Kenmore 141.17228, 141.16228 Owner's Manual

Owner's Manual

Liquid Propane Gas Grill

Model141.16228

Natural Gas Grill

Model141.17228

A WARNING:

Read this Owner's Manual carefully and be sure your gas grill is properly assembled, installed and

maintained. Failure to follow these instructions could result in serious bodily injury and/or property

damage. This gas grill is intended for outdoor use only and is not intended to be installed in or on

recreational vehicles or boats.

Note to Installer: Leave this Owner's Manual

with the consumer after delivery and/or installation.

Note to Consumer: Leave this Owner's Manual

in aconvenient place for future reference.

Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.

P80102001B * Date:2004/01/20

Warranty ..................................................... 2

Safety Instructions ..................................... 2

Hardware .................................................... 6

Parts Diagram and Lists ...................... 10

Assembly Instructions .............................. 13

Lighting Instructions ................................ 24

Cleaning and Maintenance Instructions .... 26

Frequently Asked Questions .................. 28

Cooking Instructions .............................. A-1

Cooking Guide and Recipes .............. A-2

Full 1-Year Warranty on Grill

For one year from the date of purchase Sears will repair or replace, at our option, any grill part

(except for paint loss, rusting and ignitor battery) that is defective in material or workmanship.

Limited Warranty on Selected Grill Parts

From one year after the date of purchase for the designated time periods listed below, Sears will

replace the following grill parts if they are defective in material or workmanship. You will be charged for labor.

• 1 Year: Cast Iron Burners

• 2 Years: All Other Grill Parts (except flame tamers, cooking grids and ignitor battery)

Warranty Service Warranty service is available by contacting the

nearest Sears Service Center at 1-800-4-MY-HOME ®

Warranty Restrictions

• This warranty is void if grill is used for com-

mercial or rental purposes.

• This warranty applies only when the grill is

used in the United States.

• This warranty gives you specific legal rights,

and you may also have other rights which vary

from state to state.

Sears, Roebuck and Co., Dept. 817WA,

Hoffman Estates, IL 60179

Z_WARNING

Combustion byproducts produced when using this product contain chemicals known to the

State of California to cause cancer, birth defects, or other reproductive harm.

/_kWARNING

Failure to comply with these instructions could result in a fire or explosion that could cause serious bodily injury, death, or

property damage.

AkWARNING

Your grill will get very hot. Never lean over

the cooking area while using your grill. Do not

touch cooking surfaces, grill housing, Lid or any

other grill parts while the grill is in operation, or until the grill has cooled down after use.

Failure to comply with these instructions may result in serious bodily injury.

AkWARNING

(a) Do not store a spare LP-gas cylinder under or near this appliance; (b) Never fill the cylinder beyond 80 percent full; and (c) If the information in "(a)" and "(b)" is not

followed exactly, a fire causing death or serious injury may occur.

FOR YOUR SAFETY

1. Do not store or use gasoline or other flam-

mable material and liquids in the vicinity of this

or any other appliance.

2. ALP cylinder not connected for use must not be stored in the vicinity of this or any other

appliance.

FOR YOUR SAFETY

If you smell gas:

1.Shut off gas to the appliance.

2. Extinguish any open flame such as candle,

cigarette, lighter, etc., that could cause gas to ignite.

3. Open the Grill Lid.

4. If odor continues, immediately call your gas

supplier or your fire department.

IMPORTANT: Your Kenmore LP Gas Grill cannot be converted to use Natural Gas. Attempting to do

so is extremely hazardous and will also void the grill warranty.

Grill Installation Codes The installation must conform with local codes or, in

the absence of local codes, with either the National Fuel Gas Cede, ANSI Z223.1/NFPA 54, or CAN/ CGA-B149.1, Natural Gas and Propane Installation

Code.

2 © Sears, Roebuck and Co.

