Kenmore 10653799202, 10653799201, 10653799200, 10653794202, 10653794201 Owner’s Manual

E L ! T E

TM

Side by Side Refrigerator

Refrigerador de dos puertas
R_fri _rateur c6te & c6te

2220693 Sears Canada, Inc., Toronto, Ontario, Canada MSB 2B8 www.sears.ca

Sears Roebuck and Co., Hoffman Estates, IL 60179 U.S.A. www.sears.com

TABLE OF CONTENTS

WARRANTY

WARRANTY ..................................................................................... 2

REFRIGERATOR SAFETY .............................................................. 3

REFRIGERATOR INSTALLATION ................................................. 4

Unpacking .................................................................................... 4

Location Requirements ................................................................ 4

Electrical Requirements ................................................................ 5

Base Grille .................................................................................... 5

Door Removal ............................................................................... 6

Door Closing and Alignment ........................................................ 8

Water Supply Connection ............................................................ 8

Water System Preparation ........................................................... 9

Normal Sounds ............................................................................. 9

REFRIGERATOR USE .................................................................... 9

Ensuring Proper Air Circulation .................................................... 9

Using the Controls ..................................................................... 10

Water and Ice Dispensers ......................................................... 12

Water Filtration System ............................................................. 13

Ice Maker and Storage Bin/Bucket ........................................... 14

REFRIGERATOR FEATURES ..................................................... 14

Refrigerator Shelves .................................................................. 14

Flip-up Shelf .............................................................................. 15

Adjustable Flip-up Shelf ............................................................ 15

Dell Drawer ................................................................................ 15

Convertible Vegetable/Meat Drawer, Crisper and Covers ....... 15

Convertible Vegetable/Meat Drawer Temperature Control ...... 16

Crisper Humidity Control ........................................................... 16

Wine or Can/Bottle Rack ........................................................... 16

Utility Bin .................................................................................... 16

FREEZER FEATURES ................................................................. 16

Freezer Shelf .............................................................................. 16

Freezer Basket or Bin ................................................................ 17

DOOR FEATURES ....................................................................... 17

Door Rails .................................................................................. 17

Can Racks and Door Bins ......................................................... 17

REFRIGERATOR CARE ............................................................... 17

Cleaning ..................................................................................... 17

Changing the Light Bulbs .......................................................... 18

Power Interruptions ................................................................... 19

Vacation and Moving Care ........................................................ 19

TROUBLESHOOTING .................................................................. 20

SERVICE ....................................................................................... 23

In the U.S.A ................................................................................ 23

In Canada .................................................................................. 23

Accessories ............................................................................... 23

WATER FILTER CERTIFICATIONS ............................................ 24

PERFORMANCE DATA SHEETS ............................................... 25

ONE-YEAR FULL WARRANTY ON REFRIGERATOR

For one year from the date of purchase, when this refrigerator is
operated and maintained according to instructions attached to or
furnished with the product, Sears will repair this refrigerator, free
of charge, if defective in material or workmanship.

FIVE-YEAR FULL WARRANTY ON SEALED REFRIGERATION
SYSTEM

For five years from the date of purchase, when this refrigerator is
operated and maintained according to owner's instructions
attached to or furnished with the product, Sears will repair the
sealed system (consisting of refrigeration, connecting tubing, and
compressor), free of charge, if defective in materials or
workmanship.

The above warranty coverage applies only to refrigerators which
are used for storage of food for private household purposes and
excludes original and replacement Kenmore Filtered Ice & Water
filter cartridges (if equipped with the filter system). Original and
replacement cartridges are warranted for 30 days, parts only,
against defects in material or workmanship.

WARRANTY SERVICE IS AVAILABLE BY CONTACTING THE

NEAREST SEARS SERVICE CENTER IN THE UNITED STATES
OR CANADA.

This warranty applies only while this product is in use in the

United States or Canada. This warranty gives you specific
legal rights, and you may also have other rights which vary
from state to state or province to province.

Warranty terms may vary in Canada. Contact your local Sears
Service Center for complete details.

Sears, Roebuck and Co.

Dept. 817WA, Hoffman Estates, IL 60179

Sears Canada, Inc., Toronto, Ontario, Canada M5B 2B8

Product Record

In the space below, record your complete model number, serial

number, and purchase date. You can find this information on the
model and serial number label located on the inside wall of the

refrigerator compartment.

Have this information available to help you obtain assistance or
service more quickly whenever you contact Sears concerning
your refrigerator.

Model number 106.

Serial number

Purchase date

Save these instructions and your sales receipt for future
reference.

2

REFRIGERATOR SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all
safety messages.

This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word "DANGER" or

This is the safety alert symbol.
"WARNING." These words mean:

You can be killed or seriously injured if you don't

immediately follow instructions.

You can be killed or seriously injured if you don't
follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you
what can happen if the instructions are not followed.

IM PORTANT SAFETY INSTRUCTIONS

WARN IN G: To reduce the risk of fire, electric shock, or injury when using your refrigerator, follow these basic

precautions:

Use nonflammable cleaner.

n Plug into a grounded 3 prong outlet.
n Do not remove ground prong.
n Do not use an adapter.

n Do not use an extension cord.
n Disconnect power before servicing.

n Replace all panels before operating.
n Remove doors from your old refrigerator.

n

n Keep flammable materials and vapors, such as

gasoline, away from refrigerator.

n Use two or more people to move and install

refrigerator.

n Disconnect power before installing ice maker (on

ice maker kit ready models only).

n Use a sturdy glass when dispensing ice or water

(on some models).

SAVE THESE INSTRUCTIONS

Proper Disposal of

Your Old Refrigerator

IMPORTANT: Child entrapment and suffocation are not problems

of the past. Junked or abandoned refrigerators are still dangerous

- even if they will sit for "just a few days." If you are getting rid of
your old refrigerator, please follow these instructions to help

prevent accidents.

Before you throw away your old refrigerator or freezer:

n Take off the doors.
n Leave the shelves in place so that children may not easily

climb inside.

REFRIGERATOR

INSTALLATION

Removing packaging materials

• Remove tape and glue residue from surfaces before turning
on the refrigerator. Rub a small amount of liquid dish soap
over the adhesive with your fingers. Wipe with warm water

and dry.
Do not use sharp instruments, rubbing alcohol, flammable

fluids, or abrasive cleaners to remove tape or glue. These
products can damage the surface of your refrigerator. For
more information, see the "Refrigerator Safety" section.

When Moving Your Refrigerator:

Your refrigerator is heavy. When moving the refrigerator
for cleaning or service, be sure to protect the floor.
Always pull the refrigerator straight out when moving it.

Do not wiggle or "walk" the refrigerator when trying to move
it, as floor damage could occur.

Cleaning before use

After you remove all of the packaging materials, clean the inside
of your refrigerator before using it. See the cleaning instructions
in the "Refrigerator Care" section.

Important information to know about glass shelves

and covers:

Do not clean glass shelves or covers with warm water when
they are cold. Shelves and covers may break if exposed to
sudden temperature changes or impact, such as bumping.

For your protection, tempered glass is designed to shatter

into many small, pebble-size pieces. This is normal. Glass
shelves and covers are heavy. Use special care when re-
moving them to avoid impact from dropping.

Explosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from refrigerator.

Failure to do so can result in death, explosion,
or fire.

