Kenmore 110C81432510, 11081432510, 11081422510 Owner’s Manual

Use & Care Guide & Installation instructions Manual de uso y cuidado y las Instrucciones de instalaci6n

Guide d ut_l_sat_onet d entret_en et instructions pour I installation

English / Espa_ol / Franc;ais

Table of Contents..2

{ndJce...38

Table des mafi_res...74

Models/Modelos/Mod_les: 110.81422, 110.81432

re®

Wide

.entro

Lava

_entrede

Laveuse

P/N W10746859A Sears Brands Management Corporation

Hoffman Estates, IL 60179 U.S.A. www.ken more.corn

www.sears.com Sears Canada Inc.

Toronto, Ontario, Canada MSB 2B8 www.sears.ca

IGVGn

ry Center

GnC

TABLEOF CONTENTS

WASHER/DRYER SAFETY ...................................................... 3

iNSTALLATION iNSTRUCTIONS ............................................ 5

Tools and Parts ..................................................................... 5

Alternate Parts ...................................................................... 6

Location Requirements ........................................................ 6

Drain System ......................................................................... 7

Electrical Requirements - 240 Volt Models .................... 7

Electrical Requirements - 120 Volt Models ..................... 9

Electrical Connection - 240 Volt Models ...................... 10

Venting Requirements ........................................................ 16

Install Leveling Legs ........................................................... 17

Remove Foam Packing ...................................................... 17

Connect Drain Hose ........................................................... 17

Connect Inlet Hoses ........................................................... 18

Secure Drain Hose ............................................................. 19

Plan Vent System .............................................................. 20

Install Vent System ............................................................. 21

Connect Vent ...................................................................... 21

Level Laundry Center ........................................................ 22

Complete Installation ........................................................ 22

WASHER USE .......................................................................... 23

Control Panel and Features .............................................. 23

Starting Your Washer ........................................................ 23

Cycles ................................................................................. 24

Rinse and Spin ................................................................... 24

Drain and Spin .................................................................. 24

Understanding Washer Cycles ......................................... 25

Normal Sounds ................................................................... 25

LAUNDRY TiPS ........................................................................ 25

Loading ............................................................................... 25

DRYER USE ............................................................................... 26

Control Panel and Features .............................................. 26

Starting Your Dryer ........................................................... 27

Stopping and Restarting .................................................. 27

Loading .............................................................................. 27

Drying, Cycle, and Temperature Tips ............................. 27

Cycles .................................................................................. 28

LAUNDRY CENTER CARE ...................................................... 28

Cleaning the Laundry Center Location ........................... 28

Cleaning Your Washer ...................................................... 28

Water Inlet Hoses .............................................................. 28

Cleaning the Lint Screen ................................................... 29

Cleaning the Dryer Interior .............................................. 29

Removing Accumulated Lint ............................................. 29

Vacation, Storage, and Moving Care ............................. 29

TROUBLESHOOTING WASHER ............................................ 31

TROUBLESHOOTING DRYER ............................................... 35

PROTECTION AGREEMENTS ............................................... 37

WARRANTY ............................................................................. 37

SERVICE NUMBERS ................................................ Back Cover

WASHER/DRYER SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.

This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately follow instructions.

You can be killed or seriously injured if you don't follow

instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

WARNING - ...i.kofFi,o..

- Clothes dryer installation must be performed by a qualified installer.

- Install the clothes dryer according to the manufacturer's instructions and local codes,

- Do not install a clothes dryer with flexible plastic venting materials or flexible metal (foil type) duct. If flexible metal duct is installed, it must be of a specific type identified

by the appliance manufacturer as suitable for use with clothes dryers. Flexible venting materials are known to collapse, be easily crushed, and trap lint. These conditions will obstruct clothes dryer airflow and increase the risk of fire.

- To reduce the risk of severe injury or death, follow all installation instructions.

- Save these instructions.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of fire, electric shock, or injury to persons when using the washer/dryer, follow basic

precautions, including the following:

[] Read all instructions before using the washer/dryer. [] Do not place items exposed to cooking oils in your dryer.

Items contaminated with cooking oils may contribute to a

chemical reaction that could cause a load to catch fire.

[] Do not wash or dry articles that have been previously

cleaned in, washed in, soaked in, or spotted with gasoline, dry-cleaning solvents, other flammable, or explosive

substances as they give off vapors that could ignite or explode.

[] Do not add gasoline, dry-cleaning solvents, or other

flammable, or explosive substances to the wash water. These substances give off vapors that could ignite or explode.

[] Do not allow children to play on or in the washer/dryer.

Close supervision of children is necessary when the washer/dryer is used near children.

[] Before the washer/dryer is removed from service or

discarded, remove the doors to the washer/dryer compartments.

[] Do not reach into the washer/dryer if the tub, agitator or

drum is moving.

[] Do not install or store the washer/dryer where it wilt be

exposed to the weather. [] Do not tamper with controls. [] Clean dryer lint screen before or after each load.

[] Under certain conditions, hydrogen gas may be produced in

a hot water system that has not been used for 2 weeks or more. HYDROGEN GAS IS EXPLOSIVE. If the hot water

system has not been used for such a period, before using the washing machine, turn on all hot water faucets and let the water flow from each for several minutes. This will

release any accumulated hydrogen gas. As the gas is

flammable, do not smoke or use an open flame during this time.

[] Do not repair or replace any part of the washer/dryer or

attempt any servicing unless specifically recommended in

this Use and Care Guide or in published user-repair

instructions that you understand and have the skills to carry

out.

[] Do not use fabric softeners or products to eliminate static

unless recommended by the manufacturer of the fabric

softener or product.

[] Do not use heat to dry articles containing foam rubber or

similarly textured rubber-like materials.

[] Keep area around the exhaust opening and adjacent

surrounding areas free from the accumulation of lint, dust,

and dirt.

[] The interior of the machine and dryer exhaust vent should

be cleaned periodically by qualified service personnel.

[] See "Electrical Requirements" section for grounding

instructions.

SAVE THESE INSTRUCTIONS

State of California Proposition 65 Warnings: WARNING: This product contains one or more chemicals known to the State of California to cause cancer.

WARNING: This product contains one or more chemicals known to the State of California to cause birth defects or other reproductive harm.

I IMPORTANT: When discarding or storing your old clothes dryer_ remove the door.

iNSTALLATiON iNSTRUCTiONS

TOOLS AND PARTS

Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here.

Tools needed:

#2 Phillips and fiat- blade screwdriver

Tin snips (for new vent Caulking gun and Level Knife installations) compound (for instaliing

Vent clamps

Adjustable wrench that opens to 1" (25 mm) or 9/16" open-end wrench

(for adjusting dryer feet)

new exhaust vent)

Wire stripper (direct wire

installations)

Pliers Wood block

(for leveling)

Parts supplled:

Remove parts package from the washer basket. Check that all parts were included.

1/4" (6 mm) nut driver or socket wrench

(recommended)

Ruler or measuring tape

Rear leveling legs (2) Front leveling legs (2) Removable tie strap

Silver, double-wire hose clamp

Parts needed: (Not supplied)

Check local codes, electrical supply, and venting, and read "Electrical Requirements" and "Venting Requirements" before purchasing parts.

Mobile home installations require metal exhaust system hardware available for purchase from your local Sears store or Sears Service Center. For further information, please call 1-800-4-MY-HOMi:®

(1-800-469-4663).

Inlet hoses with flat washers

Drain hose

ALTERNATE PARTS

Parts listed are available from your local Sears store or Sears Service Center. For further information, please call

1=800=4=MY-HOME ® (1=800=469=4663).

If you have: Laundry tub or

standpipe taller than 96" (2.4 m)

1" (25 mm) diameter standpipe

Overhead sewer

Floor drain

Drain hose too short

Lint clogged drain Water faucets

beyond reach of fill hoses

You will need to buy: Sump pump system (if not already

available)

2" (51 mm) diameter to 1" (25 mm) diameter standpipe adapter,

Part Number 3363920 Standard 20 gal. (76 L) 34" (864 mm)

tall drain tub or utility sink and sump pump (available from local plumbing

suppliers) Siphon break, Part Number 285320,

additional drain hose, Part Number 285702, and connector kit, Part

Number 285442 Drain hose, Part Number 285664

and connector kit, Part Number 285442 Drain protector, Part Number 367031

2 longer water fill hoses: 6 ft (1.8 m), Part Number 76314,

10 ft (3.0 m), Part Number 350008

Do not operate your washer in temperatures at or below 32°F (0°C). Some water can remain in the washer and can cause

damage in low temperatures. See "Vacation, Storage, and Moving Care" for winterizing information.

