Kenmore 11062972101, 11062972102, 11062974101, 11062982101, 11062982102 Installation Guide

...

27 IN. (69CM) ELECTRIC DRYER

INSTALLATION INSTRUCTIONS

INSTRUCCIONE.S DE INSTALACION PARA LA

SECADORA ELECTRICA DE 27 PULG. (69CM)

Table ofContents / |ndice

DRYER SAFETY ........................................................... 1

INSTALLATION INSTRUCTIONS ............................... 2

Tools and Parts ....................................................... 2

Location Requirements ........................................... 2

Electrical Requirements ............................................ 3

Electrical Connection ................................................ 4

Venting Requirements .............................................. 8

Plan Vent System ...................................................... 8

Install Vent System ................................................. 10

Install Leveling Legs ............................................... 10

Level Dryer .............................................................. t t

Connect Vent .......................................................... 11

Complete Installation .............................................. 11

SERVICE NUMBERS ............................. BACK COVER

SEGURIDAD DE LA SECADORA ............................ 12

INSTRUCCIONES DE INSTALACION ..................... 12

Herramientas y piezas ........................................... 12

Requisitos de Iocalizaci&n .................................... 12

Requisitos et_ctricos ............................................. 13

Conexi6n el_ctrica ................................................. 15

Requisitos de ventilaci6n ....................................... 19

Planificaci6n del sistema de ventilaci6n ............... 20

Instalaci6n del sistema de ventilaci6n ................... 22

Instalaci6n de las patas niveladoras ..................... 22

Nivelaci6n de la secadora ..................................... 23

Conexi6n del ducto de escape ............................. 23

Complete la instalaci6n ......................................... 23

NUMEROS DE SERVICIO ........... CONTRAPORTADA

DRYER SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.

This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately follow instructions,

You can be killed or seriously injured if you don't follow

instructions,

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

3979976

INSTALLATION INSTRUCTIONS

Check that you have everything necessary for correct installation.

Proper installation is your responsibility.

• Flat-blade screwdriver • Tin snips(new vent

• Adjustable wrench that installations) opens to 1 in. (2.5 cm) or • Safety glasses

hex-head socket wrench (for adjusting dryer feet) • Caulking gun and

• Level new exhaust vent)

• #2 Phillips screwdriver • Gloves

• Vent clamps • Wire stripper (direct wire

Parts supplied:

Remove parts package from dryer drum. Check that all parts

were included.

4 leveling legs

compound (for installing

installations)

• A grounded electrical outlet located within 2 ft (61 cm) of either side of the dryer. See "Electrical Requirements."

• A sturdy floor to support the total weight (dryer and load) of 200 Ib (98.7 kg). The combined weight of a companion

appliance should also be considered. A level floor with a maximum slope of 1 in. (2.5 cm) under

entire dryer. (If slope is greater than 1 in. [2.5 cm], install

Extended Dryer Feet Kit, Part No. 279818.) Clothes may not tumble properly and models with automatic sensor cycles may not operate correctly if dryer is not level.

Do not operate your dryer at temperatures below 45°F (7°C). At lower temperatures, the dryer might not shut off at the end of an

automatic cycle. Drying times can be extended.

Install the dryer where it is protected from water and/or weather.

Check code requirements. Some codes limit, or do not permit,

installation of the dryer in garages, closets, mobile homes, or

sleeping quar[ers. Contact your local building inspector.

Installation Clearances

The location must be large enough to allow the dryer door to open fully.

Dryer Dimensions

Parts needed:

Check local codes. Check existing electrical supply and venting and see "Electrical Requirements" and "Venting Requirements"

before purchasing parts. Mobile home installations require metal exhaust system hardware

available for purchase from your local Sears store or Sears Service Center. For further information, call 1-8OO-4-MY-HOME _

(1-800-469-4663).

Explosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from dryer. Place dryer at least 18 inches (46 cm) above the floor

for a garage installation. Failure to do so can result in death, explosion, or fire.

You will need

• A location that allows for proper exhaust installation. See "Venting Requirements."