To ensure proper ventilation for your refrigerator, allow for _/2in.
(1.25 cm) space on each side and at the top. When installing your
refrigerator next to a fixed wall, leave 2 in. 15.08 cm) minimum on
each side (depending on your model) to allow for the door to
swing open. If your refrigerator has an ice maker, allow extra
space at the back for the water line connections.

NOTE: Do not install the refrigerator near an oven, radiator, or

other heat source, nor in a location where the temperature will fall

below 55°F (13°C).

JL

J

/

/2" 1.25 cm (

/

i

2" 15.08 cm) /

/

/

,m

4

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.

Do not use an extension cord.
Failure to follow these instructions can result in

death, fire, or electrical shock.

Before you move your refrigerator into its final location, it is
important to make sure you have the proper electrical

connection:

Recommended grounding method

A 115 Volt, 60 Hz., AC only 15 or 20 ampere fused, grounded
electrical supply is required. It is recommended that a separate
circuit serving only your refrigerator be provided. Use an outlet
that cannot be turned off by a switch. Do not use an

extension cord.
NOTE: Before performing any type of installation, cleaning, or

removing a light bulb, turn the control (Thermostat, Refrigerator
or Freezer Control depending on the model) to OFF and then
disconnect the refrigerator from the electrical source. When you
are finished, reconnect the refrigerator to the electrical source
and reset the control (Thermostat, Refrigerator or Freezer Control
depending on the model) to the desired setting.

To remove the base grille:

1. Open both refrigerator doors.

2. Place hands along the ends of the grille, with your thumbs
along the top. Push in with your thumbs and pull up on the

bottom.

NOTE: Be sure to refasten the Tech Sheet behind the base grille

after cleaning.

To replace the base grille:

1. Open the doors.

2. Line up the grille support tabs with the metal clips,

3, Push the grille firmly to snap it into place.

TOOLS NEEDED: 1/4in., 1/2in., and 5/16in. hex-head socket wrenches, a flat-head screwdriver and a Phillips screwdriver.
IMPORTANT: Before you begin, turn the refrigerator control OFF,unplug refrigerator or disconnect power. Remove food and any

adjustable door or utility bins from doors.

Electrical Shock Hazard

Disconnect power before removing doors.
Reconnect both ground wires before operating,

Failure to do so can result in death or electrical shock.

Top Left Hinge

1. Do Not Remove Screw

Water Dispenser
Tubing Connection

1

1. Red Outer Ring

Door Removal

Top Right Hinge

t. Do Not Remove Screw

Handle Removal
(Optional)

Base Grille

Bottom Hinge

1. Do Not Remove Screw

6

NOTE: It may only be necessary to remove either the door handle

or the doors to get your product through the doorway of your
residence. Measure the door opening to determine whether to
remove the refrigerator handles or the doors.

Handle Removal (optional)

1. Apply firm pressure with your hand on the face of trim. Slide

top trim up and bottom trim down away from handle. Lift trim
pieces off shoulder screws (see Graphic 1).

2. Remove handle screws and handles.

3. Move refrigerator into place. Replace handles as shown (see
Graphic 1).

Door Removal

Door and Hinge Replacement

1. Replace both bottom hinges, if removed. Tighten screws.

2. Assistance may be needed to feed the water line through the
bottom hinge while reinstalling the freezer door. Carefully feed

the dispenser tubing through the bottom left hinge before
replacing the door on the hinge.

NOTE: Provide additional support for the doors while the top
hinges are being replaced. Do not depend on the door magnets

to hold the doors in place while you are working.

3. Reconnect water dispenser tubing by pushing tubing into

fitting until it stops and black mark touches face of fitting (see
Graphic 3). On some models, replace tubing in hose clip.

4. Align and replace the top left hinge as shown (see Graphic 4).

Tighten screws.

Electrical Shock Hazard

Disconnect power before removing doors.
Failure to do so can result in death or

electrical shock.

1. Unplug refrigerator or disconnect power.

2. Open both refrigerator doors. Remove the base grille by
pulling up on the bottom outside corners (see Graphic 2).

3. Close both doors and keep them closed until you are ready to
lift them free from the cabinet.

4. If you have a dispenser (ice or water), disconnect the water
dispenser tubing located behind the base grille on the freezer
door side (see Graphic 3).

• Press red outer ring against the face of fitting and pull the

dispenser tubing free.

• On some models, remove tubing from hose clip.

5. Remove top left hinge screw and cover as shown (see
Graphic 4).

6. Disconnect wiring plug and both ground wires from ground
wire screw (on some models) as shown (see Graphic 4).

7. Remove remaining left hinge screws and hinge as shown (see
Graphic 4). Do not remove screw 1.

8. Carefully lift freezer door straight up off bottom hinge (see
Graphic 5). The water dispenser tubing remains attached to

the freezer door and pulls through the bottom le_ hinge.
Make sure you protect the dispenser tubing from damage.

9. Remove top right hinge cover and screws as shown (see
Graphic 6). Do not remove screw 1.

10. Lift the refrigerator door straight up off bottom hinge.

11. It may not be necessary to remove the bottom hinge to move
the refrigerator through a doorway. Both bottom hinges have

similar construction.

• Disassemble the hinges as shown (see Graphic 7). Do not

remove screw 1.

Electrical Shock Hazard

Reconnect both ground wires.

Failure to do so can result in death or
electrical shock.

Style 1

• Reconnect both ground wires.

• Reconnect wiring plug.

Style 1

Style 2

• Reconnect wiring plug.

5. Replace left hinge cover and screws.

6. Replace the refrigerator door by carefully lifting the door onto
the bottom right hinge.

7. Align and replace the top right hinge as shown (see
Graphic 6). Tighten screws.

8. Replace hinge cover and screws. Tighten screws.

9. Plug into a grounded 3 prong outlet.

Door Closing

1. Move the refrigerator into its final position.

2. Place a level inside the refrigerator at the back of the top shelf
(see Graphic 8).

3. Locate the leveling screws behind the base grille of the
refrigerator on either side.

4. Use a hex-head socket wrench to adjust the rear roller
leveling screws until the refrigerator is level. Turn the rear
roller leveling screw to the right to raise that side of the
refrigerator or turn the leveling screw to the left to lower that
side (see Graphic 9). Make sure refrigerator is level before
proceeding.

5. Check the door alignment after leveling the refrigerator.

3.

Locate a V2in. to 1V4in. (1.25 cm to 3.18 cm) vertical COLD

water pipe near the refrigerator.

NOTE: Horizontal pipe will work, but drill on the top side of
the pipe, not the bottom. This will help keep water away from
the drill and normal sediment from collecting in the valve.

4.

Determine the length of copper tubing you need. Measure
from the connection on the lower left rear of refrigerator to the
water pipe. Add 7 ft. (2.1 m) to allow for cleaning. Use V4in.
(6.35 mm) O.D. (outside diameter) copper tubing. Be sure

both ends of copper tubing are cut square.

5.

Using a grounded drill, drill a V4in. hole in the cold water pipe
you have selected.

2

7. ...... .........,3

Door Alignment

If the doors are uneven after leveling the product (see
Graphic 10), follow the steps below.

1. Use a hex-head socket wrench to adjust the front roller
leveling screws until the doors are even. Turn the front roller
leveling screw to the right to raise that side of the refrigerator
or turn the leveling screw to the left to lower that side (see
Graphic 11).

NOTE: Open and close both the refrigerator and freezer doors
after each adjustment to check the door alignment.

2. Open the doors and replace the base grille. Line up the grille
support tabs with the metal clips. Push the grille firmly to
snap it into place.

NOTE: Be sure to refasten the Tech Sheet behind the base grille.

