Kenmore 110.7813*410 Use & Care Manual

Use & Care Guide
Manual de uso y cuidado

Guide d'utilisation et d'entrefien

English / Espa_ol / Franc;ais
Table of Contents...2 / {ndiced7 / Table des mati_res...34

Modek/Modelos/Mod(_les: 110.6813_410, 110.7813_410

110.6913_410, 110.7913_410

Ke

Electric or

h@us@

P/N W10680143D
Sears Brands Management Corporation

Hoffman Estates, IL 60179 U.S.A.
www.ken more.corn

www.sears.com
Sears Canada Inc.

Toronto, Ontario, Canada MSB 2C3
www.sears.ca

61ectrique ou

Dryer

@

© G

gGs

a 9az

TABLEOF CONTENTS

DRYER SAFETY .......................................................................... 2

CHECK YOUR VENT SYSTEM FOR GOOD AIR FLOW....4

USE SENSING CYCLES FOR BETTER FABRIC CARE

AND ENERGY SAVINGS ......................................................... 4

CONTROL PANEL AND FEATURES ....................................... 5

CYCLE GUIDE ............................................................................ 6

USING YOUR DRYER ............................................................... 8

DRYER SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

ADDITIONAL FEATURES ....................................................... 10

DRYER CARE ............................................................................. 11

TROUBLESHOOTING .............................................................. 13

PROTECTION AGREEMENTS ................................................ 16

WARRANTY .............................................................................. 16

ASSISTANCE OR SERVICE .................................... Back Cover

You can be killed or seriously injured if you don't immediately
follow instructions.

You can be killed or seriously injured if you don't follow

instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.

WARNING - ofFifo..

- Clothes dryer installation must be performed by a qualified installer,

- install the clothes dryer according to the manufacturer's instructions and local codes.

- Do not install a clothes dryer with flexible plastic venting materials or flexible metal

(foil type) duct. if flexible metal duct is installed, it must be of a specific type identified
by the appliance manufacturer as suitable for use with clothes dryers. Flexible venting

materials are known to collapse, be easily crushed, and trap lint. These conditions will
obstruct clothes dryer airflow and increase the risk of fire.

= To reduce the risk of severe injury or death, follow all installation instructions.
= Save these instructions.

State of California Proposition 65 Warnings:
WARNING: This product contains one or more chemicals known to the State of California to cause cancer.
WARNING: This product contains one or more chemicals known to the State of California to cause birth defects or other

reproductive harm.

2

IMPORTANT SAFETY INSTRUCTIONS

WARNING." To reduce the risk of fire, electric shock, or injury to persons when using the dryer, follow basic precautions,

including the following:

[] Read all instructions before using the dryer.
[] Do not place items exposed to cooking oils in your dryer.

Items contaminated with cooking oils may contribute to

a chemical reaction that could cause a load to catch fire.

[] Do not dry articles that have been previously cleaned in,

washed in, soaked in, or spotted with gasoline, dry-
cleaning solvents, or other flammable or explosive
substances as they give off vapors that could ignite or
explode.

[] Do not allow children to play on or in the dryer. Close

supervision of children is necessary when the dryer is
used near children.

[] Before the dryer is removed from service or discarded,

remove the door to the drying compartment.

[] Do not reach into the dryer if the drum is moving.
[] Do not install or store the dryer where it will be exposed

to the weather.

[] Do not tamper with controls.

[] Do not repair or replace any part of the dryer or attempt

any servicing unless specifically recommended in this
Use and Care Guide or in published user-repair

instructions that you understand and have the skills to
carry out.

[] Do not use fabric softeners or products to eliminate static

unless recommended by the manufacturer of the fabric
softener or product.

[] Do not use heat to dry articles containing foam rubber or

similarly textured rubber=like materials.

[] Clean lint screen before or after each load.
[] Keep area around the exhaust opening and adjacent

surrounding areas free from the accumulation of lint, dust,
and dirt.

[] The interior of the dryer and exhaust vent should be

cleaned periodically by qualified service personnel.

[] See "Electrical Requirements" located in the installation

instructions for grounding instructions.

SAVE THESE INSTRUCTIONS

WARNING: For your safety, the information in this manual must be followed to minimize I
the risk of fire or explosion, or to prevent property damage, personal injury, or death. |

- Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this
or any other appliance.

- WHAT TO DO iF YOU SMELL GAS:

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any phone in your building.
o Clear the room, building, or area of all occupants.
® Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's

instructions.

• if you cannot reach your gas supplier, caJl the fire department.

- InstaJJationand service must be performed by a qualified installer, service agency, or

the gas supplier.

WARNING: Gas leaks cannot always be detected by smell.
Gas suppliers recommend that you use a gas detector approved by UL or CSA.

For more information, contact your gas supplier.
If a gas leak is detected, follow the "What to do if you smell gas" instructions.

|

J

iMPORTANT: When discarding or storing your old clothes dryer, remove the door.

CHECK YOUR VENT SYSTEM FOR GOOD AiR FLOW

Fire Hazard

Use a heavy metal vent.
Do not use a plastic vent.

Do not use a metal foil vent.
Failure to follow these instructions can result in death

or fire,

Good Air Flow

Along with heat, dryers require good air flow to efficiently
dry laundry. Proper venting will reduce your drying times and

improve your energy savings. See installation instructions.
The venting system attached to the dryer plays a big

role in good air flow. Blocked or crushed vents as well as
improper venting installation will reduce air flow and dryer

performance.
Service calls caused by improper venting are not covered by

the warranty and will be paid by the customer, regardless of
who installed the dryer. To clean or repair venting, contact a

venting specialist.

