Kenmore 14115284900 Owner’s Manual

Use and Care Guide

Dual Purpose Electric Grill

QLISTED

Model 141.15284900

This dual purpose grill can be used as a portable model or attached to the included grill cart as shown above right.

Call us first if you have any problem with
this product. We can help you with ques-
tions about assembly and grill operation or

ifthere are damaged or missing parts when

you unpackthis unit from the shipping box.

Please call before contacting your local
retailer.

1-888-317-7642

8am-8pm CST, Monday throu,qh Friday

• NOTE TO ASSEMBLER/INSTALLER:
Leave this Guide with the consumer.

• NOTE TO CONSUMER:
Keep this Guide for future reference.

• RECORD YOUR SERIAL #

(See rating label on grill)

Sears, Roebuck and Co., Hoffman Estates, IL 60179, USA www.sears.com

• Failure to comply with these instructions could
result in a fire or electric shock that could cause

serious bodily injury or property damage.

• FOR OUTDOOR USE ONLY. DO NOT USE

INDOORS OR FOR COMMERCIAL COOK-
ING.

Whether this grill was assembled by you orsome-
one else, you must read this entire manual
before using your grill to ensure the grill is
properly assembled, installed and maintained.

Your grill will get very hot. Always wear aflame

retardant BBQ Mitt when cooking on your grill.
Never lean over cooking areaswhile using grill. Do
not touch cooking surfaces, Lid, grill housing or
other partswhile grill is inoperation, or until the grill

has cooled down after use.

Useyour grill at least 2 feet away from any wall
or surface. Use your grill at least 2feet away from

combustible objects that can melt or catch fire
(such as vinyl or wood siding, fences and over-
hangs) or sources of ignition including pilot lights
on water heaters and live electrical appliances.

Guide # P80174010H - Date:2008/11/19

Primary Safety Warnings ........................... 1-3

Warranty Terms and Conditions .................. 3

Pre-Assembly Instructions ............................... 3

Part Diagrams and Lists ........................... 4-6

Assembly Instructions ................................. 7-11

Use & Care ............................................ 12-13

Troubleshooting ............................................... 13

Cleaning and Maintenance .......................... 14

Cooking Guide .............................................. 15

Repair Protection Agreements ..................... 16

When using this grill or any electrical appliances,
basic safety precautions should always be followed
including the following:

• Read all Instructions

• Do not touch hot surfaces. Use handles or knobs.

• To protect against electrical shock do not im-
merse cord, plugs, or this grill in water or other
liquid.

• Close supervision is necessary when any
applance is used by or near children.

• Unplug from outlet when not in use and before
cleaning. Allow to cool before putting on or tak-
ing off parts.

• Do not operate any appliance with a damaged
cord or plug or after the appliance malfunctions
or has been damaged in any manner. Return
appliance to the nearest authorized service fa-
cility for examination, repair, or adjustment.

• The use of accessory attachments not recom-
mended by the appliance manufacturer may
cause injuries.

• Do not let cord hang over edge of table orcounter,
or touch hot surfaces.

• Do not place on or near a hot gas or electrical
burner, or in a heated oven.

• Extreme caution must be used when moving an
appliance containing hot oil or other hot liquids.

• Attach the plug of the appliance to the recep-
tacle of power supply extension cord first, then
plug cord into the wall outlet.To disconnect, turn
any control to "off", then remove plug from wall

outlet.

• Do not use appliance for other than intended
use.

• Fuel, such as charcoal briquettes, is not to be
used with appliance.

• Use only on properly grounded outlet.

• A short power-supply cord (or detachable power-
supply cord) isto be provided to reduce the risk
resulting from becoming entangled in or tripping
over a longer cord.

• Longer detachable power-supply cords or ex-
tension cords are available and may be used if

care is exercised in their use.

• If a longer detachable power-supply cord or
extension cord is used:

1) The marked electrical rating of the cord set
or extension cord should be at least as great as
the electrical rating of the appliance, and

2) The cord should be arranged so that it will
not drape over the countertop or tabletop
where it can be pulled on by children or tripped
over unintentionally.

3) The appliance is of the grounded type, the
extension cord should be a grounding-type 3-

wire cord.