Read all directions carefully before you begin.
IMPORTANT:

• If you turn the refrigerator on before the water line is
connected, turn the ice maker QFK

• All installations must meet local plumbing code requirements.

• Use copper tubing and check for leaks. Install copper tubing
only in areas where temperatures will remain above freezing.

Tools required: Standard screwdriver, 7/_6in. and _/2in. open-end
wrenches or two adjustable wrenches, V4in. nut driver and drill
bit, hand drill or electric drill (properly grounded).

NOTE: Your refrigerator dealer has a kit available with a _/4in.
(6.35 mm) saddle-type shutoff valve, a union, and copper tubing.
Before purchasing, make sure a saddle-type valve complies with
your local plumbing codes. Do not use a piercing-type or SA6in.

(4.76 mm) saddle valve which reduces water flow and clogs more
easily.

Cold water supply

Connect the ice maker to a cold water line with water pressure
between 30 and 120 psi. If you have questions about your water
pressure, call your utility company.

Connecting to Water Line

1. Unplug refrigerator or disconnect power.

2. Turn OFF main water supply. Turn ON nearest faucet long
enough to clear line of water.

1 Cold Water Pipe 5 CompressionSleeve

2 Pipe Clamp 6 Shutoff Valve
3 Copper Tubing 7 PackingNut

4 CompressionNut

6. Fasten the shutoff valve to the cold water pipe with the pipe
clamp. Be sure the outlet end is solidly inthe _/4in. drilled hole

in the water pipe and that the washer is under the pipe clamp.
Tighten the packing nut. Tighten the pipe clamp screws
carefully and evenly so washer makes a watertight seal. Do

not overtighten or you may crush the copper tubing.

7. Slip the compression sleeve and compression nut on the
copper tubing as shown. Insert the end of the tubing into the
outlet end squarely as far as it will go. Screw compression nut
onto outlet end with adjustable wrench. Do not overtighten.

8. Place the free end of the tubing in a container or sink, and
turn ON the main water supply. Flush the tubing until water is

clear. Turn OFF the shutoff valve on the water pipe. Coil the
copper tubing.

Connecting to Refrigerator

1. Attach the copper tube to the valve inlet using a compression
nut and sleeve as shown. Tighten the compression nut. Do

not overtighten. Use the tube clamp on the back of the

refrigerator to secure the tubing to the refrigerator as shown.
This will help prevent damage to the tubing when the
refrigerator is pushed back against the wall.

2. Turn shutoff valve ON.

3.

Check for leaks. Tighten any connections (including
connections at the valve) or nuts that leak.

............................. 1

............... 2

IIIIIIIIIIIIIIIII

1. Tube Clamp

2. Copper Tubing

4. The ice maker is equipped with a built-in water strainer. If
your water conditions require a second water strainer, install

it in the _/4in. (6.35 mm) water line at either tube connection.

Obtain a water strainer from your nearest appliance dealer.

5. Plug in refrigerator or reconnect power.

3. Compression Nut

4. Valve Inlet

8

Please read before using the water system.
Immediately after installation, follow the steps below to make

sure that the water system is properly cleaned.

1. Open the freezer door and turn off the ice maker. Move the
switch to the OFF (right) setting as shown. The ON/OFF
switch is located on the top right side of the freezer
compartment.

You may hear the evaporator fan motor circulating air through
the refrigerator and freezer compartments. The fan speed
may increase as you open the doors or add warm food.

Rattling noises may come from the flow of refrigerant, the

water line, or items stored on top of the refrigerator.
Water dripping on the defrost heater during a defrost cycle

may cause a sizzling sound.
As each cycle ends, you may hear a gurgling sound due to

the refrigerant flowing in your refrigerator.
Contraction and expansion of the inside walls may cause a

popping noise.

You may hear air being forced over the condenser by the
condenser fan.

• You may hear water running into the drain pan during the
defrost cycle.

NOTES:

• If your model has a base grille filter system, make sure the
base grille filter is properly installed and the cap is in the
horizontal position.

• Do not use with water that is microbiologically unsafe or

of unknown quality without adequate disinfection before
or after the system.

2. Use a sturdy container to depress the water dispenser bar

until the water begins to flow. Flush the water system by
dispensing and discarding 2 to 3 gal. (8 to 12 L) of water.
Cleaning the system will take approximately 6 to 7 minutes
and will help clear air from the line. Additional flushing may be
required in some households.

NOTE: As air is cleared from the system, water may spurt out
of the dispenser.

3. Open the freezer door and turn on the ice maker by moving
the switch to the ON (left) setting. Please refer to the "Ice
Maker and Storage Bin/Bucket" section for further
instructions on the operation of your ice maker.

• Allow 24 hours to produce the first batch of ice. Discard

the first three batches of ice produced.

Your new refrigerator may make sounds that your old one didn't
make. Because the sounds are new to you, you might be

concerned about them. Most of the new sounds are normal. Hard
surfaces, such as the floor, walls, and cabinets, can make the
sounds seem louder. The following describes the kinds of sounds

and what may be making them.

• If your product is equipped with an ice maker, you will hear a
buzzing sound when the water valve opens to fill the ice
maker for each cycle.

• Your refrigerator is designed to run more efficiently to keep
your food items at the desired temperatures and to minimize
energy usage. The high efficiency compressor and fans may
cause your refrigerator to run longer than your old one. You
may also hear a pulsating or high-pitched sound from the
compressor or fans adjusting to optimize performance.

REFRIGERATOR USE

In order to ensure proper temperatures, you need to permit air to

flow between the two sections. Cold air enters the bottom of the
freezer section and moves up. It then enters the refrigerator

section through the top vent. Air then returns to the freezer as
shown.

f

Do not block any of these vents with food such as soda, cereal,
bread, etc. If the vents are blocked, airflow will be prevented and

the temperature controls will not function properly.

IMPORTANT: Because air circulates between both sections, any

odors formed in one section will transfer to the other. You must
thoroughly clean both sections to eliminate odors. To prevent
odor transfer from food, wrap or cover foods tightly.

YourmodelmayhaveStyle1orStyle2controls.

IMPORTANT (Both Styles):

• The Refrigerator Control adjusts the refrigerator compartment

temperature. The Freezer Control adjusts the freezer
compartment temperature.

Wait 24 hours after you turn on the refrigerator before you put
food into it. ]f you add food before the refrigerator has cooled
completely, your food may spoil. Adjusting the Refrigerator
and Freezer Controls to a lower (colder) setting will not cool
the compartments any faster.

If the temperature is too warm or too cold in the refrigerator or
freezer, first check the air vents to be sure they are not
blocked, before adjusting the controls.

The preset settings should be correct for normal household
usage. The controls are set correctly when milk or juice is as
cold as you like and when ice cream is firm.

Style 1: Electronic Controls (on some models)

For your convenience, your controls are preset at the factory.

When installing your refrigerator, make sure that the controls are
still preset to the "mid-settings" as shown.

FREEZI_ REFPJOERATOR

CONDITION: SETTING

ADJUSTMENT:

REFRIGERATOR too cold REFRIGERATOR Control

one setting lower

REFRIGERATOR too warm REFRIGERATOR Control

- High use or room very warm one setting higher
FREEZER too cold FREEZER Control one

setting lower

FREEZER too warm/too little ice FREEZER Control one

- High use or heavy ice usage setting higher

Additional Electronic Control Panel Features

Additional features are located on the control panel at the top of
the refrigerator compartment.

