Kenmore 10659542990, 10659085891, 10659047991, 10658785891, 10658599891 Owner’s Manual

...

Side by Side Refrigerator

Refrigerador de dos puertas

G L_ (,]<:,I(]I_J

R_fri _rateur c6te & c6te

..+<.........=+..,,_..>.:+I..,I.................................i;91 ..,.,J__;........_< == ,.>.+I._<.I_+==_<

Sears Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.

2200128 Sears Canada, Inc., Toronto, Ontario, Canada M5B 2B8 www.sears.com

TABLEOF

WARRANTY

CONTENTS

WARRANTY ......................................................................... 2

REFRIGERATOR SAFETY ................................................ 3

PARTS AND FEATURES .................................................. 4

INSTALLING YOUR REFRIGERATOR ............................... 5

Unpacking Your Refrigerator ............................................. 5

Space Requirements ......................................................... 5

Electrical Requirements ..................................................... 6

Removing the Doors .......................................................... 6

Removing the Door Handles ............................................. 7

Water System Preparation ................................................ 7

Connecting the Refrigerator to a Water Source ................ 8

Base Grille .......................................................................... 9

Door Closing ...................................................................... 9

Understanding Sounds You May Hear ........................... 10

USING YOUR REFRIGERATOR ....................................... 10

Ensuring Proper Air Circulation ....................................... 10

Setting the Controls ......................................................... 11

Adjusting Control Settings ............................................... 11

Food Storage Guide ........................................................ 11

REFRIGERATOR FEATURES ........................................... 13

Ice Maker Storage Bin ..................................................... 13

Water and Ice Dispensers ............................................... 13

Water Filtration and Monitoring System .......................... 15

Refrigerator Shelves ........................................................ 16

Lateral Shelf ..................................................................... 17

Convertible Vegetable/Meat Drawer and Cover ............. 17

Convertible Vegetable/Meat Drawer

Temperature Control ....................................................... 18

Crisper and Crisper Cover ............................................... 18

Crisper Humidity Control ................................................. 18

Crisper Cover Extension .................................................. 19

Dell Drawer ....................................................................... 19

Door Rails ........................................................................ 19

Door Bins ......................................................................... 19

Freezer Shelf .................................................................... 20

Freezer Basket ................................................................. 20

CARING FOR YOUR REFRIGERATOR ............................ 20

Cleaning Your Refrigerator .............................................. 20

Changing the Light Bulbs ................................................ 21

Power Interruptions ......................................................... 22

Vacation and Moving Care .............................................. 22

TROUBLESHOOTING ....................................................... 23

SEARS MAINTENANCE AGREEMENT ............................ 27

WATER FILTER CERTIFICATIONS ................................ 28

FULL ONE-YEAR WARRANTY ON REFRIGERATOR

For one year from the date of purchase, when this refrigerator is operated and maintained according to

instructions attached to or furnished with the product,

Sears will repair this refrigerator, free of charge, if defective

in material or workmanship.

FULL FIVE-YEAR WARRANTY ON SEALED REFRIGERATION SYSTEM

For five years from the date of purchase, when this refrigerator is operated and maintained according to

owner's instructions attached to or furnished with the

product, Sears will repair the sealed system (consisting of refrigeration, connecting tubing, and compressor), free of

charge, if defective in materials or workmanship. The above warranty coverage applies only to refrigerators

which are used for storage of food for private household

purposes and excludes original and replacement Kenmore Filtered Ice & Water filter cartridges (if equipped with the

filter system). Original and replacement cartridges are warranted for 30 days, parts only, against defects in

material or workmanship.

WARRANTY SERVICE IS AVAILABLE BY CONTACTING THE NEAREST SEARS SERVICE CENTER IN THE

UNITED STATES OR CANADA.

This warranty applies only while this product is in use in the United States or Canada. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state or province to province.

Warranty terms may vary in Canada. Contact your local Sears Service Center for complete details.

Sears, Roebuck and Co.

D/817WA, Hoffman Estates, IL 60179

Sears Canada, Inc., Toronto, Ontario, Canada M5B 2B8

In the space below, record your complete model number,

serial number, and purchase date. You can find this

information on the model and serial number label, located

as shown in the Parts And Features section of this book.

Have this information available to help you obtain

assistance or service more quickly whenever you contact Sears concerning your refrigerator.

Model number 106.

Serial number

Purchase date

Save these instructions and your sales receipt for future reference.

REFRIGERATOR SAFETY

Your safety and the safety of others is very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.

This isthe safety alert symbol. This symbol alerts you to hazards that can kill or hurt you and others.

All safety messages will be preceded by the safety alert symbol and the word "DANGER" or "WARNING." These words mean:

You will be killed or seriously injured if you don't follow instructions.

You can be killed or seriously injured if you don't

follow instructions.

All safety messages will identify the hazard, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

IMPORTANTSAFETYINSTRUCTIONS

WARNING - To reduce the risk of fire, electric shock, or injury when using your refrigerator, follow these basic

precautions:

• Plug into a grounded 3 prong outlet.

• Do not remove ground prong.

• Do not use an adapter.

• Do not use an extension cord.

• Disconnect power before servicing.

• Replace all panels before operating. Remove doors from your old refrigerator.

• Use nonflammable cleaner.

• Keep flammable materials and vapors, such as gasoline, away from refrigerator.

• Use two or more people to move and install

refrigerator.

• Disconnect power before installing ice maker.

• Use a sturdy glass when dispensing ice or water (on some models).

m SAVETHESEINSTRUCTIONS

IMPORTANT - Child entrapment and suffocation are not

problems of the past. Junked or abandoned refrigerators are still dangerous - even if they will sit for "just a few days." tf you are getting rid of your old refrigerator, please follow the instructions below to help prevent accidents.

Before you throw away your old refrigerator or freezer:

• Take off the doors.

• Leave the shelves in place so that children may not easily climb inside.

PARTS AND FEATURES

This manual covers several different models. The refrigerator you have purchased may have some or all of the items listed. The locations of the features may not match your model.

10 11 12 13

IIII

--22

1. Light

2. Automatic Ice Maker

3. Ice Bin

4. Drop-in Door Rails

5. Light

6. Removable Shelves

7. Snap-on Door Rails

8. Freezer Bins/Baskets (on some models)

9. Leveling Rollers (behind base grille)

10. Slide-out Shelves

11. Control Panel

12. Light Switch

13. Refrigerator Light

14. Water Filtration System (on some models)

14 15 16

15. Base Grille

16. Convertible Vegetable/Meat Drawer Temperature Control (on side wall)

17. Model and Serial Number Label (on side wall)

18. Dairy Compartment

19. Utility Bin

20. Door Bins (on some models)

21. Dell Drawer (on some models)

22. Crisper Light (on some models)

23. Slide-out Crisper Cover (on some models)

24. Crisper Drawer

25. Convertible Vegetable/Meat Drawer

26. Convertible Vegetable/Meat Drawer Cover

INSTALLING YOUR

REFRIGERATOR

Explosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from refrigerator.

Failure to do so can result in death, explosion, or fire.

Removing packaging materials

• Remove tape and any labels from your refrigerator before using (except the model and serial number label).

To remove any remaining tape or glue, rub the area briskly with your thumb. Tape or glue residue can also be easily removed by rubbing a small amount of liquid dish soap over the adhesive with your fingers. Wipe with warm water and dry.

• Do not use sharp instruments, rubbing alcohol, flammable fluids, or abrasive cleaners to remove tape or glue. These products can damage the surface of your refrigerator. For more information, see the "Important Safety Instructions" section.

IMPORTANT: Do not remove any permanent instruction labels inside your refrigerator, or the Tech Sheet that is

fastened to the base grille.

Cleaning before use

After you remove all of the packaging materials, clean the

inside of your refrigerator before using it. See the cleaning instructions in the "Caring for your Refrigerator" section.

