Kenmore 11020232710, 11020232711, 11020372710, 11020372711, 11026132410 Installation Guide

...

Installation Instructions Instrucciones de instalaci6n

Instructions pour I'installation

English / Espa_ol / Fran(;ais

I(enmore

TOpoL d W

IIIIll,,,,,,,,,_v_d@_de Ca a $uper[@_

IIIIIJ,,,,,,,,,aveus÷@C ÷÷ 't Superior

Table of Contents

WASHER SAFETY ...................................................................... 2

INSTALLATION REQUIREMENTS ............................................... 2

Tools and Parts .................................................................. 2

Location Requirements ...................................................... 3

Drain System ..................................................................... 3

Electrical Requirements ...................................................... 4

Indice

SEGURIDAD DE LA LAVADORA ................................................. 9

REQUlSITOS DE INSTALACION .................................................. 9

Herramlentas y plezas ........................................................ 9

Requisitos de ubicaci6n .................................................... 10

Sistema de desagiJe .......................................................... 11

Requisitos el_ctricos .......................................................... 11

Table des mati_res

SIECURITIEDE LA LAVEUSE....................................................... 17

EXIGENCES D'INSTALLATION .................................................. 17

Outillage et pi_ces .............................................................. 17

Exigences d'emplacement .................................................. 18

Syst_me de vldange ........................................................... 19

Specifications _lectriques .................................................... 19

INSTALLATION INSTRUCTIONS ................................................ 5

Before you start: remove shipping materials .................... 5

Connect Drain Hose ........................................................... 6

Connect Inlet Hoses ........................................................... 6

Level Washer ...................................................................... 7

Complete Installation Checklist ......................................... 8

INSTRUCCIONES DE INSTALACION ......................................... 12

Antes de comenzar: quite los materiales

de transporte .................................................................... 12

Conexi6n de la manguera de desagiJe ............................. 13

Conexi6n de las mangueras de entrada ........................... 14

Nivelaci6n de la lavadora ................................................ 15

Complete la instalaci6n .................................................... 16

INSTRUCTIONS D'INSTALLATION ............................................ 20

Avant de commencer : retrait du materiel d'exp_dltion ..... 20

Raccordement du tuyau de vidange ................................... 21

Raccordement des tuyaux d'arriv_e d'eau ......................... 22

Etablissement de I'aplomb de la laveuse ........................... 23

Liste de v_rification pour I'ach_vement

de I'installation .......................................... Couverture arri_re

P/N W10682744B Sears Brands Management Corporation Hofl:man Estates, IL 60179 U.S.A.

www.kenmore.com www.sears.com

Sears Canada Inc. Toronto, Ontario, Canada M5B 2C3

www.sears.ca

WASHER SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.

This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately follow instructions.

You can be killed or seriously injured if you don't follow

instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

INSTALLATION NOTES

Date of purchase: Date of installation:

Installer:

INSTALLATION REQUIREMENTS

Tools and Parts Gather required tools and parts before starting installation.

Tools needed:

Adjustable or open end wrench 9/16" (14 mm)

4" rain

Level

Model number:

Serial number:

Optional tools:

Flashlight

Bucket

Parts supplied:

NOTE: All parts supplied for installation are in

cardboard insert in the top of the washer.

Wood block

Pliers that open to 13#, (44.5 mm)

Ruler or measuring tape

Beaded tie strap Drain hose with clamp

Parts needed: (Not supplied with washer)

Inlet hoses with flat washers

To order, please refer to toll-free phone numbers on back page of your Use and Care Guide.