Water Filter Indicator Light and Reset

NOTE: Do not use with water that is microbiologically unsafe

or of unknown quality without adequate disinfection before
or after the system.

The water filter display will help you know when to change your
water filter cartridge. To change your filter, see the "Changing a

base grille water filter cartridge" section.

INDICATOR: STATUS:

0000000 0000000

_LDER _W _WER _W

l||_lil ?l|_lil

To turn on refrigerator:

• Press and hold ON/OFF for 2 seconds. The indicator lights
show the current temperature control settings.

NOTE: Settings to the left of the mid-setting make the
temperature colder. Settings to the right of the mid-setting
make the temperature less cold.

Adjusting Electronic Controls

NOTE: Wait at least 24 hours between adjustments. Re-check
the temperatures before other adjustments are made.

If you need to adjust temperatures:

• Press the freezer or refrigerator arrow to move the indicator
light to the right, one setting at a time. Continue moving the
indicator light until it is at the desired setting.

1 z a@s i 7 [

i oo

NOTE: With each press of the arrow, you will hear a beep as
the light moves to the next setting. The indicator light moves
to a setting of "7" and then returns to the setting of "1".

GOOD (green) New filter installed

ORDER (yellow) Order filter, 10% filter life remains

REPLACE (red) OR Replace water filter

when water flow
decreases

• After changing the water filter cartridge, reset the water filter
indicator by pressing and holding RESET for 2 seconds. The

status light will change from REPLACE (red) to GOOD (green)
when the filter indicator is reset.

WA_R FILER

Accelerated Ice Production

This feature assists with temporary periods of heavy ice use by

increasing ice production over a 24-hour period.

• Press the accelerated ice production touch pad to set the

freezer temperature to -10°F (-23°C). The refrigerator
temperature will not change. The accelerated ice setting will

remain on for 24 hours unless manually turned off.

If increased ice production is desired at all times, set the
Freezer Control to a colder number. Adjusting the freezer to a

colder temperature may make some foods, such as ice
cream, harder.

10

_ZHHJ_._,_E_.,,_,_ The water filter display will help you know when it is time to

Style 2: Digital Controls (on some models) change your filter. To change the filter, see the "Base Grille Water

Filtration and Monitoring System" section.
For your convenience, your controls are preset at the factory.
When installing your refrigerator, make sure that the controls are

INDICATOR: STATUS:

still preset to the "mid-settings" as shown. The digital control
panel is located at the top of the refrigerator compartment and

99 percent New filter installed

enables you to view the temperature control set points.
NOTE: The factory recommended set points are 0°F (-18°C) for

10 percent Order replacement filter
the freezer and 37°F (3°C) for the refrigerator.
To turn refrigerator on and view set points:

• Press and hold ON/OFF for 2 seconds.

Cow FREEZER REFRI6ERATOR COLD

COLDER COLDER

To view the Celsius temperatures:

• Press the °C SELECT touch pad. The indicator will light up.

=C

SELECT

0 percent OR flow decreases Replace filter

• After replacing the water filter, press RESET and hold for 2
seconds to change the the water filter display to 99 percent.

WATERFILTER

PERCENTREMAINING

GrecerySavor TM

The GrocerySavor r_feature assists with periods of high
refrigerator use, full grocery loads, or temporarily warm room
temperatures.

NOTE: If the freezer temperature is below zero, the indicator light
next to the freezer display will light up.

• Press GrocerySavo¢ Mto set the temperatures to

-10°F (-23°C) for the freezer and 34°F (1°C) for the
refrigerator. The GrocerySavor r_indicator light will remain on

Adjusting Digital Controls (on some models)

for 24 hours unless manually turned off.

To adjust set point temperatures:

• Press the refrigerator or freezer up or down arrow until the
desired temperature is reached.

REFRIGERATOR COL#

COLDER

NOTE: Wait at least 24 hours between adjustments and then
re-check the temperatures before other adjustments are

made.

• The set point range for the freezer is -5°F to 5°F (-21°C to

-15°C) and 33°F to 41°F (1°C to 5°C) for the refrigerator.

CONDITION/REASON: TEMPERATURE

ADJUSTMENT:

REFRIGERATOR too cold REFRIGERATOR

Control 1° higher

REFRIGERATOR too warm REFRIGERATOR

- High use or room very warm Control 1° lower
FREEZER too cold FREEZER Control 1°

higher

FREEZER too warm/too little ice - FREEZER Control 1°
High use or heavy ice use lower

NOTE: The temperature display will not change. After 24
hours, the refrigerator returns to the previous temperature set
points.

Accelerated Ice Production

This feature assists with temporary periods of heavy ice use by

increasing ice production over a 24-hour period.

• Press the accelerated ice production touch pad to set the
freezer temperature to -10°F (-23°C). The refrigerator
temperature will not change. The accelerated ice setting will
remain on for 24 hours unless manually turned off.

NOTES:

• The temperature display will not change. After 24 hours, the
refrigerator returns to the previous temperature set points.

• If increased ice production is desired at all times, set the

Freezer Control to a colder number. Setting the freezer to a

colder temperature may make some foods, such as ice
cream, harder.

Additional Digital Control Panel Features

Additional features are located on the control panel at the top of
the refrigerator compartment.

WATER FILTER Status & Reset

NOTE: Do not use with water that is microbiologically unsafe
or of unknown quality without adequate disinfection before
or after the system.

11

Cut Hazard

Use a sturdy glass when dispensing ice or water.

Failure to do so can result in cuts.

Depending on your model, you may have one or more of the
following options: the ability to select either crushed or cubed
ice, a special light that turns on when you use the dispenser, or a
lock option to avoid accidental dispensing.

The ice dispenser

3,

Remove the glass to stop dispensing.
NOTE: The first few batches of ice may have an off-flavor

from new plumbing and parts. Throw the ice away. Also, take

large amounts of ice from the ice bin, not through the

dispenser.

The water dispenser

If you did not flush the water system when the refrigerator was

first installed, press the water dispenser bar with a glass or jar

until you draw and discard 2 to 3 gal. (8 to 12 L) or approximately
6 to 7 minutes of water after water begins dispensing. It will take
3 to 4 minutes for the water to begin dispensing. The water you
draw and discard cleans the system and helps clear air from the

lines. Allow several hours for the refrigerator to cool down and
chill water.

IMPORTANT: Depending on your model, the small removable
tray at the bottom of the dispenser is designed to catch small
spills and allow for easy cleaning. There is no drain in the tray.
The tray can be removed from the dispenser and carried to the
sink to be emptied or cleaned.

Ice dispenses from the ice maker storage bin in the freezer. When
the dispenser lever is pressed:

• A trap door opens in a chute between the dispenser and the
ice bin. Ice moves from the bin and falls through the chute.

• When you release the dispenser lever, the trap door closes
and the ice dispensing stops. The dispensing system will not
operate when the freezer door is open.

Some models dispense both cubed and crushed ice. Before
dispensing ice, select which type of ice you prefer. The button
controls are designed for easy use and cleaning.

• For cubed ice, press the CUBE button until the red indicator
appears in the window above the CUBE button.

ICE

CRUSH CUBE

• For crushed ice, press the CRUSH button until the red
indicator appears inthe window above the CRUSH button.

For crushed ice, cubes are crushed before being dispensed. This
may cause a slight delay when dispensing crushed ice. Noise
from the ice crusher is normal, and pieces of ice may vary in size.
When changing from CRUSH to CUBE, a few ounces of crushed

ice will be dispensed along with the first cubes.

