Kenmore 10674949401, 10674944401, 10674942401, 10674939401, 10674934401 Owner’s Manual

...

Top-Mount Refrigerator

Refrigerador con montaje superior

R_frig_rateur superpos_

iiiiiiii_ii_iiiii_tJiiii,,_iiiii_::_,i!_!ii_¸,i:iiiiii::i_'I_iiiiii:iiiiiiii_ii!!!ii_,ii_!i:_!!i_!i:iii::iiii_i:iiiiii:i_,_i_i_! _i!!!!_,!I:i,_iiiiii_i!"'_i_!!!!!__iii_i!iii:i_ii_!!i!!!!_,Iilliii,_!i_iii!!_¸_!_'i

2302478 Sears Canada Inc., Toronto, Ontario, Canada M5B 2B8 www.sears.ca

Sears Roebuck and Co., Hoffman Estates, IL 60179 U.S.A. www.sears.com

TABLEOF CONTENTS

REFRIGERATOR WARRANTY

REFRIGERATOR WARRANTY ....................................................... 2

REFRIGERATOR SAFETY .............................................................. 3

Proper Disposal of Your Old Refrigerator .................................... 3

INSTALLATION INSTRUCTIONS .................................................. 4

Unpack the Refrigerator ............................................................... 4

Location Requirements ................................................................ 4

Electrical Requirements ................................................................ 5

Water Supply Requirements ........................................................ 5

Connect Water Supply ................................................................. 5

Refrigerator Doors ........................................................................ 6

Adjust the Doors ........................................................................... 9

Normal Sounds ............................................................................. 9

REFRIGERATOR USE ................................................................. 10

Ensuring Proper Air Circulation ................................................. 10

Using the Controls ..................................................................... 10

Ice Maker ................................................................................... 11

REFRIGERATOR FEATURES ..................................................... 11

Refrigerator Shelves .................................................................. 11

Crisper ....................................................................................... 12

Meat Drawer .............................................................................. 12

Wine or Can/Bottle Rack ........................................................... 12

Utility or Egg Bin ........................................................................ 12

FREEZER FEATURES ................................................................. 13

Freezer Shelf .............................................................................. 13

Pull-out Freezer Floor ................................................................ 13

DOOR FEATURES ....................................................................... 13

Door Rails .................................................................................. 13

Can Racks and Door Bins ......................................................... 14

Adjustable Utility Compartment & Tray ..................................... 14

Flip-up Door Shelf ..................................................................... 14

REFRIGERATOR CARE ............................................................... 14

Cleaning ..................................................................................... 14

Changing the Light Bulbs .......................................................... 15

Power Interruptions ................................................................... 15

Vacation and Moving Care ........................................................ 15

TROUBLESHOOTING .................................................................. 16

PROTECTION AGREEMENTS .................................................... 18

In the U.S.A ................................................................................ 18

In Canada .................................................................................. 18

ACCESSORIES ............................................................................ 18

SERVICE NUMBERS ............................................... BACK COVER

ONE-YEAR FULL WARRANTY ON REFRIGERATOR

For one year from the date of purchase, when this refrigerator is operated and maintained according to the instructions supplied with it, Sears will repair this refrigerator, free of charge, if defective in material or workmanship. This time period does not include the refrigerator water filter cartridge (if equipped), which is an expendable part warranted for only 30 days (see below).

FIVE-YEAR FULL WARRANTY ON SEALED REFRIGERATION SYSTEM

For five years from the date of purchase, when this refrigerator is operated and maintained according to the instructions supplied with it, Sears will repair the sealed system (consisting of refrigerant, connecting tubing, and compressor), free of charge, if defective in materials or workmanship.

30-DAY FULL WARRANTY ON WATER FILTER CARTRIDGE (if equipped)

For thirty days from the date of purchase, Sears will replace the refrigerator water filter cartridge if it is defective in materials or workmanship.

All above warranty coverage applies only to refrigerators which are used for storage of food for private household

purposes.

Warranty service is available in the United States or Canada by contacting Sears at 1-800-4-MY-HOME ®(1-800-469-4663).

This warranty applies only while this product is in use in the

United States or Canada.

This warranty gives you specific legal rights, and you may also

have other rights which vary from state to state or province to province.

Sears, Roebuck and Co.

Dept. 817WA, Hoffman Estates, IL 60179

Sears Canada Inc.

Toronto, Ontario, Canada M5B 2B8

Product Record

In the space below, record your complete model number, serial number, and purchase date. You can find this information on the

model and serial number label located on the inside wall of the refrigerator compartment.

Have this information available to help you obtain assistance or service more quickly whenever you contact Sears concerning

your refrigerator.

Model number 106.

Serial number

Purchase date

Save these instructions and your sales receipt for future reference.

REFRIGERATOR SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of fire, electric shock, or injury when using your refrigerator, follow these basic precautions:

_,Plug into a grounded 3 prong outlet, mUse nonflammable cleaner. _,Do not remove ground prong.

_,Do not use an adapter. _,Do not use an extension cord.

_,Disconnect power before servicing. _,Replace all parts and panels before operating.

_,Remove doors from your old refrigerator.

SAVE THESE INSTRUCTIONS

mKeep flammable materials and vapors, such as gasoline,

away from refrigerator. mUse two or more people to move and install refrigerator. mDisconnect power before installing ice maker (on ice maker

kit ready models only). mUse a sturdy glass when dispensing ice or water (on some

models).

Proper Disposal of Your Old Refrigerator

IMPORTANT: Child entrapment and suffocation are not problems of the past. Junked or abandoned refrigerators are still dangerous

- even if they will sit for "just a few days." If you are getting rid of your old refrigerator, please follow these instructions to help prevent accidents.

Before You Throw Away Your Old Refrigerator or Freezer:

• Take off the doors.

• Leave the shelves in place so that children may not easily climb inside.