• 8212656RP 10 ft. (3.0 m) Inlet hose, Black EPDM (2 pack)

• 8212641 RP 5 ft. (1.5 m) Inlet hose, Black EPDM (2 pack)

• 8212546RP 4 ft. (1.2 m) Inlet hose, Black EPDM (2 pack)

• 8212545RP 5 ft. (1.5 m) Inlet hose, Red and Blue EPDM (2 pack)

• 8212487RP 5 ft. (1.5 m) Nylon braided inlet hose (2 pack)

• 8212638RP 6 ft. (1.8 m) Nylon braided inlet hose, space saving 90° elbow, hypro-blue steel couplings (2 pack)

• 8212637RP 6 ft. (1.8 m) Inlet hose, Black EPDM, space saving 90° elbow, hypro-blue steel couplings (2 pack)

Alternate parts: (Not supplied with washer) Your installation may require additional parts. To order, please

refer to toll-free numbers on back page of your Use and Care Guide.

If you have: Overhead sewer

1" (25 mm) standpipe

Drain hose too short

Lint clogged drain

You will need:

Standard 20 gal. (76 L) 39" (990 ram) tall drain tub or utility sink, sump pump and connectors (available from local plumbing suppliers)

2" (51 mm) diameter to 1" (25 mm) diameter Standpipe Adapter

Part Number 3363920 Connector Kit Part Number 285835

Extension Drain Hose Part Number 285863 Connector Kit Part Number 285835

Drain Protector Part Number 367031 Connector Kit Part Number 285835

LOCAT(ON REQU(REMENTS

Select proper location for your washer to improve performance and minimize noise and possible "washer walk", Install your washer in a basement, laundry room, closet, or recessed area,

(648 mm)

You will need:

• A water heater set to 120 ° F (49° C).

• A grounded electrical outlet located within 4 ft (1.2 m) of power cord on back of washer.

• Hot and cold water faucets located within 3 ft (0.9 m) of hot and cold water fill valves on washer, and water pressure

of 20-100 psi (138-690 kPa).

• A level floor with maximum slope of 1" (25 mm) under entire washer. Installing on carpet is not recommended.

• Floor must support washer's total weight (with water and load) of 315 Ibs (143 kgs).

IMPORTANT: Do not install, store, or operate washer where it will be exposed to weather or in temperatures below 32° F (0° C). Water remaining in washer after use may cause damage in tow temperatures. See "Washer Care" in your Use and Care Guide for winterizing information.

Proper installation is your responsibility.

Recessed area or closet installation

3 II

(76ram)

_1 _-_

max,

(356 mm)

19"

, ,_i ;;,_I I

' N', i',i_l II

,, I ii

...2 .i II

mmj .: I II

(25 mm)

Dimensions show recommended spacing allowed, except for closet door ventilation openings which are minimum required. This washer has been tested for installation with spacing of 0" (0 mm) clearance on the sides. Consider allowing more space for ease of installation and servicing, and spacing for companion appliances and clearances for walls, doors, and floor moldings. Add spacing of 1" (25 mm) on all sides of washer to reduce noise transfer. If a closet door or louvered door is installed, top and bottom air openings in door are required.

24 in. 2

1155cm2}

176mm)

43 'l

(1092 mm)

DRAmN SYSTEM

Drain system can be installed using a floor drain, wall standpipe, floor standpipe, or laundry tub. Select method you need.

Floor standpipe drain system

Minimum diameter for a standpipe drain: 2" (51 mm). Minimum carry-away capacity: 17 gal. (64 L) per minute. Top of standpipe

must be at least 39" (990 mm) high; install no higher than 96" (2.44 m) from bottom of washer. If you must install higher than

96" (2.44 m), you will need a sump pump system.

Wall standpipe drain system

See requirements for floor standpipe drain system. Floor drain system

ELECTRICAL REQUIREMENTS

Electrical Shock Hazard

Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter.

Do not use an extension cord. Failure to follow these instructions can result in death,

fire, or electrical shock.

• A 120 volt, 60 Hz., AC only, 15- or 20-amp, fused electrical supply

is required. A time-delay fuse or circuit breaker is recommended. It is recommended that a separate circuit breaker serving only this appliance be provided.

• This washer is equipped with a power supply cord having

a 3 prong grounding plug.

• To minimize possible shock hazard, the cord must be plugged

into a mating, 3 prong, grounding-type outlet, grounded in accordance with local codes and ordinances. If a mating outlet

is not available, it is the personal responsibility and obligation of the customer to have the properly grounded outlet installed

by a qualified electrician.

