Kenmore 11026152500 Installation Guide

JNSTALLA ON JN_

COMMERCIAL WASHER

®

Write down the model and serial numbers before installing washer,
Both numbers are listed on the modeVseriat rating plate located

under the lid,
Model #

Serial #
Date of Purchase

8575077

www_sears_oom

Table of Contents

WASHER SAFETY ........................................................................ 2

iNSTALLATiON REQUIREMENTS .............................................. 3

Tools and Parts .......................................................................... 3

Location Requirements .............................................................. 3

Drain System .............................................................................. 4

Electrical Requirements ............................................................ 5

INSTALLATION INSTRUCTIONS ............................................ 6

Before You Start ........................................................................ 6

Remove Shipping Strap ............................................................ 6

Connect the Hoses .................................................................... 6

Level the VVasher ...................................................................... 7

Install Coin Slide and Coin Box.................................................. 8

Complete InstaUation ................................................................ 8

Adjust Timer Clutch .................................................................. 9

Changing Vend Price (for Coin Slide Mechanism

Provided with Washer) .............................................................. 9

Additional Features .................................................................. 10

WASHERSAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.

This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately
follow instructions.

You can be killed or seriously injured if you don't follow

instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of fire, electric shock, or injury to persons when using the washer, follow basic precautions,

including the following:

_, Read all instructions before using the washer.
_, Do not wash articles that have been previously cleaned

in, washed in, soaked in, or spotted with gasoline,
dry-cleaning solvents, other flammable, or explosive

substances as they give off vapors that could ignite or
explode.

_,Do not add gasoline, dry-cleaning solvents, or other

flammable, or explosive substances to the wash water.
These substances give off vapors that could ignite or

explode.

_,Under certain conditions, hydrogen gas may be

produced in a hot water system that has not been used
for 2 weeks or more. HYDROGEN GAS IS

EXPLOSIVE. If the hot water system has not been
used for such a period, before using the washing

machine, turn on all hot water faucets and let the water
flow from each for several minutes. This will release

any accumulated hydrogen gas. As the gas is
flammable, do not smoke or use an open flame during

this time.

SAVE THESE INSTRUCTIONS

mDo not allow children to play on or in the washer. Close

supervision of children is necessary when the washer is used
near children.

mBefore the washer is removed from service or discarded,

remove the door or lid.

mDo not reach into the washer if the drum, tub or agitator is

moving.

mDo not install or store the washer where it will be exposed to

the weather.

mDo not tamper with controls.
mDo not repair or replace any part of the washer or attempt any

servicing unless specifically recommended in this manual or in
published user-repair instructions that you understand and

have the skills to carry out.

mSee "Electrical Requirements" for grounding instructions.

INSTALLATIONREQUIREMENTS

Gather the required tools and parts before starting installation.
Read and follow the instructions provided with any tools

listed here=
Tools needed

m LeveI
m Utility knife

m Scissors
m 8" or 10" adjustable wrench

m Flat-blade screwdriver
m Pliers

m Bucket

Parts supplied
Remove parts bag from washer. Check that all parts were

included.
m 1 hose clamp

m 2 inlet hoses
m 4 flat water hose washers
m 2 front-leveling legs with nuts

m 1 drain hose

IMPORTANT: Do not install or store the washer where it will be
exposed to the weather.

Proper installation is your responsibility.
You will need:

_, A water heater set to deliver 120°F (49°C) water to the washer.
_, A grounded electrical outlet located within 4 ft (1=2m) of where

the power cord is attached to the back of the washer.
See "Electrical Requirements."

_, Hot and cold water faucets located within 4 ft (1.2 m) of the

hot and cold water fill valves, and water pressure of 10-100 psi
(69-690 kPa).

_, A Ievel floor with a maximum slope of 1" (2=5cm) under entire

washer.

_, A sturdy floor to support the washer weight (washer, water

and load) of 315 Ibs (143 kgs)=

_, A 12" (30 cm) minimum riser to provide an air cushion and

prevent noise and damage to valves for a single washer
installation.

Do not store or operate the washer in temperatures at or below
32°F (0°C). Some water can remain in the washer and can cause

damage in low temperatures.

RecessedAreaa_dCloset_staHatio__structio_s

ThiswashermaybeinstalledinarecessedareaordoseL
Theinstallationspacingisininchesandistheminimum

allowable.Additionalspacingshouldbeconsideredforeaseof
installation,servicing,andcompliancewithlocalcodesand

ordinances.
Ifclosetdoorisinstalled,theminimumunobstructedairopening

inthetopandbottomisrequired.Louvereddoorswithequivalent
airopeningsareacceptable.

MinimumInstallationC_earances

j closet door

481n 2 __

__ omo

17"

(43 cm)

,3100m2, U

4 _

(10cm)

min.

Product Dimensions

A

B

L

t"/2.6om,

rain.

Recessed front view Closet side view

48in_

(310 cm2)"

Front view

24 in_
(155 cm_)_

*Opening is the minimum for a closet door,

Louvered doors with equivalent air openings are acceptable,

[] Additional spacing should be considered for the ease of

installation and servicing.

[] Additional clearances may be required for wall, door and floor

moldings.

[] Additional spacing of 1" (2.5 cm) on all sides of the washer is

recommended to reduce noise transfer.

[] Companion spacing should also be considered.

closet

©

door

3" (7.6cm)

3" (7.6 cm)

M

A. 43" (109 crn)
B. 38_" (97cm)

C. 35" (89 crr_)
D. 1½" (4 crn)

E. 27¾" (70.5 cm)
E 25 ½" (65 cm)

G. Water inlets
H. 7" (18 cm)

I. Power supply cord
J. Water level switch and shaft

K. Label
L. Drain hose connector

M. 7" (18 cm)
N. 5" (12.7 cm)

O. 27" (68.5 cm)
P. 5 ¼" (13.3 cm)

O. 1" (2.5 cm)

Standpipe Drain System

The standpipe drain requires a minimum diameter standpipe of
2" (5 cm). The minimum carry-away capacity can be no Iess than

17 gaL (64 L) per minute.
The top of the standpipe must be at least 39" (99 cm) high and

no higher than 96" (243.8 cm) from the bottom of the washer.