INSTALLATION INSTRUCTIONS

Excessive Weight Hazard

Use two or more people to move and install refrigerator.

Failure to do so can result in back or other injury.

Remove the Packaging

Remove tape and glue residue from surfaces before turning on the refrigerator. Rub a small amount of liquid dish soap

over the adhesive with your fingers. Wipe with warm water and dry.

Do not use sharp instruments, rubbing alcohol, flammable fluids, or abrasive cleaners to remove tape or glue. These products can damage the surface of your refrigerator. For

more information, see "Refrigerator Safety." On some models, shelves, bins, door shelf rails, and other

feature parts may be packaged in the Interior FeaturePak. Follow the instructions contained in the package for proper assembly.

There are four bolts that secure the refrigerator to the shipping case. Keep these bolts because they are the

refrigerator's leveling legs.

• Properly dispose of packaging. IMPORTANT: Do not remove the white foam air return insert that

is located behind the control panel on the ceiling of the refrigerator (on some models). The insert is part of the refrigerator and not part of the packing material. If the insert is removed, ice

may migrate down from the freezer and cause icicles to form.

When Moving Your Refrigerator: Your refrigerator is heavy. When moving the refrigerator

for cleaning or service, be sure to protect the floor. Always pull the refrigerator straight out when moving it. Do not wiggle or "walk" the refrigerator when trying to move it, as floor damage could occur.

Clean Before Using

After you remove all of the package materials, clean the inside of your refrigerator before using it. See the cleaning instructions in

"Refrigerator Care."

_mportant information to know about glass she_ves

and covers:

Do not clean glass shelves or covers with warm water when they are cold. Shelves and covers may break if exposed to sudden temperature changes or impact, such as bumping. For your protection, tempered glass is designed to shatter into many small, pebbb-size pieces. This is normal. GIass shelves and covers are heavy. Use special care when removing them to avoid impact from dropping.

Explosion Hazard

Keep flammable materials and vapors, such as gasoline, away from refrigerator.

Failure to do so can result in death, explosion, or fire.

To ensure proper ventilation for your refrigerator, allow for a 1/2"

(1.25 cm) space on each side and at the top. When installing your refrigerator next to a fixed wall, leave 2" (5.08 cm) minimum clearance on each side (some models require more) to allow for

the door to swing open. If your refrigerator has an ice maker,

allow extra space at the back for the water line connections. NOTE: It is recommended that you do not install the refrigerator

near an oven, radiator, or other heat source. Do not install the refrigerator in a location where the temperature will fall below 55°F (13°C).

1/2"H.25 ore)

r-qF-q

2" (5.08era)

ElectricamShockHazard

Pmugintoagrounded3 prong outlet,

Do not remove ground prong, Do not use an adapter, Do not use an extension cord,

Failure to follow these instructions can result in death, fire, or eiectricam shock,

Before you move your refrigerator into its final location, it is important to make sure you have the proper electrical

connection.

Recommended Grounding Method

A 115 Volt, 60 Hz., AC only 15- or 20-amp fused, grounded electrical supply is required. It is recommended that a separate circuit serving only your refrigerator be provided. Use an outlet that cannot be turned off by a switch. Do not use an

extension cord. NOTE: Before performing any type of installation, cleaning, or

removing a light bulb, turn the control (Thermostat, Refrigerator or Freezer Control depending on the model) to OFF and then disconnect the refrigerator from the electrical source. When you are finished, reconnect the refrigerator to the electrical source and reset the control (Thermostat, Refrigerator or Freezer Control depending on the model) to the desired setting.

Read all directions carefully before you begin,

IMPORTANT:

• If you turn the refrigerator on before the water line is connected, turn the ice maker OFR

• All installations must meet local plumbing code requirements.

• Use copper tubing and check for leaks. Install copper tubing only in areas where the household temperatures will remain above freezing.

TOOLS NEEDED: Flat-blade screwdriver, 7/16IIand 1/211open-end wrenches or two adjustable wrenches, 1/4"nut driver and drill bit, hand drill or electric drill (properly grounded). Gather the required tools and parts before starting installation, Read and follow the instructions provided with any tools listed.

NOTE: Your refrigerator dealer has a kit available with a 1/4" (6.35 mm) saddle-type shutoff valve, a union, and copper tubing. Before purchasing, make sure a saddle-type valve complies with your local plumbing codes. Do not use a piercing-type or 3/16" (4.76 mm) saddle valve which reduces water flow and clogs more easily.

Water Pressure

A cold water supply with water pressure of between 30 and 120 psi (207-827 kPa) is required to operate ice maker. If you have questions about your water pressure, call a licensed, qualified plumber.

Reverse Osmosis Water Supply

IMPORTANT: The pressure of the water supply coming out of a reverse osmosis system going to the water inlet valve of the refrigerator needs to be between 30 and 120 psi (207 - 827 kPa)

If a reverse osmosis water filtration system is connected to your cold water supply, the water pressure to the reverse osmosis system needs to be a minimum of 40 to 60 psi (276 - 414 kPa).

If the water pressure to the reverse osmosis system is less than 40 to 60 psi (276 - 414 kPa):

• Check to see whether the sediment filter in the reverse osmosis system is blocked. Replace the filter if necessary.

• Allow the storage tank on the reverse osmosis system to refill after heavy usage.

If you have questions about your water pressure, call a licensed, qualified plumber.

Connect to Water Line

1. Unplug refrigerator or disconnect power.

2. Turn OFF main water supply. Turn ON nearest faucet long enough to clear line of water.

3. Locate a 1/2"to 11/4'' (1.25 cm to 3.18 cm) vertical cold water pipe near the refrigerator.

IMPORTANT:

• Make sure it is a cold water pipe.

• Horizontal pipe will work, but drill on the top side of the

pipe, not the bottom. This will help keep water away from the drill and normal sediment from collecting in the valve.