Correct LP Gas Tank Use

LP gas grill models are designed for use with a standard 20 lb. Liquid Propane Gas (LP gas) tank, not included in grill box. Never connect your gas _ritl to an LP gas tank that exceeds this capacity.

tank of approximately 12 inches in diameter by

18-1/2 inches high is the maximum size LP gas

tank to use. You must use an "OPD" gas tank

which offers a listed Overfill Prevention Device. This safety feature prevents tank from being overfltled

which can cause malfunction of LP gas tank,

regulator and/or grill. The LP gas tank must be constructed and marked

in accordance with the Specifications for LP-Gas Cylinders of the U.S. Department of Transportation

(D.O.T.) or the National Standard of Canada, CAN/ CSA-B339, Cylinders, Spheres and Tubes for Trans-

portation of Dangerous Goods; and Commission, as applicable.

1. The LP gas tank has a shutoff valve, termi- nating in an LP gas supply tank valve outlet, that is compatible with a Type 1 tank con- nection device. The LP gas tank must also have a safety relief device that has a direct connection with the vapor space of the tank.

2. The tank supply system must be arranged for vapor withdrawal.

3. The LP gas tank used must have a collar to protect the tank valve.

• LP gas tanks must be stored outdoors in a well-ventilated area and out of the reach of

children. Disconnected LP gas tanks must not be stored in a building, garage or any other

enclosed area.

• When your gas grill is not in use the gas must be turned off at the LP gas tank.

• The regulator and hose assembly can be seen after opening the doors (if applicable), must be inspected before each use of the grill. If there

is excessive abrasion or wear or if the hose is cut, it must be replaced prior to the grill being

used again.

• Keep the gas regulator hose away from hot grill surfaces and dripping grease. Avoid unnec- essary twisting of hose. Visually inspect hose prior to each use for cuts, cracks, excessive wear or other damage. If the hose appears damaged do not use the gas grill. Call Sears

at 1-800-4-MY-HOME ® (1-800-469-4663) for a Sears authorized replacement hose.

• Never light your gas grill with the lid closed or before checking to ensure the burner tubes are fully seated over the gas valve orifices.

• Never allow children to operate your grill. Do not allow children to play near your grill.

Proper Placement and Clearance of Grill Never use your gas grill in a garage, porch, shed,

breezeway or any other enclosed area. Your gas grill is to be used outdoors only, at least 24 inches from the

back and side of any combustible surface. Do not locate this appliance underoverhead unprotected

combustible surfaces. Do not obstruct the flow of ventilation air around the gasgrill housing.

This outdoor gas grill is not intended to be installed in or on recreational vehicles and/or boats.

• Never connect an unregulated LP gas tank to your gas grill. The gas regulator assembly supplied with your gas grill is adjusted to have an outlet pressure of 11" water column (W.C.) for connection to an LP gas tank.

• Only use the regulator and hose assembly supplied with your gas grill. Replacement regulators and hose assemblies must be those specified by Sears.

• Have your LP gas tank filled by a reputable propane gas dealer and visually inspected and re-qualified at each filling.

• Never fill the gas tank beyond 80% full.

Have your propane gas dealer check the

release valve after every filling to ensure that it remains free of defects.

• Always keep LP gas tanks in upright position.

Do not store (or use) gasoline or other flammable

vapors and liquids in the vicinity of this gas grill.

• LP gas tanks not connected for use must NOT be stored on bottom shelf or in the vicinity of this or any other gas grill.

• Do not subject the LP gas tank to excessive heat.

• Never store an LP gas tank indoors. If you store your gas grill in the garage or other indoor location, always disconnect the LP gas tank

first and store it safely outside.

,4kWARNING

If you smell gas:

• Shut off gas supply to the gas grill.

• Turn the Control Knobs to OFF position.

• Extinguish any open flame such as candle, cigarette, lighter, etc., that could cause gas to ignite.

• Open the Grill Lid.

• Get away from the LP gas tank.

• Do not try to fix the problem yourself.

• If odor continues or you have a fire you cannot extinguish, call your fire depart-

ment. Do not call near the LP gas tank because your telephone is an electrical

device and could create a spark resulting

in fire and/or explosion.