Do not operate your dryer at temperatures below 45°F (7°C). At lower temperatures, the dryer might not shut off at the end of an

automatic cycle. This can result in longer drying times. Check code requirements. Some codes limit, or do not permit,

installation of the Laundry Center in garages, closets, mobile homes, or sleeping quarters. Contact your local building inspector.

Installation Clearances

The location must be large enough to allow the dryer door to open fully.

Laundry Center Dimensions

153/o"

(390ram)

71%"

(1.82 m)

LOCATION REQUIREMENTS

Explosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from dryer.

Do not install in a garage. Failure to do so can result in death, explosion, or fire.

You wlll need

[] A location that allows for proper exhaust installation. See

"Venting Requirements".

[] For 240 volt models, a separate 30-amp circuit. For 120 volt

models, a 120 volt, 60 Hz., AC only, 15- or 20-amp circuit.

[] If using a power supply cord on 240 volt models, and for 120

volt models, a grounded electrical outlet located within 2 ft. (610 ram) of either side of the Laundry Center. See "Electrical

Requirements".

[] A sturdy floor to support the Laundry Center weight (Laundry

Center, water, and load) of 500 Ibs (226.8 kg).

[] A level floor with a maximum slope of 1" (25 mm) under

entire Laundry Center. Clothes may not tumble properly and automatic sensor cycles may not operate correctly if Laundry

Center is not level. Installing on carpet is not recommended.

[] A water heater set to deliver 120°F (49°C) water to the washer. [] Hot and cold water faucets located within 4 ft (1.2 m) of the

hot and cold water fill valves, and water pressure of 5-100 psi (34.5-689.6 kPa).

The Laundry Center must not be installed or stored in an area where it will be exposed to water and/or weather.

(816 ram)

*27 ¼" "_

(692ram) *23 z/8"

*Most installations require a minimum 5" (127 ram) clearance behind

the dryer for the exhaust vent with elbow. See "Venting Requirements".

(606 ram)

Minimum spacing far recessed area or closet installation

The following spacing dimensions are recommended for this Laundry Center. This Laundry Center has been tested for spacing

of 0" (0 mm) clearance on the sides, rear, and top. Recommended spacing should be considered for the following reasons:

[] Additional spacing should be considered for ease of installation

and servicing.

[] Additional clearances might be required for wall, door, and

floor moldings.

[] Additional spacing on all sides of the Laundry Center is

recommended to reduce noise transfer.

[]

For closet installation, with a door, minimum ventilation openings in the top and bottom of the door are required. Louvered doors

with equivalent ventilation openings are acceptable.

T (305turn},

(310crn2) I_ t

o oo o o

1"--_1N-26'/_"-_11_-_"

(25mm) (606ram) (25rnm)

*Required spacing

**Rear clearance may be 0" (0 mm) when house exhaust system

is lined up directly with dryer exhaust.

_I"* 1-27'J,"÷I

(25mm)(692mm)

A. Recessed area B. Side view - closet or confined area C. Closet door with vents

(155cm2} I

_.- 6"**

(127mm)

__ 3!'(76mm)

48in,;<.-1

'(76ram)

Moblle Home- Addltlanal Instaffaflon Requirements

This Laundry Center is suitable for mobile home installations. The installation must conform to the Manufactured Home Construction

and Safety Standard, Title 24 CFR, Part 3280 (formerly the Federal Standard for Mobile Home Construction and Safety,

Title 24, HUD Part 280) or the Canadian Manufactured Home Standard, CAN/CSA-Z240 MH.

Mobile home installations require:

[] Metal exhaust system hardware, which is available for

purchase from your local Sears store or Sears Service Center.

[] Special provisions must be made in mobile homes to introduce

outside air into the dryer. The opening (such as a nearby window) should be at least twice as large as the dryer exhaust

opening.

DRAI N SYSTEM

The Laundry Center can be installed using the standpipe drain system (floor or wall), the laundry tub drain system, or the floor

drain system. Select the drain hose installation method you need. See "Alternate Parts".

Standpipe drain system - wall or floor (views A 8, B)

The standpipe drain requires a minimum diameter standpipe of 2" (51 ram). The minimum carry-away capacity can be no less than

17 gal. (64 L) per minute. A 2" (51 mm) diameter to 1" (25 mm) diameter standpipe adapter kit is available. See "Alternate Parts".

The top of the standpipe must be at least 39" (991 ram) high and no higher than 96" (2.4 m) from the bottom of the washer.

39" 1

(991

A B

Laundry tub drain system (view C)

The laundry tub needs a minimum 20 gal. (76 L) capacity. The top of the laundry tub must be at least 34" (864 ram) above the floor

and no higher than 96" (2.4 m) from the bottom of the washer.

Floor drain system (view D)

The floor drain system requires a siphon break that may be purchased separately. See "Alternate Parts".

The siphon break must be a minimum of 28" (710 mm) from the bottom of the washer. Additional hoses might be needed.

ELECTRICAL REQUIREMENTS - 240 VOLT MODELS (U.S.A.) Jt is your responslbility

[] To contact a qualified electrical installer. [] To be sure that the electrical connection is adequate and in

conformance with the National Electrical Code, ANSI/NFPA 70-latest edition and all local codes and ordinances.

A copy of the above code standards can be obtained from: National Fire Protection Association, One Batterymarch Park,

Quincy, MA 02269.

[] To supply the required 3 or 4 wire, single phase, 240 volt, 60

Hz., AC only electrical supply (or 3 or 4 wire, 208 volt electrical supply, if specified on the serial/rating plate) on a separate 30-

amp circuit, fused on both sides of the line. A time-delay fuse or circuit breaker is recommended. Connect to an individual

branch circuit. Do not have a fuse in the neutral or grounding circuit.

[] Do not use an extension cord. [] If codes permit and a separate ground wire is used, it is

recommended that a qualified electrician determine that the ground path is adequate.

ElecfricaJ Connection

To properly install your Laundry Center, you must determine the type of electrical connection you will be using and follow the

instructions provided for it here. [] This dryer is manufactured ready to install with a 3-wire

electrical supply connection. The neutral ground wire is permanently connected to the neutral conductor (white wire)

within the dryer. If the dryer is installed with a 4-wire electrical supply connection, the neutral ground wire must be removed

from the internal ground connector (green screw), and secured under the neutral terminal (center or white wire) of the terminal

block. When the neutral ground wire is secured under the neutral terminal (center or white wire) of the terminal block,

the dryer cabinet is isolated from the neutral conductor,

[] If local codes do not permit the connection of a neutral ground

wire to the neutral wire, see "Optional 3-wire connection" in "Electrical Connection" section.

[] Use a A-wire conductor cord when the dryer is installed in

a mobile home or an area where local codes do not permit grounding through the neutral.

if using a power supply cord:

[] Use a UL listed power supply cord kit marked for use with

clothes dryers. The kit should contain:

[] A UL listed 30-amp power supply cord, rated 240 volt

minimum. The cord should be type SRD or SRDT and be at least 4 ft (1.22 m) long. The wires that connect to the dryer must end

in ring terminals or spade terminals with upturned ends.

[] A UL listed strain relief.

if your outlet looks llke this:

Then choose a 4-wire power supply cord with ring or spade terminals and UL listed strain

relief. The 4-wire power supply cord, at least 4 ft (1.22 m) long, must have four 10-gauge

copper wires and match a 4-wire receptacle of NEMA Type 14-30R. The ground wire (ground

4-wire

receptacle

(14-30R)

conductor) may be either green or bare. The neutral conductor must be identified by a white

cover.

C D

If your outlet looks llke this:

ring or spade terminals and UL listed strain relief. The 3-wire power supply cord, at least 4 ft

(_ hen choose a 3-wire power supply cord with

3-wire

receptacle

(10-30R)

(1.22 m) long, must have three lO-gauge copper wires and match a 3-wire receptacle of NEMA

Type 10-30R.

If connecting by direct wire:

Power supply cable must match power supply (4-wire or 3-wire)

and be:

[] Flexible armored cable or nonmetallic sheathed copper cable

(with ground wire), protected with flexible metallic conduit.

All current-carrying wires must be insulated.

[] 10-gauge solid copper wire. (Do not use aluminum.) [] At least 5 ft (1.52 m) long.