B w

rMaintain good air now by:

[] Cleaning your lint screen before each load.
[] Replacing plastic or foil vent material with 4" (102 mm)

diameter heavy, rigid vent material.

[] Using the shortest length of vent possible.
[] Using no more than four 90 ° elbows in a vent system;

each bend and curve reduces air flow.

.............................Bett

[] Removing lint and debris from the exhaust hood.
[] Removing lint from the entire length of the vent system

at least every 2 years. When cleaning is complete,

be sure to follow the "installation instructions" supplied

with your dryer for final product check.

[] Clearing away items from the front the dryer.

Use sensing cyc(es for better fabric care and energy savings

Use the Sensing Cycles to get the most energy savings and enhanced fabric care from the dryer. During Sensing Cycles, drying
air temperature and moisture level are sensed in the load. This sensing occurs throughout the drying cycle and the dryer shuts off

when the load reaches the selected dryness. Choose Normal cycle to save energy.
With Timed Cycles, the dryer runs the amount of time set and sometimes results in shrinkage, wrinkling, and static due to

overdrying. Use Timed Cycles for the occasional damp load that needs a little more drying time or when using the drying rack.

4

STEAM MODEL

NON-STEAM MODEL

CONTROL

ID

Heavy Duty

Bulky IBeddin

POWER

TIMED CYCLES

Timed Dry

'

Heavy Duty

...... % ii!i::

PowE_ _ E]p.... ................

Not all features and options are available on all models. Appearance may vary.

POWER BUTTON

@

Touch to turn the dryer on and off. Touch to stop/cancel
a cycle at any time.

CYCLE KNOB

@

Use your cycle knob to select available cycles on your dryer.
Turn the knob to select a cycle for your laundry load. See

"Cycle Guide" for detailed descriptions of cycles.

Timed Cycles

Will run the dryer for the specified time on the control. On

models with a selectable temperature buffon, you may choose
a setting based on the fabrics in your load. Drying time and
temperature will vary depending on your dryer model.

Sensing Cycles

Sensing cycles give the best drying in the shortest time.

Drying time will vary based on fabric type, load size,
and dryness setting.

LED DISPLAY AND SETTINGS

O

When you select a cycl% its default settings will light up and
the Estimated Time Remaining (for Sensing Cycles) or actual
time remaining (for Timed Cycles) will be displayed.

Touch the setting names next to the display to adjust settings.
See "Cycle Guide" for available settings on each cycle. Not
all settings are available with all cycles.

Dry Temp

Select a drying temperature based on the fabrics in
your load. if you are unsure of the temperature to select
for a load, select the lower setting rather than the higher
setting. See "Cycle Guide."

NOTE: Sensing Cycles allow temperature adjustment. At most,
3 of the available temperatures (not including Air) are allowed.

Dry Level

You may adjust the Dry Level on Sensing Cycles (except
for the Sanitize cycle) if desired.

NOTE: Dry Level is for use with Sensing Cycles only.

Cycle Signal

The Cycle Signal produces an audible sound when the
drying cycle is finished. Promptly removing clothes at the
end of the cycle reduces wrinkling.

TIMED CYCLES _. PAUSE

Timed Dry Touch Up |

NOTE: When the Wrinkle Guard TM option is selected and
the Cycle Signal is on, the tone will sound at 15 minutes,
30 minutes, and at the end of Wrinkle Guard TM.

NOTE: You may also turn off the tones that sound when
a cycle is selected, or when a feature or option is touched.

Touch and hold CYCLE SIGNAL for about three seconds
to turn sounds off or on.

Time Adjust for Timed Cycles Only

Use "+" and "-" with Timed Cycles to increase or decrease
the length of a Timed Dry or Express cycle.

OPTIONS

Use to select available options for your dryer. Not all cycles
and options are available on all models.

Energy Saver option

Activate the ENERGY SAVER setting to increase your
energy savings. This setting uses a lower heat level and
extends cycle time. Turn on for optimal energy savings.
Turn off for optimal cycle times. ENERGY SAVER will

default on for Normal.
NOTE: Energy savings are not available on all cycles and

may vary across loads and cycles.

Wrinkle Guard TM or WHnk[e Guard TM w/Steam
option (depending on model)

When you are unable to remove a load of clothes from
the dryer as soon as it stops, wrinkles can form. The
Wrinkle Guard TM option periodically tumbles, rearranges,
and fluffs the load to help keep wrinkles from forming. The

Wrinkle Guard TM w/Steam setting (depending on model)
will add a short steam cycle after 60 minutes to help
smooth out wrinkles.

[] Get up to 150 minutes of heat-free, periodic tumbling

at the end of a cycle. Touch the WRINKLE GUARD TM
option to select ON or OFF at any time before the
cycle has ended.

NOTE: If you open the dryer door prior to the end of
the Wrinkle Guard TM option, the dryer will go into Pause

mode. You will need to touch Power to turn off or touch
Start/Pause to continue Wrinkle Guard TM option.

Damp Signal

Touch to select the Damp Signal to On or Off. When

selected, a series of beeps will sound when the load is

damp but not completely dry. This will allow you to take

clothes out of the load that do not need to dry completely.

This option is not available on Sanitize, Steam Refresh,

and the Timed cycles.

CYCLE STATUS LIGHTS

O

The indicator bar on the right side of the control will let you
know what stage of the drying cycle is in process.

