Kenmore 14616133110 Owner’s Manual
Use & Care Guide
Manual de Uso y Cuidado
English / Espafiol
Models/Modelos: 146.16132110/146.16133110
Items / Articulos: 640-02608620-7/640-02608621-5
I(enmore
@ @ @
??ril
P/N 40200139
Sears Brands Management Corporation
Hoffman Estates, IL 60179 U.S.A.
www.kenmore.com
www.sears.com
www.kmart.com
g _ prop_ I°
If you smell gas:
1. Shut off gas to the appliance.
2. Extinguish any open flame.
3. Open lid.
4. If odor continues, keep away from the
appliance and immediately call your gas
supplier or your fire department.
1. Do not store or use gasoline or other
flammable liquids or vapors in the vicinity of
this or any other appliance.
2. An LP cylinder not connected for use shall not
be stored in the vicinity of this or any other
appliance.
Installation Safety Precautions
• Please read this User's Manual in its entirety before using
the grill.
• Failure to follow the provided instruction can result in
seriously bodily injury and/or property damage.
• Some parts of this grill may have sharp edges. Please
wear suitable protective gloves.
• Use grill, as purchased, only with LP (propane) gas and the
regulator/valve assembly supplied.
• Grill installation must conform with local codes, or in their
absence of local codes, with either the National Fuel Gas
Code, ANSI Z223.1/ NFPA 54, Natural Gas and Propane
Installation Code, CSA B149.1, or Propane Storage and
Handling Code, B149.2, or the Standard for Recreational
_/ehicles, ANSI A 119.2/NFPA 1192, and CSA Z240 RV
Series, Recreational Vehicle Code, as applicable.
• All electrical accessories (such as rotisserie) must be
electrically grounded in accordance with local codes, or
National Electrical Code, ANSI / NFPA 70 or Canadian
Electrical Code, CSA C22.1. Keep any electrical cords
and/or fuel supply hoses away from any hot surfaces.
• This grill is safety certified for use in the United States
and/or Canada only. Do not modify for use in any other
location. Modification will result in a safety hazard.
IMPORTANT: This grill is intended for outdoor use only and is
not intended to be installed in or on recreational vehicles or
boats.
Call Grill Service Center For Help And Parts
If you have questions or need assistance during assembly,
please call 1-888-287-0735. You will be speaking to a
representative of the grill manufacturer and not a Sears
employee. To order new parts call Sears at
1-800-4-MY-HOME _.
Product Record
IMPORTANT: Fill out the product record information below.
Model Number
Serial Number
See rating label on grill for serial number.
Date Purchased
NOTE TO INSTALLER: Leave this User's Manual with the
customer after delivery and/or installation.
NOTE TO CONSUMER: Leave this User's Manual in a
convenient place for future reference.
Safety Symbols
The symbols and boxes shown below explain what each heading
means. Read and follow all of the messages found throughout
the manual.
DANGER: Indicates an imminently hazardous situation
which, if not avoided, will result in death or serious injury.
WARNING: Indicates an potentially hazardous situation
which, if not avoided, could result in death or serious injury.
CAUTION
For residential use only. Do not use for commercial
cooking.
2 ° 16132-40200139
_;2012 KCD IP,LLC
CAUTION
CAUTION: Indicates a potentially hazardous situation or
unsafe practice which, if not avoided, may result in minor or
moderate injury.
For Your Safety ...
Grill Service Center...
Product Record Information ...
Installation Safety Precautions ...
Safety Symbols ...
Kenmore Grill Warranty...
Use and Care.
Parts List...
Parts Diagram...
Before Assembly ...
... 13-16
Assembly...
Troubleshooting...
Repair Protection Agreements
Congratulations on making a smart purchase. Your new I(enmore _)
product is designed and manufactured for years of dependable
operation. But Iike alI products, it may require repair from time to time
That's when having a Repair Protection Agreement can save you
money and aggravation.
Purchase a Repair Pro/ec/ion Agreement now and pro/ec/ yourse/f
from unexpected hassle and expense.