GROUNDING iNSTRUCTIONS

[] For a grounded, cord-connected washer/dryer:

This washer/dryer must be grounded. In the event of malfunction or breakdown, grounding will reduce the risk of

electric shock by providing a path of least resistance for electric current. This washer/dryer uses a cord having an

equipment-grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is

properly installed and grounded in accordance with all local codes and ordinances.

[] For a permanently connected washer/dryer:

This washer/dryer must be connected to a grounded metal, permanent wiring system, or an equipment-grounding

conductor must be run with the circuit conductors and connected to the equipment-grounding terminal or lead on

the washer/dryer.

WARNING: Improper connection of the equipment-

grounding conductor can result in a risk of electric shock. Check with a qualified electrician or service representative or personnel if you are in doubt as to whether the washer/dryer is properly grounded. Do not modify the plug on the power supply cord: if it will not fit the outlet, have a proper outlet installed by a qualified electrician.

SAVE THESE INSTRUCTIONS

ELECTRICAL REQUIREMENTS - 240 VOLT MODELS (CANADA)

Electrical Shock Hazard

Plug into a grounded 4 prong outlet.

Failure to do so can result in death or electrical shock.

It is your responsibility

[] To contact a qualified electrical installer.

[] To be sure that the electrical connection is adequate and in

conformance with the Canadian Electrical Code, C22.1 - latest edition and all local codes A copy of above codes standard

may be obtained from: Canadian Standards Association, 178

Rexdale Blvd., Toronto, ON M9W 1R3CANADA.

[] To supply the required 4 wire, single-phase_ 240 volt_ 60 Hz.,

AC-only electrical supply on a separate 30-amp circuit_ fused on both sides of the line. A time-delay fuse or circuit breaker is

recommended, Connect to an individual branch circuit.

[]

This dryer is equipped with a CSA International Certified Power Cord

intended to be plugged into a standard 14-30R wall receptacle.

The cord is 5 ft. (1.52 m) long. Be sure wall receptacle is within

reach of laundry center's location. 4-wire receptacle (14-30R)

[]

If using a replacement power supply cord, it is recommended that you use Power Supply Cord Replacement Part Number

9831317.

[]

For further information, please reference service numbers located on the back cover.

GROUNDING INSTRUCTIONS

[] For a grounded, cord=connected washer/dryer: This washer/dryer must be grounded. In the event of

malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current. This washer/dryer is equipped with a cord having an equipment-grounding conductor and a grounding

plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with

all local codes and ordinances.

WARNING" Improper connection of the equipment-

grounding conductor can result in a risk of electric shock. Check with a qualified electrician or service representative

or personnel if you are in doubt as to whether the washer/dryer is properly grounded. Do not modify the plug provided with the washer/dryer: if it will not fit the outlet,

have a proper outlet installed by a qualified electrician.

SAVE THESE INSTRUCTIONS

ELECTRICALREQUIREMENTS - 120 VOLT MODELS

Electrical Shock Hazard

Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter.

Do not use an extension cord. Failure to follow these instructions can result in death,

fire, or electrical shock.

[] A 120 volt, 60 Hz., AC only, 15- or 20-amp fused electrical

supply is required.

[] This Laundry Center is equipped with a power supply cord

having a 3 prong grounding plug.

[] Be sure that the electrical connection is adequate and in

conformance with the National Electrical Code, ANSI/NFPA 70-latest edition, or Canadian Electrical Code, C22.1 = latest edition and all local codes and ordinances.

A copy of the above code standards can be obtained from: National Fire Protection Association, One Batterymarch

Park, Quincy, MA 02269 (U.S.A.), or Canadian Standards Association, 178 Rexdale Blvd., Toronto, ON M9W 1R3

CANADA.

[] A time-delay fuse or circuit breaker is recommended. Be sure

fuse or circuit breaker matches the rating of your line.

[] Use a separate circuit serving only your dryer. [] To minimize possible shock hazard, the cord must be plugged

into a mating, 3 prong, grounding-type outlet, grounded in accordance with local codes and ordinances. If a mating outlet

is not available, it is the personal responsibility and obligation of the customer to have the properly grounded outlet installed

by a qualified electrician.

[] If codes permit and a separate ground wire is used, it is

recommended that a qualified electrician determine that the ground path is adequate.

[] Do not ground to a gas pipe. [] Do not use an extension cord.

[] Do not have a fuse in the neutral or ground circuit. [] Check with a qualified electrician if you are not sure the

Laundry Center is properly grounded.

GROUNDING iNSTRUCTiONS

[] For a grounded, cord-connected washer/dryer:

This washer/dryer must be grounded. In the event of

malfunction or breakdown, grounding wilt reduce the risk of electric shock by providing a path of least resistance for electric current. This washer/dryer uses a cord having an equipment-grounding conductor and a grounding plug. The

plug must be plugged into an appropriate outlet that is

properly installed and grounded in accordance with all local codes and ordinances.

WARNING" Improper connection of the equipment-

grounding conductor can result in a risk of electric shock.

Check with a qualified electrician or service representative or

personnel if you are in doubt as to whether the washer/dryer

is properly grounded. Do not modify the plug on the power cord: if it will not fit the outlet, have a proper outlet installed

by a qualified electrician.

SAVE THESE iNSTRUCTiONS

ELECTRICAL CONNECTION - 240 VOLT MODELS (U.S.A ONLY)

Electrlcal Options

1. Choose electrical connection type

Power supply cord 4-wire receptacle (NEMA Type 14-30R): Go to Power Supply Cord Connection,

Power supply cord 3-wire receptacle (NEMA Type 10-30R): Go to Power Supply Cord Connection,

4-wire direct connection: Go to Direct Wire Connection.

__: 3-wire direct connection:

NOTE: If local codes do not permit connection of a cabinet-ground conductor to the neutral wire_ go to

"Optional 3-wire connection" section.

Go to Direct Wire Connection.

2. Remove terminal block cover

n n c

Before you start, disconnect power. Remove hold-down screw (B) and terminal block cover (C).

A. Center terminal block screw B. Hold-down screw

C. Terminal block cover D. External ground conductor screw

Power Supply Cord Connection

Fire Hazard

Use a new UL listed 30 amp power supply cord. Use a UL Jisted strain relief.

Disconnect power before making electrical connections.

Connect neutral wire (white or center wire) to center

terminal

Ground wire (green or bare wire) must be connected to green ground connector.

Connect remaining 2 supply wires to remaining 2 terminals (gold).

Securely tighten all electrical connections.

Failure to do so can result in death, fire, or

electrical shock.

2. Attach power supply cord

to strain relief

-- ,m

Put power supply cord through the strain relief. Be sure that the wire insulation on the power supply cord is inside the strain

relief. The strain relief should have a tight fit with the dryer cabinet and be in a horizontal position. Do not further tighten

strain relief screws at this point.

4=wire Power Supply Cord Connection

iMPORTANT: A 4-wire connection is required for mobile homes and where local codes do not permit the use of

3-wire connections.

1, Attach power supply cord

strain relief

-=-=----==='- A

Remove the screws from a 3/4" (19 mm) UL listed strain relief (UL marking on strain relief). Put the tabs of the two clamp sections (C) into the hole below the terminal block opening

(B) so that one tab is pointing up (A) and the other is pointing down (D), and hold in place. Tighten strain relief screws just

enough to hold the two clamp sections (C) together.

A. Strain relief tab pointing up B. Hole below terminal block opening

C. Clamp section D. Strain relief tab pointing down

4-wire receptacle (NEMA type 14-30R)

Spade terminals with upturned ends

4=prong plug

Ring terminals

1. Connect neutral ground wire and neutral wire

E D _C

3-wire Power Supply Cord Connection

Use where local codes permit connecting cabinet-ground conductor to neutral wire.

3-wire receptacle (NEMA type 10-30R)

3-prong plug

Remove center terminal block screw. Remove neutral ground wire from external ground conductor screw. Connect neutral

ground wire and the neutral wire (white or center wire) of power supply cord under center terminal block screw.

Tighten screw.

A. Center terminal block screw B. Neutral ground wire

C. External ground conductor screw - Dotted

line shows position of NEUTRAL ground wire before being moved to center terminal

block screw.

D. Neutral wire (white or center wire) E. 3/4" (19 mm) UL listed strain relief

"2. Connect ground wire

-o

A C

Connect ground wire (green or bare) of power supply cord to external ground conductor screw. Tighten screw.