• If codes permit and a separate ground wire is used, it is

recommended that a qualified electrician determine that the ground path is adequate.

• Do not ground to a gas pipe.

• Check with a qualified electrician if you are not sure the

washer is properly grounded.

• Do not have a fuse in the neutral or ground circuit.

Floor drain system requires a Siphon Break Kit (Part Number

285834), 2 Connector Kits (Part Number 285835), and an Extension Drain Hose (Part Number 285863) that may be

purchased separately. To order, please see toll-free phone numbers in your Use and Care Guide. Minimum siphon break: 28" (710 mm) from bottom of washer. (Additional hoses may

be needed.)

Laundry tub drain system

Minimum capacity: 20 gal. (76 L). Top of laundry tub must be at least 39" (990 ram) above floor; install no higher than 96" (2.44 m)

from bottom of washer.

IMPORTANT: To avoid siphoning, no more than 4.5" (114 mm) of drain hose should be inside standpipe or below the top of wash tub. Secure drain hose with beaded tie strap.

GROUNDING INSTRUCTIONS

For a grounded, cord-connected washer:

This washer must be grounded. In the event of a malfunction or breakdown, grounding will reduce the risk of electrical shock by providing a path of least resistance for electric current. This washer is equipped with a cord having an

equipment-grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local

codes and ordinances. WARNING: Improper connection of the equipment-

grounding conductor can result in a risk of electric shock. Check with a qualified electrician or serviceman if you are

in doubt as to whether the appliance is properly grounded. Do not modify the plug provided with the appliance - if it will

not fit the outlet, have a proper outlet installed by a qualified

electrician.

For a permanently connected washer:

This washer must be connected to a grounded metal, permanent wiring system, or an equipment grounding

conductor must be run with the circuit conductors and connected to the equipment-grounding terminal or lead

on the appliance.

INSTALLATmON INSTRUCTIONS

Excessive Weight Hazard

Use two or more people to move and install washer. Failure to do so can result in back or other injury,

Before you start: remove shipping materials It is necessary to remove all shipping materials for proper

operation and to avoid excessive noise from washer.

Remove packing tray from tub

• Move washer

(1.2

Move washer to within 48" (1.2 m) of its final location; it must be in a fully upright position.

NOTE: To avoid floor damage, set washer onto cardboard before moving it and make sure lid is taped shut.

_), Remove shipping base

Remove tape from washer lid, open lid and remove cardboard packing tray from tub. Be sure to remove all parts from tray.

NOTE: Keep tray in case you need to move washer later.

f4, Free power cord

Firmly grasp power cord plug and pull to free from rear panel. Gently place power cord over console to allow free access

to back of washer.

To avoid damaging floor, place cardboard supports from shipping carton on floor behind washer. Tip washer back and place on cardboard supports. Remove shipping base by rotating base 90 ° to the right. Set washer upright.

IMPORTANT: Removing shipping base is necessary for proper operation. If your washer includes a sound shield, please refer

to the instructions included with the sound shield to install it at this time.

CONNECT DRA N HOSE

If clamp is not already in place on elbow end of drain hose, slide it over end as shown. Squeeze clamp with pliers and slide black elbow end of drain hose onto black drain port and secure with clamp.

For a laundry tub or standpipe drain, go to step 6. For a floor drain, remove the preinstalled drain hose form as

shown in Step 7. You may need additional parts with separate directions. See "Tools and Parts".

(floor drain installations only)

For floor drain installations, you will need to remove the drain hose form from the end of the drain hose. You may need additional parts with separate directions. See "Tools and Parts".

CONNECT INLET HOSES

Washer must be connected to water faucets with new inlet hoses with flat washers (not provided). Do not use old hoses.

NOTE: Both hoses must be attached and have water flowing to inlet valves. If you are only connecting to a cold water

faucet, you must use a Y-adapter (not provided).

_6. Place drain hose in standpipe

Drain

Place hose into standpipe (shown in picture) or over side of laundry tub.