Here's what the Repair Protection Agreement s includes:
2
2
2
2
2
3
•.. 4-10
...11
• .12
• 17-22
• 23-25
KENMORE GRILL WARRANTY
One Year Full Warranty on Kenmore Grill
Ifthis griii fails due to a defect in materiai or workmanship
within one year from the date of purchase, catt 1-800-4-MY
HOME @to arrange for free repair (or replacement if repair
proves impossible).
Limited Warranty on Burners
For ten years from the date of purchase, any burner that
rusts through will be replaced free of charge. After the first
year from the date of purchase, you pay for labor if you wish
to have it installed.
Aii warranty coverage exciudes ignitor batteries and grill part
paint toss, discoloration or rusting, which are either
expendable parts that can wear out from normal use within
the warranty period, or are conditions that can be the result
of normal use, accident or improper maintenance.
Aii warranty coverage isvoid if this griit is ever used for
commercial or rental purposes.
Aii warranty coverage applies only if this grill is used in the
United States.
[] Expert service by our 10,000 professional repair specialists
[] Unlimited service and no charge for parts and labor on alI
covered repairs
[] Product replacement up to $1500 if your covered product
can't be fixed
[] Discount of 25% from regular price of service and related
installed parts not covered by the agreement; also, 25% off
regular price of preventive maintenance check
[] Fast help by phone - we catI it Rapid Resolution -
phone support from a Sears representative. Think of us
as a "talking owner's manual."
Once you purchase the Repair Protection Agreement, a simple phone
catt is att that it takes for you to schedule service. You can calI
anytime day or night, or schedule a service appointment online.
The Repair Protection Agreement is a risk-free purchase. If you
cancel for any reason during the product warranty period, we wilt
provide a fulI refund. Or, a prorated refund anytime after the
product warranty period expires. Purchase your Repair
Protection Agreement today!
Some limitations and exclusions apply. For prices and
additional information in the U.S.A.call 1-800-827-6655.
This warranty gives you specific legal rights, and you may
atso have other rights which vary from state to state.
SearsBrandsManagement Corporation
Hoffman Estates,IL60179
Sears Installation Service
For Sears professional installation of home appliances, garage
door openers, water heaters, and other major home items, in the
U.S.A. cait 1-800-4-MY-HOME _
*Coverage inCanada varies on someitems.Forfull details
call SearsCanada at 1-800-361-6665.
16132-40200139 ° 3
° NEVER store a spare LP cylinder under or near the
appliance or in an enclosed area.
° Never fill a cylinder beyond 80% full.
• If the information inthe two points above is not
followed exactly, a fire causing death or serious
injury may occur.
• An overfilled or improperly stored cylinder isa
hazard due to possible gas release from the safety
relief valve. This could cause an intense fire with
risk of property damage, serious injury or death.
• If you see, smell or hear gas escaping,
immediately get away from the LP cylinder and
appliance and call your fire department.
LPTank Removal, Transport And Storage
• TurnOFFatI control knobsand LPtank valve. Turncoupling nut
counterclockwise by hand only- do not usetools to
disconnect.LiftLPtankwire upward off of LPtankcollar, then Iift
LPtank up and off of support bracket. Installsafetycap onto LP
tank valve.Always use cap and strap suppliedwith valve.
Failure to use safety cap as directed may result in serious
personal injury and/or property damage.
LPTank Valve._, f_ \
_Safety Cap
"_/-_ i Retainer Strap
• A disconnected LPtank in storage or being transported must
have a safety cap installed (as shown). Do not store an LPtank
in enclosed spaces such as a carport, garage, porch, covered
patio or other building. Never leave an LPtank inside a vehicle
which may become overheated by the sun.
• Do not store an LPtank in an area where children play.
LP Cylinder
• The LPcylinder used with your grill must meet the following
requirements:
• Use LPcylinders only with these required measurements: 12"
(30.5cm) (diameter) x 18" (45.7 cm) (tail) with 20 lb. (9 kg.)
Capacity maximum.