• To ensure proper ventilation for your refrigerator, allow for a .5" (1.25 cm) space on each side and at the top.

.5" (1.25cm) '

• If your refrigerator has an ice maker, make sure you leave some extra space at the back for the water line

connections. The refrigerator can be flush against the back wall if you do not have an ice maker installed.

• If you are installing your refrigerator next to a fixed wall, leave 2" (5.08 cm) minimum on each side (depending on

your model) to allow for the door to swing open.

NOTE: Do not install the refrigerator near an oven, radiator,

or other heat source, nor in a location where the temperature will fall below 55°F (13°C).

Electrical Shock Hazard

Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter.

Do not use an extension cord. Failure to follow these instructions can result in

death, fire, or electrical shock.

Before you move your refrigerator into its final location, it is important to make sure you have the proper electrical

connection:

Ill&

Recommended Grounding Method

A 115 Volt, 60 Hz., AC only 15 or 20 ampere fused, grounded electrical supply is required. It is recommended

that a separate circuit serving only your refrigerator be

provided. Use an outlet that cannot be turned off by a

switch. Do not use an extension cord.

Electrical Shock Hazard

Disconnect power before removing doors. Failure to do so can result in death or

electrical shock.

NOTE: Before removing doors, open both doors and remove base grille (see the "Base Grille" section).

Tools Needed:

V4-inch hex-head socket wrench and 5/_6-inchhex-head

socket wrench.

1. Unplug refrigerator or disconnect power supply.

2. If you have a dispenser (ice or water), disconnect water line (behind base grille).

• Remove hose from clip.

• Disconnect union nut and slide it back onto tube.

• Remove metal insert from tube.

• Remove union nut and spring.

NOTE: Before performing any type of installation, cleaning,

or removing a light bulb, turn the Thermostat Control (or

Refrigerator Control depending on the model) to OFF and

then disconnect the refrigerator from the electrical source. When you are finished, reconnect the refrigerator to the

electrical source and reset the Thermostat Control (or

Refrigerator Control) to the desired setting.

3. Remove left top hinge.

• Remove hinge cover and screws. DO NOT

REMOVE SCREW 1 AS SHOWN IN DIAGRAM.

• Disconnect wiring plug and both ground wires.

• Carefully lift door up off bottom hinge. Make sure

you protect water line from damage.

Apply firm pressure with hand on face of trim. Slide top trim up and bottom trim down away from handle, then lift

off of shoulder screws. Remove screws.

4. Disassemble right top hinge.

• Remove hinge cover and screws. DO NOT

REMOVE SCREW 2 AS SHOWN IN DIAGRAM.

• Lift door up off bottom hinge.

I i i

5. Remove bottom hinge, if necessary. Both bottom hinges have similar construction. DO NOT REMOVE

SCREW 3 AS SHOWN IN DIAGRAM. NOTE: It may not be necessary to remove the bottom

hinge to move refrigerator through a doorway.

PLEASE READ BEFORE INSTALLATION

Immediately after installation, follow the steps below

to make sure that the water system is properly cleaned.

1. Turn off the ice maker by opening the freezer door and lifting up the signal arm as shown.

6. Replace doors.

7. Plug in refrigerator or reconnect power.

2. Flush the water system by dispensing and discarding 2 - 3 gallons (approximately 6-7 minutes) of water through the dispenser. This will clean the system and help clean air from the lines. Additional flushing may be required in some households.

3. Turn on the ice maker by opening the freezer door and Connecting to water line: lowering the signal arm as shown.

1. Unplug refrigerator or disconnect power.

2. Turn OFF main water supply. Turn ON nearest faucet long enough to clear line of water.

3. Find a 1/2-inchto 11/4-inch vertical COLD water pipe near the refrigerator.

NOTE: Horizontal pipe will work, but the following precaution must be taken: Drill on the top side of the pipe, not the bottom. This will help keep water away from the drill. This also keeps normal sediment from

4. Allow 24 hours to produce the first batch of ice. tce maker should then produce approximately 7 to 9 batches of ice in a 24-hour period. Discard the first three batches of ice produced.

collecting in the valve.

To determine the length of copper tubing you will need, measure from connection on lower left rear of

refrigerator to water pipe. Add 7 feet (2.1 m) to allow for moving refrigerator for cleaning. Use 1/4-inchO.D.

(outside diameter) copper tubing. Be sure both ends of copper tubing are cut square.

5. Using a grounded drill, drill a V4-inch hole in the cold

Read all directions carefully before you begin.

water pipe you have selected.

IMPORTANT:

• If operating the refrigerator before installing the water connection, turn ice maker to the OFF position to

prevent operation without water.

• All installations must be in accordance with local plumbing code requirements.

• Use copper tubing and check for leaks.

• Install copper tubing only in areas where temperatures will remain above freezing.

• It may take up to 24 hours for your ice maker to begin producing ice.

Tools required:

• Standard screwdriver

• %_-inch and 1/2-inchopen-end wrenches or two adjustable wrenches

• V4dnch nut driver

• V4-inch drill bit

• Hand drill or electric drill (properly grounded)

NOTE: Your refrigerator dealer has a kit available with a V4- inch saddle-type shut-off valve, a union, and copper tub-

ing. Before purchasing, make sure a saddle-type valve

complies with your local plumbing codes. Do not use a

piercing-type or s/_6-inchsaddle valve which reduces water

flow and clogs more easily.

Cold Water Supply

The ice maker water valve contains a flow washer which is

used as a water pressure regulator. The ice maker needs to be connected to a cold water line with water pressure between 30 and 120 psi. If a problem occurs, call your utility company.

Fasten shut-off valve to cold water pipe with pipe clamp. Be sure outlet end is solidly in the 1/4-inchdrilled hole in the water pipe and that washer is under the pipe clamp. Tighten packing nut. Tighten the pipe clamp screws carefully and evenly so washer makes a watertight seal. Do not overtighten or you may crush the copper tubing, especially if soft (coiled) copper tubing is used. Now you are ready to connect the copper tubing.

Slip compression sleeve and compression nut on copper tubing as shown. Insert end of tubing into outlet end squarely as far as it will go. Screw compression nut onto outlet end with adjustable wrench. Do not overtighten.

Place the free end of the tubing into a container or sink, and turn ON main water supply and flush out tubing

until water is clear. Turn OFF shut-off valve on the water pipe. Coil copper tubing.

6 5

1. Cold Water Pipe

2. Pipe Clamp

3. Copper Tubing

4. Compression Nut

5. Compression Sleeve

6. Shut Off Valve

7. Packing Nut

Connecting to refrigerator:

To replace the grille:

1. Attach the copper tube to the valve inlet using a compression nut and sleeve as shown. Tighten the compression nut. Do not overtighten. Use the tube clamp on the back of the refrigerator to secure the tubing to the refrigerator as shown. This will help prevent damage to the tubing when the refrigerator is pushed back against the wall. Move to step 2.

2. Turn shut-off valve ON. Check For Leaks. Tighten any connections (including connections at the valve) or nuts

that leak.

1. Tube Clamp

2. Copper tubing

3. Compression Nut

4. Valve Inlet

1. Open the doors.

2. Line up the grille support tabs with the metal clips.

3. Push the grille firmly to snap it into place.

Door Closing

Your refrigerator has 2 front adjustable rollers -- one on the right and one on the left. tf your refrigerator seems

unsteady or you want the doors to close easier, adjust the refrigerator's tilt using the instructions below:

1. Plug in refrigerator.

2. Move the refrigerator into its final position.

3. Remove the base grille (see "Base Grille" earlier in this section). The two leveling screws are part of the front

roller assemblies which are at the base of the refrigerator on either side.