Check Vent

The Check Vent indicator will light if there is a blocked

vent or low airflow.

Damp

This indicator shows that the load is partially dried

and items that you may wish to hang up or iron while

still damp may be removed.

Cool Down

@

Complete

This will indicate that the selected cycle has ended and
the load may be removed from the dryer. If Wrinkle
Guard TM option has been selected, the dryer may continue
to tumble the load, even if the Complete indicator is lit.

Wrlnkle Guard TM

This indicator will light if the Wrinkle Guard TM option has
been selected and is running. The dryer will periodically
tumble the load for up to 150 minutes after the cycle has

ended.

Check Lint Screen

The Check Lint Screen indicator light will flash as a
reminder to clean the lint screen. It will flash until the

door is opened or a cycle is started. It will turn off when
the dryer is turned off.

START/PAUSE BUTTON

Touch and hold START/PAUSE button for up to 3 seconds
or until the dryer starts to begin the selected cycle; touch

again to pause a cycle.

The dryer has finished drying with heat, and is now

tumbling the load without heat to cool it down and

reduce wrinkling.

CYCLE GUIDE -SENSING CYCLES

SENSING CYCLES - Senses moisture in the load and shuts off when the load reaches the selected dryness level. The dry temperature

shown is the default temperature. This setting can be modified on some cycles but is not retained for future drying with this cycle. The
dryness level shown is the default dryness setting. This setting can be changed on some cycles and will be retained for future drying with
this cycle. Available options shown in bald are default settings for that cycle.

To get the most energy savings and enhanced fabric care from your dryer, use the Sensing cycles. These cycles measure the drying
air temperature and moisture levels to turn the dryer off once the load reaches the selected dryness level. For electric models, dryer
performance and results may vary with service voltage less than 240.

Towels and
bedding

Sanfize _

i •

Air Medium High

Less Normal More

Wrinkle Guard TM

Cycle Signal

Extended high-heat drying cycle intended
to help sanitize items such as bedding and
towels. This cycle is not recommended for
all fabrics. For best results, run cycle to
completion, do not interrupt.

NOTE: Steam portion of Wrinlde Guard TM

w/Steam option is disabled for this cycle.

Jackets,

comforters, pillows

Bulky/

Bedding

i O

Air Medium High

Less Normal More

Damp Dry Signal
Wrinkle Guard TM

Use for drying large, bulky items; do not
overfill dryer drum.

Cycle Signal

Heavyweight items
such as towels and

jeans

Corduroys, work

clothes

Heavy

Duty

Normal

Air Medium High

Air Medium High

i[ O

Less Normal More

Less Normal More

Damp Dry Signal
Wrinkle Guard TM

Cycle Signal

Damp Dry Signal

Energy Saver

Wrinkle Guard TM

Use for drying large or heavy items.

Medium to large loads of mixed fabrics
and items.

Cycle Signal

No-iron fabrics,
cottons, perm
press, linens,
synthetics

Lingerie, blouses,
washable knit

fabrics

Casual

Delicates

_i! !9 • _iiii iiiiii_

Air Medium High

0 r

Air Medium High

Less Normal More

Less Normal More

Damp Dry Signal

Energy Saver

Wrinkle Guard TM

Cycle Signal

Damp Dry Signal

Energy Saver

Wrinkle Guard TM

For normal light- to medium-weight
fabrics. Drying time varies based on
fabric type, load size, and dryness setting.

For gently drying delicate items.

NOTE: Steam portion of Wrinlde Guard TM

w/Steam option is disabled for this cycle.

Cycle Signal

Extended high-heat drying cycle intended to help sanitize items such as sheets and towels. This cycle is not recommended for all
fabrics. For best results, this cycle should be run to completion to ensure sanifization and do not interrupt cycle.

If loads do not seem as dry as you would like or are drier than you would like, select More Dry or Less Dry next time you dry

a similar load.

6

CYCLE GUIDE - TIMED CYCLES

TIMED CYCLES- Will run the dryer for the specified time on the control. Settings shown are default settings for that cycle.

Any load Timed Dry 40 Wrinkle Guard TM_ Select a drying temperature based on the fabrics in your

Cycle Signal load. If you are unsure of the temperature to select for a

Any load Touch Up 20 Wrinkle Guard TM_ Use this cycle to quickly refresh an item or remove light

Cycle Signal wrinkles. The load is cooled slowly to reduce wrinkling and

Small loads and Express 15 Wrinkle Guard TM_ For small loads of 2-3 items.
sportswear (2 to Cycle Signal
3 items)

_;Depending on settings, steam option may be disabled to protect clothing and optimize performance.

load, select the lower setting rather than the higher setting.

make it easier to handle.

CYCLE GUIDE - STEAM CYCLE

STEAM CYCLE- Designed for use with dry loads to loosen wrinkles, reduce odors, and refresh fabrics.

Settings shown are default settings for that cycle. Not all settings and options are available on each cycle.

Mixed loads Steam

Refresh

O {

Air Medium High

Less Normal More

Setting the Dry Temp

Select a drying temperature based on the fabrics in your load.
If you are unsure of the temperature to select for a load, select

the lower setting rather than the higher setting.

Temperature Tips

[] A High heat setting may be used for drying heavyweight

items such as towels and work clothes.

[] A Medium to Medium High heat setting may be used

for drying medium-weight items such as sheets, blouses,
dresses, underwear, permanent press fabrics, and some

knits.

Wrinkle Guard TM

Cycle Signal

[] A Low heat setting may be used for drying lightweight

items such as lingerie.