• LPcylinders must be constructed and marked in accordance
with specifications for LPcylinders of the U.S. Department of
Transportation (DOT) or for Canada, CAN/CSA-B339,
cylinders, spheres and tubes for transportation of dangerous
goods. Transport Canada (TC). See LPcylinder colIar for
marking.
• LPcylinder valve must have:
• Type 1 outlet compatible with
regulator or grill.
• Safety relief valve.
• UL listed Overfilt Protection
Device (OPD). This OPD safety OPDHand Wheel
feature is identified by a unique triangular hand wheel. Use
only LP cylinders equipped with this type of valve.
• LPcylinder must be arranged for vapor withdrawal and
include collar to protect LPcylinder valve. Always keep LP
cylinders in upright position during use, transit or storage.
LPcylinder in upright position for vapor withdrawal
LP (Liquefied Petroleum Gas)
• LPgas is nontoxic, odorless and colorless when produced. For
Your Safety, LPgas has been given an odor (similar to rotten
cabbage) so that it can be smelled.
• LPgas is highly flammable and may ignite unexpectedly when
mixed with air.
LP Cylinder Filling
• Use only licensed and experienced dealers.
• LPdealer must purge new cylinder before filling.
• Dealer should NEVER tilt LPcylinder more than 80% of LP
cylinder volume. Volume of propane in cylinder wilt vary by
temperature.
• A frosty regulator indicates gas overfill. Immediately close LP
cylinder valve and caII local LPgas dealer for assistance.
• Do not release liquid propane (LP)gas into the atmosphere. This
isa hazardous practice.
• To remove gas from LPcylinder, contact an LPdealer or catt a
local fire department for assistance. Check the telephone
directory under "Gas Companies" for nearest certified LP
dealers.
4 ° 16132-40200139
LP Tank Exchange Connecting Regulator To The LP Tank
• Many retailers that seii griiis offer you the option of replacing
your empty LPtank through an exchange service. Use only those
reputable exchange companies that inspect, precision fill, test
and certify their cylinders. Exchange your tank only for an OPD
safety feature-equipped tank as described in the "LPTank"
section of this manual.
• Always keep new and exchanged LPtanks in upright position
during use, transit or storage.
• Leak test new and exchanged LPtanks BEFOREconnecting to
grill.
LP Tank Leak Test
For your safety
• Leak test must be repeated each time LPtank is exchanged or
refilled.
• Do not smoke during Ieak test.
• Do not use an open flame to check for gas leaks.
• Grill must be Ieak tested outdoors in a welI-ventilated area,
away from ignition sources such as gas fired or electrical
appliances. During teak test, keep grill away from open flames
or sparks.
• Use a clean paintbrush and a 50/50 mild soap and water
solution. Brush soapy solution onto areas indicated by arrows
in figure below. Leaksare indicated by growing bubbles.
1.LPtank must be properly secured onto grill. (Refer to
assembly section.)
2. Turn aII control knobs to the OFF position.
3. Turn LPtank OFF by turning OPD hand wheel clockwise to a
fulI stop.
4. Remove the protective cap from LPtank valve. Always use
cap and strap supplied with valve.
Hand Wheel
rpe 1 outlet with
thread on outside
Safety Relief
/
Strap and Cap
If "growing" bubbles appear do not use or move the LP
tank. Contact an LPgas supplier or your fire department!
• Do not use household cleaning agents. Damage to the gas
train components (vatve/hose/regulator) can result.
Do not insert a POL transport plug
(plastic part with external
threads) into the type 1 valve
outlet. It will defeat the Safety
Relief Valve feature.
5. Hold regulator and insert nipple into LP
tank valve. Hand-tighten the coupling
nut, holding regulator in a straight Iine
with LPtank valve so as not to crossth-
thread the connection.
Nipple has to be
centered into the LP
tank val
16132-40200139 ° 5
Hold coupling nut and regulator
as shown for proper connection
to LP tank valve.
6. Turn the coupling nut clockwise and tighten to a fuII stop. The
regulator wiII seat on the back-check feature in the LPtank
valve, resulting in some resistance. An additional one-half to
three-quarters turn is required to complete the connection.
Tighten by hand only - do not use tools.