4. Use a screwdriver to adjust the leveling screws. Turn the leveling screw to the right to raise that side of the

refrigerator or turn the leveling screw to the left to lower that side. It may take several turns of the leveling

screws to adjust the tilt of the refrigerator. NOTE: Having someone push against the top of the

refrigerator takes some weight off the leveling screws and rollers. This makes it easier to adjust the screws.

3. The ice maker is equipped with a built-in water strainer. If local water conditions require periodic cleaning or a well is your source of water supply, a second water

strainer should be installed in the 1/4-inch water line. Obtain a water strainer from your nearest appliance

dealer. Install at either tube connection.

4. Plug in refrigerator or reconnect power.

To remove the base grille:

1. Open both refrigerator doors.

2. Place hands along the ends of the grille, with your thumbs along the top. Push in with your thumbs and

pull up on the bottom.

NOTE: Be sure to refasten the Tech Sheet behind the base

grille after cleaning.

5. Open both doors again and check to make sure that they close as easily as you like. If not, tilt the refrigerator slightly more to the rear by turning both leveling screws to the right. It may take several more turns, and you should turn both leveling screws the same amount.

6. Replace the base grille.

USING YOUR

Your new refrigerator may make sounds that your old one didn't make. Because the sounds are new to you, you

might be concerned about them. Most of the new sounds

are normal. Hard surfaces, like the floor, walls, and cabinets, can make the sounds seem louder than they

actually are. The following describes the kinds of sounds and what may be making them.

• If your product is equipped with an ice maker, you will hear a buzzing sound when the water valve opens to fill

the ice maker for each cycle.

• The defrost timer will click when the automatic defrost cycle begins and ends. Also, the thermostat refrigera- tor control, will click when cycling on and off.

• Rattling noises may come from the flow of refrigerant, the water line, or items stored on top of the refrigerator.

• Your refrigerator is designed to run more efficiently to keep your food items at the desired temperature. The

high efficiency compressor may cause your new refrigerator to run longer than your old one, and you

may hear a pulsating or high-pitched sound.

• Water dripping on the defrost heater during a defrost cycle may cause a sizzling sound.

• You may hear the evaporator fan motor circulating the air through the refrigerator and freezer compartments.

• As each cycle ends, you may hear a gurgling sound due to the refrigerant flowing in your refrigerator.

• Contraction and expansion of the inside walls may cause a popping noise.

• You may hear air being forced over the condenser by the condenser fan.

• You may hear water running into the drain pan during the defrost cycle.

REFRIGERATOR

In order to ensure proper temperatures, you need to permit

air to flow between the two sections. Cold air enters the

bottom of the freezer section and moves up. Itthen enters

the refrigerator section through the top vent. Air then

returns to the freezer as shown.

Do not block any of these vents with food such as soda,

cereal, bread, etc. If the vents are blocked, airflow will be

prevented and the temperature controls will not function properly.

IMPORTANT: Because air circulates between both

sections, any odors formed in one section will transfer to the other. You must thoroughly clean both sections to eliminate odors. To prevent odor transfer from food, wrap or cover foods tightly.

Checking airflow

To measure the amount of cold air being directed from the freezer compartment into the refrigerator section, hold your hand in front of the top vent. You can adjust the Air

Balance Control to feel the different amounts of airflow. For further information on temperatures inside your

refrigerator, refer to the "Troubleshooting" section.

For your convenience, the refrigerator controls are

preset at the factory. When you first install your

refrigerator, make sure that the controls are still preset.

The Thermostat Control and the Air Balance Control should both be at the "mid-settings" as shown in the

illustrations below.

The Thermostat Control adjusts both the refrigerator and freezer compartment temperatures. Settings to the

left of the mid-setting make the overall temperature in both

compartments less cold. Settings to the right of the mid- setting make the overall temperature in both compart-

ments colder.

THERMOSTAT

a 3 4 D

22_ 5 m

WARMEST I {// IIII ))1 6 COLDEST

NOTE: Your refrigerator will not cool when the Thermostat

Control is set to OFE

The Air Balance Control divides the amount of cold air entering both compartments. Settings to the left of the

mid-setting direct more cold air into the refrigerator

compart-ment. Settings to the right of the mid-setting direct more cold air into the freezer compartment.

If you need to adjust temperatures in the refrigerator or freezer, use the settings listed in the chart below as a guide. Wait at least 24 hours between adjustments.

RECOMMENDED

CONDITION/REASON: ADJUSTMENT:

REFRIGERATOR section

too warm

Turn

AIR BALANCE

Control one-half

• Door opened often

• Large amount of food added

setting higher, wait 24 hours,

then check the

• Room temperature very warm

freezer

temperature

FREEZER section too warm/ice not made fast enough

• Door opened often

Turn AIR

BALANCE Control

one-half setting

higher

• Large amount of food added

• Very cold room temperature (can't cycle often enough)

• Heavyice usage

• Air diffuser blocked by items

Move packages

out of airstream

REFRIGERATOR section

too cold

Turn

THERMOSTAT

Control to next

• Controls not set correctly for

lower number

your conditions

AIR BALANCE

COLDAIRTO FRE£ZER

COMPARTMENT

_ ERECTS MORE

Give your refrigerator time to cool down completely before adding food. It is best to wait 24 hours before you put food

into the refrigerator.

IMPORTANT: If you add food before the refrigerator has cooled completely, your food may spoil. Turning the Ther- mostat and Air Balance Controls to a higher (colder) than recommended setting will not cool the compartments any faster.

Give the refrigerator time to cool down completely before adding food. It is best to wait 24 hours before you put food

into the refrigerator. The settings indicated in the previous section should be correct for normal household

refrigerator usage. The controls are set correctly when milk or juice is as cold as you like and when ice cream is firm.

FREEZER section too cold

Turn AIR

BALANCE Control

• Controls not set correctly for your conditions

one-half setting

lower

Storing Fresh Food

Wrap or store food in the refrigerator in airtight and

moisture-proof material unless otherwise noted. This prevents food odor and taste transfer throughout the

refrigerator. For dated products, check code date to

ensure freshness.

Butter or margarine

Keep opened butter in covered dish or closed

compartment. When storing an extra supply, wrap in freezer packaging and freeze.

Cheese Store in the original wrapping until you are ready to use

it. Once opened, rewrap tightly in plastic wrap or

aluminum foil.

Milk

Wipe milk cartons. For best storage, place milk on

interior shelf.

Eggs

Store in original carton on interior shelf.

Fruit

Wash, let dry, and store in refrigerator in plastic bags or crisper. Do not wash or hull berries until they are ready to use. Sort and keep berries in original container in a crisper, or store in a loosely closed paper bag on a

refrigerator shelf. Leafy vegetables

Remove store wrapping and trim or tear off bruised and

discolored areas. Wash in cold water and drain. Place in

plastic bag or plastic container and store in crisper.

Vegetables with skins (carrots, peppers)

Place in plastic bags or plastic container and store in

crisper.

Fish Use fresh fish and shellfish the same day as purchased.

Meat

Store most meat in original wrapping as long as it is airtight and moisture-proof. Rewrap if necessary. See the following chart for storage times. When storing meat

longer than the times given, freeze the meat.

Chicken ........................................................... 1-2 days

Ground beef .................................................... 1-2 clays

Variety meats (liver, heart, etc.) ....................... 1-2 days

Cold cuts ......................................................... 3-5 days

Steaks/roasts .................................................. 3-5 days

Cured meats ................................................. 7-10 days

Leftovers

Cover leftovers with plastic wrap or aluminum foil.

Plastic containers with tight lids can also be used.

Storing Frozen Food

NOTE: For further information about preparing food for

freezing or food storage times, check a freezer guide or

reliable cookbook.

Packaging

Successful freezing depends on the correct packaging. When you close and seal the package you must not allow air or moisture in or out. If you do, you could have food odor and taste transfer throughout the refrigerator, and also dry out frozen food.