[] Use an Air (no heat) setting for foam, rubber, plastic,

or heat-sensitive fabrics.
[] Line dry bonded or laminated fabrics.
NOTE: If you have questions about drying temperatures

for various loads, refer to the care label directions.

Use to smooth out wrinkles and reduce
odors from loads consisting of 2 to 4

dry items of wrinkle-free cotton, cotton-
polyester blend, common knits, and
synthetic garments.

USING YOUR DRYER

Explosion Hazard

Keep flarrnrnabie materials and vapors, such as

gasoline, away from dryer.

Do not dry anything that has ever had anything

flammable on it (even after washing).

Failure to follow these instructions can result in death,

explosion, or fire.

WARNING: To reduce the risk of fire, electric shock, or injury

to persons, read the IMPORTANT SAFETY INSTRUCTIONS

before operating this appliance.

Fire Hazard

No washer can completely remove oil.

Do not dry anything that has ever had any type of oil on
it (including cooking oils).

items containing foam, rubber, or plastic must be dried
on a clothesline or by using an Air Cycle.

Failure to follow these instructions can result in death
or fire.

f3. Touch Power

POWER

Touch POWER to turn on the dryer.

CJean the lint screen before each load. Pull the lint screen
straight up and out. Press tab down on front to open lint screen.

Roll lint off the screen wffh your fingers. Do not rinse or wash
screen to remove lint. Wet lint is hard to remove. CJose lint

screen and push the lint screen firmly back into place.
For additional cleaning information, see "Dryer Care."

2. Load the dryer

m m

Place laundry in the dryer. Close the door. Do not tightly pack
the dryer; clothes should be able to tumble freely.

8

4. Select the desired cycle
Normal

Heavy Duty Casual

;iiiiii_ !iiii/

Bulky l Bedding Delicates

f6. Select any additional options

w/(_bSteam

Sanitize S a efresh

SENSING CYCLES

TIMED CYCLES

® @

Timed Dry Touch Up

Steam model shown

Select the desired cycle for your load. See the "Cycle Guide"
for more information about each cycle.

Steam Refresh:

Reduces light wrinkles and odors from a few garments at a
time. Do not add dryer sheets.

tear

@

Express

5. Set cycle settings, if desired

m

LT. J

TIMED CYCLSS ONLY

Air Medium High

iiiiii_ iiiiiii_ _iiiiii iiiWi_ _iii__¸

SENSINGCYCLESONLY

You may adiust different settings, depending on whether you
have selected a Sensing Cycle, Timed Cycle, or Steam Refresh
Cycle. See the "Cycle Guide" for detailed information.

NOTE: Not all options and settings are available with all cycles.
Not all cycles are on all models.

Sensing Cycles:

You can select a different dryness level, depending on your
load, by touching DRY LEVEL to scroll to More, Normal, or

Less. Selecting More, Normal, or Less automatically adjusts the
dryness level at which the dryer will shut off. Dry Level can be

changed in the first 5-8 minutes of the cycle. Sensing cycles give
the best drying in the shortest time. Drying time varies based on

fabric type, load size, and dryness setting.
NOTE: More Dry removes more load moisture. Normal Dry is

used for a starting point for Sensing cycles. Choose normal to
save energy. Less Dry removes less moisture and used for loads
you may want to put on a hanger to complete drying.

Timed Cycles:
When you select a Timed Cycle, the default time appears in

the display. Touch "+" and "-" to increase or decrease the time
in 1-minute increments. Touch and hold to change the time in

5-minute increments. The default temperature may be changed
by touching Dry Temp until the desired dry temperature is lit.

Less Normal More

_o_

Add additional options such as Energy Saver or Damp Signal
by touching that option. If you will be unable to remove the

load promptly, select the Wrinkle Guard TM options before
touching START.

High

Wrinkle Guard TM or Wrinkle Guard TM w/Steam

option (dependlng on model)

When you are unable to remove a load of clothes from the
dryer as soon as it stops, wrinkles can form. The Wrinkle

Guard TM option periodically tumbles, rearranges, and fluffs the
load to help keep wrinkles from forming. The Wrinkle Guard TM

w/Steam setting (depending on model) will add a short steam
cycle after 60 minutes to help smooth out wrinkles. Get up to

150 minutes of heat-free, periodic tumbling at the end of a
cycle. Touch the WRINKLE GUARD TM button to select ON or
OFF at any time before the cycle has ended.

NOTE:
[] When the Wrinkle Guard TM option is selected and the

Cycle Signal is on, the tone will sound at 15 minutes,
30 minutes, and at the end of Wrinkle Guard TM.

[] If you open the dryer door prior to the end of the Wrinkle

Guard TM option, the dryer will go into Pause mode. You
will need to touch Power to turn off or touch Start/Pause to

continue Wrinkle Guard TM option.

fT. Touch and hold START/PAUSE to

begin cycle

HOLDTO

START

PAUSE

Touch and hold the START/PAUSE button to begin the cycle.
Promptly remove items after cycle has completed to reduce

wrinkling. Use the Wrinkle Guard TM option to avoid wrinkling
when you are unable to remove a load from the dryer as soon
as it stops.

the Sensing Cycle settings

to increase or decrease drying time

If all your loads on all Automatic Cycles are consistently less dry
or more dry than you would like, you may change the default

settings to increase or decrease the default dryness level.
Your automatic drying settings can be adjusted to adapt to

different installations, environmental conditions, or personal
preference. This change is retained and will affect all of your

Automatic Cycles, not just the current cycle/load. There are
5 drying settings, which are displayed using the time display:

0 Much wetter clothes, 30% less drying time.

I Slightly wetter clothes, 15% less drying time.

