Kenmore 110.C69672*, 110.C69682*, 110.C69692* Quick Reference Guide

Quick Start Dryer Guide

We have taken great care to give your new dryer the most convenient and easy-to-use features. Use this guide to help optimize the use of your dryer.
Consult the Use and Care Guide for more detailed instructions. To contact the Sears Service Center, call 1-800-4-MY-HOME®(1-800-469-4663).

Models/Modèles 110.C69672✼, C69682✼, C69692✼

START

Clean the lint screen.

Place laundry in dryer.
Shut the door.
SelectAuto Moisture Sensing Cycle,

• Turn cycle knob to recommended Auto Moisture
Sensing Cycle for type of load being dried.

• Use Normal Dry to dry most heavy to medium-weight
fabrics.

or Timed Dry Cycle.

• Turn cycle knob to a Timed Dry Setting.

• Select temperature setting using Fabric Care selector.

Select the End of Cycle Signal.
Press and hold the START button.

W10035740A

END OF CYCLE SIGNAL CONTROL

The End of Cycle Signal sounds when a cycle

is complete. This signal is helpful when you are

drying permanent press, synthetics, and other
items that should be removed from the dryer
promptly at the end of a cycle.

The End of Cycle Signal is selectable. The signal
stops when you open the door or turn the End of
Cycle Signal on the Start button to Off.

If the WRINKLE GUARD
Cycle Signal sounds every few minutes. If the End
of Cycle Signal is turned off, you will not hear
WRINKLE GUARD

®

feature is on, the End of

®

sound every few minutes.

Continued on back

FABRIC CARE CONTROL

For models with a Fabric Care control knob, you may use this control to select the drying temperature that matches the fabrics

in your load. The following table lists suggested auto moisture sensing or timed dry settings for various loads. This is only a guide.

ABRIC CARE/ AUTO MOISTURE TIMED DRY

F

EMPERATURE LOAD TYPE SENSING SETTING*

T

COTTON/TOWELS Heavyweight items – quilts, towels, More Dry 50-70
HIGH jeans, cottons, bedspreads minutes

NORMAL Medium-weight items – shirts, Normal Dry 30-50
MEDIUM HIGH sheets, slacks, play clothes, minutes

DELICATE Lightweight items – lingerie, blouses, Less Dry 20-40
LOW dresses, synthetics, and blends minutes

CASUAL Medium-weight items – synthetics Normal Dry 30-50
MEDIUM (polyester, acrylic), skirts, sweaters, slacks minutes

*Reset time as needed to allow items to dry completely.

cloth diapers

CYCLE SELECTOR (TIMER) CONTROL

Auto Moisture Sensing

When you are using theAuto Moisture Sensing Cycle,
the dryness of the load is determined by two metal strips
(sensors) located on the inside of the dryer. The metal
strips help “feel” the amount of moisture left in the clothes
as they pass. When there is moisture left in the clothes, the
Cycle Control knob will not advance. As clothes begin to
dry, the amount of water left in the clothes decreases, and
the timer advances through the remainder of the cycle.
When the selected dryness level is reached, the dryer
goes into a cool down period of up to 10 minutes.

If the load is drier than you like, you may select a setting
closer to Less Dry the next time you dry a similar load. If
a load is not as dry as you like, you may complete drying
using a Timed cycle. You may also select a setting closer
to More Dry the next time you dry a similar load.

Timed Dry

This cycle may be used to get up to 80 minutes of heated
drying time. The heating cycle is followed by a cool down period
of up to 10 minutes.

Air Dry

You may use the Air Dry cycle to get up to 30 minutes of drying
time in room temperature air. This setting should be used for
items such as plastics, rubber, and heat-sensitive fabrics.

WRINKLE GUARD®I

WRINKLE GUARD®I helps smooth out wrinkles that may form when clothes are not removed promptly at the end of a cycle.

WRINKLE GUARD®I continuously tumbles the load, without heat, for 40 minutes unless you open the dryer door.

During WRINKLE GUARD

®

I, the End of Cycle Signal will sound every 5 minutes unless the signal is turned off.

TROUBLESHOOTING – LONG DRY TIMES, LOAD NOT DRYING

Before you call service...check for the following.

Is the lint screen clogged with lint?

• Clean the lint screen before each load.

W10035740A

© 2008 Sears Brands, LLC

Is the exhaust vent or outside exhaust hood clogged with
lint?

• Lint should be cleaned out of the exhaust vent at least once
every 2 years.

See the Use and Care Guide for complete details.

®

Registered Trademark /TMTrademark /SMService Mark of

Sears Brands, LLC, used under licensee by Sears Canada Inc.

Printed in U.S.A.

10/08