Packaging recommendations:

• Rigid plastic containers with tight-fitting lids

• Straight-sided canning/freezing jars

• Heavy-duty aluminum foil

• Plastic-coated paper

• Non-permeable plastic wraps (made from saran film)

• Specified freezer self-sealing plastic bags

Follow package or container instructions for proper

freezing methods.

Do not use:

• Bread wrappers

• Non-polyethylene plastic containers

• Containers without tight lids

• Wax paper or wax-coated freezer wrap

• Thin, semi-permeable wrap

Freezing

Your freezer will not quick-freeze any large quantity of food. Put no more unfrozen food into the freezer than will

freeze within 24 hours (no more than 2 to 3 Ibs of food per cubic foot [907-1,350 g per liter] of freezer space). Leave enough space in the freezer for air to circulate around

packages. Be careful to leave enough room at the front so

the door can close tightly. Storage times will vary according to the quality and type of

food, the type of packaging or wrap used, (airtight and

moisture-proof), and the storage temperature. Ice crystals

inside a sealed package are normal. This simply means that moisture in the food and air inside the package have condensed, creating ice crystals.

NOTE: Allow hot foods to cool at room temperature for 30

minutes, then package and freeze. Cooling hot foods

before freezing saves energy.

REFRIGERATOR

FEATURES

To remove the ice bin:

1. Pull the covering panel out from the bottom and then slide it back toward the rear.

2. Lift the signal arm so it clicks into the OFF (up) position.

Ice can still be dispensed, but no more can be made.

(on s e modes

Cut Hazard

Use a sturdy glass when dispensing ice or water.

Failure to do so can result in cuts.

Depending on your model, you may have one or more of the following options: the ability to select either crushed or cubed ice, a special light that turns on when you use the dispenser, or a lock option to avoid accidental dispensing.

The ice dispenser

Ice dispenses from the ice maker storage bin in the freezer. When the dispenser lever is pressed:

• A trapdoor opens in a chute between the dispenser and

the ice bin.

3. Lift up the front of the storage bin and pull it out.

4. Empty the ice bin. Use warm water to melt the ice if

necessary. Never use anything sharp to break up the ice in the bin. This can cause damage to the bin and the dispenser mechanism.

5. Wash with a mild detergent, rinse well and dry thoroughly. Do not use harsh or abrasive cleaners or

solvents.

6. When you replace the bin, make sure it is pushed in all the way or the dispenser will not work. Then push the signal arm down to the ON position to restart ice production. Make sure the door is closed tightly.

• Ice moves from the bin and falls through the chute.

• When you release the dispenser lever, the trap door closes and the ice dispensing stops. The dispensing system will not operate when the freezer door is open.

Some models dispense both cubed and crushed ice.

Before dispensing ice, select which type of ice you prefer. The button controls are designed for easy use and cleaning.

• For cubed ice, press the CUBE button until the red

indicator appears in the window above the CUBE button.

ICE

CRUSH CUBE

• For crushed ice, press the CRUSH button until the red

indicator appears in the window above the CRUSH button.

For crushed ice, cubes are crushed before being dispensed. This may cause a slight delay when dispensing

crushed ice. Noise from the ice crusher is normal, and

pieces of ice may vary in size. When changing from CRUSH to CUBE, a few ounces of crushed ice will be

dispensed along with the first cubes.

To dispense ice:

To dispense water:

1. Press button for the desired type of ice.

2. Press a sturdy glass against the ice dispenser lever. Hold the glass close to the dispenser opening so ice does not fall outside of the glass.

IMPORTANT: You do not need to apply a lot of pressure to the lever in order to activate the ice dispenser. Pressing hard will not make the ice dispense faster or in greater quantities.

3. Remove the glass to stop dispensing. NOTE: The first few batches of ice may have an off-

flavor from new plumbing and parts. Throw the ice away. Also, take large amounts of ice from the ice bin, not through the dispenser.

The water dispenser

Chilled water comes from a container behind the meat drawer. It holds approximately 11/2quarts (1.5 L).

When the refrigerator is first hooked up, press the water dispenser bar with a glass or jar until you draw and dis- card 2 or 3 quarts (1.9 to 2.8 L). It will take three to four

minutes for the water to begin dispensing. The water you

draw and discard rinses the tank and pipes. Allow several hours to chill a new tankful.

IMPORTANT: The small removable tray at the bottom of the dispenser is designed to catch small spills and allow for easy cleaning. There is no drain in the tray. The tray can

be removed from the dispenser and carried to the sink to

be emptied or cleaned.

1. Press a glass against the water dispenser lever.

2. Remove the glass to stop dispensing. NOTE: Dispense enough water every week to maintain a

fresh supply.

The dispenser light

The dispenser area has a light. It can be turned on

manually by pressing the "ON" button at the right hand

side of the control panel. The red indicator above the "ON"

button will appear. On some models: whenever you use

the dispenser the lever will automatically turn the light on.

LIGHT

OFF ON

NOTE: See the "Changing the Light Bulbs" section for information on changing the dispenser light bulb.

On models without crushed ice, the light switch is a

rocker-style type. Push the switch to turn the light on, and push again to turn the light off.

The dispenser lock (onsomemodels)

Your dispenser can be turned off for easy cleaning or to

prevent accidental dispensing by small children and pets.

To turn off the dispenser, press the LOCK button. The

indicator will appear above the LOCK button and the ice

and water dispensers will not work. To unlock the dispenser, press the UNLOCK button until the indicator appears. Then continue to dispense ice or water as usual.

DISPENSER

LOCK UNLOC i

NOTE: The lock feature does not shut off power to the

product, to the ice maker, or to the dispenser light. It

simply deactivates the dispenser levers.

The water filter status light

The water filter status light will help you know when to change your water filter cartridge. The light is located at

the top of the refrigerator compartment. The light will change from green to yellow. This tells you that it is almost

time to change the water filter cartridge (90% of the filter

life has been used). It is recommended that you replace

the water filter cartridge when the water filter status light changes to red OR water flow to your water dispenser or

ice maker decreases noticeably. (See "Changing a water

filter cartridge" later in this section.)

NOTE: Do not use with water that is microbiologicaliy unsafe or of unknown quality without adequate disinfection before or after the system.

3. Take the new cartridge out of its packaging and remove

protective cover from o-rings.

4. Slide the cartridge cap onto the new cartridge as shown.

WATER FILTER STATUS

GREEN* FILTERIS OK

YELLOW• LOW FILTERLIFE

RED• REPLACEFILTER

RESETWAYER FILTER STATUS PRESSLIGHTSWITCH (5)TIMES

After changing the water filter cartridge, reset the water filter status light by pressing the light switch 5 times within

10 seconds. The status light will change from red to green

when the system is reset.

Changing a water filter cartridge

The water filter is located below the freezer compartment door.

1. Locate the water filter cartridge cap in the front base grille below the freezer compartment door. Rotate the cap counterclockwise to a vertical position and pull the cap and filter cartridge out through the base grille.

NOTE: There will be water in the cartridge. Some spilling may occur.

5. With cartridge cap in the vertical position, push the new filter cartridge into the base grille until it stops. Rotate

the cartridge cap clockwise to a horizontal position.

6. RUN WATER THROUGH THE DISPENSER UNTIL THE WATER RUNS CLEAR (about 2 to 3 gallons or 6 to 7

minutes). This will clean the system and clear air from the lines. Additional flushing may be required in some

households. NOTE: As air is cleared from the system, water may

spurt out of the dispenser.

2. Remove the cartridge cap by sliding it off the end of the old cartridge. The cap will slide to the left or right. DO

NOT DISCARD THE CAR

Using the dispenser without the water filter

You can run the dispenser without a water filter cartridge. Your water will not be filtered. If you run the dispenser without a water filter cartridge, keep the cartridge cap and

replace it in the base grille for future use.