• Outdoor extension cords should be used with
outdoor use products and with a tag stating

"Suitable for Use with Outdoor Appliances".
The connection to an extension cord should be

kept dry and off the ground.

• Store products indoors when not in use - out of
the reach of children.

• Do not clean this product with a water spray or
the like.

SAVE THESE

INSTRUCTIONS

Remove the Grease Receptacle BEFORE detach-
ing the Grill Head for portable or table-top use.

Reinstall the Grease Receptacle once the Grill Head
is firmly in position (with legs opened and placed

on a flat surface).

n

instructions could result in afire orexplosion that
could causeserious bodily injury, death or prop-

I Failure to read and follow the Use and Care

erty damage.

California Proposition 65
Brass components, such as the rheostat valve

stem used on this electric grill, contain lead which
is known to the State of California to cause

cancer, birth defects, or other reproductive
harm.

KenmoreFull Warranty

If this grill fails due to a defectin materialor

workmanshipwithinone year from the date of

aurchase,call 1-800-4-MY-HOME® to arrangefor
freerepair(orreplacementif repairprovesimpos-
sible).

Limited Warranty on Selected Grill Parts
From the date of purchase for the time periods listed
below, the following grill parts will be replaced free
of charge if they rust through. After the first year
from the date of purchase you must pay the labor

cost to have them installed.

ELECTRIC SHOCK CAN KILL OR RESULT
IN SERIOUS INJURY.

TO PREVENT ELECTRICAL SHOCK:

• Connect cord to properly grounded GFCI
(Ground Fault Circuit Interrupter) outlet only.

• Never operate your electric grill when it is
raining.

• Always keep cord dry and off the ground.

• Stainless Parts 3 Years

• Painted Parts 2 Years

• Cooking Grids 2 Years
All warranty coverage excludes grill part paint loss

or surface rusting, which are either expendable parts
that can wear out from normal use in less than a

year, or are conditions that can be the result of
normal use, accident or improper maintenance.

All warranty coverage is void if this grill is ever used
for commercial or rental purposes.

All warranty coverage applies only if this grill is used
in the United States.

This warranty gives you specific legal rights, and
you may have other rights which vary from state

to state.

Sears, Roebuck and Co., Hoffman Estates, IL

© Sears Brands, LLC

PRE-ASSEMBLY

Readandperformthefollowing pre-assemblyinstructions:

[] Tools Required forAssembly include:

• protectivework gloves

• For your safety, obtain assistance from another
personwhen assembling this grill.

• #2 & #3 PhillipsHead Screwdriver

[] Open lid of shipping carton and remove parts box and

packing materials. Open Grill Head Lid and unpack parts
inside. Remove and discard all packing materials from
parts.

[] You may slice the carton front corners with a utility knife

to lay open the carton front panel. This allows you to raise
the grill head lidand remove the components packed in-
side, making iteasier to lift. Use the sliced off carton front
as a work surface to protect floor and grill parts from

scratches.

[] Use the Hardware and Part Diagrams to ensure all items

are included and free of damage.

[] Do not assemble or operate the grill if it appears

damaged. If there are damaged or missing parts when
you unpack the shipping box or you have questions
during the assembly process, call the GRILL INFOR-
MATION CENTER 1-888-317-7642 8am - 8pm CST,
Monday through Friday.

• Never put the cord or heating element in water
or any liquid.

• To prevent your grill from being splashed by
water or falling into water, do not use grill

within 10 feet of pool, spa, pond, water faucet
or any body of water.

• Make sure the control knob is set to OFF
before plugging OR unplugging your grill.

• Unplug your grill when not in use or before
moving the grill.

• Do not unplug your grill by pulling the cord.

• Keep cord away from hot grill surfaces.

• Never operate your grill if the cord or plug
appears damaged.

• Never remove the grounding plug or use with
an adapter to two prongs.

• Unplug the cord before using water or any
liquid to clean your grill.

Since 1971 the National Electric Code (NEC)
has required Ground Fault Circuit Interrupter

devices on all outdoor circuits.

If your residence was built before 1971,
check with a qualified electrician to deter-
mine if a Ground Fault Circuit Interrupter
protector exists.

Do not use this appliance if the circuit does
not have GFCI protection.