A. Neutral wire (white or center wire) B. Center terminal block screw

C. Neutral ground wire D. External ground conductor screw

E. Ground wire (green or bare) of power

supply cord

F. 3/4" (19 mm) UL listed strain relief

Connect the other wires to outer terminal block screws, Tighten screws. Tighten strain relief screws, Insert tab of terminal block

cover into slot of dryer rear panel. Secure cover with hold down screw. Now go to "Venting Requirements'.

Spade terminals with upturned ends

Ring terminals

1. Connect neutral wire

m __ m

Loosen or remove center terminal block screw. Connect neutral wire (white or center wire) of power supply cord to the center terminal screw of the terminal block. Tighten screw.

A. Neutral wire (white or center wire) B. Center terminal block screw

C. Neutral ground wire D. External ground conductor screw E. 3/4" (19 mm) UL listed strain relief

Connect the other wires to outer terminal block screws. Tighten screws. Tighten strain relief screws. Insert tab of terminal block

cover into slot of dryer rear panel. Secure cover with hold-down screw. Now go to "Venting Requirements'.

Direct Wire Connection

Fire Hazard

Use 10 gauge copper wire. Use a UL listed strain relief.

Disconnect power before making electrical connections.

Connect neutral wire (white or center wire) to center

terminal.

Ground wire (green or bare wire) must be connected to green ground connector.

Connect remaining 2 supply wires to remaining 2 terminals (gold).

Securely tighten all electrical connections.

Failure to do so can resuff in death, fire, or

electrical shock.

2. Attach direct wire cable to strain relief

Put direct wire cable through the strain relief. The strain relief

should have a tight fit with the dryer cabinet and be in a horizontal position. Tighten strain relief screw against the

direct wire cable.

if your wiring looks like |his:

4-wire direct connection: Go to "4=wire Direct Wire Connection"

on this page.

3=wire direct connection: Go to "3=wire Direct Wire Connection".

1. Attach direct wire strain relief

Unscrew the removable conduit connector and any screws from a 3/4" (19 mm) UL listed strain relief (UL marking on strain relief). Put the threaded section of the strain relief

through the hole below the terminal block opening. Reaching inside the terminal block opening, screw the removable conduit

connector onto the strain relief threads.

A. Removable conduit connector B. Hole below terminal block opening

C. Strain relief threads

4=wire Direct Wire Connection

IMPORTANT: A 4-wire connection is required for mobile

homes and where local codes do not permit the use of 3-wire connections.

fl. Prepare your 4-wire cable

for direct connection

(127

Direct wire cable must have 5 ft. (1.52 m) of extra length so Laundry Center can

be moved if needed. Strip 5" (127 mm) of outer covering

from end of cable, leaving bare ground wire at 5" (127 ram). Cut 1-1/2" (38 mm)

from remaining 3 wires. Strip insulation back 1" (25 mm). Shape ends of wires into a hook shape.

When connecting to the terminal block, place the hooked end of the wire under the screw of the terminal block (hook facing

right), squeeze hooked end together, and tighten screw. See example above.

2. Connect neutral ground wire

and neutral wire

f4." Connect remaining wires

Place the hooked ends of the other direct wire cable wires under the outer terminal block screws (hooks facing right).

Squeeze hooked ends together. Tighten screws. Tighten strain relief screw. Insert tab of terminal block cover into slot of dryer

rear panel. Secure cover with hold-down screw. Now go to "Venting Requirements".

Remove center terminal block screw. Remove neutral ground wire from external ground conductor screw. Connect neutral

ground wire and place the hooked end (hook facing right) of the neutral wire (white or center wire) of direct wire cable

under the center screw of the terminal block. Squeeze hooked ends together. Tighten screw.

A. Center terminal block screw B. Neutral ground wire

C. External ground conductor screw - Dotted

line shows position of NEUTRAL ground wire before being moved to center terminal

block screw.

D. Neutral wire (white or center wire) E. 3/4" (19 mm) UL listed strain relief

3. Connect ground wire

3-wlre Direct Wire Connection

Use where local codes permit connecting cabinet-ground conductor to neutral wire.

1. Prepare your 3-wire cable

for direct connection

Direct wire cable must have 5 ft. (1.52 m) of extra length so Laundry Center can

be moved if needed. Strip 3-1/2" (89 mm) of outer covering

from end of cable. Strip insulation back 1" (25 mm). if using 3-wire cable with

ground wire, cut bare wire even with outer covering. Shape ends of wires into a hook shape.

When connecting to the terminal block, place the hooked end of the wire under the screw of the terminal block (hook facing

right), squeeze hooked end together, and tighten screw. See example above.

Connect ground wire (green or bare) of direct wire cable to external ground conductor screw. Tighten screw.

A. Neutral wire (white or center wire) B. Center terminal block screw

C. Neutral ground wire D. External ground conductor screw

E. Ground wire (green or bare) of direct

wire cable

F. 3/4" (19 mm) UL listed strain relief

2. Connect neutral wire

Loosen or remove center terminal block screw. Place the hooked end of the neutral wire (white or center wire) of direct

wire cable under the center screw of terminal block (hook facing right). Squeeze hooked end together. Tighten screw.

A. Neutral wire (white or center wire) B. Center terminal block screw

C. Neutral ground wire D. External ground conductor screw

E. 3/4" (19 mm) UL listed strain relief

3. Connect remaining wires

. Connect neutral ground wire

and neutral wire

A "o o 1 'B

Remove center terminal block screw. Remove neutral ground wire from external ground conductor screw. Connect neutral

ground wire and the neutral wire (white or center wire) of power supply cord/cable under center terminal block screw.

Tighten screw.

A. Neutral wire (white or center wire) B. Neutral ground wire

C. External ground conductor screw - Dotted

line shows position of NEUTRAL ground wire before being moved to center terminal

block screw.

D. Grounding path determined by a qualified

electrician

Place the hooked ends of the other direct wire cable wires under the outer terminal block screws (hooks facing right).

Squeeze hooked ends together. Tighten screws. Tighten strain relief screw. Insert tab of terminal block cover into slot of dryer

rear panel. Secure cover with hold-down screw. Now go to "Venting Requirements".

Optional 3-wire Connection

Use for direct wire or power supply cord where local codes do not permit connecting cabinet-ground conductor to neutral

wire.

f2. Connect remaining wires and

connect separate ground wire

Connect the other wires to outer terminal block screws. Tighten screws. Tighten strain relief screws. Connect a separate copper

ground wire from the external ground conductor screw to an adequate ground. Insert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold-down screw. Now

go to "Venting Requirements".

VENTING REQUIREMENTS

Fire Hazard

Use a heavy metal vent, Do not use a plastic vent.

Do not use a metal foil vent. Failure to follow these instructions can result in death

or fire.

WARNING: To reduce the risk of fire, this Laundry Center

MUST BE EXHAUSTED OUTDOORS.

iMPORTANT: Observe all governing codes and ordinances. Dryer exhaust must not be connected into any gas vent, chimney, wall, ceiling, attic, crawlspace, or a concealed space of a

building. Only rigid or flexible metal vent shall be used for exhausting.

Exhaust hoods:

[] Must be at least 12" (305 ram) from ground or any object

that may obstruct exhaust (such as flowers, rocks, bushes, or snow).

[] Do not use an exhaust hood with a magnetic latch.

Recommended Styles:

Louvered Hood Box Hood

Acceptable Style:

Angled Hood

Elbows:

[] 45 ° elbows provide better airflow than 90 ° elbows.

(102 mm)

0 4"

4" (102 mm) heavy metal exhaust vent

[] Only a 4" (102 ram) heavy metal exhaust vent and clamps

may be used. DURASAFE TM venting products are recommended.

[] Do not use plastic or metal foil vent.

Rigid metal vent:

[] Recommended for best drying performance and to avoid

crushing and kinking.

Fle×ible metal vent: (Acceptable only if accessible to clean)

[] Must be fully extended and supported in final Laundry

Center location.

[] Remove excess to avoid sagging and kinking that may

result in reduced airflow and poor performance.

[] Do not install in enclosed walls, ceilings, or floors. [] The total length should not exceed 7=3/4 ft. (2.4 m).

[] The length of flexible metal vent used must be included in the

overall vent system design as shown in the "Vent System Chart".

NOTE: If using an existing vent system, clean lint from entire length of the system and make sure exhaust hood is not plugged with

lint. Replace plastic or metal foil vents with rigid metal or flexible metal vents. Review Vent System Chart and if necessary, modify

existing vent system to achieve best drying performance.