NOTE"
If you cannot complete the connection, disconnect regulator
and repeat steps 5 and 6. If you are still unable to complete the
connection, do not use this regulator!
Catt 1-800-4-MY-HOME ® for an identical replacement part.
Leak Testing Valves, Hose and Regulator
1.Turnall grill control knobsto OFF.
2.Be sure regulator is tightly connected to LPtank.
3.Compieteiy open LP tank valve by turning OPD hand wheel
counterclockwise. If you hear a rushing sound, turn gas off
immediately. There is a major Ieak at the connection. Correct
before proceeding by calling Sears for replacement parts at
1-800-4-MY-HOME _.
4.Brush soapy solution onto areas where bubbles are shown in
picture below:
• Never remove threaded
orifice at end of valve.
• Do not insert any tool or foreign object into the valve
outlet or safety relief valve. You may damage the valve
and cause a leak. Leaking propane may result in
explosion, fire, severe personal injury, or death.
• Outdoor gas appliance is not intended to be installed
in or on a boat.
• Outdoor gas appliance is not intended to be installed
in or on an RV.
• Never attempt to attach this grill to the self-contained
LPgas system of a camper trailer or motor home.
• Do not usegrill until leak-tested.
• If a leak is detected at any time, STOP and call the fire
department.
• If you cannot stop a gas leak, immediately close
LPcylinder valve and call LPgas supplier or your fire
department!
5. If "growing" bubbles appear, there is a leak. Close LPtank
valve immediately and retighten connections. If leaks cannot be
stopped do not try to repair. Catt Sears for replacement
parts at 1-800-4-MY-HOME ®.
6. Aiways ciose LPtank valve after performing teak test by
turning hand wheel clockwise.
6 ° 16132-40200139
For Safe Use of Your Grill and to Avoid Serious
Injury.
• Do not let children operate or play near grill.
• Keep grill area clear and free from materials that
burn.
• Do not block holes in sides or back of grill.
• Use grill only in well-ventilated space. NEVER use
in enclosed space such as carport, garage, porch,
covered patio, or under an overhead structure of
any kind.
• Do not use charcoal or ceramic briquets in a gas
grill, fUn/ess briquets are supp/ied with your grilI.J
• Use grill at least 3 ft. from any wall or surface.
Maintain 10 ft. clearance to objects that can catch
fire or sources of ignition such as pilot lights on
water heaters, live electrical appliances, etc.
Safety Tips
• Before opening LPcylinder valve, check the coupling nut for
tightness.
• When grill is not in use,turn off all control knobs and LPcylinder
valve.
• Never move grill while in operation or stili hot.
• Use long-handled barbecue utensils and oven mitts to avoid burns
and splatters.
• Maximum load for sideburner and side shelf is 10 tbs.
• The grease tray must be inserted into grill and emptied after each
use. Do not remove grease tray until grill has completely cooled.
• Clean grill often, preferably after each cookout. If a bristle brush is
used to clean any of the griii cooking surfaces, ensure no loose
bristles remain on cooking surfaces prior to grilling. It is not
recommended to clean cooking surfaces while grill is hot.
• Ifyou notice grease or other hot material dripping from grill
Determine the cause, correct it, then clean and inspect valve,
Keep ventilation openings in cylinder enclosure (grill cart) free
and clear of debris.
• Do not store objects or materials inside the grill cart enclosure that
would block the flow of combustion air to the underside of either
the control panel or the firebox bowl.
• The regulator may make a humming or whistling noise during
operation. This will not affect safety or use of grill.
• If you have a grill problem see the "Troubleshooting Section".
• If the regulator frosts, turn off grill and LP cylinder valve
immediately. This indicates a problem with the cylinder and it
should not be used on any product. Return to supplier!
• Apartment Dwellers.
Check with management to learn the requirements
and fire codes for using an LP gas grill in your
apartment complex. If allowed, use outside on the
ground floor with a three (3) foot clearance from
walls or rails. Do not use on or under balconies.
• NEVER attempt to light burner with lid closed. A
buildup of non-ignited gas inside a closed grill is
hazardous.