Do not plug this grill into an indoor electrical
circuit.

Save These Instructions

I

for Future Reference

3

PART#

P06001078A

P05501106B

S411G07014
S112G0432A

S112G0408A
S233G0410A

PD13010034

S138G0410A

S193G0407A

Wing Bolt 1/4"x5/8" Washer/Plain 7/16" Cotter Pin Pattern Head Screw Special Flat Head
Qty. 6 Qty. 2 Qty. 2 1/4"x5/8" Screw 1/4"x7/16"

Part # $233G0410A Part # $411G07014 Part # P05501106B Qty. 4 Qty. 2

PART DESCRIPTION
Hardware Pack

Cotter Pin
Washer/Plain 7/16"

Phillips Head Screw 1/4"x2"
Phillips Head Screw 1/4"xl/2"

Wing Bolt 1/4"x5/8"
Control Knob for Electric Burner
Pattern Head Screw 1/4"x5/8"

Special Fiat Head Screw 1/4"x7/16"

QTY PURPOSE OF PART

1 For use in assembtyof Mode1141.15284900

2 Attaches Wheel Axle and Wheels to Lower Right Cart
2 Legs

8 Attaches Cart Bottom Shelf Bracket between Cart legs
8 Attaches Bowl Bracket to Upper Cart Legs

6 Attaches Grill Head onto Bowl Bracket

1 Attaches to Control Panel
4 Attaches Side Shelf to Cart Legs
2 Attaches to Grease Tray Bracket

Part # S 138G0410A Part # S193G0407A

/

/

J

Phillips Head Screw Phillips Head Screw
1/4"xl/2" 1/4"x2" Control Knob for Electric Burner

Qty. 8 Qty. 8 Qty. 1

Part # S112G0408A Part # S112G0432A

Part # PD 13010034

AC Power Rate: 120 VAC / 60 Hz, 1,700 Watts
Temperature Setting Range: 120°F ~ 570°F

Thermostat Electric Timer Indicator Heat Element

AC120V/60Hz 120°F~570°F Module 120VAC 120VAC/1,700Watt

Green/AWG14/105°C

Chassis

White/AWG14/105°C

White/AW G18/105°Q

White/AW G14/200°C

Black/AW G 18/105°C

Black/AW G 14/200°C

WARNING: If any of the original wire supplied with the appliance needs to be replaced, it must be replaced

with specified type as above or its equivalent.

4

J

11f

"\\

11 /

/

J

i

KEY DESCRIPTION PART# QTY

1 Lid PD01010013 1
2 Name Plate P00410041C 1
3 Protective Pad P055180011 4

4 Lid Latch, Upper PD03010011 2
5 Lid Handle Heat Insulating Spacer P06801030A 2
6 Lid Handle PD02010021 1

7 Cooking Grid PD07010013 1
8 Burner Bracket PD16010252 1

9 Burner, Electric PD05010010 1

10 Bowl, Inner PD04020011 1
11 Thermostat Bracket PD08010023 1
12 Thermostat Protector PD08010042 1

13 Lid Latch, Lower PD03020011 2
14 Bowl, Outer PD04010013 1
15 Grease Tray Bracket PD16040012 2
16 Bracket, Foldable Leg PD16010062 4

17 Leg, Foldable PD17030012 4
18 Leg Grip PD17040012 4

19 Control Panel Heat Shield PD08010013 1

20 Insulation Cap PD06020010 2
21 Control Panel Assembly PD09010033 1
22 Control Knob PD13010034 1

23 Grease Draining Tray PD14010012 1
24 Grease Receptacle PD14020022 1

25 Side Shelf, Right PD19020032 1
26 Bowl Bracket PD16010052 2

27 Cart Leg, Upper PD17010052 4
28 Cart Leg, Lower Left PD17020072 2
29 Cart Bottom Shelf PD20010022 1

30 Wheel P05101001A 2
31 Wheel Hub Cap P05116002C 2

32 Wheel Axle PD18010012 1
33 Cart Leg, Lower Right PD17020062 2

34 End Cap, Leg PD21010015 2
35 Lid Heat Insulator PD01020032 1

36 Lid Heat Shield PD01020040 1
37 Bowl Heat Insulator PD04010020 1

38 Electric Burner Insulating Spacer P06801031F 2

Hardware Pack P06001078A 1
Use and Care Guide P80174010H 1

Note: This grill can be assembled in approximately 30 minutes.

