Kenmore 11027022710, 11027022711 Installation Guide

Installation Instructions Instrucciones de instalación

English / Español

Table of Contents / Índice......2

Kenmore®

Commercial Washer Lavadora comercial

P/N W10837709A

Sears Brands Management Corporation Hoffman Estates, IL 60179 U.S.A.

www.kenmore.com

Table of Contents

Índice

WASHER SAFETY .................................................................................. 3

TOOLS & PARTS .................................................................................... 4

DIMENSIONS ......................................................................................... 5

LOCATION REQUIREMENTS ............................................................... 6

DRAIN SYSTEM ...................................................................................... 7

ELECTRICAL REQUIREMENTS ............................................................. 8

INSTALLATION INSTRUCTIONS ......................................................... 9

CONNECT DRAIN HOSE ....................................................................10

CONNECT INLET HOSES .....................................................................11

LEVEL WASHER ....................................................................................12

INSTALLING COIN SLIDE AND COIN BOX ....................................12

COMPLETE INSTALLATION ................................................................13

TYPICAL FULL LOAD SIZES .................................................................13

WASHER MAINTENANCE ..................................................................14

ALTERNATE PARTS & ACCESSORIES ................................................14

WARRANTY ........................................................................................... 15

ASSISTANCE OR SERVICE ............................................. BACK COVER

SEGURIDAD DE LA LAVADORA ......................................................... 16

HERRAMIENTAS Y PIEZAS .................................................................. 17

DIMENSIONES ..................................................................................... 18

REQUISITOS DE UBICACIÓN ............................................................ 19

SISTEMA DE DESAGÜE ...................................................................... 20

REQUISITOS ELÉCTRICOS ................................................................... 21

INSTRUCCIONES DE INSTALACIÓN ................................................ 22

CONEXIÓN DE LA MANGUERA DE DESAGÜE ..............................23

CONEXIÓN DE LAS MANGUERAS DE ENTRADA ......................... 24

NIVELACIÓN DE LA LAVADORA ....................................................... 25

INSTALACIÓN DEL TRAGAMONEDAS

Y LA CAJA DE MONEDAS ................................................................. 25

COMPLETE LA INSTALACIÓN ......................................................... 26

TAMAÑOS DE CARGAS TÍPICAS DE VOLUMEN COMPLETO ..... 26

MANTENIMIENTO DE LA LAVADORA ............................................ 27

PIEZAS Y ACCESORIOS ALTERNATIVOS ........................................ 27

GARANTÍA ............................................................................................ 28

AYUDA O SERVICIO TÉCNICO ............................CONTRAPORTADA

WASHER SAFETY

TOOLS & PARTS

Tools Needed:

Level Pliers Utility Knife

9/16" (14 mm)

Open-End Wrench

Optional tools:

Flashlight Bucket

Parts Supplied:

Flat-Blade Screwdriver

Water Inlet Hoses (2) Inlet Hose Washers (4)

Service Door Lock

Assembly

Coin Slide Decal Kit

Drain hose with clamp,

U-form, and cable tie

DIMENSIONS

27"

Front View Side View

(686 mm)

/4"

(210 mm)

421/2"

(1.080 m)

361/4"

(921 mm)

(25 mm)

Back View

16"

(406 mm)

101/2"

(267 mm)

51/2"

(140 mm)

441/2"

(1.130 m)

371/4"

(946 mm)

421/2"

(1.080 m)

363/4"

(933 mm)

63/4"

(171 mm)

(25 mm)

41/4"

(108 mm)

27"

(686 mm)

LOCATION REQUIREMENTS

Selecting the proper location for your washer improves performance and minimizes noise and possible washer “walk.”

Your washer can be installed in a basement, laundry room, or recessed area. See “Drain System.”

Companion appliance location requirements should also be considered.

IMPORTANT: Do not install or store the washer where it will be exposed to the weather. Do not store or operate the washer in temperatures at or below 32°F (0°C). Some water can remain in the washer and can cause damage in low temperatures. Proper installation is your responsibility.

You will need:

■ A water heater set to 120°F (49°C).

■ A grounded electrical outlet located within 4 ft. (1.2 m) of

power cord on back of washer. See “Electrical Requirements.”

■ Hot and cold water faucets located within 4 ft. (1.2 m)

of hot and cold water ll valves on washer, and water pressure of 20–100 psi (138–690 kPa). A pressure reduction valve should be used in the supply line where inlet pressure entering the building exceeds 100 PSI (690 kPa) to avoid damage to the washer mixing valve.

■ Single washer installations require 12" (300 mm) minimum

risers to provide an air cushion and avoid noise and damage to valves.