2 Factory preset dryness level.
3 Slightly drier clothes, 15% more drying time.

4 Much drier clothes, 30% more drying time.

To change the drying settings:

NOTE: The settings cannot be changed while the dryer
is running or paused. The dryer must be in standby mode

(power is off) to adjust the default settings.

1. Before starting a cycle, touch and hold DRY LEVEL
for 3 seconds.

2. Touch DRY LEVEL to select the dryness level shown in the
time display: 0, 1, 2, 3, or 4.

3. Touch START/PAUSE to save the new dryness level setting.

ADDiTiONAL FEATURES

Using the Drying Rack

To obtain a drying rack for your dryer, order by calling
1-800-469-4663. You will need your model and serial

number and the purchase date. Remove and discard any
packing material before use.

Use the Drying Rack for items that you do not want to tumble
dry, such as sweaters and tennis shoes. When you use the

drying rack, the drum continues to turn, but the rack remains

stationary.

The drying rack is intended for use with the Timed Cycles
only. The drying rack cannot be used with Sensing/Automatic

Cycles.
To use the drying rack:

IMPORTANT: Do not remove the lint screen.

1. Open dryer door.

Using the Drying Rack (cont.)

2. Align the two hooks on the front of the drying rack with the
holes in the dryer door opening and press down fully into
holes. Rest the rear support on the dryer back ledge.

Place wet items on top of the drying rack. Allow space
around items for air to circulate. The drying rack does not
move, but the drum will rotate; be sure to leave adequate

clearance between items and the inside of the dryer drum.
Make sure items do not hang over the edges or between

drying rack grille.
Close the door.

Select a Timed Dry!Air Only, or Low Temperature cycle.
Items containing foam, rubber, or plastic must be dried

on a clothesline or by using the Air Only setting.

6. When the cycle is selected, the Estimated Time Remaining
display shows the default time. You can change the actual

time in the cycle by increasing or decreasing the cycle time.

7. Start the dryer.

NOTE: Check the lint screen and remove any lint accumulated
from items dried on the drying rack after the cycle is finished.

I0

DRYER CARE

Explosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from dryer.

Place dryer at least 18 inches (460 turn) above the floor

for a garage installation.

Failure to do so can result in death, explosion, or fire.

fCleaning the dryer interior

To clean dryer drum

I. Apply a liquid, nonflammable household cleaner to the

stained area of the drum and rub with a soft cloth until
stain is removed.

2. Wipe drum thoroughly with a damp cloth.

3. Tumble a load of clean cloths or towels to dry the drum

OR

Use a microfiber cloth and hot water in a spray bottle to

clean the drum and a second mJcrofiber towel to dry.

NOTE: Items that contain loose dyes, such as denim blue
jeans or brightly colored cotton items, may discolor the dryer
interior. These stains are not harmful to your dryer and wJJJ
not stain future loads of clothes. Dry these items inside out
to avoid drum staining.

f

Removing accumulated lint

From Inslde the Dryer Cabinet

Lint should be removed every 2 years_ or more often,

depending on dryer usage. Cleaning should be done

by a qualified servicer.

From the Exhaust Vent

Lint should be removed every 2 years_ or more often_

depending on dryer usage.

_Cleaning the lint screen

Every load cleanlng

The lint screen is located in the door opening of the dryer.
The control panel has an indicator light _'Check Lint Screen"

to remind you to clean the lint screen after each load. A

screen blocked by lint can increase drying time.

To clean:

1. Pull the lint screen straight up and out. Press tab down on
front to open lint screen. Roll lint off the screen with your

fingers. Do not rinse or wash screen to remove lint. Wet

lint is hard to remove.

2. Close the lint screen and push firmly back into place.

iMPORTANT:

[] Do not run the dryer with the lint screen loose, damaged,

blocked, or missing. Doing so can cause overheating and

damage to both the dryer and fabrics.

[] If lint falls off the screen into the dryer during removal,

check the exhaust hood and remove the lint. See "Venting

Requirements" in the Installation Instructions.

[] Clean space where lint screen I-/"I I _\Jf///_

is located, as needed. Using a

vacuum, gently remove any lint
that has accumulated outside

of the lint screen.

As needed cleaning

Laundry detergent and fabric softener residue can build up

on the lint screen. This buildup can cause longer drying times
for your clothes or cause the dryer to stop before your load

is completely dry. The screen is probably clogged if lint falls

off while the screen is in the dryer.

Clean the lint screen with a nylon brush every 6 months,

or more frequently, if it becomes clogged due to a residue

buildup.

To wash:

1. Roll lint off the screen with your fingers.

2. Wet both sides of lint screen with hot water.

3. Wet a nylon brush with hot

water and liquid detergent. Scrub

lint screen with the brush to remove
residue buildup.

4. Rinse screen with hot water.

5. Thoroughly dry lint screen
with a clean towel.

Reinstall screen in dryer.

11

storage, and moving care

Steam models only: Install and store your dryer where it
will nat freeze. Because some water may stay in the hose,

freezing can damage your dryer. If storing or moving your
dryer during freezing weather, winterize it.

Non-Use or Storage Care
Operate your dryer only when you are at home. if you will

be on vacation or not using your dryer for an extended
period of time, you should:

1. Unplug dryer or disconnect power.

2. Clean lint screen. See "Cleaning the Lint Screen."

3. Turn off the water supply to the dryer. This helps to avoid

unintended flooding (due to a water pressure surge)
while you are away.