TO dispense ice:

1. Press button for the desired type of ice.

2. Press a sturdy glass against the ice dispenser lever. Hold the
glass close to the dispenser opening so ice does not fall
outside of the glass.

To dispense water:

1. Press a glass against the water dispenser lever.

2. Remove the glass to stop dispensing.
NOTE: Dispense enough water every week to maintain a fresh

supply.

The dispenser light

The dispenser area has a light. It can be turned on manually by

pressing the QN button at the right-hand side of the control
panel. The red indicator above the QN button will appear.

Qn some models: Whenever you use the dispenser the lever will
automatically turn the light on.

LIGHT

OFF ON

NOTE: See the "Changing the Light Bulbs" section for

information on changing the dispenser light bulb.

On models without crushed ice, the light switch is a rocker-style
type. Push the switch to turn the light on, and push again to turn

the light off.

IMPORTANT: You do not need to apply a lot of pressure to
the lever in order to activate the ice dispenser. Pressing hard
will not make the ice dispense faster or in greater quantities.

12

.................................................... After changing the water filter cartridge, reset the water filter

The dispenser lock (on some models) status light by pressing and holding the RESET for 2 seconds.

The indicator light will change to 99% when the filter indicator is
Your dispenser can be turned off for easy cleaning or to prevent
accidental dispensing by small children and pets. To turn off the
dispenser, press the LOCK button. The indicator will appear
above the LOCK button and the ice and water dispensers will not
work. To unlock the dispenser, press the UNLOCK button until
the indicator appears. Then continue to dispense ice or water as

usual.

reset.

Changing the Base Grille Filter

1. Locate the water filter cartridge cap in the front base grille.
Rotate the cap counterclockwise to a vertical position and

pull the cap and filter cartridge out through the base grille.

NOTE: There will be water in the cartridge. Some spilling may

occur.

DISPENSER

2. Remove the cartridge cap by sliding it off the end of the old
cartridge. The cap will slide to the left or right. DO NOT

LOCK UNLOCK

DISCARD THE CAR

NOTE: The lock feature does not shut off power to the product,
to the ice maker, or to the dispenser light. It simply deactivates
the dispenser levers.

The base grille water filter status light
The water filter status display or light will help you know when to

change your water filter cartridge. The display or light is located
at the top of the refrigerator compartment.

NOTE: Do not use with water that is microbiologically unsafe
or of unknown quality without adequate disinfection before

or after the system.

Style 1: Electronic Status Light (on some models)

A new water filter should display a Good (green) status. As the
filter life is used, the light will change from Good (green) to Order

(yellow). This tells you that it is almost time to change the water
filter cartridge (90% of the filter life has been used). It is

recommended that you replace the base grille water filter
cartridge when the water filter indicator light changes to Replace

(red) OR when water flow to your water dispenser or ice maker
decreases noticeably. (See "Changing the Base Grille Filter" later
in this section.)

WA_ER FILER

BOOD•

QBD_• _5ET

RmSq_O

After changing the water filter cartridge, reset the water filter
indicator by pressing and holding the RESET for 2 seconds. The

status light will change from Replace (red) to Good (green) when
the filter indicator is reset.

Style 2: Digital Status Display (on some models)

A new water filter should display a reading of 99% and will
continue to decrease as the filter life is used. When display reads

10%, it is time to order a replacement filter. It is recommended

that you replace the base grille water filter cartridge when the
water filter indicator light changes to 0% OR when water flow to

your water dispenser or ice maker decreases noticeably. (See
"Changing the Base Grille Filter" later in this section.)

WA'IER FILTER

3. Take the new cartridge out of its packaging and remove

protective cover from o-rings.

4. Slide the cartridge cap onto the new cartridge. See

illustration in Step 2.

5. With cartridge cap in the vertical position, push the new filter
cartridge into the base grille until it stops. Rotate the cartridge
cap clockwise to a horizontal position. Flush the water
system (see "Flushing the Water System After Replacing

Filter" section).

Flushing the Water System After Replacing Filter

Use a sturdy container to depress the water dispenser bar until
the water begins to flow. Flush the water system by dispensing
and discarding 2 to 3 gal. (8 to 12 L) of water. Cleaning the
system will take approximately 6 to 7 minutes and will help clear
air from the line. Additional flushing may be required in some

households.

NOTE: As air is cleared from the system, water may spurt out of
the dispenser.

Using the dispenser without the water filter
You can run the dispenser without a water filter cartridge. Your

water will not be filtered.

1. Remove the base grille water filter cartridge.

2. Slide the cartridge cap off the end of the filter cartridge. DO

NOT DISCARD THE CAR With the cartridge cap in the
vertical position, insert the cap into the base grille until it
stops.

PERCENTREMAINING

3. Rotate the cartridge cap to a horizontal position. The
cartridge cap might not be even with the base grille.

13

}_S _e _o es_ Ai<es o@

To turn the ice maker on/off:

The ON/OFF switch is located on the top right side of the freezer
compartment.

1. To turn the ice maker on, slide the control to the ON (left)
position.

NOTE: Your ice maker has an automatic shutoff. The ice
maker sensors will automatically stop ice production, but the

control will remain in the ON (left) position.

2. To manually turn the ice maker off, slide the control to the
OFF (right) position.

To remove and replace ice bucket:

1. Place four fingers in bucket base opening and rest thumb on
the release button.

2. Holding the base of the bucket with both hands, depress the
release button and lift the bucket up and out. It is not
necessary to turn the ice maker control to the OFF (right)

position. The ice maker will not produce ice without the
bucket installed in the door.

Accelerated Ice Production

The accelerated ice feature assists with temporary periods of

heavy ice usage by increasing ice production over a 24-hour
period.

• Press ICE touch pad to set the freezer temperature to -10°F
(-23°C). The accelerated ICE setting will remain on for 24

hours unless manually turned off.

If increased ice production is desired at all times, set the
Freezer Control to a colder number. Setting the freezer to a

colder temperature may make some foods, such as ice
cream, harder.

REFRIGERATOR

FEATURES

Your model may have some or all of these features. Features that
can be purchased separately as product accessories are labeled
with the word "Accessory." Not all accessories will fit all models.

Ifyou are interested in purchasing one of the accessories, please

call the toll-free number on the cover or in the "Accessories"
section.

Important information to know about glass shelves

and covers:

Do not clean glass shelves or covers with warm water when
they are cold. Shelves and covers may break if exposed to
sudden temperature changes or impact, such as bumping.

For your protection, tempered glass is designed to shatter

into many small, pebble-size pieces. This is normal. Glass
shelves and covers are heavy. Use special care when re-
moving them to avoid impact from dropping.

To care for ice storage bucket:

1. Empty the ice bucket. Use warm water to melt the ice if
necessary.

NOTE: Never use anything sharp to break up the ice in the
bin or bucket. This can cause damage to the ice container
and the dispenser mechanism.

2. Wash ice bucket with a mild detergent, rinse well and dry
thoroughly. Do not use harsh or abrasive cleaners or solvents.

REMEMBER:

• Allow 24 hours to produce the first batch of ice.

• Discard the first three batches of ice produced to avoid
impurities that may be flushed out of the system.

• The quality of your ice will be only as good as the quality of
the water supplied to your ice maker.

Avoid connecting the ice maker to a softened water supply.
Water softener chemicals (such as salt) can damage parts of
the ice maker and lead to poor quality ice. If a softened water
supply cannot be avoided, make sure the water softener is
operating properly and is well maintained.