• A separate 30 amp circuit.

* Most installations require a minimum 5V2in. (14 cm) clearance

behind the dryer for the exhaust vent with elbow. See "Venting Requirements."

Minimum installation spacing for recessed area or closet

installation

The dimensions shown following are for the minimum spacing allowed.

• Additional spacing should be considered for ease of installation and servicing.

Additional clearances might be required for wall, door and floor moldings.

Additional spacing of 1 in. (2.5 cm) on all sides of the dryer is recommended to reduce noise transfer.

For closet installation, with a door, minimum ventilation

openings in the top and bottom of the door are required.

Louvered doors with equivalent ventilation openings are

acceptable.

• Companion appliance spacing should also be considered.

'_'3"

olo [_ ,m)

t,, -_1

I_ _" -_1I*-t" -_1t"I_ 2,,¢_t,,_'1<-

(z.S_)

Mobile Home-Additional Installation Requirements

This dryer is suitable for mobile home installations. The installation must conform to the Manufactured Home

Construction and Safety Standard, Title 24 CFR, Part 3280 (formerly the Federal Standard for Mobile Home Construction

and Safety, Title 24, HUD Part 280).

Mobile home installations require:

• Metal exhaust system hardware which is available for

(eu=.) (zs=.) (_cm) (74.30_}(14=_)

1. Recessed area

2, Side view - closet or confined area

3. Closet door with vents

purchase from your dealer.

Special provisions must be made in mobile homes to

introduce outside air into the dryer. The opening (such as a nearby window) should be at least twice as large as the dryer

exhaust opening.

24. z

r_3" [7.s=n)

2 3

It is your responsibility

• To contact a qualified electrical installer.

• To be sure that the electrical connection is adequate and in conformance with the National Electrical Code, ANSI/NFPA

70-latest edition and all local codes and ordinances. A copy of the above code standards can be obtained from:

National Fire Protection Association, Batterymarch Park,

Quincy, MA 02269.

• To supply the required 3 or 4 wire, single phase, 120/240-volt, 60-Hz., AC-only electrical supply (or 3 or 4 wire, 120/208-volt electrical supply, if specified on the serial/rating plate) on a

separate 30-amp circuit, fused on both sides of the line. A time-delay fuse or circuit breaker is recommended. Connect to an individual branch circuit. Do not have a fuse in the

neutral or grounding circuit.

• Do not use an extension cord.

• If codes permit and a separate ground wire is used, it is recommended that a qualified electrician determine that the ground path is adequate.

Electrical Connection

To properly install your dryer, you must determine the type of electrical connection you will be using and follow the instructions

provided for it here.

• If local codes do not permit the connection of a cabinet ground connector to the neutral wire, see "Optional 3-wire

connection" section.

• This dryer is manufactured with a 3-wire, cabinet-ground conductor connected to the NEUTRAL (white or center wire)

of the wiring harness at the terminal block.

• Use a 4-wire conductor cord when the dryer is installed in a mobile home or an area where local codes do not permit grounding through the neutral.

If using a power supply cord:

Use a UL approved power supply cord kit marked for use with

clothes dryers. The kit should contain:

• A UL approved 30 amp power supply cord, rated 120/240 volt minimum. The cord should be type SRD or SRDT and be at

least 4 ft (1.22 m) long. The wires that connect to the dryer must

end in ring terminals or spade terminals with upturned ends.

• A UL approved strain relief.

If your outlet looks like this:

4-wire receptacle (14-30R)

Then choose a 4-wire power supply cord with ring or spade terminals and UL approved strain relief. The 4-wire power supply cord, at least 4 ft (1.22 m) long, must have 4, 10 gauge solid copper wires and match a 4-wire receptacle of NEMA Type

14-30R. The ground wire (ground conductor) may be either green

or bare. The neutral conductor must be identified by a white cover.

If your outlet looks like this:

3-wire receptacle (10-30R)

Then choose a 3-wire power supply cord with ring or spade terminals and UL approved strain relief. The 3-wire power supply cord, at least 4 ft (1.22 m) long, must have 3, No.-10 copper wires and match a 3-wire receptacle of NEMA Type 10-30R.