Recommended Styles:

Bet

Clamps:

[] Use clamps to seal all joints. [] Exhaust vent must not be connected or secured with screws

or other fastening devices that extend into interior of duct and catch lint. Do not use duct tape.

improper venting can cause moisture and lint to collect indoors, which may result in:

[] Moisture damage to woodwork, furniture, paint, wallpaper,

carpets, etc.

[] Housecleaning problems and health problems.

Vent products can be purchased from your dealer. For further information, please call I=800=4-MY=HOME ® (1=800=469=4663) or visit our website at wv_w.sears.corn or v_ww.sears.ca.

iNSTALL LEVELING LEGS

Excessive Weight Hazard

Use two or more people to move and install washer/dryer. Failure to do so can result in back or other injury,

To avoid damaging floor, use a large flat piece of cardboard from shipping carton. Gently place Laundry Center on its side, on the

cardboard.

1. install rear leveling legs

CONNECT DRAIN HOSE

Proper connection of the drain hose avoids damage to your floors

due to water leakage. To keep the drain hose from coming off or leaking, it must be installed according to the following instructions:

iMPORTANT: To ensure proper installation, this procedure must be followed exactly.

. Attach clamp to drain hose

Push legs into holes in rear corners until they snap into place.

Check adjustability of rear legs by pushing in one leg. The other leg should come out. Check both legs. If they do not

move freely, repeat procedure.

Examine front leveling legs; find diamond marking. Screw front legs by hand into holes in triangular braces in front corners. Use wrench to finish turning the legs until diamond marking is

no longer visible. Gently stand Laundry Center upright.

REMOVE FOAM PACKING

1. Pull foam packing ring out of washer

Check the drain hose to see whether it is the proper length. Wet the inside of the straight end of the drain hose with

tap water. iMPORTANT: Do not use any lubricant other than water.

Squeeze the ears of the silver, double=wire clamp with pliers to open. Place clamp over the straight end of the drain hose 1/4" (6.4 mm) from the end.

F2. Attach drain hose to drain connector

- m

Open clamp. Twist hose back and forth while pushing onto drain connector on the side of the Laundry Center. Continue

until hose contacts the ribbed stops on the cabinet. Place clamp over the area marked "CLAMP." Release clamp.

-- w __

Open the washer lid. The latch under the dryer will keep the lid open. PuJJthe foam packing ring out of the washer.

NOTE: Keep the foam ring and use it when transporting your Laundry Center. This packing material is used to keep

the washer tub stable during transport.

Place drain hose in standpipe or laundry tub

Drain

2. Connect inlet hoses to water faucets

Make sure drain hose form is in correct position. Place hose into standpipe (shown) or over side of laundry tub.

IMPORTANT: 4.5" (114 mm) of drain hose should be inside standpipe; do not force excess hose into standpipe or lay

on bottom of laundry tub. Drain hose form must be used.

For use with floor drain: Do not install the drain hose form onto the corrugated drain hose. You may need additional

parts. See Floor drain under "Alternate Parts".

CONNECT iNLET HOSES

Laundry Center must be connected to water faucets with new inlet hoses with flat washers (not provided). Do not use old hoses.

NOTE: Both hoses must be attached and have water flowing to inlet valves.

"1. insert washer into each hose _

% ........... _,

Insert a new fiat washer into each end of the inlet hoses (not provided). Firmly seat the washers in the couplings.

Make sure the washer basket is empty. Attach hose to the hot water faucet. Screw on coupling by hand until it is seated on

the washer. Attach hose to the cold water faucet. Screw on coupling by hand until it is seated on the washer. Using pliers0

tighten the couplings with an additional two-thirds turn. iMPORTANT: Do not overtighten or use tape or sealants

when attaching inlet hoses to faucets or to the Laundry Center. Damage can result.

3. Clear water lines

Run water through both faucets and inlet hosessinto a laundry tub, drainpipe, or bucket to get rid of particles in the

water lines that might clog the inlet valve screens. Check the temperature of the water to make sure that the hot water hose is connected to the hot water faucet and that the cold water hose is connected to the cold water faucet.

4. Connect inlet hoses to washer

f6. Check for leaks

Attach the hot water hose to the bottom inlet valve. Attaching the hot water hose first makes it easier to tighten connection

with pliers. Screw on coupling by hand until it is seated on the washer. Using pliers, tighten the coupling with an additional two-thirds turn.

Attach the cold water hose to the top inlet valve. Screw on coupling by hand until it is seated on the washer. Using pliers, tighten the coupling with an additional two-thirds turn.

iMPORTANT: Do not overfighten or use tape or sealants when attaching inlet hoses to faucets or to the Laundry Center.

Damage can result.

A. Cold water inlet valve (top) B. Hot water inlet valve (bottom)

5. Move laundry center to final location

66 66

Turn on the water faucets and check for leaks. A small amount of water might enter the washer. You wHJ drain this later.

NOTE: Replace inlet hoses after 5 years of use to reduce the risk of hose failure. Record hose installation or replacement dates for future reference.

If you connect only one water hose, you must cap off the remaining water inlet port.

Periodically inspect and replace hoses if bulges, kinks, cuts, wear, or leaks are found.

The Laundry Center must be connected to the water faucets using the new hoses. Do not use old hoses.

SECURE DRAIN HOSE

Move Laundry Center to its flnaJ location and remove any cardboard used to move Laundry Center.

Wrap the drain hose to laundry tub leg or standpipe

If you are working in a closet or recessed area_ move the Laundry Center into its final location and remove cardboard

from under the Laundry Center. Remove the access panel by removing 2 Phillips-head screws located at the top of the

access panel. Set panel and screws aside. Complete hookup of water hoses through the access area. Replace access panel

upon completion of Laundry Center installation.

B C D

Locate removable tie strap (A) included in parts package. Wrap the drain hose to the laundry tub leg (B) or standpipe (C)

with the removable tie strap and secure. If the water faucets and the drain standpipe are recessed, put the hooked end of

the drain hose in the standpipe. Tightly wrap the removable tie strap around the water inlet hoses and the drain hose (D).

PLAN VENT SYSTEM

Recommended exhaust installations

Typical installations vent the dryer from the rear of the Laundry Center. Other installations are possible.

--D

Alternate installations for close clearances

Venting systems come in many varieties. Select the type best for your installation. Three close-clearance installations are shown.

Refer to the manufacturer's instructions provided with the vent system.

! i

A. Dryer E. Elbow B. Rigid metal or flexible metal vent F. Clamps

C. Clamps G. Elbow D. Wall H. Exhaust hood

Optional exhaust installations

This Laundry Center can be converted to exhaust out the right or left side. To convert the Laundry Center, use Side Exhaust Kit Part Number 279823. If your Laundry Center was previously exhausted

from the right or left side, it can be converted to rear exhaust by using standard offset connections. To cover the hole in the side,

one of the following plugs can be added: 692790 (white)

3979370 (graphite) 3977784 (biscuit)

Follow the instructions in the kit to install. Kits are available from your local Sears store or Sears Service Center.

S ........

ii ! i!

,,,! i

A B C

A. Loop system with standard elbows B. Loop system with one offset and one standard elbow C. Vent system with one periscope (2" [51 mm] clearance)

NOTE: The following kits for close clearance alternate installations are available for purchase. To order, please call

1-800-4-MY-HOME ® (1-800-469-4663).

Over-the-Top Installation: Periscope Installation

(For use with dryer vent to wall vent mismatch):

Part Number 26-49900 Part Number 26-49901 -

Less than 5" (127 mm) mismatch

Part Number 26-49908 - 5" (127 mm) to 18" (457 mm)

mismatch Part Number 26-49904 -

18" (457 mm) to 29" (737 mm) mismatch

Part Number 26-49905 - 29" (737 mm) to 50" (1.27 m)

mismatch

Speclal provisions for mobile home installations

The exhaust vent must be securely fastened to a noncombustible portion of the mobile home structure and must not terminate

beneath the mobile home. Terminate the exhaust vent outside.

A. Standard rear offset exhaust installation B. Rear exhaust for offset close clearance connection

C. Left or right side exhaust installation

Determine vent path [] Select the route that will provide the straightest and most

direct path outdoors.

[] Plan the installation to use the fewest number of elbows

and turns.

[] When using elbows or making turns, allow as much room

as possible.

[] Bend vent gradually to avoid kinking. [] Use the fewest 90 ° turns possible.

