Kenmore 141.15283702, 141.152832 Owner's Manual

Use and Care Guide

DualPurposeElectricGrill Model141.152832

LISTED

This dual purpose grill can be used as a portable model or attached to the included grill cart as shown above right.

Call us first if you have any problem with this product. We can help you with ques- tions about assembly and grill operation or if there are damaged or missing parts when you unpack this unit from the ship- ping box. Please call before contacting your local retailer.

1- 888-317-7642

8am-8pm CST, Monday throu,qh Friday

• NOTE TO ASSEMBLER/INSTALLER: Leave this Guide with the consumer.

• NOTETOCONSUMER: Keep this Guide for future reference.

" RECORDYOURSERIAL#

(See rating label on grill)

Failure to comply with these instructions could result in a fire or electric shock that could cause

serious bodily injury or property damage. FOR OUTDOOR USE ONLY. DO NOTUSE

INDOORS OR FOR COMMERCIAL COOKING. Whether this grill was assembled byyou or some-

one else, you must read this entire manual before using your grill to ensure the grill is

properly assembled, installed and maintained. Your grill will get very hot. Always wear aflame

retardant BBQ Mitt when cooking on your grill. Never lean over cooking areas while using grill. Do not touch cooking surfaces, Lid, grill housing or other partswhile grill isin operation, or until the grill

has cooled down after use. Use your grill at least 2feet away from anywall

or surface. Use your grill at least 2 feet away from combustible objects that can melt or catch fire (such as vinyl or wood siding, fences and over- hangs) or sources of ignition including pilot lights on water heaters and live electrical appliances.

Sears, Roebuck and Co., Hoffman Estates, IL 60179, USA www.sears.com

Guide# P80174003H- Date:2007/12/11

Primary Safety Warnings ........................... 1-3

Warranty Terms and Conditions .................. 3

Pre-Assembly Instructions .............................. 3

Part Diagrams and Lists .......................... 4-6

Assembly Instructions ............................... 7-11

Use & Care ........................................... 12-13

Troubleshooting .............................................. 13

Cleaning and Maintenance .......................... 14

Cooking Guide .............................................. 15

When using this grill or any electrical appliances,

basic safety precautions should always be

followed including the following:

• Read all Instructions

• Do not touch hot surfaces. Use handles or knobs.

• To protect against electrical shock do not immerse cord, plugs, or this grill in water or other liquid.

• Close supervision is necessary when any appliance isused by or near children.

• Unplug from outletwhen not in useand before cleaning. Allow to cool before putting on or taking off parts.

• Do not operate any appliance with a dam- aged cord or plug or after the appliance malfunctions or has been damaged in any manner. Return appliance to the nearest authorized service facility for examination, repair, or adjustment.

• The use of accessory attachments not recommended bythe appliance manufacturer may cause injuries.

• Do not let cord hang over edge of table or counter, or touch hot surfaces.

• Do not place on or near a hot gas or electrical burner, or in a heated oven.

• Extreme caution must be used when moving an appliance containing hot oil or other hot liquids.

• Attach the plug of the appliance to the receptacle of power supply extension cord first, then plug cord into the wall outlet. To disconnect, turn any control to "off", then remove plug from wall outlet.

• Do not use appliance for other than intended

use.

• Fuel, such as charcoal briquettes, is not to be used with appliance.

• Use only on properly grounded outlet.

• A short power-supply cord (or detachable power-supply cord) is to be provided to reduce the risk resulting from becoming entangled in or tripping overa longer cord.

• Longer detachable power-supply cords or extension cords are available and may be

used if care is exercised in their use.

• If a longer detachable power-supply cord or extension cord is used,

1) The marked electrical rating of the cord set or extension cord should be at least as great as the electrical rating of the appliance, and

2) The cord should be arranged so that it will

not drape over the countertop or tabletop where it can be pulled on by children or tripped over unintentionally..

3) The appliance is of the grounded type, the

extension cord should be agrounding-type 3- wire cord.