NOTE: The normal flow of gas through the regulator and hose assembly can create a humming noise. A low volume of noise is

perfectly normal and will not interfere with operation of the grill. If humming noise is loud and excessive you may need to purge air from the gas line or reset the regulator excess gas flow device. This purging proce- dure should be done every time a new LP gas tank is connected to your grill. For help

call the Grill Information Center for assis- tance, 8am - 8pm CST, Monday through

Friday 1-888-317-7642.

Figure 1 (Naturalgas model only)

IMPORTANT:your Kenmore Natural Gas Grill cannot

be converted to use LP Gas. Attempting to do so is extremely hazardous and will also void the grill

warranty.

Your natural gas grill is designed to operate on

natural gas only, at a pressure of 7" water column (W.C.) (1/4 psi or 1.75 kpa), regulated at the residential meter. Check with your gas utility company for local gas pressure and with your local municipality for building code requirements. If your residential gas line pressure has not been regulated to 7" W.C., contact your local gas utility company for professional assistance.

It is recom mended that a Shutoff Valve be installed at the gas supply source outdoors, install at apoint after the gas pipe exits the outside wall and before

the quick-disconnect hose, or install it at the point before the gas line piping enters the ground.

See Figure 1.

• Pipe sealing compound or pipe thread tape resistant to the action of natural gas must be used on all male

pipe threadswhen making the connection.

Disconnect your gas grill from fuel source when the gas supply is being tested at high pressures. Thisgasgrill and itsindividual shutoffvalve must be disconnected from the gas supply pipe system during any pressure testing of that system at

pressure in excess of 1/2 psi (3.5kpa).

TO GRILL

MALE

F_TTING

OUTSIDE WALL

LOCKING

SHUT OFF

QUICK DISCONNECT

GAS SUPPLY

INSIDE

WALL

SHUT OFF

Turn off your gas grill when the gas supply is being tested at low pressures. The grill must be isolated from the gas supply pipe system by closing itsindividual manual shutoff valve during any pressure testing of the gas supply pipe system at pressures equal to or less than 1/2 psi (3.5kpa).

CAUTION:Spidersandsmallinsectsocca- sionallyspinwebsor makenestsin the grill

BurnerTubesduringtransitandwarehousing. Thesewebscanleadto a gasflowobstruc-

tionwhichcouldresultin a fire in and around theBurnerTubes.Thistype of fire is known

as a "FLASHBACK"and cancauseserious damageto yourgrillandcreatean unsafe

operatingconditionfor the user. To reducethe chanceof "FLASHBACK",you

mustcleanthe burnertubesbeforeassem- blingyourgrill, andat leastoncea monthin

latesummeror earlyfall whenspidersare mostactive.AlsoperformthisBurnerTube cleaningprocedureif yourgrillhasnotbeen

usedfor an extendedperiodof time.

Figure 1

SPARKELECTRODE

TO CLEAN BURNER TUBE, INSERT HOOK HERE

ASSEMBLY \\

To reduce the chance of "FLASHBACK" (see

CAUTION at left) clean the Burner Tubes and Burners before fully assembling your grill.

Remove the Cotter Pin from the rear underside

of each Burner using a pair of long nose pliers.

Carefully lift each Burner up and away from the Gas Valve Orifice, then refer to Figure 1 and perform one of these three cleaning methods:

Bend a stiff wire, (a lightweight coat hanger works well) into a small hook as shown below. Run the hook through the Burner Tube

and inside the Burner several times to remove any debris.

( J

. Use a bottle brush with a flexible handle.

.. ')

Run the brush through the Burner Tube and inside the Burner several times, removing any

debris.

Use an air hose to force air through each Burner Tube. The forced air should pass

debris or obstructions through the Burner and out the Ports.

GAS COLLECTOR BOX

BURNER BURNER PORT

BURNER TUBE

Long nose pliers can be used to remove Cotter Pin when cleaning the Burners Use work gloves to protect your hands Wear eye protection When you have finished assembling your grill we strongly urge that all Pattern Head Thumb Screws be tightened, either with the supplied Tightening Tool or a #2 Phillips Head Screwdriver

Tightening Tool

Ref. # P05515102K

FOOT

COTTER PIN

Z WARNING

The location of the Burner Tube with re- spect to the Orifice is vital for safe opera-

tion. Check to ensure the Orifice is inside the Burner Tube before using your gas grill.