For the repair or replacement parts you need:

Call anytime 1-800-4-MY-HOME® (1-800-469-4663)

To obtain the correct replacement parts for your electric grill, please refer to the part numbers in this parts list.
The following information is required to ensure you receive the correct parts:

1. Model and Serial Number (see UL label on grill)

2. Part Number

3. Part Description

4. Quantity of parts needed

Important: Use only Sears replacement parts. The use of any part that is not a Sears replacement part can be danger-
ous and will also void your product warranty. Keep this Use and Care Guide for convenient referral and for part replace-

ment.

6

CAUTION•Whileitispossibleforonepersontoassemblethisgrill,obtainassistancefromanother

whenhandlingsomeofthelarger,heavierpieces.

Install Wheels

[] Insert WheeIAxte through the Wheels and Lower Left Cart Legs.
[] Insertone 7/16" Washer over each end of WheeIAxte and secure Cotter

Pin as shown. Push cotter pin down fully into wheel axle.

[] Snap the Wheel Hub Caps onto the Wheels.

Lower Left

Washer/Plain 7/16" \
Qty. 2 ",\

Part# S411G07014 _k /

Cotter Pin
Qty. 2

Part # P05501106B

\\

\

\ j_.

\.

Wheel
HubCap

Wheel

Cart Legs

Wheel

Axle

9erson

Install Cart Legs

[] Align the two holes on the Lower Cart Legs with the threaded holes on

the Upper Cart Legs and then attach as shown.
Note: Make sure that the side of Upper Cart Legs with raised holes

face outward.

The raised holes face outward

s

/,

Upper Left

Cart Legs

Upper Right

Cart Legs

Lower Right
Cart Legs

7

Install Cart Bottom Shelf

[] Attach the Cart Bottom Shelf between the Cart Legs (as shown).
[] Tighten securely using 8 Phillips Head Screws 1/4"x2".

Phillips Head Screw
1/4"x2"

Qty. 8

Part # S112G0432A

Install Bowl Brackets

[] Attach the Bowl Brackets between the Upper Cart Legs. Slot in end

of Bracket goes over rivet in top of Leg. Tighten securely using 4

Phillips Head Screws 1/4"x1/2" as shown.
Note: Bracket Flange faces inward (see inset).

Bracket Flange faces inward

Phillips Head Screw
1/4"xl/2"

Qty. 8
Part # S112G0408A

8

Install Grill Head and Control Knob

[] With the aid of an assistant, place Grill Head onto Bowl

Brackets.

[] Tighten securely using 6 Wing Bolts 1/4"x5/8".
[] Attach Control Knob as shown.

Wing Bolt 1/4"x5/8"
Qty. 6

Part # S233G0410A

Control Knob for

Electric Burner

Qty. 1

Part # PD 13010034

Install Right Side Shelf

[] Install Right Side Shelf with 4 Pattern Head Screws 1/4"x5/8".

(You will need an assistant to hold the Shelf.)

Pattern Head Screw 1/4"x5/8"
Qty. 4

Part # S 138G0410A

/ / i

/ / /

9

Fold-Away Right Side Shelf Option

[] Grasp Right Side Shelf and lift enough to dislodge Shelf

slots from fixed position.

[] Lower Shelf down until it rests next to Legs.

For illustration purposes - Front View of the Right Side Shelf

=- I

I _ I I )

\

RightSide

Shelf

/

J

/

_'_ Install Grease Tray and Grease Receptacle

[] Slide the Grease Tray side tabs over the Grease Tray Bracket

side rails underneath the Grill Bowl.

[] Secure Special Fiat Head Screws 1/4"x7/16" to Grease Tray

Bracket. (Fig. 1).

[] The Grease Tray is required to be present and centered for your

safetE

[] Slide the Grease Receptacle over Grease Tray rails (on under-

side of Grease Tray) until it rests in place.

//

\\\\\

\

\\\\\\\\

\

Special Flat Head Screw
1/4"x7/16"

Qty. 2
Part # S193G0407A

Fig. 1

Grease Tray Bracket

10