-844-553-6667
5
Assembly Step 1: Lid Handle and Hopper Lid Handle
Remove pre-attached washers and screws from Grill Barrel Lid Handle. Use them to attach Lid Handle (1)
to Lid (4) as shown.
Attach Hopper Lid Handle (19) to Hopper Lid (18) with two 5/32″-32 x 0.2″ screws (F) and two washers (H)
as shown.
Assembly Step 2: Legs to Smoker
With the help of an assistant, carefully lay the smoker grill on its back on a non-abrasive surface.
Attach each leg as shown from the smoker grill sides with one 5/16″ x 2.56″ Bolt (A), one Spring Washer (C)
and one Washer (E).
Attach each leg as shown from the smoker grill front and back with one 5/16″ x 1.77″ Bolt (B), one Spring
Washer (C) and one Washer (E).
Note: Each leg will have an identification label as to its correct position for attachment to the smoker.
WARNING! The smoker grill is heavy. To avoid personal injury, obtain the help of an assistance to lay the
unit down and lift it back up.
6
Assembly Step 3: Front Panel to Legs
Position the Front Panel between the front legs as shown. Hand tighten the Front Panel to the legs with two
1/4″-20 x 0.5″ Screws (K) into each leg. Note: Do not fully tighten bolts at this time.
Assembly Step 4: Bottom Shelf to Legs
Position Bottom Shelf between the legs as shown. Hand tighten the Bottom Shelf to legs with two
1/4″-12 x 0.59″ Screws (K) into each leg. Note: Do not fully tighten bolts at this time.
7
Assembly Step 5: Wheels and Casters to Legs
Screw a locking caster into the left front leg and left rear leg. Tighten the casters securely. Slide one wheel
onto the axle then insert the axle through the holes in the right front and rear legs. Slide the remaining wheel
onto the axle and secure each wheel to axle with one spring washer (C), one washer (M), and one 5/16″ cap
nut (N). SET THE SMOKER GRILL UPRIGHT. Note: Fully tighten all bolts at this time.
WARNING! The smoker grill is heavy. To avoid personal injury, obtain the help of an assistant to lay
the unit down and lift it back up.
Assembly Step 6: Side Shelf
Attach side shelf onto the smoker grill barrel
with four 1/4″-20 x 0.5″ Screws (I) and four
washers (J) as shown. Note: Use wrench (Q) to
tighten all screws.
8
Assembly Step 7: Smoke Stack/Smoke Stack Cap
Slide the smoke stack through the hole in the barrel and attach with three 1/4″-12 x 0.59″ Screws (K), three
Hex Nuts (L) and three washers (E), as shown. Then screw the smoke stack cap onto the top of the smoke
stack as shown.
Note: The smoke stack is adjustable to allow more or less smoke to exit the smoker grill. Be careful not to
raise cap too high allowing it to come unscrewed from stack.
Assembly Step 8:
Heat Baffle
Position the Heat Baffle (9) directly over
the firepot on the locating brackets found
on the inside walls of the Grill Barrel. The
notched legs of the baffle should be
facing downward over the locating
brackets.
9
Assembly Step 9:
Grease Drain Pan
Attach the Grease Drain Pan (7) so that
the long flange end hooks over the Grease
Drain Pan support on the right end of the
grill. The short flange end should rest on
the bracket on the left end of the grill as
shown.
Recommendation: For ease of cleanup,
cover the Grease Drain Pan with heavyduty aluminum foil. Be sure edges and
ends of the foil are tight against the
bottom of the Grease Drain Pan.
Assembly Step 10: Cooking Grate/Warming Rack
Lay the Cooking Grate (6) onto the front and back grid supports that run the full length of the
grill barrel cooking chamber as shown.
Attach the warming rack (5) by inserting the four tips into the bracket holes as shown.
10
Assembly Step 11: Grease Bucket
Hang the Grease Bucket (14) onto the Grease Drain Tube located under the right side of the grill barrel
as shown.
Recommendation: For ease of cleanup, cover the interior of Grease Bucket with heavy-duty aluminum foil.
ASSEMBLY OF YOUR SMOKER GRILL IS NOW COMPLETE.
Grasp the Hopper Handle with both hands and tilt Grill back onto its large wheels. Roll the Grill to a
location that is a MINIMUM of 36″ from Grill sides to the nearest wall or object, and a MINIMUM of 40″
from Grill Barrel top to any overhead surface. Plug the Grill into a proper receptacle with GFCI (Ground Fault
Circuit Interrupter) protection.
IMPORTANT! Proceed to the Initial Firing Procedure on page 12 of this Use & Care Guide.
Hopper Handle
11
Loading...