Kenmore 11024904202 User Manual

WASHER INSTALLATION INSTRUCTIONS

INSTRUCCIONES PARA LA INSTALACIÓN DE

LA LAVADORA

INSTRUCTIONS POUR L’INSTALLATION DE LA LAVEUSE

Table of Contents / Indice / Table des matièies

WASHER SAFETY INSTALLATION REQUIREMENTS

Tools and Parts

Location Requirements...................................2

Drain System...................................................3

Electrical Requirements

INSTALLATION INSTRUCTIONS

Before You Start............................................ 4

Remove Shipping Strap

Connect Drain Hose...................................... 5

Connect the Inlet Hoses

Secure the Drain Hose....................................6

Level the Washer

Complete Installation.......................................7

SERVICE NUMBERS

.........

.................................. 1

...............................................

............................................

...

................

....................

................................

............... 4

..................................

BACK COVER

SEGURIDAD DE LA LAVADORA.................... 8

REQUISITOS DE INSTALACIÓN.......................8

Herramientas y piezas Requisitos de ubicación Sistema de desagüe

Requisitos eléctricos.....................................

INSTRUCCIONES DE INSTALACIÓN.......... 11

Antes de empezar

Quite el fleje de embalaje

Conecte la manguera de desagüe........

Conecte las mangueras de entrada..............12

Asegure la manguera de desagüe................13

Nivele la lavadora Complete la instalación

NÚMEROS DE SERVICIO

........

....................................

................................

.......................................

..........................................11

.............................

.........................................

.................................

„„„.„„..CONTRAPORTADA

.......

SECURITE DE LA LAVEUSE.....

EXIGENCES D’INSTALLATION

Outillage et pièces.........................................14

11 11

13 13

Exigences de remplacement d'installation 15

Système de vidange

Spécifications électriques.......

INSTRUCTIONS D’INSTALLATION,

Avant de commencer Élimination de la sangle d’expédition Raccordement du tuyau de vidange Raccordement des tuyaux d'arrivée d'eau 18 Immobilisation du tuyau de vidange Régiage de l’aplomb de la laveuse

Achever l’installation......................................19

NUMÉROS DE SERVICE

..............

.....................................

.....................................17

COUVERTURE ARRIÈRE

.....................

...

...................14

......................

...............

...........

.............

...............

15 16

17 17

19 19

WASHER SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.

This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.’ These words mean:

You can be killed or seriously Injured If you don't immediately

ADANGER

AWARNING

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

follow Instructions.

You can be killed or seriously injured if you don't follow instructions.

8537142

INSTALLATION REQUIREMENTS

Assemble the necessary tools and supplies before beginning the washer installation. The parts supplied are in the washer basket.

Tools needed for connecting the drain hose and water inlet hoses:

■ Pliers that open to 1 ®/i6 in. {3.95 cm)

■ Flashlight (optional)

Parts supplied:

/ytemate Parts

Parts listed are available from your local Sears store or Sears Service Center. For further information, call 1-800-4-MY-HOME®

(1-800-469-4663).

If You Have: You Will Need to Buy:

Laundry tub or

standpipe taller than 96 in. (2.4 m)

1 in. (2.5 cm) diameter standpipe

Sump pump system (if not already available)

2 in. (5 cm) diameter to 1 in. (2.5 cm) diameter standpipe adapter. Part No. 3363920

2. Sihsr, double-wire hose clamp

(for the bottom of the drain hose)

3. Yellow, single-wire hose clamp (for the top of the drain hose)

4. Water inlet hoses (2)

5. Flat water inlet hose washers (4)

Tools needed for securing the drain hose and leveling the washer:

■ Adjustable or open end wrench ®/i6 in. (14 mm)

■ Level

■ Wood block

■ Ruler or measuring tape

Parts supplied:

1. Shipping strap with fastener

2. Front leveling feet with nuts (2)

Overhead sewer Standard 20 gal. (76 L) 39 in. (99 cm) tall

Floor drain Siphon break, Part Number 285320;

Water faucets beyond reach of fill hoses

Drain hose too

short

Drain hose that is

too long

Lint clogged drain

Selecting the proper location for your washer improves performance and minimizes noise and possible washer “walk.”