See Figure 2. If the Orifice is not inside the Burner Tube, lighting the Burner may cause explosion and/or fire.

Figure 2

J \

GASVALVE \ ASSEMBLY ORIFICE BURNER TUBE

The following table illustrates a breakdown of the hardware pack. It highlights what components are used in the various stages of assembly.

Ref.

S211G06352 S431M08152

S313G06082 S132G04082

S135G04332 S132G04082

S132G04082 S132G04082

S135G04332 PO5318022B

S132G04082 S132G04121

S135G04101 S132G04082

S132G04122 S132G04122

Component Qty. Wheel Bolt 3/8"x3-3/8" 2

Spring Washer 2 Nut 3/8" 2

Pattern Head Screw 1/4"xl/2" 4 Pattern Head Screw 1/4"x2-3/4" 8

Pattern Head Screw 1/4"xl/2" 4

Pattern Head Screw 1/4"xl/2" 4 Pattern Head Screw 1/4"xl/2" 8 Pattern Head Screw 1/4"x2-3/4" 4

Door Stop/Magnet 2 Pattern Head Screw 1/4"xl/2" 4

Pattern Head Screw 1/4"x3/4" 4 PatternHeadPartly-ThreadedScrew1/4"x5/8" 4

Pattern Head Screw 1/4"x1/2" 2 Pattern Head Screw 1/4"x3/4" 4

Pattern Head Screw 1/4"x3/4" 4

PurposeofComponents

Install Wheels To Cart Legs

Attaches Foldable Cart Legs Attaches Cart Legs To Cart Bottom Shelf Attaches Tank Pull-out Tray Assembly To Cart

Bottom Shelf

Attaches Cart Rear Panel To Cart Attaches Cart Side Panels To Cart

Attaches Door Bracket To Cart Attaches To Cart

Attaches Magnetic Door Stop To Cart Attaches Door Handles To Doors

Attaches Doors To Cart Attaches Cart Spice Basket To Left Door

Attaches Left Side Shelf To Grill Head Attaches Side Burner Frame To Grill Head

S233G04332 PO5301001A P05515101L P05313023B S132M04082 PO5515102K

P03426061C Control Knob 1 P05501010B Cotter Pin 1 S132M04082 Pattern Head Screw M4x8mm 2 S411M04122 Plain Washer M4 2 S132M04082 Pattern Head Screw M4x8mm 2

Already installed in the Tool Holder Kit & Towel Rack

$132Mg5082 Pattern Head Screw M5x8mm 2 $411Mg5136 Plain Washer M5 2

S132M05082 Pattern Head Screw M5x8mm 2 S411M05136 Plain Washer M5 2

Wing Bolt 1/4"x2-3/4" 1 Battery/AA 1

Wrench/No.17 Customized 1 Lighting Stick 1

Pattern Head Screw M4x8mm 1 Tightening Tool 1

Secures Gas Tank

Powers The Electric Ignitor Tighten Caster & Wheel Bolt Attaches to Bowl Support Bracket, Left Attaches to Bowl Support Bracket, Left Allows you to tighten Pattern Head Thumb Screws

after assembly

Install To Side Burner Gas Valve Stem Secure To Side Burner

Attaches To Side Burner Gas Valve Bracket Attaches To Side Burner Gas Valve Bracket

Attaches To Left & Right Bowl Panel for Bowl Wind Shield

Attaches Towel Rack to Left Side Shelf

Attaches Tool Holder to Side Burner Frame

LPG GAS MODEL ONLY

Size and Quantity of each Hardware Piece:

Wheel Bolt 3/8"x3_3/8"

