Kenmore 11088752794, 11088752793, 11080754002, 11080754001 Owner’s Manual

24-Inch Wide LAUNDRY CENTER

Washer- Electric Dryer

CENTRO DE LAVANDERIA de 24 pulg. (61 cm) de ancho

Lavadora - Secadora el_ctrica

3979332A Sears Roebuck and Co., Hoffman Estates, IL 60179 U.S.A. www.sears.com

TABLE OF CONTENTS

WE SERVICE WHAT WE SELL ...................................................... 3

WARRANTY ..................................................................................... 3

WASHER/DRYER SAFETY ............................................................ 4

INSTALLATION INSTRUCTIONS .................................................. 5

Tools and Parts ............................................................................ 5

Alternate Parts .............................................................................. 5

Location Requirements ............................................................... 5

Drain System ................................................................................ 6

Electrical Requirements ................................................................ 7

Electrical Connection ................................................................... 8

Venting Requirements ............................................................... 12

Install Leveling Legs .................................................................. 13

Remove Foam Packing ............................................................. 13

Connect Drain Hose .................................................................. 13

Connect Inlet Hoses .................................................................. 14

Secure Drain Hose .................................................................... 14

Plan Vent System ...................................................................... 15

Install Vent System .................................................................... 16

Level Laundry Center ................................................................ 16

Connect Vent ............................................................................. 17

Complete installation ................................................................. 17

FEATURES AND BENEFITS ....................................................... 17

DUAL-ACTION TM Plus Agitator ................................................. 17

Porcelain Wash Basket ............................................................. 17

4-way Venting ............................................................................ 17

WASHER USE .............................................................................. 18

Starting Your Washer ................................................................ 18

Cycles ........................................................................................ 19

Rinse and Spin .......................................................................... 19

Drain and Spin ........................................................................... 19

Understanding Washer Cycles .................................................. 19

Normal Sounds .......................................................................... 20

LAUNDRY TIPS ............................................................................ 20

Loading ...................................................................................... 20

DRYER USE ................................................................................. 21

Starting Your Dryer .................................................................... 21

Stopping and Restarting ........................................................... 21

Loading ...................................................................................... 22

Drying, Cycle and Temperature Tips ........................................ 22

Cycles ........................................................................................ 22

LAUNDRY CENTER CARE ......................................................... 23

Cleaning Your Washer ............................................................... 23

Water inlet Hoses ...................................................................... 23

Cleaning the Lint Screen ........................................................... 23

Cleaning the Dryer interior ........................................................ 24

Removing Accumulated Lint ..................................................... 24

Vacation, Storage, and Moving Care ........................................ 24

TROUBLESHOOTING WASHER ................................................ 25

TROUBLESHOOTING DRYER .................................................... 27

WE SERVICE

WARRANTY

WHAT WE SELL

Your purchase has added value because you can depend on Sears HomeCentral ®for service. With over 12,000 trained repair

specialists and access to over 4.2 million parts and accessories, we have the tools, parts, knowledge and skills to ensure our

pledge: We Service What We Sell.

Sears Maintenance Agreements

Your Kenmore ®appliance is designed, manufactured and tested to provide years of dependable operation. Yet any major

appliance may require service from time to time. The Sears

Maintenance Agreement offers you an outstanding service program, affordably priced.

The Sears Maintenance Agreement

• Isyour way to buy tomorrow's service at today's price.

• Eliminates repair bills resulting from normal wear and tear.

• Provides for non-technical and instructional assistance.

• Even if you don't need repairs, provides an annual Preventive Maintenance Check, at your request, to ensure that your

appliance is in proper running condition.

Some limitations apply. For more information, call

1-800-827-6655.

Full One-Year Warranty on Mechanical and Eleckical Parts

For one year from the date of purchase, when this laundry center

is installed and operated according to the instructions provided in this Use and Care Guide, Sears will repair this laundry center, free of charge, if defective in material or workmanship.

NOTE: Exhausting your laundry center with a plastic vent can void this warranty. See "Installation Instructions" for the complete exhaust requirements for this laundry center.

Limited Five-Year Warranty on Gearcase Parts

For the second through fifth years from the date of purchase, Sears will replace any gearcase parts that are defective in material or workmanship. You will be charged for labor after the first year.