Your washer can be installed in a basement, laundry room, closet, or recessed area. (See “Drain System.”)

drain tub or utility sink, sump pump and connectors (available from local plumbing suppliers)

additional drain hose. Part Number 3357090 and connector kit. Part Number 285442

2 longer water fill hoses: 6 ft (1.8 m) Part Number 76314, 10 ft (3.0 m) Part Number 350008

Drain hose. Part No. 388423 and hose kit. Part No. 285442

Hose kit, Part No. 285442

Drain protector. Part No. 367031

IMPORTANT: Do not install Or store the washer where it will be

exposed to the weather.

Proper installation is your responsibility.

You will need:

■ A water heater set to deliver 120°F (49°C) water to the

washer.

■ A grounded electrical outlet located within 4 ft (1.2 m) of where the power cord is attached to the back of the washer.

(See “Electrical Requirements.”)

■ Hot and cold water faucets located within 4 ft (1.2 m) of the hot and cold water fill valves, and water pressure of 5-100 psi

(34.5-690 kPa). Washers with triple dispensers require 20-100 psi (138-690 kPa) for best performance.

■ A level floor with a maximum slope of 1 In. (2.5 cm) under entire washer, installing the washer on carpeting is not recommended.

■ A sturdy floor to support the washer weight (washer, water and load) of 315 lbs (143 kgs).

Do not store or operate your washer in temperatures at or below 32®F {0°C). Some water can remain in the washer and can cause damage in low temperatures. See “Washer Care” in the Washer User instructions for winterizing information.

Recessed area or closet Installation

The dimensions shown are for the recommended spacing allowed, except the closet door ventilation openings. The dimensions shown for the closet door ventilation openings are the minimum required.

1. Front view

2. Side view

3. Closet door with vents

Additional spacing should be considered for ease of installation and servicing.

Additional clearances may be required for wall, door and floor moldings.

Additional spacing of 1 in. (2.5 cm) on ali sides of the washer is recommended to reduce noise transfer.

If a closet door is instalied, the minimum air openings in the

top and bottom of the door are required. Louvered doors with air openings in the top and bottom are acceptable.

Companion appliance spacing should also be considered.

The washer can be installed using the standpipe drain system (floor or wall), the laundry tub drain system, or the floor drain system. Select the drain hose installation method you need. See “Alternate Parts.”

The top of the standpipe must be at least 39 in. (99 cm) high and no higher than 96 in. (244 cm) from the bottom of the washer.

Laundry tub drain system (view 1)

The laundry tub needs a minimum 20 gal. (76 L) capacity. The top of the laundry tub must be at least 39 in. (99 cm) above the floor and no higher than 96 in. (244 cm) from the bottom of the washer.

Floor drain system (view 2)

The floor drain system requires a siphon break that may be purchased separately. See “Alternate Parts.”

The siphon break must be a minimum of 28 in. (71 cm) from the bottom of the washer. Additional hoses might be needed.

Electrical Reqijire'merits

^WARNING

Electrical Shock Hazard Plug Into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter. Do not use an extension cord. Failure to follow these instructions can result in death,

fire, or electrical shock.

Standpipe drain system - wall or floor (view 1 & 2)

The standpipe drain requires a minimum diameter standpipe of 2 in. (5 cm). The minimum carry-away capacity can be no less than 17 gal. (64 L) per minute. A 2 in. (5 cm) diameter to 1 in. (2.5 cm) diameter standpipe adapter kit is available. See “Alternate Parts.”

A 120-volt, 60-Hz., AC-only, 15- or 20-ampere, fused electrical supply is required. Time-delay fuse or circuit breaker is recommended. It is recommended that a separate circuit serving only this appliance be provided.

This washer is equipped with a power supply cord having a 3 prong ground plug.

To minimize possible shock hazard, the cord must be plugged into a mating, 3 prong, ground-type outlet, grounded in accordance with local codes and ordinances. If a mating outlet is not available, it is the personal responsibility and obligation of the customer to have the properly grounded outlet installed by a qualified electrician.

+ 5 hidden pages