• It is normal for the ice cubes to be attached at the corners.
They will break apart easily.

• Do not store anything in the ice maker or ice bucket.

14

Your model may have glass or wire shelves. Store similar foods
together and adjust the shelves to fit different heights. This
reduces the time the refrigerator door is open and saves energy.

Slide-out Shelves (on some models)

To remove and replace a shelf in a metal frame:

1. Pull the shelf forward to the stop. Tilt the front of the shelf up
and lift it slightly as you pull the shelf from the frame.

2. Replace the shelf by guiding it back into the slots on the
frame and pushing the shelf in past the stop.

Shelves and Shelf Frames

To remove and replace a shelf/frame:

1. Remove the shelf/frame by tilting it up at the front and lifting it

out of the shelf supports,

2. Replace the shelf/frame by guiding the rear shelf hooks into
the shelf supports, Tilt the front of the shelf up until rear shelf
hooks drop into the shelf supports. Check to make sure that
the shelf is securely in position.

To raise or lower the shelf:.

1. Raise the shelf by pulling forward on the lever located at the

bottom front of the shelf and lift until the shelf locks into the
vertical position,

2. Lower the shelf until it is latched securely in place.

The dell drawer stores raisins, nuts, spreads, and other small

items at normal refrigerator temperatures,

To remove and replace the dell drawer:

1, Remove the dell drawer by sliding it straight out to the stop.

Lift the front and slide the drawer out the rest of the way.

2, Replace the dell drawer by sliding it back past the stop.

Crisper and Convertible Vegetable Meat Drawers

To remove and replace drawers: _'+_*"

1. Slide crisper or meat drawer straight out to the stop, Lift the _}

front of drawer with one hand while supporting the bottom of
drawer with other hand and slide the drawer out the rest of

the way.

2, Replace the crisper or meat drawer by sliding it back in fully

past the drawer stop,

To raise or lower the shelf:.

1. Raise the shelf by first sliding it back and down to make it

half-width. (You can use the shelf in this position to allow
taller items to be stored on the shelf below.)

2. Lift the front of the shelf until it fits securely in place against
the back wall. Lower the shelf securely back into position.

3. Pull the front of the shelf forward until it fits into place.

Crisper or Vegetable/Meat Drawer Covers

To remove and replace covers:

1. Remove the crisper and meat drawer, Press up in center of

crisper glass insert until it rises above the plastic frame.

Holding the crisper glass firmly, carefully slide the glass insert

forward to remove.

2, Lift crisper cover frame and remove. Repeat steps to remove

the meat drawer cover.

3. Replace back of meat drawer cover frame into supports or
slides on side walls of the refrigerator and lower or slide the
front of the cover frame into place.

4, Slide rear of glass insert into cover frame and lower front into

place. Repeat steps to replace the crisper cover.

15

(-o "_J_/o

The convertible vegetable/meat drawer can be adjusted to
properly chill meats or vegetables. The air inside the pan is
cooled to prevent "spot" freezing and can be set to keep meats
at the National Livestock and Meat Board recommended storage
temperatures of 28°- 32°F (-2°- 0°C).

IMPORTANT: To extend freshness, wrap meats in airtight,
moisture-proof materials before storing. Always store meat as

recommended.

Adjusting the control

The convertible control comes preset at the lowest meat setting.
To change a control setting: Move the control to the right (colder)

or to the left (less cold) as desired.
To store vegetables: Set the control to VEG (all the way to the left)

to store vegetables at their optimal storage temperatures (which
need to be warmer than those for meat).

IMPORTANT: If food starts to freeze, move the control to the left
(less cold). Remember to wait 24 hours between adjustments.

Doing so gives the temperature of the food time to change.
Meat storage guide

Store most meat in original wrapping as long as it is airtight and
moisture-proof. Rewrap if necessary. See the following chart for
storage times. When storing meat longer than the times given,

freeze the meat.

Fresh fish or shellfish .................. use same day as purchased

Chicken, ground beef, variety meat (liver, etc.) ......... 1-2 days

Cold cuts, steaks/roasts ............................................ 3-5 days

Cured meats ............................................................ 7-10 days

Leftovers - Cover leftovers with plastic wrap, aluminum foil, or
plastic containers with tight lids.

Humidity control location:

• Humidity Control on crisper drawer (Style 1 - on left)

• Humidity Control on crisper cover (Style 2 - on right)

HI_ li 4 3 2 I Low

To remove and replace the wine rack (left) or can/bottle

rack (right):

1. Remove the rack by pulling it straight out from the shelf.

2. Replace the rack by sliding it in between the shelf and the
wall of the refrigerator.

NOTE: For long-term storage, place eggs in a covered container

or in their original carton on an interior shelf.

FEATURES

Your model may have some or all of these features. Features that
can be purchased separately as product accessories are labeled
with the word "Accessory." Not all accessories will fit all models.

Ifyou are interested in purchasing one of the accessories, please

call the toll-free number on the cover or in the "Accessories"
section.

You can control the amount of humidity in the moisture-sealed
crisper. Adjust the control to any setting between LOW and

HIGH.
LOW (open) lets moist air out of the crisper for best storage of

fruits and vegetables with skins.

• Fruit: Wash, let dry and store in refrigerator in plastic bag or
crisper. Do not wash or hull berries until they are ready to use.

Sort and keep berries in original container in crisper, or store
in a loosely closed paper bag on a refrigerator shelf.

• Vegetables with skins: Place in plastic bag or plastic
container and store in crisper.

HIGH (closed) keeps moist air inthe crisper for best storage of
fresh, leafy vegetables.

• Leafy vegetables: Wash in cold water, drain and trim or tear
off bruised and discolored areas. Place in plastic bag or

plastic container and store in crisper.

16

To remove and replace the shelf:.

1. Lift the shelf off of the supports.

2. Slide it out of the shelf support holes.

3. Replace shelf in the reverse order.

Frozen food storage guide

Storage times will vary according to the quality and type of food,
the type of packaging or wrap used (should be airtight and
moisture-proof), and the storage temperature. Ice crystals inside
a sealed package are normal. This simply means that moisture in
the food and air inside the package have condensed, creating ice

crystals.

Put no more unfrozen food into the freezer than will freeze within
24 hours (no more than 2 to 3 Ibs. of food per cubic foot

[907-1,350 g per L] of freezer space). Leave enough space in the
freezer for air to circulate around packages. Be careful to leave
enough room for the door to close tightly.

For more information on preparing food for freezing, check a
freezer guide or reliable cookbook.

The freezer basket or bin can be used to store bags of frozen
fruits and vegetables that may slide off freezer shelves.

TO remove and replace the freezer basket or bin:

1. Remove basket or bin by sliding it out to the stop.

2. Lift the front of the basket or bin and slide it out the rest of the
way.

Drop-in Door Rails

To remove and replace the rails:

1. Remove the rails by pulling straight up on each end of the rail.

2. Replace the rails by sliding the shelf rail into the slots on the
door and pushing the rail straight down until it stops.

NOTE: Can racks may be purchased as an Accessory for some

models.
To remove and replace the racks/bins:

1. Remove the rack/bin by lifting it and pulling it straight out.

2. Replace the racWbin by sliding it in above the desired
support and pushing it down until it stops.

3. Replace the basket or bin by positioning it on the side wall
guide rails. Lift the basket or bin front slightly while pushing it
past the guide rail stops and slide basket or bin in the rest of
the way.