If connecting by direct wire:

Power supply cable must match power supply (4-wire or 3-wire)

and be:

• Flexible armored cable or non-metallic sheathed copper cable (with ground wire), protected with flexible metallic

conduit. All current-carrying wires must be insulated.

• 10 gauge solid copper wire (do not use aluminum).

• At least 5 ft (1.52 m) long.

GROUNDING INSTRUCTIONS

• For a grounded, cord-connected dryer: This dryer must be grounded. In the event of malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current. This dryer uses a cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and ground-

ed in accordance with all local codes and ordinances.

• For a permanently connected dryer: This dryer must be connected to a grounded metal, permanent wtring system, or an equipment-grounding conductor must be run with the circuit conductors and connected to the equip- ment-grounding terminal or lead on the dryer.

WARNING: Improper connection of the equipment-

grounding conductor can result in a risk of electric shock.

;heck with a qualified electrician or service representative or )ersonnel if you are in doubt as to whether the dryer is proper-

grounded. Do not modify the plug on the power supply cord:

if it will not fit the outlet, have a proper outlet installed by a qualified electrician.

SAVE THESE INSTRUCTIONS

PowerSupplyCord DirectWire

FireHazard

Useanew UL approved 30 amp power supply cord.

Use a UL approved strain relief. Disconnect power before making electrical connections. Connect neutral wire (white or center wire) to center

terminal (silver). Ground wire (green or bare wire) must be connected to

green ground connector. Connect remaining 2 supply wires to remaining

2 terminals (gold). Securely tighten all electrical connections.

Failure to do so can result in death, fire, or electrical shock.

1. Disconnect power.

2. Remove the hold-down screw and terminal block cover.

1 2 3 4

Fire Hazard

Use 10 gauge solid copper wire. Use a UL approved strain relief.

Disconnect power before making electrical connections. Connect neutral wire (white or center wire) to center

terminal (silver). Ground wire (green or bare wire) must be connected to

green ground connector. Connect remaining 2 supply wires to remaining

2 terminals (gold). Securely tighten all electrical connections. Failure to do so can result in death, fire, or

electrical shock.

Assemble a s/4in. (1,9 cm) UL approved strain relief (UL marking on strain relief) into the hole below the terminal block

opening. Tighten strain relief screws just enough to hold the two clamp sections together. Put power supply cord through the strain relief, The strain relief should have a tight fit with the

dryer cabinet and be in a horizontal position.

5 6

Now complete installation following instructions for your type

of electrical connection: 4-wire (recommended)

1. Terminal block cover

2. External ground connector 3, Center, silver-colored terminal block screw

4. Hold-down screw

5. Neutral grounding wire (green/yellow)

6. Hole below terminal block opening

3-wire (if 4-wire is not available)

Electrical Connection Options 1.

If your home has: And you will be Go to Section:

connecting to:

Remove center terminal block screw. Remove appliance ground wire (green with yellow stripes)

from external ground connector screw. Fasten it under center, silver-colored terminal block screw.

4-wire receptacle A UL listed, 4-wire connection:

(NEMA type 14-30R) 120/240 volt Power Supply

amp., dryer

(_ minimum, 30 Cord

power supply

cord*

4-wire direct A fused 4-wire connection:

disconnect or Direct Wire circuit breaker

box*

3-wire receptacle A UL listed, 3-wire connection:

(NEMA type 10-30R) 120/240 volt Power Supply

amp., dryer

power supply

minimum, 30 Cord

cord*

3-wire direct A fused 3-wire connection:

disconnect or Direct Wire circuit breaker

box*

* If local codes do not permit the connection of a frame-

grounding conductor to the neutral wire, go to "Optional 3-wire connection" section.

1. External ground connector - Dotted line shows position of NEUTRAL ground wire before being moved to center

terminal block screw

2, Center silver-colored terminal block screw

3. Green/yellow wire of harness

3. Connect ground wire (green or bare) of power supply cord to

external ground conductor screw. Tighten screw.