• Never operate grill with LP cylinder out of correct
position specified in assembly instructions.
• Always close LP cylinder valve and remove
coupling nut before moving LP cylinder from
specified operation position.
CAUTION
• Putting out grease fires by closing the lid is not possible.
Grills are well ventilated for safety reasons.
• Do not use water on a grease fire. Personal injury may
result. If a grease fire develops, turn knobs and LP
cylinder off.
• Do not leave grill unattended while preheating or burning
off food residue on HI. If grill has not been regularly
cleaned, a grease fire can occur that may damage the
product.
Burner Ignitor Lighting
• Pleaserefer to the lighting procedure on grill.
Main Burner Match Lighting
• Do not lean over grill while lighting.
1.Open lid during lighting.
2. Place match into match holder (hanging from side of cart).
Light match, place into lighting hole on left side of firebox.
3. Turn right knob to Hi position. Be sure burner lights and stay
lit.
4. Light other burners follow with steps 3.
16132-40200139 ° 7
Turn controls and gas source or tank OFF when not
in use.
CAUTION
Burner Flame Check
• Removecooking grates and flame tamers. Lightburners,rotate
knobsfrom HIGH to LOW. You shouldsee asmallerflamein
LOW position than seenon HIGH. Performburner flame check
on sideburner,also.Always check flame prior to each use.If
only tow flame is seenrefer to "Suddendrop or Iow flame" in
the Troubleshooting_Section.
HIGH
If ignition does NOT occur in 5 seconds, turn the
burner controls OFF, wait 5 minutes and repeat the
lighting procedure. If the burner does not ignite with
The valve open, gas will contiune to flow out of the
burner and could accidently ignite with risk of injury
Searing Burner Match Lighting
].Open lid for side burner during lighting.
2.Turn on valve from source or tank.
3.Pushand turn Searing Burner control knob to HI.
4.If ignition does NOT occur in 5 seconds, turn Searing Burner
control knob OFF, wait 5 minutes, and repeat the lighting
instructions.
Sideburner Match Lighting
1.Open sideburner lid. Turn on gas at LPcylinder.
12.PtaceIit match near burner.
3.Turn sideburner knob to Hi. Be sure burner lights and stays tit.
LOW
Turning Grill Off
• Turn att knobs to OFF position. Turn LPcylinder off by turning
Ignitor Check
• Turn gas off at LPcylinder. Press and hold electronic ignitor
button. "Click" should be heard and spark seen each time
between collector box or burner and electrode. See
"Troubleshooting" if no click or spark.
Valve Check
• Important: Make sure gas is off at LPcylinder before
checking valves. Knobs tock in OFF position. To check
valves, first push in knobs and release, knobs should spring
back. If knobs do not spring back, replace valve assembly
before using grill. Turn knobs to LOW position then turn back to
OFF position. Valves should turn smoothly.
Hose Check
• Before each use, check to see if hoses are cut or worn.
Replace damaged hoses before using grill. Use onty
vatve/hose/regulator as specified in the parts tist of this Use & Care
Guide.
General Grill Cleaning
• Do not mistake brown or black accumulation of grease and
smoke for paint. Interiors of gas grills are not painted at the
factory (and should never be painted). Apply a strong solution
of detergent and water or use a grill cleaner with scrub brush
on insides of grill lid and bottom. Rinse and allow to completely
air dry. Do not apply a caustic grill/oven cleaner to painted
surfaces.
• Porcelain surfaces: Because of glass-like composition, most
residue can be wiped away with baking soda/water solution or
specially formulated cleaner. Use nonabrasive scouring powder
for stubborn stains.
• Painted surfaces: Wash with mild detergent or nonabrasive
cleaner and warm soapy water. Wipe dry with a soft
n.onabrasive cloth.
• Stainless steel surfaces: To maintain your grill's high quality
appearance, wash with mild detergent and warm soapy water
and wipe dry with a soft cloth after each use. Baked-on grease
deposits may require the use of an abrasive plastic cleaning
pad. Use only in direction of brushed finish to avoid damage.