DOOR FEATURES

Your model may have some or all of these features. Features that
can be purchased separately as product accessories are labeled
with the word "Accessory." Not all accessories will fit all models.
If you are interested in purchasing one of the accessories, please

call the toll-free number on the cover or in the "Accessories"
section.

The door rails may be removed for easier cleaning.

Snap-on Door Rails

To remove and replace the rails:

1. Remove the rails by pushing in slightly on the front of the
bracket while pulling out on the inside tab. Repeat these

steps for the other end of the rail.

2. Replace the rails by aligning the ends of the brackets with the
buttons on the sides of the door liner. Firmly snap bracket
and rail assembly onto the tabs above the shelf as shown.

REFRIGERATOR CARE

Explosion Hazard

Use nonflammable cleaner.
Failure to do so can result in death, explosion,

or fire.

Both the refrigerator and freezer sections defrost automatically.
However, clean both sections about once a month to prevent

odors from building up. Wipe up spills immediately.

17

Cleaning your refrigerator

1. Unplug refrigerator or disconnect power.

2. Remove all removable parts from inside, such as shelves,
crispers, etc.

3. Hand wash, rinse, and dry removable parts and interior
surfaces thoroughly. Use a clean sponge or soft cloth and a
mild detergent in warm water.

• Do not use abrasive or harsh cleaners such as window

sprays, scouring cleansers, flammable fluids, cleaning
waxes, concentrated detergents, bleaches or cleansers
containing petroleum products on plastic parts, interior
and door liners or gaskets. Do not use paper towels,
scouring pads, or other harsh cleaning tools. These can
scratch or damage materials.

• To help remove odors, you can wash interior walls with a

mixture of warm water and baking soda (2 tbs. to 1 qt.
[26 g to .95 L] of water).

4. Wash stainless steel and painted metal exteriors with a clean
sponge or soft cloth and a mild detergent in warm water. Do
not use abrasive or harsh cleaners. Dry thoroughly with a soft
cloth. For additional protection against damage to painted
metal exteriors, apply appliance wax (or auto paste wax) with
a clean, soft cloth. Do not wax plastic parts.

NOTE; To keep your Stainless Steel refrigerator looking like
new and to remove minor scuffs or marks, it is suggested that
you use the manufacturer's approved Stainless Steel Cleaner

& Polish.
IMPORTANT: This cleaner is for Stainless Steel parts only!

Do not allow the Stainless Steel Cleaner & Polish to come into
contact with any plastic parts such as the trim pieces,

dispenser covers or door gaskets. If accidental contact does
occur, clean plastic part with a sponge and mild detergent in
warm water. Dry thoroughly with a soft cloth. To order the

cleaner, see the "Accessories" section.

5. There is no need for routine condenser cleaning in normal
home operating environments. If the environment is
particularly greasy or dusty, or there is significant pet traffic in
the home, the condenser should be cleaned every two to
three months to ensure maximum efficiency.

If you need to clean the condenser:

• Remove the base grille (see "Base Grille" or "Door

Removal" section).

• Use a vacuum with a soft brush to clean the grille, the

open areas behind the grille and the front surface area of
the condenser.

• Replace the base grille when finished.

6. Plug in refrigerator or reconnect power.

Dispenser Light (on some models)

Reach through the dispenser area to remove and replace
light bulb.

!. Dispenser Light

Refrigerator Control Panel Light

Reach behind the refrigerator control panel to remove and

replace light bulb.

Refrigerator Crisper Light or Upper Freezer Light (on some

models)

• Remove light shield by grasping the top center of the shield
and pulling forward while turning it slightly to one side. If

necessary, remove top crisper drawer to access crisper light

shield.

Replace the light shield by inserting the tabs on one end into
the slotted holes in the refrigerator or freezer liner. Then,
carefully bend the shield at the center to insert the tabs on

the other end.

Upper Freezer Light (on some models)

• Remove the light shield by grasping the sides and squeezing
in toward the center and while pulling forward the shield.

Replace the light shield by fitting the tabs into the slotted
holes in the freezer liner. Push in the shield until it snaps into
place.

NOTE: Not all appliance bulbs will fit your refrigerator. Be sure to
replace the bulb with one of the same size and shape. The
dispenser light requires a heavy duty 10-watt bulb. All other lights
require a 40-watt appliance bulb. Replacement bulbs are
available from your dealer.

1. Unplug refrigerator or disconnect power.

2. Remove light shield when applicable as shown.
NOTE: To clean the light shield, wash it with warm water and

liquid detergent. Rinse and dry the shield well.

3. Remove light bulb and replace with one of the same size,
shape and wattage.

4. Replace light shield when applicable as shown.

5. Plug in refrigerator or reconnect power.

18

Lower Freezer Light Beneath Ice Bin (on some models)

• Remove the light shield by grasping the sides and squeezing
in toward the center. Once the side hooks of shield are free

from the freezer lining, pull down the shield.

Replace the light shield by squeezing the sides toward the

center and inserting the side hooks into the slotted holes.
Once the side hooks are in place, snap the front tab into the

slotted hole.

Lower Freezer Light Behind Top Freezer Basket (on some
models)

• Depending on your model, remove the top freezer basket or
top freezer basket shelf. Remove light shield by removing the
Phillips screw on the top of the shield. Carefully, rotate the
shield until the left tab can be gently pulled from the freezer

wall.

• Replace the light shield by inserting the left tab into the
freezer wall. Align top tab with screw hole and replace screw.

If the power will be out for 24 hours or less, keep both refrigerator
doors closed to help food stay cold and frozen.

If the power will be out for more than 24 hours, do one of the
following:

• Remove all frozen food and store it in a frozen food locker.

• Place 2 Ibs. (907 g) of dry ice in the freezer for every cubic
foot (28 L) of freezer space. This will keep the food frozen for

two to four days.

• If neither a food locker nor dry ice is available, consume or
can perishable food at once.

REMEMBER: A full freezer stays cold longer than a partially filled
one. A freezer full of meat stays cold longer than a freezer full of
baked goods. Ifyou see that food contains ice crystals, it may be
refrozen, although the quality and flavor may be affected. If the
condition of the food is poor, dispose of it.

Vacations

If you choose to leave the refrigerator on while you're away:

1. Use up any perishables and freeze other items.

2. If your refrigerator has an automatic ice maker:

• Raise wire shutoff arm to OFF (up) position or move the

switch to the OFF (right) setting.

• Shut off water supply to the ice maker.

3. Empty the ice bin.

If you choose to turn the refrigerator off before you leave:

t. Remove all food from the refrigerator.

2. If your refrigerator has an automatic ice maker:

• Turn off the water supply to the ice maker at least one day
ahead of time.

• When the last load of ice drops, raise the wire shutoff arm

to the OFF (up) position or move the switch to the OFF

(right) setting.

3. Depending on your model, turn the Thermostat Control or
Refrigerator Control to OFF. See the "Setting or Using the

Control(s)" section.

4. Clean refrigerator, wipe it, and dry well.

5. Tape rubber or wood blocks to the tops of both doors to prop

them open far enough for air to get in. This stops odor and
mold from building up.

Moving

When you are moving your refrigerator to a new home, follow
these steps to prepare it for the move.

1. If your refrigerator has an automatic ice maker:

• Turn off the water supply to the ice maker at least one day
ahead of time.

• Disconnect the water line from the back of the
refrigerator.

• When the last load of ice drops, raise the wire shutoff arm

to the OFF (up) position or move the switch to the OFF

(right) setting.