■ A level oor with maximum slope of 1" (25 mm) under entire

washer. Installing on carpet is not recommended.

■ Floor must support washer’s total weight (with water and load)

of 315 lbs (143 kgs).

■ A oor drain under the bulkhead. Prefabricated bulkheads

with electrical outlets, water inlet lines, and drain facilities should be used only where local codes permit.

Recessed Area or Closet Installation

This washer may be installed in a recessed area. The installation dimensions shown are the minimum spaces allowable. Additional spacing should be considered for ease of installation and servicing. Companion appliance spacing should be considered.

Minimum installation spacing

16"

(406 mm)

DRAIN SYSTEM

(203 mm)

Drain system can be installed using a oor drain, wall standpipe, oor standpipe, or laundry tub. Select method you need.

Floor standpipe drain system

39"

(203 mm)

Minimum diameter for a standpipe drain: 2" (51 mm). Minimum carry-away capacity: 10 gal. (38 L) per minute. Top of standpipe must be at least 39" (990 mm) high; install no higher than 96" (2.44 m) from bottom of washer.

(990 mm)

Wall standpipe drain system

(203 mm)

Floor drain system

Floor drain system requires a Siphon Break Kit (Part Number

285320). Minimum siphon break: 28" (710 mm) from bottom of washer. Additional hoses may be needed.

Laundry tub drain system

39"

(990 mm)

Minimum capacity: 20 gal. (76 L). The top of the laundry tub must be at least 39" (990 mm) above oor.

See requirements for oor standpipe drain system.

ELECTRICAL REQUIREMENTS

■ A 120-volt, 60-Hz., AC-only, 15- or 20-amp, fused electrical

supply is required. A time-delay fuse or circuit breaker is recommended. It is recommended that a separate circuit breaker serving only this appliance be provided.

■ This washer is equipped with a power supply cord having

a 3 prong grounding plug.

■ To minimize possible shock hazard, the cord must be plugged

into a mating, 3 prong, grounding-type outlet, grounded in accordance with local codes and ordinances. If a mating outlet is not available, it is the personal responsibility and obligation of the customer to have the properly grounded outlet installed

by a qualied electrician.

■ If codes permit and a separate ground wire is used, it is

recommended that a qualied electrician determine that

the ground path is adequate.

■ Do not ground to a gas pipe.

■ Check with a qualied electrician if you are not sure the

washer is properly grounded.

■ Do not have a fuse in the neutral or ground circuit.

INSTALLATION INSTRUCTIONS

It is necessary to remove all shipping materials for proper operation and to avoid excessive noise from washer.

1. Move washer to within 4 ft (1.2 m) of its nal location; it must

be in a fully upright position.

NOTE: To avoid oor damage, set washer onto cardboard

before moving it and make sure lid is taped shut.

3. Remove tape from washer lid, open lid, and remove cardboard

packing tray from tub. Be sure to remove all parts from tray.

NOTE: Keep tray in case you need to move washer later.

2. To avoid damaging oor, place cardboard supports from

shipping carton on oor behind washer. Tip washer back

and place on cardboard supports. Remove shipping base. Set washer upright.

IMPORTANT: Removing shipping base is necessary for proper

operation.

NOTE: Keep shipping base in case you need to move washer

later.

CONNECT DRAIN HOSE

Proper routing of the drain hose avoids damage to your oor due to water leakage.

Remove drain hose from the washer drum

1. Remove cap from the washer drain port on the back of

the washer.

2. If clamp is not already in place on elbow end of drain hose, slide it over end as shown.

5. Place hose into standpipe (shown in picture) or over side

of laundry tub.

IMPORTANT:

■ Drain hose is not to exceed 8" (203 mm) into drain pipe;

do not force excess hose into standpipe or lay on bottom of laundry tub. Drain hose form must be used.

■ It is the responsibility of the installer to install and secure

the drain hose into the provided plumbing/drain in a manner that will avoid the drain hose coming out of, or leaking from, the plumbing/drain.

Drain

hose form

(203 mm)

6. For oor drain installations, you will need to remove the drain

hose form from the end of the drain hose. You may need additional parts with separate directions. See “Tools and Parts.”

3. Squeeze clamp with pliers and slide elbow end of drain hose onto washer drain port and secure with clamp.

4. The washer drain system can be installed using a oor drain, wall standpipe, oor standpipe, or laundry tub.

7. The oor drain system requires a siphon break that may be

purchased separately. The siphon break (Part Number 285320) must be a minimum of 28" (710 mm) from the bottom of the washer. Additional hoses might be needed.

+ 22 hidden pages