Do not use abrasive pad on areas with graphics.
• Cooking surfaces: If a bristle brush is used to clean any of
the grill cooking surfaces, ensure no loose bristles remain on
cooking surfaces prior to grilJing. It is not recommended to
clean cooking surfaces while grill is hot.
8 ° 16132-40200139
CAUTION
SPIDER ALERT!
IMPORTANT: Always ensure that the venturi burner tubes
are clean. A venturi burner tube has a narrow area in
which spiders tend to build nests.
If you notice that your grill isgetting hard to light or that the
flame isn't as strong as it should be, take the time to check and
clean the venturi's.
Spiders or small insects have been known to create "flashback"
problems. The spiders spin webs, build nests and lay eggs in the grill's
venturi tube (s) obstructing the flow of gas to the burner. The
backed-up gas can ignite in the venturi behind the control panel. This
is known as a flashback and it can damage your grill and even cause
injury.
To prevent flashbacks and ensure good performance the burner and
venturi assembly should be removed from the grill and cleaned
•before use whenever the grill has been idle for an extended period.
Cleaning the Burner Assembly
Follow these instructions to clean and/or replace parts of burner
assembiy or if you have froubie igniting griii.
1. Turn gas off at control knobs and LPcylinder
2. Remove cooking grates and heat diffusers.
3. Remove screws and carryover tubes from rear of burners.
4. Remove screw to disengage burner from bracket on
firebox.
5. Carefully tiff each burner up and away from valve openings.
We suggest three ways to clean the burner tubes. Use the one
easiest for you.
(A) Bend a stiff wire (a light weight coat hanger works well)
into a small hook Runthe hook through each burner
tube several times
(B) Use a narrow bottle brush with a flexible handle (do not
use a brass wire brush), run the brush through each
burner tube several times
(C) Wear eye protection: Use an air hose to force air into
the burner tube and out the burner ports Check each
port to make sure air comes out each hole
6 Wire brush entire outer surface of burner to remove
food residue and dirt
7 Clean any blocked ports with a stiff wire such as an
open paper clip
8 Check burner for damage, due to normal wear and
corrosion some holes may become enlarged If any large
cracks or holes are found replace burner
VERY IMPORTANT: Burner tubes must reengage valve
openings. See illustrations below.
9 Carefully replace burners
10 Attach burners to brackets on firebox
11 Reposifion carryover tubes and attach to burners Replace
heat diffusers and cooking grates
Storing Your Grill
•Clean cooking grates
•Store in dry location
•When LPcylinder is connected to grill, store outdoors in a
weiiventiiated space and out of reach of children
•Cover grill if stored outdoors Choose from a variety of grill
covers offered by manufacturer once available
•Store grill indoors ONLY if LPcylinder is turned off and
Disconnected, remove from grill and stored outdoors
• When removing grill from storage, follow "Cleaning the Burner
Assembly' instructions before starting grill
16132-40200139 ° 9
Indirect Cooking
Poultry and large cuts of meat cook slowly to perfection on the grill
by indirect heat. Place food over unlit burner(s); the heat from tit
burners circulates gently throughout the grill, cooking meat or
poultry without the touch of a direct flame. This method greatly
reduces flare-ups when cooking extra fatty cuts because there is no
direct flame to ignite the fats and juices that drip during cooking.
1 Burner Cooking
Cook with direct or indirect heat.
Best for smaller meals or foods.
Consumes less fuel.
Indirect Cooking Instructions
• Always cook with the Iid closed.
• Due to weather conditions, cooking times may vary. During
cotd and windy conditions the temperature setting may
need to be increased to insure sufficient cooking
temperature.
• Place food over over unlit burner(s).
Food Safety
Food safety is a very important part of enjoying the outdoor
cooking experience. To keep food safe from harmful bacteria,
foilow these four basic steps:
Clean: Wash hands, utensils, and surfaces with hot soapy water
before and after handling raw meat and poultry.
Separate: Separate raw meats and poultry from ready-to-eat
foods to avoid cross contamination. Use a clean platter and
utensils when removing cooked foods.