• Outdoor extension cords should be used with outdoor use products and with a tag stating

"Suitable for Use with Outdoor Appliances".

The connection to an extension cord should

be kept dry and off the ground.

• Store products indoors when not in use- out of the reach of children.

• Do not clean this product with a water spray or the like.

SAVE THESE

INSTRUCTIONS

Remove the Grease Receptacle BEFORE detach- ing the Grill Head for portable or table-top use.

Reinstall the Grease Receptacle once the Grill Head is firmly in position (with legs opened and placed on a flat surface).

Failure to read and followthe Use and Care

instructions could result in a fire or explosion

that could cause serious bodily injury, death or

property damage.

California Proposition 65 Brass components, such as the rheostat valve

stem used on this electric grill, contain lead

which is known to the State of California to

cause cancer, birth defects, or other reproduc- tive harm.

KenmoreFull Warranty

If this grill fails due to a defect in material or

workmanship within one year from the date of

purchase, call 1-800-4-MY-HOME ® to arrange

for free repair (or replacement if repair proves

impossible). Limited Warranty on Selected Grill Parts

From the date of purchase for the time periods listed below, the following grill parts will be

replaced free of charge if they rust through. After the first year from the date of purchase you must pay the labor cost to have them

installed.

Stainless Parts 3 Years

Painted Parts 2 Years

Cooking Grids 2 Years

dl warranty coverage excludes wood discolora-

tion, grill part paint loss or surface rusting, which are either expendable parts that can wear

out from normal use in less than a year, or are

conditions that can be the result of normal use, accident or improper maintenance.

All warranty coverage is void if this grill is ever

used for commercial or rental purposes. All warranty coverage applies only if this grill is

used in the United States.

This warranty gives you specific legal rights, and you may have other rights which vary from state

to state.

Sears, Roebuck and Co., Hoffman Estates, IL

ELECTRIC SHOCK CAN KILL OR RESULT

IN SERIOUS INJURY. TO PREVENT ELECTRICAL SHOCK:

• Connect cord to properly grounded GFCI (Ground Fault Circuit Interrupter) outlet only.

• Never operate your electric grill when it is raining.

• Always keep cord dry and off the ground.

• Never put the cord or heating element in water or any liquid.

• To prevent your grill from being splashed by water or falling into water, do not use grill within 10 feet of pool, spa, pond, water faucet or any body of water.

• Make sure the control knob is set to OFF before plugging OR unplugging your grill.

• Unplug your grill when not in use or before moving the grill.

• Do not unplug your grill by pulling the cord.

• Keep cord away from hot grill surfaces.

• Never operate your grill if the cord or plug appears damaged.

• Never remove the grounding plug or use with an adapter to two prongs.

• Unplug the cord before using water or any liquid to clean your grill.

PRE-ASSEMBLY

Readandperformthefollowing pre-assemblyinstructions:

[] Tools Required forAssemblyinclude:

• protective work gloves

• For your safety, obtain assistance from another person when assembling this gas grill.

• #2 & #3 Phillips Head Screwdriver

[] Open lid of shipping carton and remove parts box and

packing materials. Lay cardboard sheet on floor and use as a work surface to protect floor and grill parts

from scratches.

[] You may slice the carton front corners with a utility

knife to lay open the carton front panel. This allows you to raise the grill head lid and remove the compo- nents packed inside, making it easier to lift. Use the sliced off carton front as a work surface to protect floor and grill parts from scratches.

[] Use the Hardware and Part Diagrams to ensure all

items are included and free of damage.

[] Do not assemble or operate the grill if it appears

damaged. If there are damaged or missing parts when you unpack the shipping box or you have questions during the assembly process, call the

GRILL INFORMATION CENTER 1-888-317-7642 8am - 8pm CST, Monday through Friday.

• Since 1971 the National Electric Code (NEC) has required Ground Fault Circuit Interrupter devices on

all outdoor circuits.

• If your residence was built before 1971, check with a qualified electrician to determine ifa Ground Fault

Circuit Interrupter protector exists.