4. Determine the length of copper tubing you need. Measure from the connection on the lower left rear of refrigerator to the water pipe. Add 7 ft. (2.1 m) to allow for cleaning. Use 1/4" (6.35 mm) O.D. (outside diameter) copper tubing. Be sure both ends of copper tubing are cut square.

5. Using a grounded drill, drill a 1/4"hole in the cold water pipe you have selected.

.........A

Q ...... .................

A. Cold water pipe E.Compression sleeve B. Pipe clamp F. Shutoff valve C. Copper tubing G.Packing nut D. Compressionnut

6. Fasten the shutoff valve to the cold water pipe with the pipe clamp. Be sure the outlet end is solidly in the 1/4"drilled hole in the water pipe and that the washer is under the pipe clamp. Tighten the packing nut. Tighten the pipe clamp screws carefully and evenly so washer makes a watertight seal. Do not overtighten or you may crush the copper tubing.

7. Slip the compression sleeve and compression nut on the copper tubing as shown. Insert the end of the tubing into the outlet end squarely as far as it will go. Screw compression nut onto outlet end with adjustable wrench. Do not overtighten.

8. Place the free end of the tubing in a container or sink, and turn ON the main water supply. Flush the tubing until water is clear. Turn OFF the shutoff valve on the water pipe. Coil the copper tubing.

Connect to Refrigerator

TOOLS NEEDED: s_6" hex-head socket wrench, #2 Phillips

screwdriver, flat-blade screwdriver, %6" open-end wrench, flat 2" putty knife.

IMPORTANT:

• Unplug refrigerator or disconnect power.

• Remove food and any adjustable door or utility bins from doors.

• If you only want to remove and replace the doors, see "Remove Doors and Hinges" and "Replace Doors and Hinges."

• All graphics referenced in the following instructions are included later in this section after "Final Steps."

1. Attach the copper tube to the valve inlet using a compression nut and sleeve as shown. Tighten the compression nut. Do not overtighten. Use the tube clamp on the back of the refrigerator to secure the tubing to the refrigerator as shown. This will help prevent damage to the tubing when the refrigerator is pushed back against the wall.

2. Turn shutoff valve ON.

3. Check for leaks. Tighten any connections (including connections at the valve) or nuts that leak.

C D

A. Tube clamp B. Copper tubing

C, Compression nut D. Valve inlet

4. The ice maker is equipped with a built-in water strainer. If your water conditions require a second water strainer, install it in the 1/4"(6.35 mm) water line at either tube connection. Obtain a water strainer from your nearest appliance dealer.

5. Plug in refrigerator or reconnect power.

Remove Doors and Hinges

"5/16"Hex-Head Hinge Screw

Unplug refrigerator or disconnect power.

Open refrigerator door and remove base grille from the bottom front of the refrigerator. See Base Grille graphic.

Close the refrigerator door and keep both doors closed until you are ready to lift them free from the cabinet.

NOTE: Provide additional support for the doors while the hinges are being moved. Do not depend on the door magnets to hold the doors in place while you are working.

4. Remove the parts for the top hinge as shown in Top Hinge graphic. Lift the freezer door free from the cabinet.

5. Remove the parts for the center hinge as shown in the Center Hinge graphic. Lift the refrigerator door free from the cabinet.

6. Remove the parts for the bottom hinge as shown in the Bottom Hinge graphic.

Reverse Doors (optional)

IMPORTANT: If you want to reverse your doors so that they open in the opposite direction, follow these steps. If you are not reversing the doors, see "Replace Doors and Hinges."

Door Stop Screw

Door Handle Sealing Screw

DoorHinge Hole Plug

Cabinet Hinge Hole Plug

4. Remove door handle sealing screws. Move to opposite side of refrigerator door as shown in Graphic 4.

5. Remove door handle seal screw front. Move to opposite side of refrigerator door as shown in Graphic 7.

6. Remove door stop. Move to opposite side of refrigerator door as shown in Graphic 5.

7. Position refrigerator handle on opposite side of the refrigerator door as shown in Graphic 6-3. Drive top two screws in handle first. Align lower portion of handle and drive

bottom screw.

8. Align refrigerator handle bottom trim. Slide trim into place and attach bottom screw. See Graphic 6-1.

9. Tighten all screws. Set aside refrigerator door until bottom hinge is installed on product.

Flat-Head Handle Screw

Door Handle Seal Screw Front

Cabinet

1. Remove ¾6" hex-head hinge screws from handle side and

move them to opposite side. See Graphic 1-1.

2. Remove cabinet hinge hole plugs from cabinet top and move them to opposite side hinge holes as shown in Graphic 1-2.

Freezer Door

1. Remove freezer handle assembly as shown, Keep all parts together. See Graphic 2.

2. Remove door hinge hole plug. Move to opposite side as shown in Graphic 3.

3. Remove door handle sealing screws. Move to opposite side of freezer door as shown in Graphic 4,

4. Remove door stop. Move to opposite side of freezer door as shown in Graphic 5.

5. Position freezer handle on opposite side of freezer door. Assemble handles on door as shown in Graphic 2.

6. Tighten all screws. Set aside door until hinges and refrigerator compartment door are in place.

Refrigerator Door

1. Remove refrigerator handle bottom trim. Remove screw from bottom of door and slide trim down as shown in Graphic 6-1.

2. Remove refrigerator handle assembly as shown. Keep all parts together. See Graphic 6-3.

3. Remove door hinge hole plug from refrigerator door. Move to opposite side hinge hole as shown in Graphic 3.

Round-HeadHandle Screw

Shoulder Handle Screw

Replace Doors and Hinges

NOTE: Graphic may be reversed if door swing is reversed.

1. Replace the parts for the bottom hinge as shown. Tighten screws. See Bottom Hinge graphic. Replace the refrigerator

door. NOTE: Provide additional support for the doors while the

hinges are being moved. Do not depend on the door magnets to hold the doors in place while you are working.