1. Remove the water filter cartridge (See "Changing a water filter cartridge" earlier in this section.) Then slide the cartridge cap off the end of the filter cartridge. DO

NOT DISCARD THE CAR

2. With the cartridge cap in the vertical position, insert the cap into the base grille until it stops.

3. Rotate the cartridge cap to a horizontal position. NOTE: The cartridge cap may not be even with the

base grille.

To remove shelves from the shipping position (shelves are shipped upside down):

1. Grasp front of upper shelf with one hand and use other hand to remove packing material from shelf area.

2. Lower front of upper shelf until shelf hooks can be removed from slots in shelf supports on the back refrigerator wall. Pull shelf forward to remove.

3. Flip shelf over.

4. Insert rear shelf hooks into slots in shelf supports.

5. Tilt front of shelf up until rear hooks drop into slots.

6. Lower front of shelf. Check to make sure that shelf is securely in position.

Slide-out shelves (on some models) Some shelves slide out, providing easier access to foods

stored in back. To slide out shelf, carefully pull front of shelf toward

you. To slide in shelf, push shelf in until it stops,

Ordering replacement filters

To order more water filter cartridges, call 1-800-366-PART and ask for accessory Part #4392857.

The shelves in your refrigerator are adjustable to meet your

individual storage needs.

Storing similar food items together in your refrigerator and adjusting the shelves to fit different heights of items will

make finding the exact item you want easier. It will also reduce the amount of time the refrigerator door is open,

and save energy.

IMPORTANT: Do not clean glass shelves with warm water when they are cold. Shelves may break if exposed to sudden temperature changes or impact. For your

protection tempered glass is designed to shatter into many small pebble-size pieces. This is normal.

NOTE: Glass shelves are heavy. Use special care when

removing them to avoid impact from dropping.

To remove a shelf from the metal frame:

1. Pull shelf out to the stop.

2. Tilt front of the shelf up and pull it out a little further.

3. Lift up shelf so that it moves through the slot in the frame.

Replace the shelf in the reverse order.

Shelves and shelf frames To remove a shelf/frame:

1. Tilt up front of the shelf/frame.

2. Pull shelf/frame.

To replace a shelf/frame:

1. Guide the rear shelf hooks into the slots in the shelf supports on the back refrigerator wall.

2. Tilt up front of shelf/frame.

3. Lower the front of the shelf into position.

Lste s

To slide the shelf from side to side:

1. Lift up on the front of shelf and slide to the desired

location.

2. Lower shelf to the level position. NOTE: You do not have to remove small items from the

shelf before moving it from side to side. You may need to

remove larger items.

To remove the shelf:

NOTE: The shelf is heavy and must be removed using both

hands.

1. Remove all items from the shelf.

2. Hold the back of the shelf with one hand.

3. Lift the front of the shelf with the other hand to a 45 °

angle and lower it slightly to release it from the upper channel of the track.

To replace the shelf:

NOTE: Make sure that both of the rear shelf slides are

securely in the track before letting go of the shelf. The

lateral shelf may be difficult to install if the track is placed too close to the refrigerator ceiling. Reposition the track on a lower rung until the shelf can be tilted enough to easily

slide into the track.

1. Hold the shelf at the front and tip the front at a 45 ° angle to the track.

2. Insert both of the rear shelf slides into the upper channel of the track.

3. Lower the front into place.

Dawe O©vel

To remove the drawer:

1. Slide the drawer straight out to the stop.

2. Lift the front slightly and slide it out the rest of the way.

4. Pull the shelf straight out.

To remove the shelf track:

1. Lift both sides of the track slightly.

2. Pull straight out. To replace the shelf track:

1. Guide the track hooks into the shelf support slots on the back wall.

NOTE: Make sure that both sets of track hooks are in the slots and that the slots are parallel with each other.

2. Push the track back and down securely into the shelf supports.

3. Replace the drawer by sliding it past the drawer stop.

To remove the cover:

1. Remove the drawer and the crisper.

2. Lift the front of the cover off of the supports and remove it by pulling up and out.

To replace the cover:

1. Fit the back of the cover into the notch supports on the walls of the refrigerator and lower it into place.

2. Replace the drawer and crisper.

The convertible vegetable/meat drawer can be adjusted to

properly chill meats or vegetables. Unlike most chilled meat drawer systems, the Temperature Control cools the

air inside the pan. (Most systems chill only the pan itself, which doesn't cool the air inside the pan evenly).

Chilling the air inside the pan provides more even cooling and reduces "spot" freezing. The Temperature Control can

be set to keep meats at the recommended storage

temperatures (28°F-32°F are the recommended storage temperatures from the National Livestock and Meat

Board).

To store vegetables at their optimal storage temperatures (which need to be warmer than those for meat), set the

control at the Vegetable setting, all the way to the left.

To remove the crisper:

1. Slide crisper straight out to the stop.

2. Lift the front.

3. Slide crisper out the rest of the way. Replace the crisper by sliding it back in fully past the

drawer stop.

To remove the crisper cover:

1. Remove crisper.

2. Holding glass insert firmly, grasp one side of crisper

cover and lift the other side up from the bottom.

3. Slide the glass insert out to remove.

4. Lift cover frame up and remove.

IMPORTANT: To extend freshness even more, remember

to wrap meats in airtight, moisture-proof materials before storing. Always store meat as recommended by the

National Livestock and Meat Board. See "Storing fresh

food" in the "Food Storage Guide" section for more

information.

Adjusting the control

The convertible control comes preset for you at the lowest

meat setting. Move it to the mid-setting or "colder" as

desired. To change a control setting: move the control to the right

(colder) or to the left (less cold). To store vegetables: move the control all the way to the

left to the VEG setting.

IMPORTANT: tf food starts to freeze, move the control to

the left (less cold). Remember to wait 24 hours between adjustments. Doing so gives the temperature of the food

time to change.

To replace the crisper cover:

1. Fit back of cover frame into supports on side walls of

the refrigerator.

2. Lower front of the cover frame into place.

3. Slide rear of glass insert into cover frame and lower

front into place.

some s

You can control the amount of humidity in the moisture- sealed crisper. Adjust the control to any setting between

LOW and HIGH.

• LOW (open) lets moist air out of the crisper for best storage of fruits and vegetables with skins•

• HIGH (closed) keeps moist air in the crisper for best storage of fresh, leafy vegetables•

Replace the dell drawer by sliding it back in fully past

the drawer stop.

The door rails may be removed for easier cleaning.

Snap-on Door Rails

To remove the rails:

1. Remove all items from the shelf•

2. Push in slightly on the front of the bracket while pulling out on the inside tab.

Or"SIse COv<:,l!'

In order to prevent food items from falling behind your crisper, some models have a crisper cover extension that covers the gap between the back wall and the back side of the crisper• You may want to remove the extension when cleaning.

To remove the crisper cover extension:

1. Lift up on the front of the extension•

2. Pull it off of the supports.

To replace the crisper cover extension:

1. Fit it back onto the supports on the side walls•

2. Rest the front of the extension on the crisper cover•

3. Repeat these steps for the other end of the rail.

To replace the rails:

1. Line up the ends of the brackets with the buttons on the sides of the door liner•

2. Firmly snap bracket and rail assembly onto the tabs above the shelf as shown•

Drop-in Door Rails

To remove the rails:

1. Remove all items from the shelf•

2. Pull straight up on each end of the rail.

The dell drawer provides a convenient place to store

raisins, nuts, spreads, and other small items at normal refrigerator temperatures•

To remove the dell drawer:

1. Slide the dell drawer straight out to the stop•

2. Lift the front and slide the drawer out the rest of the way.

To replace the rails:

1. Slide the shelf rail into the slots on the door•

2. Push the rail straight down until it stops•

CARING FOR YOUR

The door bins are removable for easy cleaning and adjusting.