Cook: Cook meat and poultry thoroughly to kilt bacteria. Use a
thermometer to ensure proper internal food temperatures.
Chill: Refrigerate prepared foods and leftovers promptly. For
more information call: USDA Meat and Poultry Hotline at
1-800-535-4555 (In Washington, DC (202) 720-3333, 10:00 am
4:00 pm EST).
How To Tell If Meat Is Grilled Thoroughly
• Meat and poultry cooked on a grill often browns very fast
on the outside. Use a meat thermometer to be sure food has
reached a safe internal temperature, and cut into food to
check for visual signs of doneness.
• Whole poultry should reach 180° F; breasts, 170° F.Juices
should run clear and flesh should not be pink.
• Hamburgers made of any ground meat or poultry should
reach 160° F,and be brown in the middle with no pink juices
Beef, veal and tamb steaks, roasts and chops can be
cooked to 145° F.Aii cuts of pork should reach 160° F.
• NEVER partially grill meat or poultry and finish cooking
later. Cook food completely to destroy harmful bacteria.
• When reheating takeout foods or fully cooked meats tike
hot dogs, grill to 165° F,or until steaming hot.
2 Burner Cooking
Great indirect cooking on low.
Produces slow, even heating.
Ideal for slow roasting and baking.
WARNING: To ensure that it is safe to eat, food must be cooked
to the minimum internal temperatures listed in the table below.
USDA* Recommended Safe Minimum Internal Temperatures
Beef, VeaI, Lamb and Pork - Whole Cuts _ 145° F
Fish 145° F
Beef, Veal, Lamb and Pork - Ground 160° F
Egg Dishes 160° F
Turkey, Chicken & Duck - Whole, Pieces & 160°F
Ground
United States Department of Agriculture
_Altow meat to rest three minutes before carving or consuming.
10 ° 16132-40200139
Key
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
2O
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
Description
Sideburner Lid
Rotate Rod, Sideburner Lid
Sideburner Grid
Sideburner
Ignitor Wire, Sideburner
Sideburner Base
RightSide Shelf
Fascia, RightSide Shelf
Electronic Ignition Module
Control Panel
Impulse Control Line
Gas Valve, Main Burner
Gas Valve, Searing Burner
Gas Valve, Sideburner
Manifold, Sideburner
Sideburner Hose
Manifold, Main Burner
Bezel, Control Knob
Control Knob
Regulator
Hole Bushing
RightSide Panel
Top Door Pin
Right Door
Door Handle
Left Door
Bottom Shelf
Lower Door Magnet
Caster With Brake
Caster
Tank Holder
Cotter Pin
Tank Baffle
Left Side Panel
Match Holder
Qty Part Number
1 40200044
2 40800118
1 40800119
1 40800120
1 40800121
1 40800063
1 40200035
1 40200039
1 40200089
1 40200015
1 40200090
3 40200081
1 40200082
1 40200088
1 40200045
1 40800113
1 40200021
5 40800034
5 40800113
1 40800115
1 40400005
1 40200050
2 40200093
1 40200062
2 40200091
1 40200058
1 40200065
1 40200072
2 40200095
2 40200096
1 40800085
4 40800130
1 40200070
1 40200048
1 40800128
Key Description
36 Mater Holder Bracket
37 Back Panel
38 Door Bracket
39 Right Door Pin Bracket
40 Left Door PinBracket
41 Top Door Magnet
42 Back Rail
43 Grease Cup
44 Grease Cup Clip
45 Grease Accumulate Panel
46 Fascia, Left Side Shelf
47 Hook
48 PushBar
49 Left Side Shelf
50 Silicone Rubber Bumper
51 Temperature Gauge
52 Bezel, Temperature Gauge
53 Logo Plate
54 Rotate Rod, Lid
55 Lid
56 Warming Rack
57 Cooking Grate
58 Back Bracket, Searing Burner
59 Front Bracket, Searing Burner
60 Right Heat Diffuser
61 Heat Diffuser
62 Gas Hose Shield
63 Firebox
64 Bracket, Control Panel
65 No.1 Ignitor Wire, Main Burner
66 No.2 Ignitor Wire, Main Burner
67 No.3 Ignitor Wire, Main Burner
68 Electrode, Searing Burner
69 Searing Burner
70 Main Burner
Qty Part Number
1 40800129
1 40200052
1 40200055
1 40200057
1 40200056
1 40200094
1 40200053
1 40800026
1 40800131
1 40400002
1 40200030
4 40800123
1 40800099
1 40200024
4 40800107
1 40800104
1 40800105
1 40800106
2 40800108
1 40200128
1 40400003
3 40400004
1 40200013
1 40200012
1 40200011
2 40800023
1 40200019
1 40200006
2 40200020
1 40200086
1 40200085
1 40200084
1 40200087
1 40200078
3 40200077
Not Pictured
Hardware Pack
Manual
1 40200140
40200139
If you are missing hardware or have
damaged parts after unpacking grill,
call 1-888-287-0735 for replacement.