Moving Care
For power supply cord-connected dryers:

1. Unplug the power supply cord.

2. Gas models only: Close shut-off valve in gas supply line.

3. Gas models only: Disconnect gas supply line pipe and

remove fittings attached to dryer pipe.

4. Gas models only: Cap the open fuel supply line.

5. Steam models only.. Shut off water faucet.

6. Steam models only.. Disconnect the water inlet hose from
faucet, then drain the hose. Transport hose separately.

Z Make sure leveling legs are secure in dryer base.

8. Use tape to secure dryer door.

Electrical Shock Hazard

Disconnect power before servicing.
Replace all parts and panels before operating.

Failure to do so can result in death or electrical shock,

For direct-wired dryers:
L Disconnect power.

2. Disconnect wiring from dryer and secure wire ends.

3. Steam models only: Shut off water faucet.

4. Steam models only: Disconnect the water inlet hose from
faucet; then drain the hose. Transport hose separately.

5. Make sure leveling legs are secure in dryer base.

6. Use tape to secure dryer door.

Reinstalling the Dryer
Follow the Installation Instructions to locate, level, and connect

the dryer.

F SPECIAL iNSTRUCTiONS

FOR STEAM MODELS

Water Inlet Hose

Replace inlet hose and hose screen after 5 years of use
to reduce the risk of hose failure. Periodically inspect and
replace inlet hose if bulges, kinks, cuts, wear, or leaks

are found.

When replacing your inlet hose, record the date

of replacement.

To Winterize the Dryer
L Unplug dryer or disconnect power.

2. Shut off water faucet.

3. Disconnect water inlet hose from faucet and drain.

To Use the Dryer Again

1. Flush water pipes. Reconnect water inlet hose to faucet.
Turn on water faucet.

2_

Plug in dryer or reconnect power as described in the
Installation Instructions.

12

r

If you experience

TROUBLESHOOTING

First try the solutions suggested here for assistance and to possibly avoid a service call.

Possible Causes Solution

Dryer will not run

Dryer will not turn off

Dryer will not heat

Humming or whining noise

with Steam cycle selected

Thumping noise

Rattling or vibrating noise

Clicking noise

Door not closed completely.

START/PAUSE touched with fingernail
or not touched long enough.

Household fuse is blown, circuit
breaker has tripped, or dryer is not

plugged in.

Incorrect power supply.

Wrong type of fuse.

Dryer door was opened prior to the

end of the Wrinkle Guard TM option.

Household fuse is blown or circuit
breaker has tripped.

Incorrect power supply.

The gas supply line valve not open.

Water inlet valve on dryer is running.

Dryer hasn't been used in a while.

A small object caught between the
edges of dryer drum.

Dryer isn't properly leveled.

Clothing is balled up in dryer.

Gas valve operating.

Make sure the dryer door is closed completely.
Touch and hold START/PAUSE for up to 3 seconds with pad of

finger.
There may be 2 household fuses or circuit breakers for the dryer.

Check that both fuses are intact and tight or that both circuit

breakers have not tripped. Replace the fuses or reset the circuit
breaker. If the problem continues, call an electrician.

Electric dryers require 240-volt or 208-volt power supply. Check
with a qualified electrician.

Use a time-delay fuse.

If you open the dryer door prior to the end of the Wrinkle

Guard TM option, the dryer will go into Pause mode. You will
need to touch Power to turn off or touch Start/Pause to continue

Wrinkle Guard TM.
The drum may be turning, but you may not have heat. Electric

dryers use 2 household fuses or circuit breakers. Replace the
fuses or reset the circuit breaker. If the problem continues, call
an electrician.

Electric dryers require 240-volt or 208-volt power supply. Check
with a qualified electrician.

For gas dryers, make sure that the valve on the gas supply line is
open.

The water pump on the dryer is used during the Steam function.

If the dryer has just been installed or unused for an extended

period, the pump may be louder and run longer. This is normal.
This is normal. The thumping sound should diminish after a few

minutes of use.
Check the front and rear edges of the drum for small objects.

Clean out pockets before laundering.
The dryer may vibrate if not properly installed. See the Installation

Instructions. All four dryer feet should be in firm contact with the

floor.
When balled up, the load will bounce, causing the dryer to

vibrate. Separate the load items and restart the dryer.
On gas dryers, you may hear the gas valve clicking as it opens

and closes. This is normal.

Clothes are not drying Lint screen or lint screen housing is Clean lint screen before each load. Clean space where lint screen
satisfactorily, clothes are clogged with lint. is located, as needed. Using a vacuum, gently remove any lint

bailing or tangling, or that has accumulated outside of the lint screen.

drying times are too long The exhaust vent or outside exhaust Run the dryer for 5-10 minutes. Hold your hand under the

hood is clogged with lint, restricting outside exhaust hood to check air movement. If you do not feel

air movement, air movement, clean exhaust system of lint or replace exhaust

The exhaust vent is not the correct Check that the exhaust vent is not too long or has too many

length, turns. Long venting will increase drying times. See the Installation

The exhaust vent diameter is not the Use 4" (102 ram) diameter vent material.
correct size.

The dryer is not level. Clothes not contacting the moisture sensors during Sensing Cycles.

The Air Dry Temp setting has been Select the correct temperature for the types of garments being
selected, dried. See "Cycle Guide."

vent with heavy metal or flexible metal vent. See the Installation

Instructions.