4. Connect neutral wire (white or center wire) of power supply cord under center screw of the terminal block.

2 \\11 .................5

4-wire connection: Power supply cord

IMPORTANT: A 4-wire connection is required for mobile homes

and where local codes do not permit the use of 3-wire connections.

2 6

4 5 7

1, 4-wire receptacle (NEMA type 14-30R)

2. 4-prong plug

3. Ground prong

4. Neutral prong

5. Spade terminals with upturned ends

6. ¾ in. (1.9 cm) UL approved strain relief

7. Ring terminals

,,,,, 6

1. External ground connector

2. Green wire of power supply cord or bare copper wire

3. ¾ in (1.9 cm) UL-listed strain relief

4. Center silver-colored terminal block screw 5, Neutral wire (white or center wire)

6. Neutral grounding wire (green/yellow)

5. Connect the other wires to outer terminal block screws. Tighten screws.

6. Tighten strain relief screws.

7. Insert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold-down screw.

4-wire connection: Direct Wire

IMPORTANT: A 4-wire connection is required for mobile homes

and where local codes do not permit the use of 3 wire connections.

Direct wire cable must have 5 ft (1.52 m) of extra length so dryer

can be moved if needed. Strip 5 in. (12.7 cm) of outer covering from end of cable, leaving

bare ground wire at 5 in. (12.7 cm). Cut 11/2in. (3.8 cm) from 3

remaining wires. Strip insulation back 1 in. (2.5 cm). Shape ends of wires into a hook shape.

3. Connect ground wire (green or bare) of power supply cable to external ground conductor screw. Tighten screw.

4. Placethehookedendoftheneutralwire(whiteorcenterwire) of power supply cable under the center screw of terminal

block (hook facing right). Squeeze hooked end together.

Tighten screw.

..................... 4

....................

When connecting to the terminal block, place the hooked end of the wire under the screw of the terminal block (hook facing right),

squeeze hooked end together and tighten screw.

1. Remove center terminal block screw.

2. Remove appliance ground wire (green with yellow stripes) from external ground connector screw. Fasten it under center,

silver-colored terminal block screw.

1.External ground connector - Dotted line shows position of NEUTRAL ground wire before being moved to center

terminal block screw

2. Center silver-colored terminal block screw

3. Green/yellow wire of harness

1, External ground connector

2. Green wire of power supply cord or bare copper wire

3. ¾in, (1.9 cm) UL-tisted strain relief

4. Center silver-colored terminal block screw

5. Neutral wire (white or center wire)

6. Neutral grounding wire (green/yellow)

Place the hooked ends of the other power supply cable wires under the outer terminal block screws (hooks facing right).

Squeeze hooked ends together. Tighten screws.

!! !!

6. Tighten strain relief screws.

7. Insert tab of terminal block cover into slot of dryer rear paneL Secure cover with hold-down screw.

3-wire connection: Power supply cord

Use where local codes permit connecting cabinet-ground conductor to neutral wire.

2 4 5

1.3-wire receptacle (NEMA type 10-30R)

2. 3-wire plug

3. Neutral prong

4. Spade terminals with upturned ends 5, ¾ in (1.9 cm) UL approved strain relief

6. Ring terminals

7. Neutral wire (white or center wire)

1. Loosen or remove center terminal block screw.

2. Connect neutral wire (white or center wire) of power supply cord to the center, silver-colored terminal screw of the

terminal block. Tighten screw.

Loosen or remove center terminal block screw.

Place the hooked end of the neutral wire (white or center wire)

of power supply cable under the center screw of terminal

block (hook facing right). Squeeze hooked end together.

Tighten screw.

1, External ground connector

2. Neutral grounding wire (green/yellow)

3. Center silver-colored terminal block screw

4. Neutral wire (white or center wire)

5. ¾in. (1.9 crn) UL-listed strain relief

3. Connect the other wires to outer terminal block screws.

Tighten screws.

4. Tighten strain relief screws.

5. Insert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold-down screw.

3-wire connection: Direct Wire

Use where local codes permit connecting cabinet-ground conductor to neutral wire.