1. To remove the bin, simply lift the bin up and pull straight out.

2. To replace the bin, slide it in above the desired support button and push down until it stops.

To remove the shelf:

1. Lift the shelf off of the supports.

2. Slide it out of the shelf support holes.

Replace shelf in the reverse order.

REFRIGERATOR

Explosion Hazard

Use nonflammable cleaner. Failure to do so can result in death, explosion,

or fire.

Both the refrigerator and freezer sections defrost

automatically. However, clean both sections about once a

month to prevent odors from building up. Wipe up spills immediately.

Energy Saving Tip:

Clean the condenser coils regularly, as described in the cleaning chart in this section. A coil cleaning brush is available for purchase. Call 1-800-366-PART and ask for

Part Number 4210463.

,y,_,_,,,,,,,, ,,, _,, ......

The freezer basket can be used to store bags of frozen fruits and vegetables that may slide off freezer shelves.

To remove the freezer basket:

1. Slide it out to the stop.

2. Lift the front and slide it out the rest of the way.

To replace the basket:

1. Position it on the slides, making sure that the wire stops are clear of the front of the slides.

2. Slide it back in all the way.

To clean your refrigerator:

• Unplug refrigerator or disconnect power.

• Remove all removable parts from inside, such as shelves, crispers, etc.

• Use a clean sponge or soft cloth and a mild detergent in warm water. Do not use abrasive or harsh cleaners.

• Hand wash, rinse, and dry all surfaces thoroughly.

• Plug in refrigerator or reconnect power.

• Additional cleaning tips are listed below:

Light behind control panel:

PART COMMENTS

Outside • Waxing external painted metal

surfaces helps provide rust protection. Do not wax plastic parts. Wax painted metal surfaces at least twice a year using appliance wax (or auto paste wax). Apply wax with a clean, soft cloth.

Inside walls

(allow freezer to warm up so

cloth won't stick)

Door liners • Do not use cleaning waxes,

and gaskets concentrated detergents, bleaches,

Plastic parts • Do not use paper towels, window

(covers and sprays, scouring cleansers or

panels) scratch or damage material.

Condenser • Remove base grille. (See the

coils "Base Grille" section.)

NOTE: Not all appliance bulbs will fit your refrigerator. Be

sure to replace the bulb with one of the same size and shape.

To help remove odors, you can wash with a mixture of warm water

and baking soda (2 tbs to 1 qt [26 g to .95 L] of water).

or cleaners containing petroleum on plastic parts.

flammable fluids. These can

• Use a vacuum with an extended attachment to clean condenser coils.

Vacuum coils when dusty or dirty. Coils may need to be cleaned as often as every other month.

• Replace base grille.

Refrigerator light bulbs

Dispenser area light (on some models):

1. Unplug refrigerator or disconnect power.

2. Reach through the dispenser area to remove the bulb.

1. Unplug refrigerator or disconnect power.

2. Reach behind the Control Panel and remove the bulb.

3. Replace the bulb with a 40-watt appliance bulb.

4. Plug in refrigerator or reconnect power.

Crisper light (on some models):

1. Unplug refrigerator or disconnect power.

2. Pull the top of the light shield forward until it snaps free and lower it until the light bulb is visible.

3. Replace the bulb with a 40-watt appliance bulb.

4. Pull the top of the light shield up over the bulb and snap

it onto the side wall supports.

5. Plug in refrigerator or reconnect power.

To remove light shield for cleaning:

1. Remove the crisper and the crisper cover.

2. Release the bottom of the shield from the lower side wall supports.

3. Pull the light shield out from above the crisper cover and wash it with warm water and a liquid detergent.

4. Rinse and dry the cover.

5. Push the light shield up over the bulb and snap it into the side wall supports.

Freezer light bulbs Light below the ice bin:

1. Unplug refrigerator or disconnect power.

2. Push in the sides of the light shield and pull down until the shield snaps free.

3. Replace the bulb with a heavy-duty 10-watt bulb, which can be purchased from your dealer.

4. Plug in refrigerator or reconnect power.

3. Replace the bulb with a 40-watt appliance bulb.

4. Replace the light shield.

5. Plug in refrigerator or reconnect power. Upper freezer light (on some models):

1. Unplug refrigerator or disconnect power.

2. Remove the light shield by grasping the top center of

the shield and pulling forward while turning it slightly to one side.

3. Replace the bulb with a 40-watt appliance bulb.

4. Replace the light shield by grasping the top center of

the shield and inserting the tabs on one end into the slotted holes in the freezer liner. Then, carefully bend

the shield at the center to insert the tabs on the other

end.

5. Plug in refrigerator or reconnect power.

If the electricity in your house goes off, call the power

company and ask how long it will be off.

1. If the power will be out for 24 hours or less, keep both

refrigerator doors closed to help foods stay cold and frozen.

2. If the power will be out for more than 24 hours:

a) Remove all frozen food and store it in a frozen food

locker.

b) Place 2 lb. (907 g) of dry ice in the freezer for every

cubic foot (28 liters) of freezer space. This will keep the food frozen for two to four days. While handling

dry ice, wear gloves to protect your hands from ice

burns.

c) If neither a food locker nor dry ice is available,

consume up or can perishable food at once.

REMEMBER: A full freezer stays cold longer than a partially filled one. A freezer full of meat stays cold longer

than a freezer full of baked goods. If you see that food contains ice crystals, it may be safely refrozen, although

the quality and flavor may be affected. If the condition of the food is poor, or if you feel it is unsafe, dispose of it.

Vacations

If you choose to leave the refrigerator on while you're

away, use these steps to prepare your refrigerator before you leave.

1. Use up any perishables and freeze other items.

2. If your refrigerator has an automatic ice maker:

• Raise ice maker arm to OFF (up) position.

• Shut off water supply to the ice maker.

3. Empty the ice bin. If you choose to turn the refrigerator off before you

leave, follow these steps.

1. Remove all food from the refrigerator.

2. If your refrigerator has an automatic ice maker:

• Turn off the water supply to the ice maker at least one day ahead of time.

• When the last load of ice drops, raise the ice maker arm to the OFF (up) position.

3. Depending on your model, turn the Thermostat Control (or Refrigerator Control, depending on the model) to

OFE See the "Setting the Controls" section.

4. Clean refrigerator, wipe it, and dry well.

5. Tape rubber or wood blocks to the tops of both doors to prop them open far enough for air to get in. This stops

odor and mold from building up.

Moving

When you are moving your refrigerator to a new home, follow these steps to prepare it for the move.

1. If your refrigerator has an automatic ice maker:

• Turn off the water supply to the ice maker at least

one day ahead of time.

• Disconnect the water line from the back of the

refrigerator.

• When the last load of ice drops, raise the ice maker

arm to the OFF (up) position.

2. Remove all food from the refrigerator and pack all frozen food in dry ice.

3. Depending on your model, turn the Thermostat Control (or Refrigerator Control, depending on the model) to

OFE See the "Setting the Controls" section.

4. Unplug the refrigerator.

5. Empty water from the defrost pan.

6. Clean, wipe, and dry thoroughly.

7. Take out all removable parts, wrap them well, and tape them together so they don't shift and rattle during the

move.

8. Depending on the model, raise the front of the refrigerator so it rolls easier OR screw in the leveling legs so they don't scrape the floor. See the "Door Closing" section.

9. Tape the doors shut and the power cord to the refrigerator cabinet.

When you get to your new home, put everything back and refer to the "Installing Your Refrigerator" section for

preparation instructions. Also, if your refrigerator has an

automatic ice maker, remember to reconnect the water supply to the refrigerator.

TROUBLESHOOTING

Try the solutions suggested here first in order to avoid the cost of an unnecessary service call.

Your refrigerator will not operate

The power supply cord is unplugged,

Firmly plug the cord into a live outlet with proper voltage.