2. Assemble the parts for the center hinge as shown and tighten all screws. See Center Hinge graphic. Replace the freezer

door.

3. Assemble the parts for the top hinge as shown in Top Hinge graphic. Do not tighten screws completely.

4. Line up the doors so that the bottom of the freezer door aligns evenly with the top of the refrigerator door. Tighten all

screws.

Final Steps

1. Check all holes to make sure that hole plugs and screws are in place. Reinstall top hinge cover. See Top Hinge graphic.

2. Replace the base grille. See Base Grille graphic.

3. Plug in refrigerator or reconnect power.

4. Return all removable door parts to doors and food to refrigerator.

BaseGrille

TopHinge

A. Top Hinge Cover

B.5/_,,Hex-Head Hinge Screws C. Top Hinge

Center Hinge

[]

[[

A. Door Hinge Hole Plug

A.5/_8"Hex-Head Hinge Screws

Flat-Head Handle Screws Freezer Door Handle

__ h ........A

A. Door Handle Sealing Screws

Front View Side View

A. Center Hinge

B.5/_,,Hex-Head Hinge Screws

Bottom Hinge

A. Bottom Hinge B. 5/_8"Hex-Head Hinge Screws

,u 1

A. Door Stop Screw A B B. Door Stop

A ..........................................................

A. Shoulder

Handle Screw

A. Door Handle

Seal Screw Front

A. Flat-Head

Handle Screw

B. Round-Head

Handle Screw

Door Closing

Your refrigerator has two front adjustable rollers - one on the right and one on the left. If your refrigerator seems unsteady or you want the doors to close easier, adjust the refrigerator's tilt using

the instructions below.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong. Do not use an adapter. Do not use an extension cord.

Failure to follow these instructions can result in death, fire, or eiectrica_ shock.

1. Plug into a grounded 3 prong outlet.

Excessive Weight Hazard

Use two or more people to move and install refrigerator.

Failure to do so can result in back or other injury.

Move the refrigerator into its final location.

Remove the base grille. See Base Grille graphic. The two leveling screws are part of the front roller assemblies which are at the base of the refrigerator on either side.

Use a screwdriver to adjust the leveling screws. Turn the leveling screw to the right to raise that side of the refrigerator

or turn the leveling screw to the left to lower that side. It may take several turns of the leveling screws to adjust the tilt of

the refrigerator. NOTE: Having someone push against the top of the

refrigerator takes some weight off the leveling screws and rollers. This makes it easier to adjust the screws.

5. Open both doors again and check to make sure that they close as easily as you like. If not, tilt the refrigerator slightly more to the rear by turning both leveling screws to the right. It may take several more turns, and you should turn both leveling screws the same amount.

6. Replace the base grille.

Align Doors

If the space between your doors looks uneven, you can adjust it using the instructions below:

1. Pry off the top hinge cover.

2. Loosen the top hinge screws using a 5/16"socket or wrench.

3. Have someone hold the door in place or put a spacer between the doors while you tighten the top hinge screws.

4. Replace the top hinge cover.

Your new refrigerator may make sounds that your old one didn't make. Because the sounds are new to you, you might be

concerned about them. Most of the new sounds are normal. Hard surfaces, such as the floor, walls, and cabinets, can make the

sounds seem louder. The following describes the kinds of sounds and what may be making them.

• If your refrigerator is equipped with an ice maker, you will hear a buzzing sound when the water valve opens to fill the ice maker for each cycle.

Your refrigerator is designed to run more efficiently, to keep your food items at the desired temperatures and to minimize energy usage. The high efficiency compressor and fans may cause your refrigerator to run longer than your old one. You may also hear a pulsating or high-pitched sound from the compressor or fans adjusting to optimize performance.

• You may hear the evaporator fan motor circulating air through the refrigerator and freezer compartments. The fan speed may increase as you open the doors or add warm food.

• Rattling noises may come from the flow of refrigerant, the water line, or items stored on top of the refrigerator.

• Water dripping on the defrost heater during a defrost cycle may cause a sizzling sound.

• As each cycle ends, you may hear a gurgling sound due to the refrigerant flowing in your refrigerator.

• Contraction and expansion of the inside walls may cause a popping noise.

• You may hear air being forced over the condenser by the condenser fan.

• You may hear water running into the drain pan during the defrost cycle.

REFRIGERATOR USE

_!!i!ii_i_iii_:,!!i;;_i_jiiiii_iii;il_!!iiiiiii:::::;_',_l%;_!iii::i:_,_!:!:i_ii_,_ii_ii_i_i_ii_¸¸_Ciiii_,o_ii:iiii;;,'_!_iiI:iio_ii_

In order to ensure proper temperatures, you need to permit airflow between the refrigerator and freezer sections. As shown in the illustration, cool air enters through the bottom of the freezer section and moves up. Most of the air then flows through the

freezer section vents and recirculates under the freezer floor. The rest of the air enters the refrigerator section through the top vent.

Do not block any of these vents with food packages. If the vents are blocked, airflow will be prevented and temperature and moisture problems may occur.

IMPORTANT: Because air circulates between both sections, any odors formed in one section will transfer to the other. You must

thoroughly clean both sections to eliminate odors. To prevent odor transfer and drying out of food, wrap or cover foods tightly.

For your convenience, your refrigerator controls are preset at the factory. When you first install your refrigerator, make sure that the controls are still preset to the mid-settings as shown.

NOTE: To turn your refrigerator off, turn the refrigerator control to the word OFF or until the word OFF appears. Your product will not cool when the refrigerator control is set to OFE

Mid-setting "3"

OFF

5 1

COLDES@

NO£NN.

Mid-setting "4"

IMPORTANT:

• Give your refrigerator time to cool down completely before adding food. It is best to wait 24 hours before you put food into the refrigerator.

If you add food before the refrigerator has cooled completely, your food may spoil. Adjusting the Refrigerator and Freezer Controls to a higher (colder) than recommended setting will not cool the compartments any faster.