• Do not use this appliance if the circuit does not have GFCl protection.

• Do not plug this grill into an indoor electrical circuit.

Save These Instructions

for Future Reference

PART #

P06001063A P05501106B $411G07014

$112G04324 S 112G04084

PD13010034 $233G04104 $138G04104 S 193G04074

PART DESCRIPTION Hardware Pack

Cotter Pin

Washer 7/16" T=1/16"

Phillips Head Screw 1/4"x2" Phillips Head Screw 1/4"xl/2"

Control Knob for Electric Burner

Wing Bolt 1/4"x5/8"

Pattern Head Screw 1/4"x5/8" Special Flat Head Screw 1/4"x7/16"

QTY

PURPOSE OF PART

For use in assembly of Model 152832

Attaches Wheel Axle and Wheels to Lower

Right Cart Legs

Attaches Cart Bottom Shelf Bracket

between Cart legs

8 Attaches Bowl Bracket to Upper Cart Legs 1 Attaches to Control Panel

6 Attaches Grill Head onto Bowl Bracket 8 Attaches Side Shelves to Cart Legs

2 Attaches to Grease Tray Bracket

Wing Bolt 1/4"x5/8" Washer 7/16" Cotter Pin Qty. 6 Qty. 2 Qty. 2

Part # $233G04104 Part # $411G070!4 Part # P05501106B

Phillips Head Screw Phillips Head Screw

1/4"xl/2" 1/4"x2" Control Knob for Electric Burner

Qty. 8 Qty. 8 Qty. 1 Part # S 112G04084 Part # S 112G04324 Part # PD 130 !0034

Pattern Head Screw Special Fiat Head

1/4"x5/8" Screw 1/4"x7/16"

Qty. 8 Qty. 2 Part # S 138G04104 Part # S 193G04074

AC Power Rate: 120 VAC / 60 Hz, 1,700 Watts Temperature Setting Range: 120°F ~ 570°F

Thermostat

AC120V/60Hz 120°F-570°F

White/AWG14/105°C _}'O White/AWG14/105°C

acldAWG14/105°C

Green/AWG14/105°C

Chassis

Electric Timer Indicator Heat Element

Module 120VAC 120VAC/1,700Watt

White/AWG14/200°C

White/AWG18/105°C

BlacWAWG18/105°C

Black/AWG14/200°C

WARNING: If any of the original wire supplied with the appliance needs to be replaced, it must be replaced

with specified type as above or its equivalent.

30 33

_34

27 27

KEY PART DESCRI PTION PART # QTY

1 Lid PD01010025 1

2 Lid Trim Plate PD01020025 1

3 Lid Handle PD02010045 1

4 Lid Handle Bracket P03303106A 2

4A Lid Handle Heat Insulating Spacer P06901025A 2

5 Name Plate P00410041C 1

6 Lid Latch, Upper PD03010011 2

7 Lid Latch, Lower PD03020011 2 8 Bowl Outer PD04010015 1

9 Bowl Inner PD04020012 1

10 Burner, Electric PD05010010 1 11 Cooking Grid PD07010013 1

12 Thermostat Bracket PD08010025 1 13 Thermostat Protector PD08010042 1 14 Burner Bracket PD16010025 1

15 Control Panel Heat Shield PD08010015 1 16 Control Panel Assembly PD09010035 1

17 Control Knob PD13010034 1 18 Leg, Foldable PD17030015 4

19 Leg Grip PD17040015 4 20 Grease Draining Tray PD14010015 1 21 Grease Receptacle PD14020025 1

22 Grease Tray Bracket PD16040015 2 23 Bowl Bracket PD16010045 2

24 Wood for Side Shelf and Cart Bottom Shelf PD15010010 11 25 Side Shelf Bracket, LF/RR PD16030055 2

26 Side Shelf Bracket, RF/LR PD16030065 2 27 Upper Cart Leg PD17010035 4

28 Cart Bottom Shelf Bracket PD16020015 2 29 Cart Leg, Lower Left PD17020011 2

30 Cart Leg, Lower Right PD17020065 2

31 End Cap, Leg PD21010010 2

32 Wheel Axle PD18010015 1

33 Wheel P05101001A 2

34 Wheel Hub Cap P05116002C 2

Hardware Pack P06001063A 1 Use and Care Guide P80174003H 1

Note: This grill can be assembled in approximately 30 minutes.