Determine vent length and elbows needed for best drying performance

[] Use the Vent system chart below to determine the type of vent

material and hood combinations acceptable to use. NOTE= Do not use vent runs longer than those specified in the

Vent system chart. Exhaust systems longer than those specified wilh

[] Shorten the life of the dryer. [] Reduce performance, resulting in longer drying times and

increased energy usage.

The Vent system chart provides venting requirements that wJJJ help to achieve the best drying performance.

Vent System Chart

Side exhaust installations add a 90 ° turn inside the

Laundry Center. To determine maximum exhaust length, add one 90 ° turn to the chart.

2. Connect vent to exhaust hood

Vent must fit inside the exhaust hood. Secure vent to exhaust hood with 4" (102 mm) clamp. Run vent to dryer location using straightest path possible. See "Determine vent path" Jn "Plan

Vent System". Avoid 90 ° turns. Use clamps to seal all joints. Do not use duct tape, screws, or other fastening devices that

extend into interior of vent to secure vent, because they can catch lint.

CONNECT VENT

Number Box or

of 90 ° turns Type iouvered Angled

or elbows of vent hoods hoods

0 Rigid metal 43 ft. (13.1 m) 36 ft. (11.0 m)

1 Rigid metaJ 33 ft. (10.1 m) 26 ft. (7.9 m)

2 Rigid metaJ 23 ft. (7.0 m) 16 ft. (4.9 m)

INSTALL VENT SYSTEM

]. install exhaust hood

. Connect vent to exhaust outlet

Connecting from front

(for closet or recessed area)

Using a 4" (102 mm) clamp, connect vent to exhaust outlet in Laundry Center. if connecting to existing vent, make sure the

vent is clean. Dryer vent must fit over dryer exhaust outlet and inside exhaust hood. Check that vent is secured to exhaust

hood with a 4" (102 mm) clamp.

Connecting

from rear

2. Move Laundry Center to final location

_11|ii ,,_.......... }:/

Install exhaust hood and use caulking compound to seal exterior wall opening around exhaust hood.

Move Laundry Center to its final location. Avoid crushing or kinking vent.

LEVELLAUNDRY CENTER

Properly (evelJng your Laundry Center avoids excessive noise and vibration.

1. Check levelness of laundry center

Check levelness of Laundry Center by placing a level on the top edge of washer, first side to side, then front to back. if

Laundry Center is not level, prop up front with a wood block and adjust feet up or down as necessary. Remove wood block

and lower Laundry Center. Repeat this step until Laundry Center is level.

COMPLETE iNSTALLATiON

[] Check that all parts are now Jnsta(Ned. if there isan extra

part, go back through the steps to see what was skipped. [] Check that you have all of your tools. [] Dispose of/recycle all packaging materials. Keep the plastic

foam for use if Laundry Center should be transported. [] Check Laundry Center's final location. Be sure vent is not

crushed or kinked. [] Check that Laundry Center is level and front leveling feet

are tight. See "Level Laundry Center." [] On 240 volt models, for power supply cord installation,

plug into an outlet. For direct wire installation (U.S. only),

turn on power. On 120 volt models, plug into a grounded

3 prong outlet. [] Check that the water faucets are on.

[] Check for leaks around faucets and inlet hoses. [] Remove film on the console and any tape remaining

on Laundry Center. [] Read "Washer Use" and "Dryer Use."

[] Wipe dryer drum interior thoroughly with a damp cloth

to remove any dust. [] To test the washer, measure 1/2 the normal recommended

amount of detergent and pour it into the washer. C(ose the lid.

Select HEAVY DUTY and pull out the CYCLE CONTROL knob.

Allow the washer to complete one whole cycle. [] To test the dryer, set the dryer on a full heat cycle

(not an air cycle) for 20 minutes and start the dryer.

if the dryer wff[ not start, check the follow(rig:

* Controls are set in a running or "On" position.

* PUSH TO START DRYER button has been firmly pushed.

* On 240 volt models, Laundry Center is plugged into an

outlet and/or electrical supply is on. On 120 volt models_ Laundry Center is plugged into a grounded 3 prong outlet

and/or electrical supply is on.

* Household fuse is intact and tight, or circuit breaker

has not tripped.

* Dryer door is closed.

[] When the dryer has been running for 5 minutes, open the dryer

door and feel for heat. if you feel heat, cancel cycle and close the door.

if you do not feel heat, turn the dryer off and check the follow(rig:

* Controls are set on a heated cycle, not an air cycle. * On 240 volt models, there may be 2 household fuses or

circuit breakers for the dryer. Check that both fuses are intact and tight, or that both circuit breakers have not

tripped. If there is still no heat, contact a qualified technician.

NOTE: You may notice an odor when dryer is first heated. This odor is common when the heating element is first used. The odor

wJH go away.

CONTROL PANEL AND FEATURES

240 Volt Models

Spi_

Heavy

Duty

120 Volt Models

Heavy

Duty

=_elicates

Spin

PUSH TO STOP

Not all features and options are available on all models.

Rinse

Spin

WASHER USE

Delicates

Rinse

Wash Temp Soil Level

Rinse

Spin

68FP

Cool _ Light e Heavy

Cold e ff_ "_ I1e Hot

Darks(L_" _\'x_War m ___

Appearance may vary.

Wash Temp Soil Level

Cool Lights Medium

Cool __oe Light • Heavy

Cold • H _. _. _I• Hot

oo. \ wo.m zj

Cool Lights Medium

WASH = SELECT = DRY

STARTING YOUR WASHER

Fire Hazard

Never place items in the washer that are dampened with gasoline or other flammable fluids.

No washer can completely remove off. Do not dry anything that has ever had any type of oil on

it (including cooking oils). Doing so can result in death, explosion, or fire.

WARNING: To reduce the risk of fire, electric shock, or injury to

persons, read the IMPORTANT SAFETY INSTRUCTIONS before operating this washer.

The following is a guide to starting your washer. Periodic references to other sections of this manual provide more detailed

information.

[] Add a measured amount of detergent or single-dose laundry

packet into the basket before adding clothes. If using OxJ-type boosters, color=safe bleach, or fabric softener crystals, add to the bottom of the washer basket as well.

[] Place a load of sorted clothes in the washer.

• Load evenly to maintain washer balance. Mix large and small items. See "Loading".

Tightly packed loads may cause poor cleaning.

[][]Close the washer lid.

Turn the SOIL LEVEL selector knob to the correct setting for your wash load and the type of fabric

being washed.

Soil Level

Medium

Light _ee Heavy

[][]Set the WASH TEMP selector

to the correct setting for the type of fabric and soils being washed.

Use the warmest water safe for the fabric. Follow garment label

instructions. All rinses are cold rinses.

Wash Ternp Hot

Warm Cool

Cold Push in the CYCLE CONTROL knob and turn it clockwise

to the wash cycle you want. Pull out the CYCLE CONTROL knob to start the washer.

To stop or restart your washer: [] To stop the washer at any time, push in the CYCLE CONTROL

knob.

[] To restart the washer, close the lid (if open) and pull out the

CYCLE CONTROL knob.

Use For Whites and pastels; Heavy soils

Bright colors; Moderate to light soils Colors that bleed or fade; Light soils

Colors that bleed or fade; Light soils

WashTamp

Cool Lights

Cool

Colde_ _J;oHot

CYCLES

This section describes the available wash cycles and will help you make the best cycle

selections for your Heavy wash loads. Each Duty

cycle is designed for different types 18 of fabric and soil levels. 12

[] The washer pauses

briefly throughout each cycle. These

pauses are normal. Refer to "Normal Sounds"

for sounds you may hear during a wash cycle.

[]

Refer to "Understanding Washer Cycles" to learn what happens during a wash cycle.

Spln

Rinse

Spin

Delicates

Rinse

Soak The Soak cycle features 4 minutes of agitation followed by an

unlimited soak time to help remove heavy soils and stains that need pretreatment. You will need to reset the washer to a Spin

setting to remove water. [] The Soak cycle should be followed by the Heavy Duty,

Casual, or Prewash cycle with additional detergent.

NOTE: Hot water is not recommended for soaking. It may set some stains.

Prewash

Use this cycle to get up to 4 minutes of agitation to help remove heavy soils and stains that need pretreatment.

[] The Prewash cycle should be followed by the Heavy Duty or

Casual cycle with additional detergent.

RINSE AND SPIN

When using extra detergent for heavily soiled clothes, or when washing special-care items, you may find an extra rinse and spin

is needed. [] Push in the CYCLE CONTROL knob and turn it clockwise to any

of the Rinse settings.