IMPORTANT: 4.5" (114 mm) of drain hose should be inside standpipe; do not force excess hose into standpipe or lay on bottom of laundry tub. Drain hose form must be used.

_8. Connect inlet hoses to water faucets

Verify location of hot and cold faucets. Attach hose to hot water faucet. Screw on coupling by hand until it is seated on washer. Use pliers to tighten couplings an additional two- thirds turn. Repeat this step with second hose for cold water

faucet. IMPORTANT: Do not overtighten or use tape or sealants on

valve when attaching to faucets or washer. Damage can result. HELPFUL TIP: Make note of which hose is connected to hot

water to help in attaching hoses to washer correctly. In most standard configurations, hoses will cross over each other when attached correctly.

Clear water lines

12. Secure drain hose

Standpipe Wall

Run water for a few seconds through hoses into a laundry tub, drainpipe, or bucket to prevent clogs. Water should run until clear.

O. Connect inlet hoses to washer

Attach hot water hose to hot water inlet valve marked with a red ring. Screw coupling by hand until it is snug. Use pliers to

tighten couplings an additional two-thirds turn. Repeat with cold water inlet valve.

IMPORTANT: To reduce risk of hose failure, replace the hoses every 5 years. Record hose installation or replacement dates

for future reference.

• Periodically inspect and replace hoses if bulges, kinks, cuts, wear, or leaks are found.

1. Check for leaks

Secure drain hose to laundry tub leg, drain standpipe, or inlet hoses for wall standpipe with beaded tie strap.

LEVEL WASHER

IMPORTANT: Level washer properly to reduce excess noise and vibration.

Place level here

Move the washer to its final location. Place a level on top edges of washer. Use side seam as a guide to check levelness of sides. Check levelness of front using lid, as shown. Rock

washer back and forth to make sure all four feet make solid contact with floor. If washer is level, skip to step 15, (on

models with metal feet) or step 16 (on models with plastic feet).

Turn on water faucets to check for leaks. A small amount of water may enter washer. It will drain later.

Not Level LEVEL Not Level

4. Adjust leveling feet

Jam nut

Models with

metal feet

Electrical Shock Hazard

Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter.

Do not use an extension cord. Failure to follow these instructions can result in death,

fire, or electrical shock.

Models with

plastic feet

If washer is not level:

On models with metal feet, use a 9/16" or 14 mm open-end or adjustable wrench to turn jam nuts clockwise on feet until they are about 1/2" (13 mm) from the washer cabinet. Then turn the leveling foot clockwise to lower the washer or counterclockwise

to raise the washer. On models with plastic feet, use adjustable pliers to turn the

plastic leveling foot counterclockwise to lower the washer or clockwise to raise the washer. On all models, recheck levelness

of washer and repeat as needed. HELPFUL TIP: You may want to prop up front of washer

about 4" (102 mm) with a wood block or similar object that will support weight of washer.

_15. Tighten leveling feet

On models with metal feet, when washer is level, use a 9/16" or 14 mm open-end or adjustable wrench to turn jam

nuts counterclockwise on leveling feet tightly against washer cabinet.

HELPFUL TIP: You may want to prop washer with wooden block.

COMPLETE

INSTALLATmON

CNEC[(L[ST

Check electrical requirements. Be sure you have correct electrical supply and recommended grounding method.

Check that all parts are now installed. If there is an extra part, go back through steps to see what was skipped.

Check that you have all of your tools. Check that any shipping materials were completely

removed from washer. Check that water faucets are on. Check for leaks around faucets and inlet hoses.

Remove protective film from console and any tape remaining on washer.

Check that washer is plugged into a grounded 3 prong outlet.

Dispose of/recycle all packaging materials. Read "Washer Care" in your Use and Care Guide.

To test and clean your washer, measure 1/2 of normal recommended amount of powdered or liquid detergent

and pour it into washer basket or detergent dispenser (on some models). Close lid. Select any cycle. Start washer

and allow to complete full cycle.

+ 16 hidden pages