Adjusting Controls

The mid-settings indicated in the previous section should be

correct for normal household usage. The controls are set correctly when milk or juice is as cold as you like and when ice

cream is firm. If the temperature is too warm or too cold in the refrigerator or

freezer, first check the air vents to be sure they are not blocked.

If you need to adjust temperatures, use the settings listed in the chart below as a guide. On models with two controls, adjust the refrigerator temperature first. Wait at least 24 hours between adjustments and then recheck the temperatures.

......................................i

CONDITION/REASON: ADJUSTMENT:

REFRIGERATOR section too warm Adjust REFRIGERATOR

- Door opened often, large amount or TEMPERATURE of food added or room Control one setting

temperature very warm higher FREEZER section too warm/ice

not made fast enough

- Door opened often, or large

Adjust FREEZER or TEMPERATURE Control

one setting higher

amount of food added or very cold room temperature (can't cycle often enough)

- Heavy ice usage REFRIGERATOR section too cold

- Controls not set correctly for your conditions

Adjust REFRIGERATOR or TEMPERATURE

Control one setting lower

FREEZER section too cold Adjust FREEZER or

- Controls not set correctly for TEMPERATURE Control your conditions one setting lower

Turning the Ice Maker On/Off

NOTE: Do not force the wire shutoff arm up or down.

• Toturn the ice maker on, simply lower the wire shutoff arm. NOTE: Your ice maker has an automatic shutoff. As ice is

made, the ice cubes will fill the ice storage bin and the ice cubes will raise the wire shutoff arm to the OFF (arm up) position.

• To manually turn the ice maker off, lift the wire shutoff arm to the OFF (arm up) position and listen for the click to make sure the ice maker will not continue to operate.

REFRIGERATOR FEATURES

Your model may have some or all of these features. Features that can be purchased separately as product accessories are labeled with the word "Accessory." Not all accessories will fit all models. If you are interested in purchasing one of the accessories, please

call 1-80O-4-MY-HOME ®.

_mportant information to know about glass she_vee

and covers:

Do not clean glass shelves or covers with warm water when

they are cold. Shelves and covers may break if exposed to

sudden temperature changes or impact, such as bumping. For your protection, tempered glass is designed to shatter into many small, pebble-size pieces. This is normal. Glass shelves and covers are heavy. Use specia! care when removing them to avoid impact from dropping.

Your model may have glass or wire shelves. Store similar foods together and adjust the shelves to fit different heights. This reduces the time the refrigerator door is open and saves energy.

Ice Production Rate

NORMAL Ice Production: The ice maker should produce approximately 8 to 12 batches of ice in a 24-hour period. If ice is not being made fast enough, turn the Freezer Control toward a higher (colder) number in half number steps. (For example, if the control is at 3, move it to between 3 and 4.) Wait 24 hours and, if necessary, gradually turn the Freezer Control to the highest setting, waiting 24 hours between each

increase. MAXIMUM Ice Production (on some models): The ice maker

should produce approximately 16 to 20 batches of ice in a 24-hour period. If your refrigerator has the maximum ice production feature, push the switch to MAX.

Remember

• Allow 24 hours to produce the first batch of ice. Discard the first three batches of ice produced.

The quality of your ice will be only as good as the quality of the water supplied to your ice maker. Avoid connecting the ice maker to a softened water supply. Water softener chemicals (such as salt) can damage parts of the ice maker and lead to poor quality ice. If a softened water supply cannot be avoided, make sure the water softener is operating properly and is well maintained.

• Do not store anything on top of the ice maker or in the ice storage bin.

Slide-out Shelves (on some models)

To Remove and Replace a Shelf in a Metal Frame:

1. Pull the shelf forward to the stop. Tilt the front of the shelf up and lift it slightly as you pull the shelf from the frame.

2. Replace the shelf by guiding it back into the slots on the frame and pushing the shelf in past the stop.

Shelves and Shelf Frames

To Remove and Replace a Shelf/Frame:

1. Remove the shelf/frame by tilting it up at the front and lifting it out of the shelf supports.

2. Replace the shelf/frame by guiding the rear shelf hooks into the shelf supports. Tilt the front of the shelf up until rear shelf

hooks drop into the shelf supports. Check to make sure that the shelf is securely in position.

Crisper Drawers

Meat Drawer Cover

To Remove and Replace a Drawer:.

1. Slide drawer straight out to the stop. Lift the front of the

drawer and slide it out the rest of the way.

2. Replace a drawer by sliding it back in fully past the stop.

Crisper Cover

To Remove the Crisper(s) Cover:

1. Remove crisper(s). Hold the glass insert firmly with one hand

and press up in the center of the glass insert until it rises above the plastic frame. Carefully slide the glass insert

forward to remove.

2. Lift the cover frame and remove it.

To Replace the Crisper(s) Cover: NOTE: Before reinstalling the cover, make sure the U-shaped

reinforcement bar is reinstalled in the front edge of the crisper coven

1. Fit back of cover frame into supports on side walls of the refrigerator and lower the front of the cover frame into place.

2. Slide rear of glass insert into cover frame and lower front into place.

To Remove and Replace the Meat Drawer Cover:

1. Remove the meat drawer. Tilt up the front of the cover and lift at the back. Pull the cover straight out.

2. Replace the cover by guiding the rear hooks into the shelf supports. Tilt the cover up at the front until the rear hooks drop into the slots. Lower the front of the cover to a level position and replace the meat drawer.

Meat Storage Guide

Store most meat in original wrapping as long as it is airtight and moisture-proof. Rewrap if necessary. See the following chart for storage times. When storing meat longer than the times given,

freeze the meat.

Fresh fish or shellfish ......................... use same day as purchased

Chicken, ground beef, variety meats (liver) ...................... 1-2 days

Cold cuts, steaks/roasts ................................................... 3-5 days

Cured meats ................................................................... 7-10 days

Leftovers - Cover leftovers with plastic wrap, aluminum foil, or plastic containers with tight lids.