Direct wire cable must have 5 ft (1.52 m) of extra length so dryer

can be moved if needed. Strip 3V2in. (8.9 cm) of outer covering from end of cable. Strip

insulation back 1 in. (2.5 cm). If using 3-wire cable with ground

wire, cut bare wire even with outer covering. Shape ends of wires

into a hook shape.

1, External ground connector

2. Neutral grounding wire (green/yellow)

3. Center silver-colored terminal block screw

4. Neutral wire (white or center wire)

5. _ in. (1.9 cm) UL-listed strain relief

Place the hooked ends of the other power supply cable wires under the outer terminal block screws (hooks facing right).

Squeeze hooked ends together. Tighten screws.

!! !!

4. Tighten strain relief screws.

5. Insert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold-down screw.

Optional 3-wire connection

When connecting to the terminal block, place the hooked end of the wire under the screw of the terminal block (hook facing right),

squeeze hooked end together and tighten screw. See following example.

Use for direct wire or power supply cord where local codes do not permit connecting cabinet-ground conductor to

neutral wire.

1. Remove center terminal block screw.

2. Remove appliance ground wire (green with yellow stripes) from external ground connector screw. Connect appliance

ground wire and the neutral wire (white or center wire) of

power supply cord/cable under center, silver-colored terminal block screw. Tighten screw.

3. Connect the other wires to outer terminal block screws. Tighten screws.

!! !!

4. Tighten strain relief screws.

5. Insert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold-down screw.

6. Connect a separate copper ground wire from the external ground connector screw to an adequate ground.

1, External ground connector

2. Neutral grounding wire (green/yellow)

3. Neutral wire (white or center wire)

4. Grounding path determined by a qualified electrician

• The dryer exhaust must not be connected into any gas vent, chimney, wall, ceiling, or a concealed space of a building.

• Do not use an exhaust hood with a magnetic latch.

• Do not install flexible metal vent in enclosed walls, ceilings or floors.

Use clamps to seal all joints. Exhaust vent must not be

connected or secured with screws or other fastening devices which extend into the interior of the duct. Do not use duct

tape.

IMPORTANT: Observe all governing codes and ordinances.

Improper venting can cause moisture and lint to collect

indoors, which may result in:

• Moisture damage to woodwork, furniture, paint, wall- paper, carpets, etc.

• Housecleaning problems and health problems.

Use a heavy metal vent. Do not use plastic or metal foil vent. Rigid metal vent is recommended to prevent crushing and kinking.

Flexible metal vent must be fully extended and supported when

the dryer is in its final position. Remove excess flexible metal vent to avoid sagging and kinking that may result in reduced airflow

and poor performance. An exhaust hood should cap the vent to prevent rodents and

insects from entering the home. Exhaust hood must be at least 12 in. (30.5 cm) from the ground or

any object that may be in the path of the exhaust (such as flowers, rocks or bushes, etc.).

If using an existing vent system, clean lint from the entire length

of the system and make sure exhaust hood is not plugged with

lint. Replace any plastic or metal foil vent with rigid metal or

flexible metal vent.

Fire Hazard

Use a heavy metal vent. Do not use a plastic vent.

Do not use a metal foil vent. Failure to follow these instructions can result in death

or fire.

WARNING: To reduce the risk of fire, this dryer MUST BE

EXHAUSTED OUTDOORS.

4 in. (10.2 cm) heavy metal exhaust vent and clamps must be

used. DURASAFE TM venting products are recommended. DURASAFF Mvent products can be purchased from your local

Sears store or Sears Service Center. For more information, call

1-800-4-MY-HOME ®(1-800-469-4663).

Typical exhaust installations

Typical installations vent the dryer from the rear of the dryer. Other installations are possible.

J!:

'........... rlTil]2;

1, Dryer

2. Elbow

3. Watt

4. Exhaust hood

5. Clamps

6. Rigid metal or flexible metal vent

7. Vent length necessary to connect elbows

8. Exhaust outlet

+ 16 hidden pages