Qty. 2 Ref. # $211G06352

Pattern Head Screw 1/4"x2-3/4" Qty, 12

Ref. # $135G04332

PatternHeadParUy.ThreadedScrew 1/4"x5/8" Qty. 4

Ref. # $135G04101

Lighting Stick Qty. 1

Ref. # P05313023B Scale 1:2

Battery/AA Qty, 1 Ref, # P05301001A

Scale 1:2

Spdng Washer Qty, 2

Ref. # $431M08152

Pattern Head Screw 1/4"x3/4" Qty. 8

Ref. # $132G04122

Pattern Head Screw M4x8mm Qty. 5

Ref. # $132M04082

Nut 3/8" Qty. 2

Ref. # $313G06082

Pattern Head Screw 1/4"xl/2"

Qty, 26

Ref. # $132G04082

Door Stop/Magnet Qty. 2

Ref. # P05318022B Scale 1:2

Plain Washer M4 Qty. 2

Ref. # $411M04122

Control Knob Qty. 1

Ref. # P03426061C Scale 1:2

Wrench/No,17 Customized Qty. 1

Ref. # P05515101L Scale 1:2

Hardware already installed in the Tool Holder Kit & Towel Rack

Pattern Head Screw MSx8mm Qty. 4

Ref. # $132M05082

Plain Washer M5

Qty, 4

Ref. # $411M05136

Tightening Tool Qty. 1

Ref. # P05515102K

Wing Belt 1/4"x2_3/4"

Qty. 1 Ref. # $233G04332 Scale 1:2

Cotter Pin Qty. 1

Ref. # P05501010B

-I

Pattern Head Screw 1/4"x3/4"

Qty. 4 Ref. # $132G04121

The following table illustrates a breakdown of the hardware pack. It highlights what components are used in the various stages of assembly.

Refi

$211G06352 $431 M08152

$313G06082

S132G04082

$135G04332 S132G04082

S132G04082 $135G04332

PO5318022B

S132G04082 $132G04121

$135G04101 S132G04082

S132G04082 S132G04122 S132G04122

Component Qty.

Wheel Bolt 3/8"x3-3/8" 2

Spring Washer 2 Nut 3/8" 2

Pattern Head Screw 1/4"xl/2" 4 Pattern Head Screw 1/4"x2-3/4" 8 Pattern Head Screw 1/4"xl/2" 4 Pattern Head Screw 1/4"xl/2" 8 Pattern Head Screw 1/4"x2-3/4" 4

Door Stop/Magnet 2 Pattern Head Screw 1/4"xl/2" 4

Pattern Head Screw 1/4"x3/4" 4 PatlemHeadPartly-ThreadedScrew1/4"x5/8" 4

Pattern Head Screw 1/4"x1/2" 2 Pattern Head Screw 1/4"x1/2" 2

Pattern Head Screw 1/4"x3/4" 4 Pattern Head Screw 1/4"x3/4" 4

Purpose of Components

Install Wheels To Cart Legs

Attaches Attaches Attaches Attaches Attaches

Attaches Attaches Attaches Side Burner Frame To Grill Head

Foldable Cart Legs Cart Legs To Cart Bottom Shelf

Cart Rear Panel To Cart Cart Side Panels To Cart Door Bracket To Cart

To Cart

Magnetic Door Stop To Cart Door Handles To Doors

Doors To Cart Cart Spice Basket To Left Door

Cart Spice Basket To Right Door Left Side Shelf To Grill Head

PO5301001A

PO5515101L P05313023B

$132M04082

PO5515102K

P03426061C Control Knob 1 P05501010B Cotter Pin 1

$132M04082 Pattern Head Screw M4x8mm 2 $411M04122 Plain Washer M4 2 $132M04082 Pattern Head Screw M4x8mm 2

Already installed in the Tool Holder Kit & Towel Rack

$132M05082 Pattern Head Screw M5x8mm 2 $411M05136 Plain Washer M5 2

Battery/AA 1

Wrench/No. 17 Customized 1

Lighting Stick 1 Pattern Head Screw M4x8mm 1

Tightening Tool 1

Powers The Electric Ignitor Tighten Caster & Wheel Bolt Attaches to Bowl Support Bracket, Left Attaches to Bowl Support Bracket, Left

Allows you to tighten Pattern Head Thumb Screws after assembly

Install To Side Burner Gas Valve Stem Secure To Side Burner Attaches To Side Burner Gas Valve Bracket Attaches To Side Burner Gas Valve Bracket

