Kenmore 14115223 Owner’s Manual

Owner's Manual

Liquid Propane Gas Grill

Model 141.152230

/_ WARNING:

Read this Owner's Manual carefully and be sure

your gas grill is properly assembled, installed and

maintained. Failure to follow these instructions

could result in serious bodily injury and/or property damage. This gas grill is intended for outdoor use only and is not intended to be installed in or on

recreational vehicles or boats.

Note to Installer: Leave this Owner's Manual

with consumer after delivery and/or installation.

Note to Consumer: Leave this Owner's Manual in a convenient place for future reference.

Sears, Roebuck and Co.,

Hoffman Estates, IL 60179 U.S.A.

P47B4C - Rev: 03/28/2002

Warranty ..................................................... 2

Safety Instructions ..................................... 2

Pre-Assembly Instructions ......................... 4

Hardware, Parts Diagram and Lists ..... 5

Assembly Instructions ................................. 9

Lighting Instructions .................................. 14

Cleaning and Maintenance Instructions .... 16

Frequently Asked Questions .................. 18

Cooking Instructions ................................ 19

,/!X,WARNING

Combustion byproducts produced when using this product contain chemicals known to the

State of California to cause cancer, birth defects, or other reproductive harm.

Z_ WARNI NG

Failure to comply with these instructions

could result in a fire or explosion that could cause serious bodily injury, death, or

property damage.

Cooking Guide and Recipes ................ 20

Full 1-Year Warranty on Grill

For one year from the date of purchase Sears will repair or replace, at our option, any grill part

(except for paint loss, rusting and ignitor battery) that is defective in material or workmanship.

Limited Warranty on Selected Grill Parts

From one year after the date of purchase for the designated time periods listed below, Sears will replace the following grill parts if they are defective in material or workmanship. You wilt be charged for

labor.

• Lifetime of Grill: Aluminum Castings (except for paint loss)

• 1 Year: Cast Iron Burners

• 2 Years: All Other Grill Parts (except flame tamers, cooking grids and ignitor battery)

Warranty Service Warranty service is available by contacting the ®

nearest Sears Service Center at 1-800-4-MY-HOME

Z_ WARNI NG

Your grill will get very hot. Never lean over the cooking area while using your grill. Do not touch cooking surfaces, grill housing, Lid or any other grill parts while the grill is in operation, or

until the grill has cooled down after use.

Failure to comply with these instructions may result in serious bodily injury.

FOR YOUR SAFETY

1. Do not store or use gasoline or other flam- mable material and liquids in the vicinity of this

or any other appliance.

2. An LP cylinder not connected for use shall not be stored in the vicinity of this or any other

appliance.

FOR YOUR SAFETY

If you smell gas:

1. Shut off gas to the appliance.

2. Extinguish any open flame.

3. Open Lid.

4. If odor continues, immediately call your gas supplier or your fire department.

Warranty Restrictions

• This warranty is void if grill is used for commer- cial or rental purposes.

• This grill is for use with Liquid Propane (LP) gas only. Any attempt to convert this grill to

natural gas is dangerous and will void your product warranty.

• This warranty applies only when the grill is

used in the United States.

• This warranty gives you specific legal rights, and you may also have other rights which vary

from state to state.

Sears, Roebuck and Co., Dept. 817WA,

Hoffman Estates, IL 60179

Grill Installation Codes

This gas grill must be installed in accordance with all local codes. In areas without local codes, follow the latest edition of the National Fuel Gas Code

ANSI Z223.1. In Canada, installation must conform

to standard CAN/CGA lb149.1 or 1-b149.2 (Installa- tion Code for Gas Burning Appliances and Equipment) and all local codes.

Correct LP Gas Tank Use LP gas grill models are designed for use with a

standard 20 lb. Liquid Propane Gas (LP gas) tank, not included with grill box. Never connect your gas grill to an LP gas tank that exceeds this capacity.

A tank of approximately 12 inches in diameter by

2 © Sears, Roebuck and Co.

18-1/2incheshighis themaximumsizeLPgas

tankto use.You must use an "OPD" gas tank

which offers an Overfill Prevention Device. This safety feature prevents the tank from being overfilted

which can cause malfunction of the LP gas tank, regulator and/or grill.

The LP gas tank must be constructed and marked in accordance with specifications of the U.S. Dept. of Transportation (DOT). In Canada, the LP gas tank must meet the Canadian Transportation and Communications (CTC) specifications. Also be sure

to read and follow all LP instructions below.