* For fast agitation and spin, use the Heavy Duty cycle. * For slow agitation and spin, use the Casual cycle.

[] Set SOIL LEVEL and WASH TEMP controls to the desired

setting.

[] Pull out the CYCLE CONTROL knob. The washer automatically

fills to the correct load size, agitates, drains, and spins.

DRAIN AND SPIN

A drain and spin may help shorten drying times for some heavy fabrics or special-care items by removing excess water.

[] Push in the CYCLE CONTROL knob and turn it clockwise

to any of the Spin settings.

* For a fast spin, use the Heavy Duty cycle. * For a slow spin, use the Casual cycle.

[] Pull out the CYCLE CONTROL knob. The washer drains,

then spins.

Heavy Duty

Use this cycle for sturdy or heavily soiled loads. The wash combines fast-speed agitation and fast spin speed.

[] Select cycle agitation time (8, 10, or 12 minutes); choose more

time for heavily soiled, sturdy fabrics and less time for lightly soiled, sturdy fabrics.

Casua_

The Casual cycle includes a load-cooling process that reduces wrinkling. The wash combines fast- and slow-speed agitation and

slow spin speed. Part way through the cycle, the washer will pause for

approximately 2 minutes while some of the wash water is drained and replaced with rinse water.

Delicates

Use this cycle for lingerie and loosely knit items. Part way through the cycle, the washer pauses and soaks the load for gentler care

of lightly soiled delicate items. The wash combines slow speed agitation for gentle soil removal and slow spin speed to reduce

wrinkling.

UNDERSTANDING WASHER CYCLES

When the Cycle Control knob is set to a cycle and pulled out, the washer fills before agitation and timing start. The washer

begins agitating immediately after filling; agitation occurs with the washer lid down.

During agitation, the agitator creates a continuous roJlover action that provides

a thorough cleaning of the wash load. After agitation starts, the Cycle Control

knob turns clockwise until it points to an Off: area and the cycle ends.

NOTE: The washer pauses briefly throughout each cycle. These pauses are normal for washer operation.

Wash Rinse

1. Fill _ 1. Fill

2. Rinse

selected

2. Wash

time

No agitation No agitation

3. Drain _" _J 3. Drain

LAUNDRY TiPS

Preparing clothes for washing

Follow these recommendations to help you prolong the life of your garments.

[] Close zippers, snaps, and hooks to avoid snagging other

items. Remove p(ns, buckles, and other hard objects to avoid scratching the washer interior. Remove non-washable trim

and ornaments. [] Empty pockets and turn them inside out. [] Turn down cuffs, brush away lint and dirt.

[] Turn synthetic knits inside out to avoid pilling. [] Tie strings and sashes so they will not tangle.

[] Mend tears, loose hems, and seams. [] Treat spots and stains.

[] Stained or wet garments should be washed promptly

for best results.

Sorflng

[] Separate heavily soiled items from lightly soiled ones, even

if they would normally be washed together. Separate lint

givers (towels, cheni((e) from lint takers (corduroy, synthetics,

permanent press). When possible, turn lint givers inside out. []

Separate dark colors from light colors, colorfast items from non

colorfast items. []

Sort by fabric and construction (sturdy cottons, knits, delicate

items).

_J_ 4. Spin _ 4. Spin-Spray

_The Casual cycle partially _ J I I 6. Off

drains, fills, agitates briefly, and drains

Rinse

5. Spin

NORMAL SOUNDS

As with any new product, you will hear sounds that you are not accustomed to. You may hear various sounds occurring during

the washing, rinsing, and spinning process. Between changes in wash actions, there will be momentary pauses. You will hear water

spraying and splashing during the wash and rinse cycles. You may hear air being pulled through the pump during the end of draining

or gears changing when the cycle changes. These sounds are part of normal washer operation.

LOADING Loading suggestions (maximum size loads)

Laundry Center

Heavy Work Clothes

2 pair pants 3 work shirts

Casual

6 shirts or 2 double sheets & 2 pillowcases or 2 single sheets &

2 pillowcases Knits

2 pair pants & 2 shirts or 3 dresses

Towels

9 bath towels or 6 bath towels,

3 hand towels & 6 washcloths

Mixed Load

1 pair pants 2 pillowcases

2 shirts 1 T-shirt

Delicates

1 camisole 2 slips

4 undergarments 1 set of sleepwear

1 half slip

CONTROL PANEL AND FEATURES

240 Voff Models

DRYER USE

120 Voff Models

Push to Start

Dryer

WASH - SELECT - DRY

Auto Dry Less_._ OFF=._More Auto Dry

M°re___ ess

AirO.,Y_o___ ..%

20- Touch Up

110

100

Touch

LID LATCH V

Not all features and options are available on all models.

Appearance may vary.

STARTING YOUR DRYER

Explosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from dryer.

Do not dry anything that has ever had anything

flammable on it (even after washing).

Failure to follow these instructions can result in death,

explosion, or fire.

WARNING: To reduce the risk of fire, electric shock, or injury to

persons, read the IMPORTANT SAFETY INSTRUCTIONS before operating this appliance.

Before using your dryer, wipe the dryer drum with a damp cloth to remove dust from storing and shipping.

[] Clean lint screen before each load.

See "Cleaning the Lint Screen".

[] Load clothes loosely into the dryer and

close the door. Do not pack the dryer. Allow space for clothes to tumble freely.

[] Turn the CYCLE CONTROL knob to the

recommended cycle and temperature for the type of load being dried. See

"Drying, Cycle, and Temperature Tips."

[] On 120 volt models, slide WASH/DRY

selector to DRY.

[] Press the PUSH TO START DRYER knob.

Push fo Start

Dryer

STOPPING AND RESTARTING

You can stop your dryer anytime during a cycle. To stop your dryer

Open the dryer door or turn the CYCLE CONTROL knob to Off. NOTE: The Cycle Control knob should point to an Off area when

the dryer is not in use. To restart your dryer

[] Close the door. [] Select a new cycle and temperature (if desired).

[] Press the PUSH TO START DRYER knob.

Fire Hazard

No washer can compJetely remove oil. Do not dry anything that has ever had any type of oil on

it (including cooking oils).

items containing foam, rubber, or plastic must be dried on a clothesline or by using an Air Cycle.

Failure to follow these instructions can result in death

or fire.

DRYING, CYCLE, AND TEMPERATURE TiPS

Select the correct cycle and temperature for your load. Drying flps

[] Follow care label directions when they are available. [] If you use fabric softener sheets, use only those labeled

as dryer safe. Follow package instructions. [] Remove the load from the dryer as soon as tumbiing stops

to reduce wrinkJing. This is especially important for permanent

press, knits, and synthetic fabrics. Cycle and temperature flps

[] Dry most loads using the Auto Dry Normai setting. [] Use the More setting for drying heavyweight items such

as towels and work clothes. [] Use an Auto Dry NormaJ setting for drying medium weight

items such as sheets, underwear, permanent press fabrics,

and some knits. [] Use the Less setting for drying lightweight items such as

lingerie, blouses, dresses, and some knits. [] Use Air Only setting for rubber, plastic, or heat-sensitive

fabrics. [] Line dry bonded or laminated fabrics. If you are unsure of the temperature to select for a load, select a

lower setting rather than a higher setting. NOTE: If you have questions about drying temperatures for various

loads, refer to the care label directions.

Load clothes loosely into the dryer. Do not pack the dryer. Allow space for clothes to tumble freely. The following chart shows

examples of balanced loads that would allow for proper tumbling.

Heavy work

clothes

Delicates I camisole, 2 slips, 4 undergarments,

Towels 9 bath towels or 6 bath towels,

Mixed Load 2 pillowcases, 1 T-shirt, 2 shirts,

Knits 2 pants, 2 shirts; or 3 dresses

Permanent 6 shirts; or 2 double sheets & 2 pillowcases; Press or 2 single sheets & 2 pillowcases

2 pair pants, 3 work shirts

1 set of sleep wear, I half slip

3 hand towels, 6 washcloths

I pair pants

CYCLES

Auto Dr_ AuotODTrY Le_ OFF_Morl[:e_ e Au,toDry

Use this cycle to dry Normal_ _- -_ormaJ most loads. Dryness is , ,if _ "_Less

determinedbythermostats/ \ l

that react to the temperature OFF //'-_ _ \_ or amount of moisture [I "_ _ II OFF in the air exhausted _ \\ "_ "x,,J/ r-_

from the dryer. 10\'\ \\ X / /_50

. . Air OnlY'2o_ _/'/_o

This cycle includes a //_0 5 minute (approximate) OFF _ _j_,-',,_30Timed Dry cool down period at the end "_---_'_20-Touch Up

of the cycle to make clothes ]0 easier to handle and to reduce 240 volt model shown

wrinkling. Use Auto Dry Normal cycle to dry most heavy- to medium-weight

fabrics. When the cycle ends, check the dryness of the load. [] If the load is drier than you like, select a setting closer to LESS

the next time you dry a similar load.