Attaches To Left & Right Bowl Panel for Bowl Wind Shield

Attaches Towel Rack to Left Side Shelf

Attaches Tool Holder to Side Burner Frame

NG GAS MODEL ONLY

Size and Quantity of each Hardware Piece:

Wheel Bolt 3/8"x3-3/8" Qty. 2

Ref. # $211G06352

Pattern Head Screw 1/4"x2-3/4" Qty. 12

Ref. # $135G04332

PatternHeadParUy.ThreadedScrew 1/4"x5/8" Qty. 4

Ref. # $135G04101

Lighting Stick Qty. 1

Ref, # P05313023B Scale 1:2

Battery/AA Qty. 1

Ref. # P05301001A Scale 1:2

Spring Washer

Qty. 2

Ref. # $431M08152

Pattern Head Screw 1/4"x3/4"

Qty. 8

Ref. # $132G04122

Pattern Head Screw M4xSmm Qty. 5

Ref. # $132M04082

Nut 3/8" Qty. 2

Ref. # S313G06082

Pattern Head Screw 1/4"xl/2" Qty. 24

Ref. # $132G04082

Door Stop/Magnet

Qty. 2

Ref, # P05318022B

Scale 1:2

Plain Washer M4 Qty. 2

Ref. # $411M04122

Control Knob Qty. 1

Ref. # P03426061C Scale 1:2

Wrench/No.17 Customized Qty. 1

Ref. # P05515101L Scale 1:2

Hardware already installed in Tool Holder Kit &

Towel Rack

Pattern Heed Screw M5x8mm Qty. 4

Ref. # $132M05082

I..i

Plain Washer M5 Qty. 4

Ref. # $411M05136

Tightening Tool Qty. 1

Ref. # P05515102K

Pattern Head Screw 1/4"x3/4" Qty. 4

Ref. # $132G04121

i.J

Cotter Pin Qty. 1

Ref. # P05501010B

(NO ONLY)11a_

15_

(NO ONLY)

_57 (NG ONLY)

REF# DESCRIPTION

PART#

QTY

1. Lid

2. Lid Trim Plate

3. Lid Hinge Support, Right

4. Lid Hinge Support, Left

5. Temperature Gauge

6. Lid Handle

7. Name Plate

8. Cooking Rack/Secondary

9. Cooking Grid

10. Flame TamedSteel

11. Burner/Main

1la. Burner Air Shutter/Main Bumer (NG only)

12. Burner Bracket

13. Gas Collector Box with Electrode

14. Electric Wire Set

15. Electric Ignitor, 4-port 15a. Battery/AA 16a. Bowl Panel, Front 16b. Bowl Panel, Rear

16c. Bowl Panel, Left

16d. Bowl Panel, Right

17. Bowl Hinge Support

18. Bowl Support Bracket, Left

19. Bowl Support Bracket, Right

20. Grease Draining Tray

21. Grease Draining Tray Heat Shield

22. Grease Receptacle

23. Gas Valve/Manifold Assembly LPG

24. Protective Pad

25. Control Knob for Main Burner

26. Control Panel LPG NG

27. Side Shelf

28. Side Burner Frame

29a. Cart Bottom Shelf (LPG only) 29b. Cart Bottom Shelf (NG only)

30. Cart Rear Panel

31. Door Bracket

32. Cart Side Panel

33. Door, Left

34a. Door, Right (LPG only) 34b. Door, Right (NG only)