1. The LP gas tank has a shutoff valve,

terminating in an LP gas supply tank valve outlet, that is compatible with a Type 1 tank

connection device. The LP gas tank must also have a safety relief device that has a direct communication with the vapor space of

the tank.

2. The tank supply system must be arranged for vapor withdrawal.

3. The LP gas tank used must have a collar to protect the tank valve.

Proper Placement and Clearance of Grill Never use your gas grill in a garage, porch, shed,

breezeway or any other enclosed area. Your gas grill is to be used outdoors only, at least 24 inches from the

back and side of any combustible surface. Your gas grill should not be placed under any surface

that will burn. Do not obstruct the flow of ventilation air around the gas grill housing.

This outdoor gas grill is not intended to be installed in or on recreational vehicles and/or boats.

• Never connect an unregulated LP gas tank to your gas grill. The gas regulator assembly supplied with your gas grill is adjusted to have an outlet pressure of 11" water column (W.C.) for connection to an LP gas tank.

• Only use the regulator and hose assembly supplied with your gas grill. Replacement

regulators and hose assemblies must be those

specified by Sears.

• Have your LP gas tank filled by a reputable

propane gas dealer and visually inspected and re-qualified at each filling.

• Never fill the gas tank beyond 80% full.

Have your propane gas dealer check the release valve after every filling to ensure that it

remains free of defects.

• Always keep LP gas tanks in an upright

position.

• Do not store (or use) gasoline or other flammable vapors and liquids in the vicinity of this gas grill.

• An LP gas tank that is not connected for use must

NOT be stored on bottom shelf or in the vicinity of

this or any other gas grill.

• Do not subject the LP gas tank to excessive heat.

• Never store an LP gas tank indoors. If you store your gas grill in the garage or other indoor

location, always disconnect the LP gas tank

first and store it safely outside.

• LP gas tanks must be stored outdoors in a well-ventilated area and out of the reach of

children. Disconnected LP gas tanks must not

be stored in a building, garage or any other

enclosed area.

• When your gas grill is not in use the gas

must be turned off at the LP gas tank.

• The regulator and hose assembly must be

inspected before each use of the grill. If there is excessive abrasion or wear or if the hose

is cut, it must be replaced prior to the grill being used again.

• Keep the gas regulator hose away from hot grill surfaces and dripping grease. Avoid

unnecessary twisting of hose. Visually inspect

hose prior to each use for cuts, cracks, excessive wear or other damage. If the hose appears damaged do not use the gas grill.

Call Sears at 1-800-366-PART (1-800-366-7278) for a Sears authorized replacement hose.

Never light your gas grill with the lid closed

• or before checking to insure the burner tubes are fully seated over the gas valve orifices.

Never allow children to operate your grill. Do

• not allow children to play near your grill.

WARNI NG

A strong gas smell, or the hissing sound of gas indicates a serious problem with your gas grill or the LP gas tank. Failure to

immediately follow the steps listed below could result in a fire or explosion that could cause serious bodily injury, death, or prop- erty damage.

• Shut off gas supply to the gas grill.

• Turn the Control Knobs to OFF position.

• Put out any flame with a fire extinguisher.

• Open Grill Lid.

• Get away from the LP gas tank.

• Do not try to fix the problem yourself.

• If odor continues or you have a fire you cannot extinguish, call your fire

department.

Do not call near the LP gas tank because

your telephone is an electrical device and

could create a spark resulting in fire

and/or explosion.

NOTE: The normal flow of gas through the regulator and hose assembly can create a humming noise. A low volume of noise is perfectly normal and will not interfere with

operation of the grill. If humming noise is

loud and excessive you may need to purge air from the gas line or reset the regulator excess gas flow device. This purging proce- dure should be done every time a new LP gas tank is connected to your grill. For help with this procedure refer to page 15, step 4, or call the Customer Service Helpline for assistance, 8am - 8pm CST, Monday through

Friday 1-888-317-7642.

• Longnoseplierscanbe usedto remove CotterPinwhencleaningtheBurners

• Useworkglovestoprotectyourhands

• Weareyeprotection

• WhenyouhavefinishedassemblingyourGrill besureall PatternHeadThumbScrewsare

tightened.Youmayusethe suppliedTighten-

ingTool(P55M3A)asneeded.