Crisper Humidity Control (on some models)

The humidity control is located on the crisper drawer. You can adjust the amount of humidity in the moisture-sealed crisper

using the settings between HIGH and LOW. LOW (open) lets moist air out of the crisper for best storage of

fruits and vegetables with skins.

• Fruit: Wash, let dry and store in refrigerator in plastic bag in crisper. Do not wash or hull berries until they are ready to use.

Sort and keep berries in original container in crisper.

• Vegetables with skins: Place in plastic bag or plastic container and store in crisper.

HIGH (closed) keeps moist air in the crisper for best storage of fresh, leafy vegetables.

• Leafy vegetables: Wash in cold water, drain and trim or tear off bruised and discolored areas. Place in plastic bag or

plastic container and store in crisper.

: s : s: [

To Remove and Replace the Wine Rack (left) or Can/Bottle Rack (right):

1. Remove the rack by pulling it straight out from the shelf.

2. Replace the rack by sliding it in between the shelf and the wall of the refrigerator.

:©_: _o: s o:ss:::

Depending on your model, you may have a one, two or three piece bin. Eggs may be stored in the egg tray or loose in the bin.

NOTE: Store eggs in a covered container for long-term storage. If

your model does not have an egg storage bin, store eggs in their

original carton on an interior shelf.

FREEZER FEATURES

call 1-800-4-MY-HOME ®.

To Remove and Replace the Shelf:

1. Removethe shelf by lifting the entire shelf slightly and moving

it all the way to the left-hand side. Tilt the right-hand side up and out of the shelf supports.

2. Replace the shelf by inserting the left-hand end all the way into the shelf supports. Then, lower the right-hand end of the shelf and insert it into the shelf supports.

NOTE: The shelf should lower slightly and lock into place. If the shelf does not appear stable, make sure both ends of the shelf are inserted into the shelf supports.

Frozen Food Storage Guide

Storage times will vary according to the quality and type of food, the type of packaging or wrap used (should be airtight and moisture-proof), and the storage temperature. Seal the package or container securely to prevent taste and odor transfer throughout the product. Ice crystals inside a sealed package are

normal. Put no more unfrozen food into the freezer than will freeze within

24 hours (no more than 2 to 3 Ibs. of food per cubic foot [907- 1,350 g per 28 L] of freezer space). Leave enough space in the freezer for air to circulate around packages. The freezer door must close tightly. For more information on preparing food for freezing, check a freezer guide or reliable cookbook.

DOOR FEATURES

call 1-800-4-MY-HOME ®.

The door rails may be removed for easier cleaning.

Snap-on Door Rails

To Remove and Replace the Freezer Floor:

1. Lift both back "fences" up and out.

2. Remove the freezer floor by pulling it out about 1" (2.5 cm) with one hand around the air tower section (center back) and

one hand at center front.

3. Lift up floor at rear until hooks release from cabinet and pull the floor out the rest of the way.

4. Replace the freezer floor by sliding the floor straight in until the hooks drop into place at rear of cabinet.

5. Replace "fences" by aligning pins with socket in the floor, and pushing down until they snap into place.

To Remove and Replace the Rails:

1. Remove the rails by pushing in slightly on the front of the bracket while pulling out on the inside tab. Repeat these steps for the other end of the rail.

2. Replace the rails by aligning the ends of the brackets with the buttons on the sides of the door liner. Firmly snap bracket and rail assembly onto the tabs above the shelf as shown.

Drop-in Door Rails

To Remove and Replace the Rails:

1. Remove the rails by pulling straight up on each end of the rail.

2. Replace the rails by sliding the shelf rail into the slots on the door and pushing the rail straight down until it stops.

_iiiiiii:ii::_!:_i_ii:::_i:i;iC:i!,,_:::S;%_'iid[)OOi,;¸_ilii!!i!i,ii_ii_:_!_;;

NOTE: Can racks may be purchased as an Accessory for some models.

To Remove and Replace the Racks/Bins:

1. Remove the racWbin by lifting it and pulling it straight out.

2. Replace the racWbin by sliding it in above the desired support and pushing it down until it stops.

REFRIGERATOR CARE

Explosion Hazard

Use nonflammable cleaner. Failure to do so can resumt in death, explosion, or fire°

The utility compartment and tray slide from one side to the other for more flexible storage. The tray fits on either side of the utility compartment or partially underneath it. Try moving it to different positions to find the option that works best for you.

To Install and Adjust the Utility Compartment and Tray:

1. Insert the front of the utility tray into the slot on the back of the shelf rail. Lower the back of the tray into position.

2. Place the front of the utility compartment on top of the shelf rail. Lower the back of the compartment onto the ribs on the refrigerator door.

Adjust the utility compartment by lifting the front slightly and sliding it to the desired position. Lower the front to lock it into place.

The shelf bottom flips up so you can store taller items in the door shelf below. When in the down position, the shelf is strong enough to hold up to 10 Ibs. (4.5 kg).

Both the refrigerator and freezer sections defrost automatically. However, clean both sections about once a month to prevent

odors from building up. Wipe up spills immediately.

To Clean Your Refrigerator:

1. Unplug refrigerator or disconnect power.

2. Remove all removable parts from inside, such as shelves, crispers, etc.

3. Hand wash, rinse, and dry removable parts and interior surfaces thoroughly. Use a clean sponge or soft cloth and a mild detergent in warm water.

• Do not use abrasive or harsh cleaners such as window

sprays, scouring cleansers, flammable fluids, cleaning waxes, concentrated detergents, bleaches or cleansers

containing petroleum products on plastic parts, interior and door liners or gaskets. Do not use paper towels,

scouring pads, or other harsh cleaning tools. These can scratch or damage materials.