Instructions.

See "Level Dryer" in the Installation Instructions.

13

TROUBLESHOOTING

First try the solutions suggested here for assistance and to possibly avoid a service call.

Solution

Clothes are not drying The load is too large and heavy to
satisfactorily, clothes are dry quickly.

bailing or tangling, or Fabric softener sheets are blocking The air outlet grille is just inside the door, behind the lint screen.

drying times are too long the grille. Check that it is not blocked by a fabric softener sheet. Use only

(cont.) one fabric softener sheet, and use it only once.

The dryer is located in a room with Proper operation of dryer cycles requires temperatures above
temperature below 45°F (7°C). 45°F (7°C).

The dryer is located in a closet. Closet doors must have ventilation openings at the top and

Cycle time is too short The load may not be contacting the Level the dryer. See the Installation Instructions. All four dryer feet

sensor strips on Sensing Cycles. should be in firm contact with the floor.

Clothes are coming out of the Steam If you are doing a Steam Refresh cycle of 1 or 2 items you can

Refresh cycle with damp or wet spots, add a towel to the load to help avoid uneven spraying from the

The sensing cycle is ending early. Change the dryness level setting on Sensing Cycles. Increasing or

Lint on load Lint screen is clogged with lint. Clean lint screen before each load.

Stains on load Improper use of fabric softener.

Stains on drum Loose dyes in clothes.

Loads are wrinkled The load was not removed from dryer

at the end of the cycle.

The dryer was tightly packed.

For steam cycles, the water is not
properly connected with the dryer.

Odors Recent painting, staining, or varnishing

Steam did not occur Wrinkle Guard TM does not Refer to Cycle Guide to verify which cycles and settings enable

during Wrinkle Guard TM enable Steam on all cycle/option Steam.

in the area where your dryer is

located.
For steam cycles, the water is not Make sure water is connected to the dryer. Check that water inlet

properly connected with the dryer, hose is connected to both the faucet and dryer's water inlet valve.

Odors are left in garments after To remove odors left in garments after wearing, select Steam
wearing. Refresh. This cycle is best for reducing wrinkles and odors from

combinations.

Separate the load to tumble freely.

bottom of the door. The front of the dryer requires a minimum of
1" (25 ram) of airspace, and, for most installations, the rear of the
dryer requires 5" (127 ram). See the Installation Instructions.

steam valve. Then select the appropriate time based on the load
to be refreshed.

decreasing the dryness level will change the amount of drying
time in a cycle. If loads are consistently ending too early, see also
"Changing the Sensing Cycle settings to increase or decrease
drying time."

Add dryer fabric softener sheets at the beginning of the cycle.
Fabric softener sheets added to a partially dried load can stain
your garments. Do not use fabric softener sheets with steam
cycles.

Drum stains are caused by dyes in clothing (usually blue jeans).
These will not transfer to other clothing.

Select Steam Refresh cycle to tumble the load with water and

heat. This cycle is best for smoothing out wrinkles and reducing

odors from dry loads consisting of wrinkle-free cotton, cotton-

polyester blends, common knits, and synthetics.

NOTE: Refer to garment care label instructions. Dry-clean-only
garments are not recommended.

Dry smaller loads that can tumble freely. Results may also vary
depending on fabric type.

AAake sure water is connected to the dryer. Check that water inlet
hose is connected to both the faucet and dryer's water inlet valve.
Check that the water supply is turned on.

Ventilate the area. When the odors or fumes are gone from the
area, rewash and dry the clothing.

Check that the water supply is turned on.

dry loads consisting of wrinkle-free cotton, cotton-polyester
blends, common knits, and synthetics.

14

if you experience

TROUBLESHOOTING

First try the solutions suggested here for assistance and to possibly avoid a service call.

] Possib,e Cc=uses ! So,ution

Load too hot

"PF" (power failure)

"L2" Diagnostic Code
(low or no line voltage

condition)

"-=" Cycle knob is not on cycle.

"Check Vent" cycle
status indicator lights
up (blocked vent or low

airflow condition)

"F# E#" (F1 El, F3 El, The dryer is in need of service.

etc.) variable service

codes.

Load removed before cool down

portion of cycle complete.
Using Timed Dry cycle with a high

temperature setting.

The drying cycle has been interrupted

by a power failure.

There may be a problem with your

home power supply, keeping the

dryer's heater from turning on.

The lint screen or vent is clogged;
the vent is crushed, kinked or has

too many turns.

Allow the dryer to complete the cool down portion of the cycle

before removing the load.

Select a Sensing Cycle with a lower heat setting to avoid
overdrying the load.

Touch the START key to clear the PF error message; then press and

hold the START key to resume cycle.

The dryer will continue to run when this diagnostic code is present.
Touch any pad to clear the code from the display and return to

the estimated time remaining.
Try the following:
* Check to see if a household fuse has blown or circuit breaker

has tripped. Electric dryers use two household fuses or breakers.
Replace the fuse or reset the circuit breaker.

" Confirm that the power cord is properly installed. Refer to

the Installation Instructions for details.
Select a Timed Dry heated cycle, and restart the dryer.

If the message persists, consult a qualified electrician.

This is not an error. The selector knob is not on a cycle. Rotate
your selector knob until a cycle lights up.

The dryer will continue to run when this diagnostic code is present.
Touch any key to clear the code from the display and return to

the estimated time remaining.
Try the following:

" Clean lint screen.
" Check to see if the vent run from the dryer to the wall is

crushed or kinked.