[] If the load is not as dry as you like, complete drying using the

Timed Dry cycle. The next time you dry a similar load, select a setting closer to MORE.

NOTE: Drying time with an automatic cycle varies according to the type of fabric, size of load, and temperature setting.

See "Drying, Cycle, and Temperature Tips".

Timed Dry

Use this cycle to complete drying if items are still damp after the Auto Dry cycle. Timed Dry is also useful for heavyweight

and bulky items, such as bedspreads, work clothes, and large loads that require a long drying time. Use this cycle to get up

to 50 minutes of heated drying time on 240 volt models, or up to 110 minutes of heated drying time on 120 volt models.

The heating cycle is followed by a 5 minute (approximately) cool down period.

Touch Up

Use this cycle to smooth already dry synthetic and permanent press clothes that are clean but wrinkled from being crowded in a

closet or suitcase. This setting provides approximately 20 minutes of heated tumbling followed by a 5 minute (approximately) cool

down period. Remove clothes immediately when tumbling stops.

Air Only

Use the Air Only cycle for items that require drying without heat such as rubber, plastic, and heat-sensitive fabrics. This chart shows

examples of items that can be dried using an air cycle.

Type af Laad Minutes _ Foam rubber - pillows, padded bras, 20-30

stuffed toys Plastic items - shower curtains, tablecloths 20-30

Rubber-backed rugs 40-50 Olefin, polypropylene, sheer nylon 10-20

_Reset time as needed to allow items to completely dry.

When using Air Only

[] Check that coverings are securely stitched. [] Shake and fluff pillows by hand periodically during the cycle.

[] Dry items completely. Foam rubber pillows are slow to dry.

End of Cycle Signal

Your dryer sounds a signal when a drying cycle is finished. This signal is helpful when you are drying items that need to be

removed as soon as the dryer stops in order to help keep wrinkles from forming.

LAUNDRY CENTER CARE

CLEANING THE LAUNDRY CENTER LOCATION

Keep the Laundry Center area clear and free from items that would obstruct the flow of combustion and ventilation air.

Explosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from dryer.

Failure to do so can result in death, explosion, or fire.

CLEANING YOUR WASHER

Cleanlng the exterior

Use a soft, damp cloth or sponge to wipe up any spills such as detergent or bleach. Occasionally wipe the outside of your washer to keep it looking new.

Cleanlncj the interior Keep your washer as clean and fresh as your clothes. To keep

washer interior odor-free, follow this recommended monthly cleaning procedure:

1. Make sure the washer is empty.

2. Using recommended affresh <_>washer cleaner, add one tablet

to washer basket OR

If using liquid chlorine bleach, add 1cup (250 mL) to washer basket.

iMPORTANT: Do not add detergent. Do not use more than recommended amount of bleach to avoid damaging product

over time.

3. Close washer lid.

4. Select Heavy Duty cycle, hot temperature, and

Heavy soil level.

5. Pull out the Cycle knob. Water will pour into washer

for a moment and pause, lid will lock, then cycle

will continue. NOTE: For best results, do not interrupt cycle. If cycle must be

interrupted, push in the Cycle knob.

WATER INLET HOSES

Replace inlet hoses after 5 years of use to reduce the risk of hose failure. Periodically inspect and replace inlet hoses if bulges, kinks,

cuts, wear, or leaks are found. When replacing your inlet hoses, mark the date of replacement

on the label with a permanent marker.

CLEANING THE LINT SCREEN

Every load cleaning The lint screen is located on the back wall of the dryer. Remove

lint before each load. A screen blocked by lint can increase drying time.

To clean

1. Pull out the lint screen and its cover.

2. Separate the cover and the screen by squeezing the screen and pulling on the cover at the same time.

A. Screen B. Cover

3. Roll lint off the screen with your fingers. Do not rinse or wash screen to remove lint. Wet lint is hard to remove.

To wash

1. Roll lint off the screen with your fingers.

2. Wet both sides of lint screen with hot water.

3. Wet a nylon brush with hot water and liquid detergent. Scrub lint screen with the brush to remove residue buildup.

4. Rinse screen with hot water.

5. Thoroughly dry lint screen with a clean towel. Replace screen in dryer.

CLEANING THE DRYER INTERIOR

To dean dryer drum

1. Apply a liquid, nonflammable household cleaner to the stained area and rub with a soft cloth until all excess dye is removed.

2. Wipe drum thoroughly with a damp cloth.

3. Tumble a load of clean cloths or towels to dry drum.

NOTE: Garments that contain unstable dyes, such as denim blue

jeans or brightly colored cotton items, may discolor the dryer

interior. These stains are not harmful to your dryer and will not stain future loads of clothes. Dry unstable dye items inside out

to avoid dye transfer.

REMOVING ACCUMULATED LINT

From Inslde the Dryer Cabinet Lint should be removed every 2 years, or more often, depending

on dryer usage. Cleaning should be done by a qualified person.

From the Exhaust Vent Lint should be removed every 2 years, or more often, depending

on dryer usage.

4. Put the lint screen and cover back together and push firmly back into place.

iMPORTANT: [] Do not run the dryer with the lint screen loose, damaged,

blocked, or missing. Doing so can cause overheating and damage to both the dryer and fabrics.

[] If lint falls off the screen into the dryer during removal, check

the exhaust hood and remove lint. See "Venting Requirements".

As needed cleanlng Laundry detergent and fabric softener residue can build up on

the lint screen. This buildup can cause longer drying times for your clothes, or cause the dryer to stop before your load is completely

dry. The screen is probably clogged if lint falls off the screen. Clean the lint screen (as outlined following) every 6 months, or

more frequently if it becomes clogged due to a residue buildup.

VACATION, STORAGE, AND MOVING CARE

Install and store your Laundry Center where it will not freeze. Because some water may stay in the hoses, freezing can damage

your Laundry Center. If storing or moving your Laundry Center during freezing weather, winterize it.

Non=use or vacation care

Operate your Laundry Center only when you are at home. If you will be on vacation or not using your Laundry Center

for an extended period of time, you should:

[] Unplug Laundry Center or disconnect power. [] Turn off the water supply to the washer. This helps avoid

accidental flooding (due to a water pressure surge) while you are away.

To winterize Laundry Center L Shut off both water faucets.

2. Disconnect and drain water inlet hoses.

3. Put 1 qt (1 L) of R.V.-type antifreeze in the basket.

4. Run washer on a drain and spin setting for about 30 seconds to mix the antifreeze and water.

5. Unplug Laundry Center or disconnect power.

To use Laundry Center again

1. Flush water pipes and hoses.

2. Reconnect water inlet hoses.

3. Turn on both water faucets.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter.

Do not use an extension cord. Failure to foflow these instructions can result in death,

fire, or electrical shock.

4. Hug in Laundry Center or reconnect power.

5. Run the washer through a complete cycle with 1 cup (250 mL) of detergent to clean out antifreeze.

To transport the Laundry Center

1. Shut off both water faucets.

2. Disconnect and drain water inlet hoses.

3. If Laundry Center will be moved during freezing weather, put a qt (1 L) of R.V.-type antifreeze in the basket. Run washer

on a spin setting for about 30 seconds to mix the antifreeze and water.

40 Disconnect the drain hose from the drain system.

5. Unplug Laundry Center or disconnect power. Disconnect wiring if Laundry Center is direct wired (240 volt model only).

6. Disconnect the exhaust vent.

7. Wash lint screen.

80 Make sure leveling legs are secure.

90 Place the inlet hoses into the basket.

10. Place the foam packing ring (removed during installation) in the washer to keep the washer tub stable during transport.

11. Drape the power cord and drain hose over edge and into the basket.

12. Use tape to secure the washer lid and dryer door.

Reinstalling your Laundry Center

1. Follow the "Installation Instructions" to locate, level, and connect the Laundry Center.

2. Run the washer through a complete cycle with 1 scoop or capful of detergent to clean the washer and remove the

antifreeze, if used.

+ 78 hidden pages