• To help remove odors, you can wash interior walls with a

mixture of warm water and baking soda (2 tbs to 1 qt

[26 g to 0.95 L] of water).

4. Determine whether your refrigerator exterior is painted metal, brushed aluminum or stainless steel and choose the

appropriate cleaning method. Painted metal: Wash exteriors with a clean sponge or soft

cloth and a mild detergent in warm water. Do not use abrasive or harsh cleaners, or cleaners designed for stainless steel. Dry thoroughly with a soft cloth. For additional protection against damage to painted metal exteriors, apply appliance wax (or auto paste wax) with a clean, soft cloth. Do not wax plastic parts.

Brushed aluminum: Wash with a clean sponge or soft cloth and a mild detergent in warm water. Do not use abrasive or

harsh cleaners, or cleaners designed for stainless steel. Dry thoroughly with a soft cloth.

Stainless steel finish: Wash with a clean sponge or soft cloth and a mild detergent in warm water. Do not use abrasive or harsh cleaners. Dry thoroughly with a soft cloth.

To keep your stainless steel refrigerator looking like new and to remove minor scuffs or marks, it is suggested that you use the manufacturer's approved Stainless Steel Cleaner & Polish. To order the cleaner, see the

"Accessories" section.

IMPORTANT: This cleaner is for stainless steel parts only! Do not allow the Stainless Steel Cleaner & Polish to come into

contact with any plastic parts such as the trim pieces, dispenser covers or door gaskets. If accidental contact does occur, clean plastic part with a sponge and mild detergent in warm water. Dry thoroughly with a soft cloth.

There is no need for routine condenser cleaning in normal home operating environments. If the environment is particularly greasy or dusty, or there is significant pet traffic in the home, the condenser should be cleaned every 2 to 3 months to ensure maximum efficiency.

If you need to clean the condenser:

• Remove the base grille. See "Base Grille" graphic or "Base Grille" section.

• Use a vacuum cleaner with a soft brush to clean the grille, the open areas behind the grille and the front surface area

of the condenser.

• Replace the base grille when finished.

Plug in refrigerator or reconnect power.

NOTE: Not all bulbs will fit your refrigerator. Be sure to replace the bulb with one of the same size, shape, and wattage.

1. Unplug refrigerator or disconnect power.

2. Remove the bulb from behind the control panel in the refrigerator or from behind the light shield in the freezer (on some models). Replace it with a bulb of the same wattage.

3. Plug in refrigerator or reconnect power.

If the power will be out for 24 hours or less, keep the door or doors closed (depending on your model) to help food stay cold and frozen.

If the power will be out for more than 24 hours, do one of the following:

• Remove all frozen food and store it in a frozen food locker.

• Place 2 Ibs. (907 g) of dry ice in the freezer for every cubic foot (28 L) of freezer space. This will keep the food frozen for 2 to 4 days.

• If neither a food locker nor dry ice is available, consume or can perishable food at once.

REMEMBER: A full freezer stays cold longer than a partially filled one. A freezer full of meat stays cold longer than a freezer full of baked goods. If you see that food contains ice crystals, it may be refrozen, although the quality and flavor may be affected. If the condition of the food is poor, dispose of it.

Vacations

If You Choose to Leave the Refrigerator On While You're

Away:

1. Use up any perishables and freeze other items.

2. If your refrigerator has an automatic ice maker:

• Raise wire shutoff arm to OFF (up) position or move the switch to the OFF (right) setting.

• Shut off water supply to the ice maker.

3. Empty the ice bin.

If You Choose to Turn the Refrigerator Off Before You Leave:

1. Remove all food from the refrigerator.

2. If your refrigerator has an automatic ice maker:

• Turn off the water supply to the ice maker at least one day ahead of time.

• When the last load of ice drops, raise the wire shutoff arm to the OFF (up) position or move the switch to the OFF (right) setting.

3. Depending on the model, turn the Thermostat Control or Refrigerator Control to OFR See "Using the Controls."

4. Clean refrigerator, wipe it, and dry well.

5. Tape rubber or wood blocks to the tops of both doors to prop them open far enough for air to get in. This stops odor and mold from building up.

Moving

When you are moving your refrigerator to a new home, follow these steps to prepare it for the move.

1. If your refrigerator has an automatic ice maker:

• Turn off the water supply to the ice maker at least one day

ahead of time.

• Disconnect the water line from the back of the

refrigerator.

• When the last load of ice drops, raise the wire shutoff arm

to the OFF (up) position or move the switch to the OFF (right) setting.

2. Remove all food from the refrigerator and pack all frozen food in dry ice.

3. Empty the ice bin.

4. Depending on the model, turn the Thermostat Control or

Refrigerator Control to OFR See "Using the Controls."

5. Unplug refrigerator.

6. Empty water from the defrost pan.

7. Clean, wipe, and dry thoroughly.

8. Take out all removable parts, wrap them well, and tape them together so they don't shift and rattle during the move.

9. Depending on the model, raise the front of the refrigerator so

it rolls more easily OR screw in the leveling legs so they don't scrape the floor. See "Adjust the Doors."

10. Tape the doors closed and tape the power cord to the back of the refrigerator.

When you get to your new home, put everything back and refer to the "Installation Instructions" section for preparation instructions. Also, if your refrigerator has an automatic ice maker, remember to reconnect the water supply to the refrigerator.

TROUBLESHOOTING

Trythe solutions suggested here first in order to avoid the cost of an unnecessary service call.

Are the doors opened often? Expect the motor to run longer

Your refrigerator will not operate

• Is the power supply cord unplugged? Plug into a grounded 3 prong outlet.

• Has a household fuse blown, or has a circuit breaker • tripped? Replace the fuse or reset the circuit.

• Is the Temperature Control turned to the OFF position? See "Using the Control(s)," depending on the model. •

• Is the refrigerator defrosting? Recheck to see whether the refrigerator is operating in 30 minutes. Your refrigerator will regularly run an automatic defrost cycle.