To reducethechanceof "FLASH-BACK"(see CAUTIONat right)cleantheBurnerTubesand

Burnersbeforefullyassemblingyourgrill. RemovetheCotterPinfromtherearunderside

of eachBurnerusinga pairof tongnosepliers. Carefullylift eachBurnerupandawayfromthe GasValveOrifice,thenreferto Figure1 and

performoneofthesethreecleaningmethods:

1. Benda stiffwire,(alightweightcoathanger workswell)intoa smallhookasshown

below.Runthe hookthroughtheBurnerTube

andinsidetheBurnerseveraltimesto remove anydebris.

CAUTION: Spiders and small insects occa-

sionally spin webs or make nests in the grill

Burner Tubes during transit and warehousing.

These webs can lead to a gas flow obstruc- tion which could result in a fire in and around

the Burner Tubes. This type of fire is known as a "FLASH-BACK" and can cause serious

damage to your grill and create an unsafe operating condition for the user.

Although an obstructed burner tube is not the only cause of "FLASH-BACK', it is the most

common cause. To reduce the chance of "FLASH-BACK", you

must clean the burner tubes before assem- bling your grill, and at least once a month in

late summer or early fall when spiders are most active. Also perform this Burner Tube

cleaning procedure if your grill has not been

used for an extended period of time.

t[ _,,

2. Use a bottle brush with a flexible handle. Run the brush through the Burner Tube and inside the Burner several times, removing any

debris.

3. Use an air hose to force air through each Burner Tube. The forced air should pass

debris or obstructions through the Burner and out the Ports.

Figure 1

SPARK ELECTRODE AS- / BURNER BURNER PORT

z WARNING

The location of the Burner Tube with re- spect to the Orifice is vital for safe

operation. Check to ensure the Orifice is inside of the Burner Tube before using your gas grill. See Fig. 2. If the Burner Tube

does not fit over the Valve Orifice, lighting the Burner may cause explosion and/or fire.

Figure 2

GAS VALVE ASSEMBLY

ORIFICE BURNER TUBE

GAS COLLECTOR BOX

TO CLEAN BURNER TUBE, ,................. , _ ................ o o o o o o o o o o _

INSERT HOOK__HERE _ -- '_

L_jL _Z" FOOT

BURNER TUBE COTTER PIN

The following table illustrates a breakdown of the hardware pack. It highlights what components are used in the various stages of assembly.

Ref.

H017 H019 H017 H024 H020

H018

H017

P8080A

Component Qty. to Use

1/4"xl/2" Pattern Head Screw 4 1/4"x2" Pattern Head Screw 8 1/4"xl/2" Pattern Head Screw 2

1/4"xl/2" Special Round Head Screw 2 1/4" Wing Nut

1/4"x3/4" Pattern Head Screw

1/4"xl/2" Pattern Head Screw

AA Battery

Actual Size and Quantity of Each Hardware Piece:

Purpose of Components

Attaches Foldable Cart Legs Attaches Cart Legs To Bottom Shelf Attaches Tank Holder To Bottom Shelf

Attaches Tank Hook To Grill Head

Attaches Side Shelf and Side Burner To Grill Head

Attaches Spice Basket To Side Shelf

Powers The Electric Ignitor

1/4"x2" Pattern Head Screw

Qty. 8

Ref. # H019

1/4"xl/2" Pattern Head Screw

Qty. 10

Ref. # H017

AA Battery Qty. 1

Ref. # P8080A

1/4"xl/2" Special Round Head

Screw Qty. 2

Ref. # H024

1/4"x3/4" Pattern Head Screw Qty. 8

Ref. # H018

1/4" Wing Nut Qty. 2 Ref. # H020

The following table illustrates a breakdown of the hardware pack. It highlights what components are used

in the various stages of assembly.

Ref. Component Qty. to Use

P55F5A Customized Wrench 1

P5540B Manual Lighting Stick 1

H025 M4x8mm Pattern Head Screw 1

P55M3A Tightening Tool 1

Actual Size and Quantity of Each Hardware Piece:

Customized Wrench Qty. 1

Ref. # P55F5A Scale 1:0.6

Purpose of Components

Tighten Caster Attaches To Bowl Support Bracket - Left Attaches To Bowl Support Bracket - Left

Allows you to tighten Pattern Head Thumb Screws as needed

Tightening Tool M4x8mm Pattern Head Screw Qty. 1 Qty. 1

Ref. # P55M3A Ref. # H025

Manual Lighting Stick

Qty. 1 Ref. # P5540B

Ref. Component Qty. to Use

P3430A Control Knob 1 P55L7A Cotter Pin 1

H025 M4x8mm Pattern Head Screw 2 H027 M4 Plain Washer 2

Actual Size and Quantity of Each Hardware Piece:

Purpose of Components Install To Side Burner Valve Stem

Secure To Side burner Attaches To Side Burner Valve Bracket

Attaches To Side Burner Valve Bracket

M4x8mm Pattern Head Screw M4 Plain Washer

Qty. 2 Qty. 2

Ref. # H025 Ref. # H027

Control Knob Cotter Pin Qty, 1 Qty. 1

Ref. # P3430A Ref. # P55L7A

8b 9

REF# DESCRIPTION PART# QTY

REF#

DESCRIPTION PART#

QTY

1. Lid- Porcelain P0179A 1

2. Lid Side Panel - Left P0180A 1

3. Lid Side Panel- Right P0181A 1

4. Temperature Gauge P0616C 1

5. Round Lid Handle P0257A 1

6. Heat-Insulating Spacer P55JIA 2

7. Name Plate P0468A 1 8a. Third Cooking Rack P1533A 1 8b. Secondary Cooking Rack P1532A 1

9. Cooking Grid P1657A 2

10. Flame Tamer P1743A 2

11. Main Burner P1955A 3

12. Main Burner Bracket P2237A 1

13. Gas Collector Box & Electrode P2618F 2

14. Ignition Wire Set P2646A 1

15. Electric Ignitor P2503G 1

16. Bowl Side Panel - Left P0782A 1

17. Bowl Side Panel- Right P0783A 1

18. Bowl Front Panel P0784A 1

19. Bowl Rear Panel P0785A 1

35.

Caster P5118A Customzied Wrench P55F5A

35a.

Caster Seat P4528A

36.

37.

Tank Hook P4037A Tank Holder P4037B

38.

39.

Side Burner Lid P0192A

40.

Pot Support P80F7A

41. Side Burner Electrode P2627A

42. Side Burner P1958A

43. Gas Valve for Side Burner P32D5A

44. Connection Tube P3983D

45. Regulator with Hose P3632L

46. Manual Lighting Stick P5540B

47. Heat Shield for Grease Tray P80P7A

48. Tightening Tool P55M3A

--- Owner's Manual P47B4C

--- Hardware Pack P55K4A

--- Hardware Pack A P55L3B

--- Hardware Pack B P55K5C

4 1 4 1 1

1 1 1

1 1 1 1

1 1 1 1 1 1

20. Grease Draining Tray P2744A 1

21. Grease Receptacle P2741B 1

22. Gas Manifold P5046A 1

23. Gas Valve for Main Burner P32CID 3

24. Heat Shield for Control Panel P2984A 1

25. Control Panel P2985A 1

26. Control Knob P3430A 4

27. Side Shelf- Left P1160A 1

28. Side Burner Frame P1167A 1

29. Spice Basket P5215A 2

30. Bottom Shelf P1064A 1

31. Bowl Support Bracket - Left P1342A 1

32. Bowl Support Bracket - Right P1342B 1

33. Cart Leg - Right P0848A 2

34. Cart Leg - Left P0941A 2

For the repair or replacement parts you need: Call 6 am - 11 pm CST, 7 days a week

1-8 00-366-PART (1-800-366-7278)

To make sure you obtain the correct replacement

parts for your Kenmore gas grill, please refer to

the part numbers on this page. The following

information is required to assure you receive the

correct parts:

1. Grill Model Number (see CSA label on grill)

2. Part Number

3. Part Description

4. Quantity of parts needed

Important: Keep this Owner's Manual for convenient referral and for part replacement.

Important: Use only Sears authorized parts. The use of any part that is not Sears authorized can be dangerous and will also void your product

warranty.

CAUTION:Whileitispossibleforonepersonto

assemble this grill, obtain assistance from another person when handling some of the larger, heavier pieces, espe- cially the grill head.

1. Open Lid of shipping carton and remove top sheet of cardboard. Lay cardboard sheet on floor and use as a

work surface to protect floor and grill parts from scratches.

2. Remove packing materials and cart parts from shipping carton.

3. You may slice the carton front corners with a utility knife to lay open the carton front panel. This wilt

allow you to raise the grill head Lid and remove the components packed inside the head, making it easier to lift.

4. With an assistant, lift the grill head out of the ship- ping carton and place it on the cardboard work sur-

face. See Fig. 1.