Limited Ten-Year Warranty on Plastic Tub

For the second through tenth years from the date of purchase, Sears will replace the plastic tub if defective in material or workmanship. You will be charged for labor after the first year.

Warranty Restriction

If the laundry center is subject to other than private family use, the above warranty coverage is effective for only 90 days.

Warranty Service Warranty service is available by contacting the nearest Sears

Service Center. This warranty applies only while the product is in

use in the United States. This warranty gives you specific legal rights and you may also

have other rights which vary from state to state.

For Sears warranty information or to contact a Sears Service Center, please reference the service numbers located on the

back page of this manual.

Sears, Roebuck and Co.

D/817WA, Hoffman Estates, IL 60179

Product Record

In the space below, record your complete model number, serial

number, and purchase date. You can find this information on the model and serial number label, located at the top inside dryer

door well.

Have this information available to help you quickly obtain assistance or service when you contact Sears concerning your appliance.

Model number

Serial number

Purchase date

Save these instructions and your sales receipt for future reference.

WASHER/DRYER SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.

This symbol alerts you to potential hazards that can kill or hurt you and others. All safety messages will follow the safety alert symbol and either the word "DANGER" or

This is the safety alert symbol. "WARNING." These words mean:

You can be killed or seriously injured if you don't immediately follow instructions.

You can be killed or seriously injured if you don't follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

IM PORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of fire, electric shock, or injury to persons when using the washer/dryer, follow

basic precautions, including the following:

Read all instructions before using the washer/dryer. Do not place items exposed to cooking oils in

your dryer. Items contaminated with cooking oils may contribute to a chemical reaction that could

cause a load to catch fire. Do not wash or dry articles that have been previously

cleaned in, washed in, soaked in, or spotted with gasoline, dry-cleaning solvents, other flammable, or explosive substances as they give off vapors

that could ignite or explode.

• Do not add gasoline, dry-cleaning solvents, or other flammable, or explosive substances to the wash water.

These substances give off vapors that could ignite or

explode.

• Do not allow children to play on or in the washer/dryer. • Close supervision of children is necessary when

the washer/dryer is used near children.

• Before the washer/dryer is removed from service or dis- • carded, remove the doors to the washer/dryer compart-

ments.

• Do not reach into the washer/dryer if the tub, agitator or drum is moving.

• Do not install or store the washer/dryer where it will be exposed to the weather.

• Do not tamper with controls.

• Clean dryer lint screen before or after each load.

Under certain conditions, hydrogen gas may be

produced in a hot water system that has not been used for 2 weeks or more. HYDROGEN GAS IS

EXPLOSIVE. If the hot water system has not been used for such a period, before using the washing

machine, turn on all hot water faucets and let the water flow from each for several minutes. This will

release any accumulated hydrogen gas. As the gas is flammable, do not smoke or use an open flame during this time.

Do not repair or replace any part of the washer/dryer or attempt any servicing unless specifically recom- mended in this Use and Care Guide or in published user-repair instructions that you understand and have

the skills to carry out.

Do not use fabric softeners or products to eliminate static unless recommended by the manufacturer of

the fabric softener or product.

Do not use heat to dry articles containing foam rubber or similarly textured rubber-like materials.

Keep area around the exhaust opening and adjacent surrounding areas free from the accumulation of lint,

dust, and dirt.

• The interior of the machine and dryer exhaust vent should be cleaned periodically by qualified service personnel.

• See "Electrical Requirements" section for grounding instructions.

SAVETHESEINSTRUCTIONS

INSTALLATION

INSTRUCTIONS

Check that you have everything necessary for correct installation.

Proper installation is your responsibility.

Parts listed are available from your local Sears store or Sears Service Center. For more information, please reference the service numbers located on the back page of this manual.

If You Have You Will Need to Buy

Laundry tub or Sump pump system (if not already standpipe taller available) than 96 in. (2.4 m)

Tools needed:

• #2 Phillips and flat-blade • Knife screwdriver

• Adjustable wrench that opens to 1 in. (2.5 cm) or • Duct tape

%6 in. open-end wrench • Caulking gun and

(for adjusting dryer feet) compound (for installing

• Level new exhaust vent)

• % in. nut driver or socket • Gloves

wrench • Pliers

• Wood block(for leveling) • Scissors

• Ruler or measuring tape • Tin snips (for new vent

• Wire stripper (direct wire installations) installations)

Parts supplied

Remove parts package from the washer basket. Check that all parts were included.