The lights do not work

• Is the power supply cord unplugged? Plug into a grounded 3 prong outlet.

• Is a light bulb loose in the socket or burned out? See "Changing the Light Bulb(s)," depending on the model.

There is water in the defrost drain pan

• Is the refrigerator defrosting? The water will evaporate. It is normal for water to drip into the defrost pan.

• Is it more humid than normal? Expect that the water in the defrost pan will take longer to evaporate. This is normal when

it is hot or humid.

The motor seems to run too much

Is the room temperature hotter than normal? Expect the • motor to run longer under warm conditions. At normal room

temperatures, expect your motor to run about 40% to 80% of the time. Under warmer conditions, expect it to run even •

more of the time.

Has a large amount of food just been added to the refrigerator? Adding a large amount of food warms the

refrigerator. It is normal for the motor to run longer in order to cool the refrigerator back down. See "Refrigerator Features."

when this occurs. In order to conserve energy, try to get everything you need out of the refrigerator at once, keep food organized so it is easy to find, and close the door as soon as

the food is removed.

Is the control set correctly for the surrounding conditions? See "Using the Control(s)," depending on the

model. Are the doors closed completely? Push the doors firmly

shut. Ifthey will not shut all the way. See "The doors will not close completely" later in this section.

NOTE: Your new refrigerator will run longer than your old one due

to its high-efficiency motor.

The refrigerator seems to make too much noise

• The sounds may be normal for your refrigerator. See "Normal Sounds."

The ice maker is not producing ice or not enough ice

• Has the ice maker just been installed? Wait 72 hours for full ice production to begin. Once your refrigerator is cooled, the ice maker should produce 70-120 cubes every 24 hours.

Is the freezer temperature cold enough to produce ice?

Wait 24 hours after hookup for ice production. See "Using the Control(s)," depending on the model.

Is the wire shutoff arm in the OFF (arm up) position? Lower the wire shutoff arm to the ON (arm down) position.

See "Ice Maker."

Is the water line shutoff valve to the refrigerator turned on? Turn on the water valve. See "Connect the Water

Supply."

Does the ice maker mold have water in it or has no ice been produced? Be sure your refrigerator has been

connected to a water supply and the supply shutoff valve is turned on. See "Connect the Water Supply."

Is an ice cube jammed in the ejector arm? Remove the ice from the ejector arm with a plastic utensil. See "Ice Maker."

• Has a large amount of ice just been removed? Allow 24 hours for ice maker to produce more ice.

• Is the control set correctly? If too little ice is produced, see "Using the Control(s)," depending on the model.

• Is a reverse osmosis water filtration system connected to your cold water supply? See "Water Supply Requirements."

NOTE: If not due to any of the above, there may be a problem with the water line. Call for service.

Off-taste or gray color in the ice

There is interior moisture buildup

• Are the plumbing connections new, causing discolored or off-flavored ice? Discard the first few batches of ice.

• Have the ice cubes been stored for too long? Throw away old ice and make a new supply.

• Has food in the refrigerator been wrapped properly? See "Refrigerator Features,"

• Do the freezer and ice bin need to be cleaned? See "Cleaning."

• Does the water contain minerals (such as sulfur)? A filter may need to be installed to remove the minerals.

The divider between the two compartments is warm

The warmth is probably due to normal operation of the automatic exterior moisture control. If still concerned, call for service.

Temperature is too warm

Are the air vents blocked in either compartment? This

prevents the movement of cold air from the freezer to the refrigerator. Remove any objects from in front of the air vents.

See "Ensuring Proper Air Circulation" for the location of air vents.

Are the door(s) opened often? Be aware that the refrigerator will warm when this occurs, In order to keep the refrigerator cool, try to get everything you need out of the refrigerator at once, keep food organized so it is easy to find, and close the

door as soon as the food is removed.

Has a large amount of food just been added to the refrigerator or freezer? Adding a large amount of food

warms the refrigerator. It can take several hours for the refrigerator to return to the normal temperature,

• Are the controls set correctly for the surrounding conditions? See "Using the Control(s)," depending on the model.

• Are the air vents blocked in the refrigerator? Remove any objects from in front of the air vents. See "Ensuring Proper Air

Circulation" for the location of air vents. Are the door(s) opened often? To avoid humidity buildup,

try to get everything you need out of the refrigerator at once, keep food organized so it is easy to find, and close the door as soon as the food is removed. When the door is opened, humidity from the room air enters the refrigerator. The more often the door is opened, the faster humidity builds up, especially when the room itself is very humid.

Is the room humid? It is normal for moisture to build up inside the refrigerator when the room air is humid.

Is the food packaged correctly? Check that all food is securely wrapped, Wipe off damp food containers before placing in the refrigerator.

Are the controls set correctly for the surrounding conditions? See "Using the Control(s)," depending on the

model. Was a self-defrost cycle completed? It is normal for

droplets to form on the back wall after the refrigerator self- defrosts.

The doors will not close completely

• Are food packages blocking the door open? Rearrange containers so that they fit more tightly and take up less space.

Is the ice bin out of position? Push the ice bin in all the way. Are the crisper cover, pans, shelves, bins, or baskets out

of position? Put the crisper cover and all pans, shelves, bins, and baskets back into their correct positions. See "Refrigerator Features."

Are the gaskets sticking? Clean gaskets and the surface that they touch. Rub a thin coat of paraffin wax on the

gaskets following cleaning, Does the refrigerator wobble or seem unstable? Level the

refrigerator. See "Door Closing," Were the doors removed during product installation and

not properly replaced? Remove and replace the doors according to "Refrigerator Doors," or call a qualified service

technician.

+ 39 hidden pages

Kenmore 10674949401, 10674944401, 10674942401, 10674939401, 10674934401 Owner’s Manual

Specifications and Main Features

Frequently Asked Questions

User Manual