To order replacement parts after usinggrill,
call 1-800-4-MY-HOME ®
16132-40200139 ° 11
._........................................................_.............................,. %\\ ....... ___...................................._ _. -.,,..
_))-..........................................................=. -................... fi-:
-.. #-] #................._........................,_
............ --"t C)
12 o 16132-4200139
READ AND FOLLOW THE INSTRUCTIONS BELOW TO CORRECTLY UNPACK GRILL PARTS FROM
SHIPPING BOX.
Step 1. Once you open the top of the shipping box, slice down its four edges with a box cutter.
Take out the Hardware Pack, two grill side panels, back panel and bottom shelf. Next remove the
door bracket, back rail and warming rack. Note; Doors are packed inside left & right side panels,
remove doors from left and right panels by depressing the door pin and sliding it out (see below
figures), please do not remove the Styrofoam until Step 2. Remove all parts from plastic bags.
Side panel & door
Depress door pin & slide door out
16132-40200139 * 13
Step 2. With the aid of an assistant, turn grill head over on its side as shown in the first figure below, and
remove the top styrofoam piece. Lay the styrofoam piece flat on the floor. With the aid of an assistant,
lift the grill head out of the bottom styrofoam piece. Place the grill upright on the other styrofoam piece
as shown in the second figure below.
CAUTION. DO NOT place the grill head directly on the floor or the grease tray could become bent.
14 * 16132-40200139
Step 3; Open grill lid, and take out the small boxes packed within the grill head. Remove all packing
materials, and remove all parts from boxes as shown in the figures below.
16132-40200139 * 15
CAREFULLY READ AND PERFORM ALL ASSEMBLY iNSTRUCTiONS ON THE FOLLOWING PAGES.
Tools Required:
• Adjustable wrench (not provided)
• Screwdriver (not provided)
• 7/16" Combination wrench (not provided)
• The following hardware is provided in a blister pack for convenient use.
M4XIO screw
Qty: 20 pcs
M5X10 screw
Qty: 4 pcs
M6X13 screw
Qty: 16pcs
AA Battery
Qty:l pc
M5 flat washer
Qty: 4 pcs
M6X15 screw
Qty: 16pcs
M5 lock washer
Qty: 4 pcs
M6 flat washer(Dia 16)
Qty: 8 pcs
M6 flat washer(Dia 12)
Qty: 16pcs
16 * 16132-40200139
M6 compression washer
Qty: 8 pcs
@
M6 lock washer
Qty: 24 pcs
[] Turn bottom shelf upside down. Attach the wheels to bottom shelf with (16) M6x15 screws, M6
D Bottom Shelf
M6X15 screw Qty: 16pcs
lock washers and M6 flat washers(Dia 12). Note: The casters with brakes should be mounted
on the side with cutout holes.
[] Turn bottom shelf right side up. Attach door magnets to bottom shelf with (2) M4xl0 screws.
M6 lock washer
M6 flat washer(Dia 12)Qty: 16pcs
Qty: 16pcs
t,,,,,
M4XIO screw Qty: 2 pcs
\
i_
.jj.J'_
16132-40200139 _ 17
Loading...