• Safety glasses

1 in. (2.5 cm) 2 in. (5 cm) diameter to 1 in. (2.5 cm) diameter diameter standpipe adapter, Part standpipe Number 3363920

Overhead sewer Standard 20 gal. (76 L) 34 in. (86.4 cm)

tall drain tub or utility sink and sump

pump (available from local plumbing suppliers)

Floor drain Siphon break, Part Number 285320,

additional drain hose, Part Number 285702 and connector kit,

Part Number 285442

Drain hose too Drain hose, Part Number 285664 and short connector kit, Part Number 285442

Lint clogged drain Drain protector, Part Number 367031

Water faucets 2 longer water fill hoses:

beyond reach of 6 ft (1.8 m) Part Number 76314, fill hoses 10 ft (3.0 m) Part Number 350008

tL,}0St ©_'1_,@(;_,, Y@'_SX?Yl1:,S

5 6 7

1. Water inlet hoses (2)

2. Intet hose flat washers (4)

3. Rear leveling legs (2)

4. Front leveling legs (2)

Parts needed:

Check local codes, electrical supply and venting, and read

"Electrical Requirements" and "Venting Requirements" before purchasing parts.

Mobile home installations require:

• Metal exhaust system hardware available for purchase from your local Sears store or Sears Service Center.

5. Plastic strap

6. Drain hose

7. Yellow, single wire hose clamp

8. Silver, double-wire hose clamp

Explosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from dryer.

Failure to do so can result in death, explosion,

or fire.

You will need

• A location that allows for proper exhaust installation. See "Venting Requirements."

• A separate 30 amp circuit.

• A grounded electrical outlet located within 2 ft (61 cm) of

either side of the laundry center. See "Electrical

Requirements."

• A sturdy floor to support the laundry center weight (laundry

center, water and load) of 500 Ibs (226.8 kg).

Alevelfloorwithamaximumslopeof1in.(2.5cm)under

entire laundry center. Clothes may not tumble properly and automatic sensor cycles may not operate correctly if dryer is

not level. Installing on carpet is not recommended.

A water heater set to deliver 120°F (49°C) water to the washer.

• Hot and cold water faucets located within 4 f1 (1.2 m) of the hot and cold water fill valves, and water pressure of 5-100 psi

(34.5-689.6 kPa).

Install the laundry center where it is protected from water and/or

weather.

Do not operate your washer in temperatures at or below 32°F (O°C). Some water can remain in the washer and can cause damage in low temperatures. See "Vacation, Storage, and

Moving Care" for winterizing information.

Do not operate your dryer at temperatures below 45°F (7°C). At

lower temperatures, the dryer might not shut off at the end of an automatic cycle. This can result in longer drying times.

Check code requirements. Some codes limit, or do not permit,

installation of the laundry center in garages, closets, mobile

homes, or sleeping quarters. Contact your local building

inspector.

Installation Clearances The location must be large enough to fully open the dryer door.

Laundry Center Dimensions

• Rear clearance may be 0 in. when house exhaust system is lined up directly with dryer exhaust.

48,=

ooo oo

3'_.ec_

o'_-l-_'h'_-l._o'_ i'I_,'_

Io=I)(Im,_) loc_ ll.!i_)llm.21_)

7 2

1, Recessed Area

2. Side view - closet or confined area

3. Closet door with vents

_4=,,)

Mobile Home-Additional Installation Requirements

This laundry center is suitable for mobile home installations. The installation must conform to the Manufactured Home

Construction and Safety Standard, Title 24 CFR, Part 3280 (formerly the Federal Standard for Mobile Home Construction and Safety, Title 24, HUD Part 280).

Mobile home installations require:

• Metal exhaust system hardware which is available for purchase from your local Sears store or Sears Service Center.

Special provisions must be made in mobile homes to

introduce outside air into the dryer. The opening (such as a nearby window) should be at least twice as large as the dryer

exhaust opening.

*Most installations require a minimum 51_ in. (14 cm) clearance

behind the dryer for the exhaust vent with elbow. See "Venting Requirements."

Minimum installation spacing for recessed area or closet

installation

The following dimensions shown are for the minimum spacings allowed.

• Additional spacing should be considered for ease of installation and servicing.

Additional clearances might be required for wall, door and floor moldings.