" Confirm that the vent run from the dryer to the wall is free

of lint and debris.

" Confirm that the exterior vent exhaust hood is free of lint

and debris.

" Confirm that your vent system falls within the recommended

run length and number of elbows for the type of vent you are
using. Refer to "Plan Vent System" in the Installaton Instructions

for details.

Select a Timed Dry heated cycle, and restart the dryer.

If the message persists, have your entire home venting run

cleaned. Contact a venting specialist.

If a code beginning with an "F" appears in the display, alternating

between F# and E#, the dryer control has detected a problem
that requires service. Call for service.

15

PROTECTION AGREEMENTS

Master Protection Agreements

Congratulations on making a smart purchase. Your new Kenmore ®
product is designed and manufactured for years of dependable

operation.

But like all products, it may require preventive maintenance or
repair from time to time. That's when having a Master Protection

Agreement can save you money and aggravation.

The Master Protection Agreement also helps extend the life

of your new product. Here's what the Agreement _ includes..

Parts and labor needed to help keep products operating properly
under normal use, not just defects. Our coverage goes well

beyond the product warranty. No deductibles,no functional

failure excluded from coverage--real protection.

Expert service by a force of more than 10,000 authorized Sears

service technicians, which means someone you can trust will be

working on your product.

Unlimited service coils and nationwide service, as often as you

want us, whenever you want us.

- replacement of your covered product if four or more product
failures occur within twelve months.

Product replacement if your covered product can't be fixed.

Annual Preventive Maintenance Check at your request -

no extra charge.
Fast help by phone - we call it Rapid Resolution - phone support

from a Sears representative on all products. Think of us as a

"talking owner's manual."

Power surge protection against electrical damage due

to power fluctuations.

Rental reimbursement if repair of your covered product takes
longer than promised.

25% discount off the regular price of any non-covered repair

service and related installed parts.

Once you purchase the Agreement, a simple phone call is all
that it takes for you to schedule service. You can call anytime
day or night, or schedule a service appointment online.

The Master Protection Agreement is a risk free purchase. If you
cancel for any reason during the product warranty period, we
will provide a full refund. Or, a prorated refund anytime after the

product warranty period expires. Purchase your Master Protection
Agreement today! Some limitations and exclusions apply.

For prices and additional information in the U.S.A., call

1-800-827-6655. _Coverage in Canada varies on some items.

For full details, call Sears Canada at 1-800-361-6665.

Sears Installatlon Service

For Sears professional installation of home appliances, garage
door openers, water heaters, and other major home items,

in the U.S.A. or Canada, call 1-800-4-MY=HOME ®.

KENMORE APPLIANCE WARRANTY

KENMORE LIMITED WARRANTY 7. Damage to or failure of this appliance, including discoloration

FOR ONE YEAR from the date of sale this appliance is warranted

against defects in material or workmanship when it is correctly

installed, operated, and maintained according to all supplied
instructions.

WITH PROOF OF SALE, a defective appliance will receive free

repair or replacement at option of seller.
For warranty coverage details to obtain free repair or

replacement, visit the web page: www.kenmore.com/warranty.
This warranty applies for only 90 DAYS from the sale date in the

United States, and is void in Canada, if this appliance is ever used

for other than private household purposes.
This warranty covers ONLY defects in materlal and

workmanship, and will NOT pay for:

1. Expendable items that can wear out from normal use, including
but not limited to filters, belts, bags, or screw-in base light
bulbs.

2. A service technician to clean or maintain this appliance, or to
instruct the user in correct appliance installation, operation, and

maintenance.

3. Service calls to correct appliance installation not performed
by Sears authorized service agents, or to repair problems with

house fuses, circuit breakers, house wiring, and plumbing or gas
supply systems resulting from such installation.

4. Damage to or failure of this appliance resulting from
installation not performed by Sears authorized service agents,

including installation that was not in accord with electrical, gas,

or plumbing codes.

5. Damage to or failure of this appliance, including discoloration

or surface rust, if it is not correctly operated and maintained
according to all supplied instructions.

6. Damage to or failure of this appliance, including discoloration

or surface rust, resulting from accident, alteration, abuse, misuse
or use for other than its intended purpose.

or surface rust, caused by the use of detergents, cleaners,
chemicals, or utensils other than those recommended in all

instructions supplied with the product.

8. Damage to or failure of parts or systems resulting from
unauthorized modifications made to this appliance.

9. Service to an appliance if the model and serial plate is missing,
altered, or cannot easily be determined to have the appropriate

certification logo.

DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION
OF REMEDIES

Customer's sole and exclusive remedy under this limited warranty
shall be product repair or replacement as provided herein. Implied

warranties, including warranties of merchantability or fitness
for a particular purpose, are limited to one year or the shortest

period allowed by law. Seller shall not be liable for incidental

or consequential damages. Some states and provinces do not
allow the exclusion or limitation of incidental or consequential

damages, or limitation on the duration of implied warranties of

merchantability or fitness, so these exclusions or limitations may
not apply to you.

This warranty applies only while this appliance is used in the
United States or Canada _.

This warranty gives you specific legal rights, and you may also
have other rights which vary from state to state.

In-home repair service is not available in all Canadian

geographical areas, nor will this warranty cover user or servicer
travel and transportation expenses if this product is located

in a remote area (as defined by Sears Canada Inc.) where an

authorized servicer is not available.

Sears Brands Management Corporation

Hoffman Estates, IL 60179

Sears Canada inc.

Toronto, Ontario, Canada M5B 2C3

16

10/2014