A household fuse or circuit breaker has tripped. Replace the fuse or reset the circuit.

The refrigerator control is turned to the "OFF" position.

Refer to the "Setting the Controls" section. The refrigerator is defrosting.

Recheck to see if the refrigerator is operating in 30 minutes. Your refrigerator will regularly run an automatic defrost cycle.

The lights do not work ' ':

• The power supply cord is unplugged. Firmly plug the cord into a live outlet with proper voltage.

A light bulb is loose in the socket. Turn the refrigerator control to "OFF". Disconnect the refrigerator from the electrical supply. Gently remove the bulb and reinsert. Then reconnect the refrigerator to the electrical supply and reset the refrigerator control.

• A light bulb has burned out. Replace with an appliance bulb of the same wattage, size, and shape. See the "Changing the Light Bulbs"

section.

There is water in the defrost drain pan

• The refrigerator is defrosting. The water will evaporate. It is normal for water to drip into the defrost pan.

• It is more humid than normal. Expect that the water in the defrost pan will take longer

to evaporate. This is normal when it is hot or humid.

The motor seems to run too much

The room temperature is hotter than normal.

Expect the motor to run longer under warm conditions. At normal room temperatures, expect your motor to run

about 40% to 80% of the time. Under warmer conditions, expect it to run even more of the time.

A large amount of food has just been added to the refrigerator, Adding a large amount of food warms the refrigerator. It is normal for the motor to run longer in order to cool the refrigerator back down. See the "Food Storage Guide"

section.

• The door is opened often. Expect the motor to run longer when this occurs. In

order to conserve energy, try to get everything you need out of the refrigerator at once, keep food organized so it is easy to find, and close the door as soon as the food is

removed.

• The controls are not set correctly for the

surrounding conditions.

Refer to the "Setting the Controls" section.

• The doors are not closed completely. Push the doors firmly shut. If they will not shut all the way, see "The doors will not close completely" later in

this section.

• The condenser coils are dirty. This prevents air transfer and makes the motor work

harder. Clean the condenser coils. Refer to the "Cleaning Your Refrigerator" section.

• The door gaskets are not sealed all the way around. Contact a qualified person or a technician.

NOTE: If the problem is not due to any of the above, remember that your new refrigerator will run longer than your old one due to its high efficiency motor.

The ice maker is producing too little ice

The ice maker has just been installed. Wait 72 hours for full ice production to begin. Once your refrigerator is cooled down, the ice maker should begin producing 70-120 cubes every 24 hours.

A large amount of ice has just been removed. Allow 24 hours for ice maker to produce more ice.

The controls are not set correctly.

Refer to the "Setting the Controls" section. The water shut-off valve is not turned completely on.

Turn valve on fully. Refer to the "Connecting the Refrigerator to a Water Source" section.

There is a water filter installed on the refrigerator, This filter may be clogged or installed incorrectly.

First, check the filter installation instructionsto ensure that the filter was installed correctly and is not clogged. If

installation or clogging is not a problem, call a qualified person or a technician.

Off-taste, odor or grey color in the ice

The refrigerator seems to make too much

noise

• The sounds may be normal for your refrigerator. Refer to the "Understanding Sounds You May Hear"

section.

The ice maker is not producing ice

• The freezer temperature is not cold enough to produce ice. Wait 24 hours after ice maker hook-up for ice production. Refer to the "Setting the Controls" section.

• The ice maker arm is in the "OFF" (arm up) position. Lower arm to the "ON" (arm down) position. See the "Ice Maker Operation" section.

• The water line shut-off valve to the refrigerator is not

turned on.

Turn on the water valve. See the "Connecting the Refrigerator to a Water Source" section.

• An ice cube is jammed in the ejector arm. Remove the ice from the ejector arm with a plastic utensil. Refer to the "Ice Maker Operation" section.

• The ice maker mold has no water in it or no ice has

been produced.

Check to see if your refrigerator has been connected to your home water supply and the supply shut-off valve is turned on. Refer to the "Connecting the Refrigerator to a

Water Source" section. NOTE: If not due to any of the above, there may be a

problem with the water line. Call for service.

• The plumbing connections are new, causing discolored or off-flavored ice.

Discard the first few batches of ice. The ice cubes have been stored for too long.

Throw old ice away and make a new supply.

Food in the freezer or refrigerator has not been wrapped properly.

Refer to the "Food Storage Guide" section. Freezer and ice bin need to be cleaned.

See the "Cleaning Your Refrigerator" section. Water contains minerals (such as sulfur).

A filter may need to be installed to remove the minerals.

There is a water filter installed on the refrigerator, Grey or dark discoloration in ice indicates that the water filtration system needs additional flushing.

Run additional water through the water dispenser to flush the water filtration system more thoroughly (at least 2-3 gallons or 6-7 minutes initially). Discard discolored

ice.

The ice dispenser will not operate properly

• The freezer door is not closed completely, Push the door firmly shut. If it will not shut all the way, see "The doors will not close completely" later in this

section.

• The ice bin is not installed correctly. Push the ice bin in all the way. If the ice bin does not go in all the way, it may not be put in straight. Pull it out and try again.

• The wrong ice has been added to the bin. Use only cubes produced by the current ice maker. If

other cubes have been added, remove all cubes and check to see that none have become stuck in the

delivery chute.

• The ice has frozen in the ice bin. Shake the ice bin to separate cubes. If cubes do net

separate, empty bin and wait 24 hours for ice to restock.

• The ice has melted around the auger (metal spiral) in the ice bucket.

Dump the ice cubes and clean the ice bucket completely. Allow 24 hours for the ice maker to restock. Do not try to remove the melted ice with a sharp object. You could damage the ice bucket.

• Ice is stuck in the delivery chute. Clear the icefrom the delivery chute with a plastic utensil. Do not use anything sharp to remove the ice. You could cause damage.

• There is no ice in the bucket. See "The ice maker is not producing ice" earlier in this

section.

• The dispenser arm has been held in too long. Release dispenser arm. Ice will stop dispensing when the arm is held in too long. Wait three minutes for dispenser motor to reset before using again. (For future use, take large amounts of ice directly from the ice maker so that the dispenser arm is not held in too long.)

The water dispenser will not operate properly

• The freezer door is not closed completely. Push the door firmly shut. If it will not shut all the way, see "The doors will not close completely" later in this

section.

• The water tank has not filled. The water tank needs to be filled the first time itis used. Depress the water dispenser bar with a large container

until you draw two or three quarts (1.9 to 2.8 L) of water. Discard water. (Refer to the "Water and Ice Dispensers" section for further instructionson filling the water tank.)

• The water shut-off valve is not turned on or the water line is not connected at the source.

Check to be sure the water shut-off valve isturned on and the water source is connected to the refrigerator.

Refer to the "Connecting the Refrigerator to a Water Source" section for directions.

Water or ice is leaking from the dispenser

The glass is not being held under the ice dispenser long enough, causing the ice to spill.

Hold the container under the ice chute for two to three seconds after releasing the dispenser lever. A small

amount of ice may dispense after the lever is released.

The glass is not being held under the water dispenser long enough, causing water to drip.

Hold the container under the water dispenser two to three seconds after releasing the dispenser lever. Water may continue to dispense during this time.

An ice cube is stuck in the chute and holding the trap door open.

Remove the cube.

There is a water filter installed on the refrigerator. The water filtration system may have air in the lines, causing water to drip.

Additional flushing may help clear air from the lines. Normal dispenser use should flush air from the lines

within 24-72 hours.

--ZHHHHJ.J_,_`_`_H_`_`_`_HHHHHHHHHHHHHHHHHHHHHHH_Thedispenser water is not cool enough

• The refrigerator has been newly installed. Allow 24 hours for the tank to cool completely.

• A large amount of water has been recently

dispensed.