Additional spacing of 1 in. (2.5 cm) on all sides of the dryer is recommended to reduce noise transfer.

For closet installation, with a door, minimum ventilation

openings in the top and bottom of the door are required.

Louvered doors with equivalent ventilation openings are

acceptable.

The laundry center can be installed using the standpipe drain system (floor or wall), the laundry tub drain system, or the floor drain system. Select the drain hose installation method you need (see "Alternate Parts").

Standpipe drain system - wall or floor (view I & 2) The standpipe drain requires a minimum diameter standpipe of 2

in. (5 cm). The minimum carry-away capacity can be no less than 17 gal. (64 L) per minute. A 2 in. (5 cm) diameter to 1 in. (2.5 cm)

diameter standpipe adapter kit is available. See "Alternate Parts." The top of the standpipe must be at least 39 in. (99 cm) high and

no higher than 96 in. (2.4 m) from the bottom of the washer.

1 2

Laundry tub drain system (view 3)

The laundry tub needs a minimum 26 gal. (76 L) capacity. The top of the laundry tub must be at least 34 in. (86.4 cm) above the floor and no higher than 96 in. (2.4 m) from the bottom of the washer.

Floor drain system (view 4)

The floor drain system requires a siphon break that may be

purchased separately. (See "Alternate Parts.")

The siphon break must be a minimum of 28 in. (71 cm) from the

bottom of the washer. Additional hoses might be needed.

The wires that connect to the dryer must end in ring terminals or spade terminals with upturned ends.

If your outlet looks like this:

4-wire receptacle (14-30R)

Then choose a 4-wire power supply cord with ring or spade terminals and UL approved strain relief. The 4-wire power supply

cord must have 4, 10 gauge solid copper wires and match a 4- wire receptacle of NEMA Type 14-30R. The ground wire (ground

conductor) may be either green or bare. The neutral conductor must be identified by a white cover.

If your outlet looks like this:

It is your responsibility

• Tocontact a qualified electrical installer.

• To be sure that the electrical connection is adequate and in conformance with the National Electrical Code, ANSl/NFPA

70-latest edition and all local codes and ordinances. A copy of the above code standards can be obtained from:

National Fire Protection Association, Batterymarch Park,

Quincy, MA 02269.

• To supply the required 3 or 4 wire, single phase, 120/240-volt, 60-Hz., AC-only electrical supply (or 3 or 4wire, 120/208-volt electrical supply, if specified on the serial/rating plate) on a separate 30-ampere circuit, fused on both sides of the line. A time-delay fuse or circuit breaker is recommended. Connect

to an individual branch circuit. Do not have a fuse in the

neutral or grounding circuit.

• Do not use an extension cord.

• If codes permit and a separate ground wire is used, it is recommended that a qualified electrician determine that the ground path is adequate.

Electrical Connection

To properly install your laundry center, you must determine the type of electrical connection you will be using and follow the

instructions provided for it here.

• If local codes do not permit the connection of a cabinet ground connector to the neutral wire, see "Optional 3-wire

Connection."

• This laundry center is manufactured with a 3-wire, cabinet- ground conductor connected to the NEUTRAL (white or center wire) of the wiring harness at the terminal block.

• Use a 4-wire conductor cord when the laundry center is

installed in a mobile home or an area where local codes do not permit grounding through the neutral.

If using a power supply cord:

Dryer power supply cord must be:

• UL-listed

• Rated 120/240 volt minimum

• 30 amp

• Type SRD or SRDT

• At least 5 ft (1.52 m) long

3-wire receptacle (10-30R)

Then choose a 3-wire power supply cord with ring or spade terminals and UL approved strain relief. The 3-wire power supply cord, must have 3, No.-10 copper wires and match a 3-wire receptacle of NEMA Type 10-30R.

If connecting by direct wire:

Power supply cable must match power supply (4-wire or 3-wire)

and be:

• Flexible armored or non-metallic sheathed copper cable (with ground wire). All current-carrying wires must be insulated.

• 10 gauge solid copper wire (Do not use aluminum.)

• At least 5 ft (1.52 m) long.

GROUNDING INSTRUCTIONS

• For a grounded, cord-connected washer/dryer: This washer/dryer must be grounded. In the event of malfunc- tion or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current. This washer/dryer uses a cord having an equipment-

grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and

grounded in accordance with all local codes and ordinances.