35. Door Handle

POO138026A POO11402JV

P03322001C P03322002C P00601174A P00205007B P00410037C

P01506001E P01615002E P01705002E P02001008C P05524060C

P02204031B P02608001A P02615004A P02502024C P05301001A

P0073811GA P0072510GA P00720054A P00721054A P03321O01D P01304O03D

P01305O03D P02706035B P06903006B P02701075B

YOO60076 Y0060077

P055180031 P03412331C

P02908027B P02908027G

P01102004C P01104002C P01004O03D

P01004O04D P07702016B P03301O06D P07604001B P04302007A P04303007A

P04303010A P00203003C

1 1 1 1

1 1 1 1 4 4

4 4 1 2 1

1 1 1 1 1

1 2 1 1 1 1

1 1

2 4

1 1

1 1 1

2 1 1 1 2

REP# DESCRIPTION PART# QTY

36. Door Stop/Magnet P05318022B 2

37. Tank Pull-Out Tray Assembly (LPG only) Y0340010

38. Cart Leg, Left-front (Caster side) P00910003C 1

39. Cart Leg, Left-back (Caster side) P00911003C 1

40. Cart Leg, Right-front (Wheel side) P00912003C 1

41. Cart Leg, Right-back (Wheel side) P00913003C 1

42. Caster Seat PO4513OO1A 2

43. Caster, 3 in., with Brake P05106001A 2

44. Wheel P05101001A 2

45. Wheel Hub Cap P05116001B 2

46. Wrench/No.17 Customized P05515101L 1

47. Tightening Tool P05515102K 1

48. Lighting Stick P05313023B 1

49. Towel Rack P05209001A 1

50. Tool Holder PO5514003F 1

51. Tool Hook P05514053A 5

52. jCa_ Spice Basket NG P05204002C 2

53. Side Burner Lid P0011503EA 1

54. Side Burner Pot Support P00805013B 1

55. Side Burner Electrode P02607042J 1

56. Side Burner LPG P02002041C 1 NG P02002009C 1

56a. Burner Air Shutter/Side Burner (NG only) P05524007C 1

57. Side Burner Gas Valve Assembly LPG P03218003G

NG PO3218O04G 1

58. Side Burner Connection Tube P03705002A

59. Regulator with Hose/LPG P03601005A

60. Hose, 12 ft./NG P03703001A

61. Control Knob for Side Burner P03426061C

62. Bowl Wind Shield PO0737021B

63. Side Burner Wind Shield P06908001C

--- Owner's Manual P80102001B

--- Hardware Pack (LPG only) P06O01011A

--- Hardware Pack (NG only) P06001007A

For the repair or replacement parts you need: Call anytime

P05204002C 1

1 1 1

1 1 1 1

1 1 1

1-800-4-MY-HOM E °(1-800-469-4663)

To make sure you obtain the correct replacement parts for your Kenmore gas grill, please refer to the

part numbers in this parts list. The following information is required to ensure you receive the correct

parts: ,

1. Mooe and Serial Number (see CSA label on grill)

2. Part Number

3. Part Description

4. L4uantity or parts needed

Important: Keep this Owner's Manual for convenient referral and for part replacement. Important: Use only, Seam" authorized, ports. The. use of any part that is not Sears authorized can be

aangerous ana Will also vola your proauc[ warran[y.

CAUTION:Whileit is possible for one person to assemble this grill, obtain assistance from another person when

handling some of the larger, heavier pieces, especially the grill head.

1. During unpacking and assembly always wear work gloves and eye protection.

2. Open Lid of shipping carton and remove top sheet of cardboard. Lay cardboard sheet on floor and use as a work surface to protect floor and grill parts from scratches.

3. Remove packing materials and cart parts from shipping carton.

4. You may slice the carton front corners with a utility knife to lay open the carton front panel. This will allow you to raise the grill head Lid and remove the components packed inside the head, making it easier to lift.

5. With an assistant, lift the grill head out of the shipping carton and place it on the cardboard work surface.

6. Use the parts list to check that all parts have been included.

7. Inspect the grill for damage as you assemble it. Do not assemble or operate the grill if it appears damaged. If there are damaged or missing parts when you unpack the shipping box, or you have questions during the

assembly process, call the:

Grill Information Center 1-888-317-7642

8am - 8pm CST, Monday through Friday

_1_ Assembling The Cart To The Grill Head

Lay the Grill Head flat on its back as shown. Cut Fastening Bands from folded Cart Legs. Unfold the 4 pre-assembled Cart Legs. Insert 4 screws provided as shown and tighten securely.

Pattern Head Screw 1/4"xl/2"

Qty. 4

Ref. # $132G04082

+ 28 hidden pages