For the repair or replacement parts you need:

Call anytime 1-800-4-MY-HOME ® (1-800-469-4663)

To obtain the correct replacement parts for your electric grill, please refer to the part numbers in this parts list.

The following information is required to ensure you receive the correct parts:

1. Model and Serial Number (see UL label on grill)

2. Part Number

3. Part Description

4. Quantity of parts needed

Important: Use only Sears replacement parts. The use of any part that is not a Sears replacement part can be dangerous and will also void your product warranty. Keep this Operator's Guide for convenient referral and for part replacement.

CAUTION " While it is possible for one person to assemble this grill, obtain assistance from another person

when handling some of the larger, heavier pieces.

Install Wheels [] Thread Wheel Axle through the Wheels and Lower Left Cart Legs.

[] Insert one 7/16" Washer over each end of Wheel Axle and secure

Cotter Pin as shown.

[] Snap the Wheel Hub Caps onto the Wheels.

Washer 7/16" Qty. 2

Part # $411G07014

Cotter Pin Qty. 2

Part # PO5501106B

Install Cart Legs

[] Align the two holes on the Lower Cart Legs with the threaded

holes on the Upper Cart Legs and then attach as shown.

the label faces

W heel

Hub Cap

Wheel

Lower Left Cart Legs

W heel Axle

Wheel

Upper Left Cart Legs

Lower Left Cart Legs

Upper Right

Cart Legs

Lower Right Cart Legs

Install Cart Bottom Shelf

[] Attach the Cart Bottom Shelf between the Cart Legs (as

shown). Note: Ensure the label faces outward.

[] Tighten securely using Phillips Head Screws 1/4"x2".

Phillips Head Screw 1/4"x2"

Qty. 8

Part # $112G04324

H Install Bowl Brackets

[] Attach the Bowl Brackets between the Upper Cart Legs and

tighten securely using four 1/4"xl/2" Phillips Head Screws as shown.

Note: Ensure flat plate faces inward.

Fiat _plate faces inward

Phillips Head Screw 1/4"xl/2"

Qty. 8 Part # $112G04084

Install Grill Head and Control Knob

[] Place Grill Head onto Bowl Brackets. [] Tighten securely using six Wing Bolts 1/4"x5/8".

[] Attach Control Knob as shown.

Wing BoIt

1/4"x5/8"

Qty. 6 Part # S233G04104

Control Knob for Electric Burner Qty. 1

Part # PD130!0034

r_ install Side Shelves

Pattern Head Screw 1/4"x5/8"

Qty. 8

Part # S138G04104

[] install each Side Shelf with four 1/4"x5/8" Pattern Head Screws.

(You will need an assistant to hold each Shelf.)

Fold-Away Side Shelf Option

[] Grasp each side of Side Shelf and in one sweeping

action lift to dislodge the slot from the fixed position.

[] Pull Side Shelf away from the grill head and swing shelf

down until it rests adjacent to the Cart Legs.

For illustration purposes - Front View of the Right Side Shelf

I_11 Install Grease Tray and Grease Receptacle

[] Slide the Grease Tray side tabs over the Grease Tray Bracket

side rails underneath the Grill Bowl.

[] Secure Special Flat Head Screw 1/4"x7/16" to Grease Tray

Bracket. (Fig. 1).

[] The Grease Tray is required to be present and centered for

Left Side Shelf

Right Side Shelf

[] Slide the Grease Receptacle over Grease Tray rails (on

underside of Grease Tray) until it rests in place.

Special Flat Head Screw 114"x7/16"

Qty. 2 Part # S 193G04074

Fig. 1

Grease Tray Bracket

+ 23 hidden pages