• For a permanently connected washer/dryer: This washer/dryer must be connected to a grounded metal,

permanent wiring system, or an equipment-grounding con- ductor must be run with the circuit conductors and connected

to the equipment-grounding terminal or lead on the washer/dryer.

WARNING: Improper connection of the equipment-

grounding conductor can result in a risk of electric shock. Check with a qualified electrician or service representative or

personnel if you are in doubt as to whether the washer/dryer is properly grounded. Do not modify the plug on the power supply cord: if it will net fit the outlet, have a proper outlet in- stalled by a qualified electrician.

SAVE THESE INSTRUCTIONS

PowerSupplyCord DirectWire

FireHazard

UseanewULapproved30amppower

supplycord.

UseaULapprovedstrainrelief. Disconnectpowerbeforemakingelectrical

connections.

Connectneutralwire(whiteorcenterwire)to

centerterminal(silver).

Groundwire(greenorbarewire)mustbe

connectedto greengroundconnector.

Connectremaining2supplywiresto remaining

2terminals(gold). Securelytightenallelectricalconnections.

Failureto dosocanresultindeath,fire,or

electricalshock.

1. Disconnect power.

2. Remove the hold-down screw and terminal block cover.

FireHazard

Use10gaugesolidcopperwire. UseaULapprovedstrainrelief. Disconnectpowerbeforemakingelectrical

connections.

Connectneutralwire(whiteorcenterwire)to

centerterminal(silver).

Groundwire(greenorbarewire)mustbe

connectedto greengroundconnector.

Connectremaining2supplywiresto remaining

2terminals(gold). Securelytightenallelectricalconnections.

Failureto dosocanresultindeath,fire,or

electricalshock.

Assemble a ¾ in. (1.9 cm) UL approved strain relief (UL marking on strain relief) into the hole below the terminal block opening. Tighten strain relief screws just enough to hold the two clamp sections together. Put power supply cord through the strain relief, The strain relief should have a tight fit with the dryer cabinet and be in a horizontal position.

4. Now complete installation following instructions for your type of electrical connection:

n n ,,

1. Center silver-colored terminal-block screw

2. Hold-down screw

3. Terminal block cover

4. External ground connector

4-wire (recommended) 3-wire (if 4-wire is not available)

Electrical Connection Options

If your home has: And you will be Go to Section

connecting to:

4-wire receptacle A UL listed, 4-wire connection:

(NEMA Type 14-30R) 120/240 volt Power supply cord

1. Remove center terminal block screw.

2. Remove appliance ground wire (green with yellow stripes) from external ground connector screw. Fasten it under center,

silver colored terminal block screw.

amp., dryer

power supply

minimum, 30 cord*

4-wire direct A fused 4-wire connection:

circuit breaker disconnect or Direct Wire

box*

3-wire receptacle A UL listed,

(NEMA type 10-30R) 120/240 volt

3-wire connection: Power supply cord

amp., dryer

power supply

minimum, 30 cord*

3-wire direct A fused 3-wire connection:

disconnect or Direct Wire circuit breaker

box*

*If local codes do not permit the connection of a frame-grounding conductor to the neutral wire, go to "Optional 3-wire Connection"

section.

4-wire connection: Power supply cord

IMPORTANT: A 4-wire connection is required for all mobile

homes and where local codes do not permit the use of 3-wire

connections.

2 6

j'-- i€

1. Center silver-colored terminal block screw

2. Neutral grounding wire (green/yeilow)

3. External ground connector

3. Connect ground wire (green or bare) of power supply cord to

external ground conductor screw. Tighten screw.

4. Connect neutral wire (white or center wire) of power supply cord under center screw of the terminal block. Tighten screw.

5 4

5 7

1.4-wire receptacle (NEMA type 14-30R)

2. 4-prong plug

3. Ground prong

4. Neutral prong

5. Spade terminals with upturned ends

6. 3/4in. (!.9 cm) UL approved strain relief

7. Ring terminals

1. Neutral wire (white or center wire)

2. Center silver-colored terminal block screw

3. Neutral grounding wire (green/yellow)

4. Externa! ground connector

5. Green or bare wire of power supply cord

6. 3/4in. (1.9 cm) UL listed, strain relief

5. Connect the other wires to outer terminal block screws. Tighten screws.

6. Tighten strain relief screws.

7. Insert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold-down screw.

+ 19 hidden pages