Kenmore 110.C6732, 110.C6733, 110.C6734* Quick Reference Guide

Continued on back

W10035660

Quick Start Dryer Guide

We have taken great care to give your new dryer the most convenient and easy-to-use features. Use this guide to help optimize the use of your dryer.
Consult the Use and Care Guide for more detailed instructions. To contact the Sears Service Center, call 1-800-4-MY-HOME®(1-800-469-4663).

Models/Modéles 110.C6732, C6733, C6734✼

START

Clean the lint screen.

Place laundry in dryer.
Shut the door.
Select Auto Dry Cycle,

• Turn cycle knob to recommended Auto Dry Cycle for
type of load being dried

• Use Normal Dry to dry most heavy to medium-weight
fabrics

or Timed Dry Cycle.

• Turn cycle knob to Timed Dry

Press and hold the PUSH TO START button.

WARNING

Explosion Hazard

Keep flammable materials and vapors, such as
gasoline, away from dryer.

Do not dry anything that has ever had anything
flammable on it (even after washing).

Failure to follow these instructions can result in
death, explosion, or fire.

WARNING

Fire Hazard
No washer can completely remove oil.
Do not dry anything that has ever had any type of

oil on it (including cooking oils).
Items containing foam, rubber, or plastic must be

dried on a clothesline or by using an Air Cycle.
Failure to follow these instructions can result in

death or fire.

W10035660

7/06

© 2006 Sears Brands, LLC

®

Registered Trademark / TMTrademark / SMService Mark of Sears Brands, LLC

Printed in U.S.A

CYCLE SELECTOR (TIMER) CONTROL

Auto Dry

During the Auto Dry Cycle, the exhaust air temperature of
the dryer determines the drying time and dryness levels. A
thermostat signals the Cycle Control knob when to move
into cool down. The drying time for an Auto Dry Cycle
depends on load type and load size. When drying a large
or heavy load, the Cycle Control knob may take a long
time before it begins to advance into cool down. The Auto
Dry Cycle takes the guesswork out of drying time and
enhances fabric care. The amount of time that is displayed
is the estimated time remaining in the cycle.

The Automatic Cycle may be used for most lightweight
loads. Drying time varies according to the type of fabric,
size of the load, and dryness setting.

Dryness is determined by the exhaust temperature
of the dryer. When the dryness selected is reached, the
dryer goes into a 5 minute (approximately) cool down
period.

The Cycle Selector (Timer) Control may be set to NORMAL
DRY, which is good for most fabrics. At the end of the cycle, you
may check the dryness of the load.

If the load is drier than you like, you may select a setting closer
to Less Dry the next time you dry a similar load.

If a load is not as dry as you like, you may complete drying
using a Timed cycle. You may select a setting closer to More
Dry the next time you dry a similar load.

Timed Dry

This cycle may be used to get up to 70 minutes of heated
drying time. The heating cycle is followed by a cool down period
of up to 10 minutes.

Air Dry

You may use the Air Dry cycle to get up to 20 minutes of drying
time in room temperature air. This setting should be used for
items such as plastics, rubber and heat-sensitive fabrics.

FABRIC CARE/TEMPERATURE CONTROL

The following table lists suggested auto dry or timed dry settings for various loads. This is only a guide.

TEMPERATURE

LOAD TYPE

CYCLE SETTING

TIMED DRY
SETTING*

HIGH Heavyweight items – Quilts, towels,

jeans, cottons, bedspreads

Timed Dry

40-70
minutes

LOW Lightweight items – Lingerie, blouses,

dresses, synthetics and blends

Auto Dry

N/A

*Reset time as needed to allow items to dry completely.

TROUBLESHOOTING – LONG DRY TIMES, LOAD NOT DRYING

Is the lint screen clogged with lint?

• Clean the lint screen before each load.

Before you call service...check for the following.

Is the exhaust vent or outside exhaust hood clogged with
lint?

• Lint should be cleaned out of the exhaust vent at least once
every 2 years.

See the Use and Care Guide for complete details.