5. Use the parts list to check that all parts have been included.

6. Inspect the grill for damage as you assemble it. Do not assemble or operate the grill if it appears

damaged. If there are damaged or missing parts when you unpack the shipping box, or you have questions during the assembly process, call:

1-888-317-7642

8 a.m. - 8 p.m CST, Mon. - Fri.

Figure 2

CART LEG-RIGHT

Figure 3

BOTTOMSHELF

HOLES FOR TANK HOLDER

CARTLEG-LEFT

e,/-j

GRILL HEAD

CARTLEG-LEFT

Assembling The Cart To The Grill Head

1. Lay the Grill Head flat on its back as shown in

Fig. 2. Unfold the 4 pre-assembled Cart Legs as shown in Fig. 2. Tighten securely using 4 of the 1/4"xl/2" Pattern Head Screws provided.

2. Before attaching the Bottom Shelf to the Cart Legs be sure the holes for the Tank Holder on Bottom Shelf are located on the right.

3. Install the Bottom Shelf between the Cart Legs.

Align the holes on Cart Legs with the threaded

holes at the corners of Bottom Shelf. Tighten securely using 8 of the 1/4"x2" Pattern Head Screws provided. See Fig. 3.

4. Screw the 4 Casters into the Caster Seats (see bottom of Cart Legs). Turn the threaded Caster Stem

by hand, clockwise until it stops. Tighten securely by using the Customized Wrench provided. See Fig. 4.

Figure 1

IRILL HEAD

Figure 4

BOTTOM SHELF

CART LEG-RIGHT

GRILL HEAD

CASTER

CARTLEG-LEFT

CART LEG-RIGHT

GRILL HEAD

Be sure all 4 Casters are locked, then with the assistance of another person, turn the

assembled grill upright. See Fig 5. Install Tank Holder to right side of Bottom Shelf. Align

the holes on Tank Holder with the threaded holes on the side of Bottom Shelf. Tighten

securely using 2 of the 1/4"x1/2" Pattern Head Screws provided.

Attach the Tank Hook to the right side of Grill

Head as shown in Fig. 5. Align holes of Tank Hook with holes on the right side of Grill Head. Secure firmly using 2 of the 1/4"x1/2" Special Round Head Screws and 2 of the 1/4" Wing Nuts provided. Insert screws from inside Grill Head and attach Wing Nuts from outside of Tank Hook.

7. Position Heat Shield into slots in Grease

Draining Tray. From the back side of Grill Head install the

Grease Draining Tray and Heat Shield. See Fig. 5. The Heat Shield is reeuired to be

oresent and centered for vour safety.

9. Install the Grease Receptacle under Grease

Draining Tray. See Fig. 5.

Installing Manual Lighting Stick

1. Attach the Manual Lighting Stick to the Left Bowl Support Bracket as shown in Fig. 5a.

Align the hole at the end of Manual Lighting

Stick Wire with the threaded hole on the Left Bowl Support Bracket. Tighten securely using

the M4x8mm Pattern Head Screw packed with the Manual Liqhtinq Stick.

Figure 5a

Figure 5

GRILL HEAD

Figure 6

BOWL SUPPORT BRACKET-LEFT

HEAT SHIELD

SIDE SHELF FRAME

GREASE RECEPTACLE

GREASE DRAINING

TRAY

TANK HOLDER

GRILL HEAD

SIDE BURNER FRAME

M4x8mm PATTERN

HEAD SCREW _/_"

MANUAL BOWL SUPPORT LIGHTING BRACKET-LEFT

Installing Side Shelf and Side Burner

Remove Side Burner from Side Burner Kit before installing.

Enlisting the aid of an assistant, attach Side Burner Frame to right side of grill. Attach Side Shelf Frame to left side of grill as shown in Fig. 6. Be sure the holes for the Spice Baskets appear on the front side of the grill. Align the 4 holes

on Side Shelf Frame and Side Burner Frame with the threaded holes on left and right Bowl Support

Brackets. Tighten securely using 4 of the 1/4"x3/ 4" Pattern Head Screws provided.

Burner Frame. See Fig. 6a.

Figure 6a

M4x8mm PATTERN HEAD SCREW

AND WASHER

BOWL SUPPORT BRACKET-RIGHT

HOLES FOR SIDE BURNER VALVE KIT

SIDE BURNER

FRAME

;EMBLED

VALVE KIT

IRNER

VALVE BRACKET2. Install the Pre-assembled Valve Kit to the Side

+ 21 hidden pages

Kenmore 14115223 Owner’s Manual

Specifications and Main Features

Frequently Asked Questions

User Manual