Allow 24 hours for the tank to cool completely.

• No water has been recently dispensed. The first glass of water may not be cool. Discard the first glass of water,

The divider between the two compartments is

warm

• The warmth is probably due to normal operation of the automatic exterior moisture control. If still concerned, call for service.

• The water shut-off valve is clogged or incorrectly

installed.

Refer to the "Connecting the Refrigerator to a Water Source" section. If clogging or installation is not a problem, call for service or a contact a plumber.

• There is a kink in the home water source line. If you find or suspect a kink in the water line, call for

service.

• There is a water filter installed on the refrigerator. This filter may be clogged or incorrectly installed.

First, check the filter installation instructions to ensure that the filter was installed correctly and is not clogged. If

installation or clogging is not a problem, call for service.

Temperature is too warm The doors will not close completely

• The air vents are blocked in either compartment.

This prevents the movement of cold air from the

freezer to the refrigerator. Remove any objects from in front of the air vents. Refer to the "Ensuring Proper Air Circulation" section for the

location of air vents.

• The door(s) are opened often. Be aware that the refrigerator will warm when this occurs. In order to keep the refrigerator cool, try to get everything you need out of the refrigerator at once, keep food organized so it is easy to find, and close the door

as soon as the food is removed.

• A large amount of food has just been added to the refrigerator or freezer. Adding a large amount of food warms the refrigerator. It can take several hours for the refrigerator to return to the normal temperature.

• The controls are not set correctly for the surroinding

conditions.

Refer to the "Setting the Controls" section.

There is interior moisture build-up

• The air vents are blocked in the refrigerator. Remove any objects from in front of the air vents. Refer to the "Ensuring Proper Air Circulation" section for the

location of air vents.

• The door is opened often. To avoid humidity build-up, try to get everything you need out of the refrigerator at once, keep food organized so it is easy to find, and close the door as soon as the food is removed. (When the door is opened, humidity from the room air enters the refrigerator. The more often the door is opened, the faster humidity builds up, especially when the room itself is very humid.)

• The room is humid. It is normal for moisture to build up inside the refrigerator

when the room air is humid.

• The food is not packaged correctly. Check that all food is securely wrapped. If necessary, repackage food according to the guidelines in the "Food Storage Guide" section. Wipe off damp food containers before placing in the refrigerator.

• The controls are not set correctly for the

surrounding conditions.

Refer to the "Setting the Controls" section.

• A self-defrost cycle was completed. It is normal for droplets to form on the back wall after the refrigerator self-defrosts.

Food packages are blocking the door open. Rearrange containers so that they fit more tightly and take up less space.

The ice bin is out of position. Push the ice bin in all the way.

The pans, shelves, bins, or baskets are out of position.

Put the crisper cover and all pans, shelves, bins, and baskets back into their correct position. See the "Crisper and Crisper Cover" section for more information.

The gaskets are sticking.

Clean gaskets and then apply paraffin wax according to the directions in the "Cleaning Your Refrigerator"

section. The refrigerator wobbles or seems unstable.

Level the refrigerator. Refer to the "Door Closing and Alignment" section.

The doors were removed during product installation and not properly replaced.

Remove and replace the doors according to the "Removing the Doors" section, or call a qualified service

technician.

The doors are difficult to open

• The gaskets are dirty or sticky. Clean gaskets according to the directions in the "Cleaning Your Refrigerator" section.The gaskets are dirty or sticky.

Water flow from the dispenser decreases

noticeably

• There is a water filter installed on the refrigerator. This filter may be full or incorrectly installed.

Remove the water filter cartridge (see the "Water Filtration System" section.) Operate the dispenser. If the water flow increases noticeably, your filter is full and needs to be replaced.

SEARS

MAINTENANCE

AGREEMENT

"We Service What We Sell" is our assurance to you that you can depend on Sears for service. Your Kenmore

appliance has added value when you consider that Sears

has service units nationwide, staffed with professional

technicians trained on all appliances Sears sells. They

have the knowledge and skills, tools, parts and equipment to ensure our pledge to you that "We Service What We Sell."

Sears Maintenance Agreement

Maintain the value of your purchase with a Sears

Maintenance Agreement. Kenmore appliances are designed, manufactured, and tested for years of

dependable operation. Yet any home appliance may

require service from time to time. The Sears Maintenance Agreement offers you an outstanding service program for

your product.

The Sears Maintenance Agreement

• Is your way to buy tomorrow's service at today's prices.

• Eliminates repair bills resulting from normal use.

• Allows for as many service calls as you need.

• Provides an annual Preventive Maintenance Check

at your request to keep your Kenmore Appliance in

proper running condition.

For more information, call 1-800-827-6655.

WATER FILTER CERTIFICATIONS

State of California

Department of Health Services

Water Treatment Device

Certificate Number

98- 1343

Date Issued: June 9, 1998

Trademark/Model Designation

The water treatment Section 116830 of tht Health _d Safety

Microbiological Contaminants and Turbidity

None

_inants

Renlacement Elements

pursuant to

• . , ,: _:_; d_-%Rated Service CapacRy. 5_g_aHons _._ _,

Do not use with water that is

disinfection before or after the system.

0.5 gpm

quality, without adequate

Product Data Sheet

Water Filtration System Model NLC-250

(_ This product has been tested and certified by NSF International underANSI/NSF Standard 42

for Taste, Odor and Chlorine reduction (Classl) and Particulate reduction (Class ]) and under

Standard 53 for Cyst, Turbidity, and Lead reduction.

Specifications: Lead, Particulate (Class l), Cyst, Turbidity and Taste/Odor/Chlorine reduction (Class ])

259 Gallons (946 Liters)

Service Flow Rate 0.5 GPM (1.89 L/min) @ 60 psi

Substance

Reduction Average Maximum Average Minimum % Average% NSF Test

Aesthetic Effects Influent Effluent Effluent Reduction Reduction Requirement

Chlorine 1.9 mg/L N/A 0.04 mg/L N/A 97.9% minimum 75% reduction (Class ]) Particulate 610,000/mLt N/A 154/mL N/A 99.97% minimum 85% reduction (Class ])

Substance Reduction U.S. EPA Average Maximum Average Minimum % Average %

Health Effects MCL Influent Effluent Effluent Reduction Reduction NSF Test Requirement Cyst 99.95% 89,250/mU 6/mL 2.3/mL 99.993% 99.997% minimum99.95% reduction

Turbidity 0.5 NTU 29 NTU 0.12 NTU 0.09 NTU 99.59% 99.69% maximumeffluent 1.0NTU Lead@pH6.5 0.015mg/L 0.16mg/U t 0.001mg/L 0.001mg/L 99.4% 99.4% maximum effluent0.015 mg/L

Lead@pH8.5 0.015mg/L 0.16mg/L tt 0.002mg/L 0.001mg/L 98.8% 99.4% maximum effluent0.015 mg/L

t Test requirement is at least 10,000 particles/mL of AC Fine Test Dust. tt Test requirement is 0.15 mg/L _+10%.

These contaminants are not necessarily in your water supply. Performance may vary based on local water conditions.

Application Guidelines/

Water Supply Parameters

® NSF is a registered trademark of NSF International

Water Supply City or Well Water Pressure 30-120 psi (207-827 kPa)

Water Temperature 33°-100°F (0.6°-37.8°C)

• It is essential that operational, maintenance, and filter replacement requirements be carried

out for this product to perform as advertised.

• Change cartridge at least every 6-9 months.

Use replacement cartridge part #NLC-250 or #4392922. Suggested retail price of $39.95

U.S.A./S49.95 Canada.

•The product is for cold water use only.

• Do not use with water that is microbiologically

unsafe or of unknown quality without adequate disinfection before or after the system. Systems

certified for cyst reduction may be used on disinfected water that may contain filterable

cysts.

+ 67 hidden pages