2. Remove all food from the refrigerator and pack all frozen food
in dry ice.

3. Empty the ice bin.

4. Depending on your model, turn the Thermostat Control or
Refrigerator Control to OFF. See the "Setting or Using the

Controls" section.

5. Unplug the refrigerator.

6. Empty water from the defrost pan.

7. Clean, wipe, and dry thoroughly.

8. Take out all removable parts, wrap them well, and tape them

together so they don't shift and rattle during the move.

9. Depending on the model, raise the front of the refrigerator so
it rolls more easily OR screw in the leveling legs so they don't

scrape the floor. See the "Door Closing" or "Leveling Your

Refrigerator" section.

10. Tape the doors shut and the power cord to the refrigerator
cabinet.

When you get to your new home, put everything back and refer to
the "Refrigerator Installation" section for preparation instructions.
Also, if your refrigerator has an automatic ice maker, remember to
reconnect the water supply to the refrigerator.

19

• Are the door gaskets not sealed all the way around?

TROUBLESHOOTING contactatechnic,anorother0ua,fiedperson.

NOTE: Your new refrigerator will run longer than your old one

due to its high-efficiency motor.

Try the solutions suggested here first in order to avoid the
cost of an unnecessary service call.

Your refrigerator will not operate

• Is the power supply cord unplugged? Plug into a grounded
3 prong outlet.

• Has a household fuse or circuit breaker tripped? Replace
the fuse or reset the circuit breaker.

• Is the refrigerator or freezer control turned to the OFF
position? Refer to the "Setting or Using the Controls"

section.
Is the refrigerator defrosting? Recheck to see if the

refrigerator is operating in 30 minutes. Your refrigerator will
regularly run an automatic defrost cycle.

Is the refrigerator not cooling? For models with digital
controls, turn the unit OFF then ON again to reset. See the
"Setting or Using the Controls" section, if this does not
correct the problem, call for service.

The lights do not work

Is the power supply cord unplugged? Plug into a grounded

3 prong outlet.
Is a light bulb loose in the socket or burned out? See the

"Changing the Light Bulb(s)" section.

There is water in the defrost drain pan

• Is the refrigerator defrosting? The water will evaporate, it is
normal for water to drip into the defrost pan.

• Is it more humid than normal? When it is humid, expect that
the water in the defrost pan will take longer to evaporate.

The motor seems to run too much

Is the room temperature hotter than normal? The motor

will run longer under warm conditions. At normal room
temperatures, expect your motor to run about 40% to 80% of
the time. Under warmer conditions, it will run even more.

Has a large amount of food just been added to the
refrigerator? Adding a large amount of food warms the

refrigerator. The motor normally will run longer to cool the
refrigerator back down.

Are the doors opened often? The motor will run longer
when this occurs. Conserve energy by getting all items out at
one time, keeping food organized, and closing the door as
soon as possible.

Are the controls not set correctly for the surrounding
conditions? Refer to the "Setting or Using the Controls"

section.
Are the doors not closed completely? Close the doors

firmly. If they do not close completely, see "The doors will not
close completely" later in this section.

Are the condenser coils dirty? This prevents air transfer and
makes the motor work harder. Clean the condenser coils.

Refer to the "Cleaning" section.

The refrigerator seems to make too much noise

• The sounds may be normal for your refrigerator. See the
"Normal Sounds" section.

The ice maker is not producing ice or not enough ice

• Has the ice maker just been installed? Wait 72 hours for full

ice production to begin. Once your refrigerator is cooled, the
ice maker should produce 70 to 120 cubes every 24 hours.

Is the freezer temperature cold enough to produce ice?

Wait 24 hours after ice maker hook-up for ice production. See
the "Setting or Using the Controls" section.

Is the ice maker wire shutoff arm in the OFF (arm up)
position (on some models)? Lower the wire shutoff arm to
the ON (arm down) position. See the "ice Maker and Storage

Bin/Bucket" section.

Is the ice maker switch in the OFF (right) position (on
some models)? Move ice maker switch to the ON (left)

position. See the "ice Maker and Storage Bin/Bucket"
section.

Is the water line shutoff valve to the refrigerator turned
on? Turn on the water valve. See the "Water Supply

Connection" section.

Does the ice maker mold have water in it or has no ice

been produced? Make sure your refrigerator has been
connected to a water supply and the supply shutoff valve is
turned on. See the "Water Supply Connection" section.

Is an ice cube jammed in the ice maker ejector arm?

For models with an interior ice bin, remove the ice from the
ejector arm with a plastic utensil. For models with an ice

bucket located on the freezer door, access the ice maker by
depressing the ice sensor door on the upper left side of the
freezer interior. While depressing the sensor door, lift the ice
maker service door and remove the ice from the ejector with
a plastic utensil. See the "ice Maker and Storage Bin/Bucket"

section.

Has a large amount of ice just been removed? Allow 24

hours for ice maker to produce more ice.
Are the controls set correctly? See the "Setting or Using

the Controls" section.

Is there a water filter installed on the refrigerator? The
filter may be clogged or installed incorrectly. Check the filter

installation instructions to ensure that the filter was installed
correctly and is not clogged. If installation or clogging is not a

problem, call a technician or other qualified person.

NOTE: If not due to any of the above, there may be a problem

with the water line. Call for service.

20

Off-taste, odor or gray color in the ice Ice bucket difficult to remove

• Are the plumbing connections new, causing discolored or
off-flavored ice? Discard the first few batches of ice.

• Have the ice cubes been stored too long? Throw old ice
away and make a new supply.

• Does the freezer and ice bin or bucket need to be
cleaned? See the "Cleaning" or "Ice Maker and Storage Bin/

Bucket" section.

• Has food in the freezer or refrigerator been wrapped
properly? Use airtight, moisture-proof packaging to help
prevent odor transfer to stored food.

• Does the water contain minerals (such as sulfur)? A filter
may need to be installed to remove the minerals.

• Is there a water filter installed on the refrigerator? Gray or
dark discoloration in ice indicates that the water filtration

system needs additional flushing. Run additional water
through the water dispenser to flush the water filtration
system more thoroughly (at least 2 to 3 gal. [8 to 12 L] or 6 to
7 minutes initially). Discard discolored ice.

The ice dispenser will not operate properly

• Is the freezer door closed completely? Push the door firmly
shut. if it will not shut all the way, see "The doors will not

close completely" later in this section.

• Is the ice bin or bucket installed correctly? For models
with an interior ice bin, push the ice bin in all the way. If the
ice bin does not go inall the way, it may not be put in straight.
Pull it out and try again. For models with an ice bucket
located on the freezer door, the bucket should sit level. To
remove the bucket, press the release button on the right side

of the bucket and lift straight up. Replace the bucket in the
door making sure it is properly aligned and snapped securely

into place. Refer to the "Ice Maker and Storage Bin/Bucket"
section.

• Has the wrong ice been added to the bin or bucket? Use
only cubes produced by the current ice maker. If other cubes
have been added, remove all cubes and check to see that
none have become stuck in the delivery chute.

• Has the ice frozen in the ice bin or bucket? Shake the ice
bin or bucket to separate cubes. If cubes do not separate,

empty bin or bucket and wait 24 hours for ice to restock.

• Has the ice melted around the auger (metal spiral) in the
ice bucket? Dump the ice cubes and clean the ice bucket
completely. Allow 24 hours for the ice maker to restock. Do
not try to remove the melted ice with a sharp object. You
could damage the ice bucket.

• Is ice stuck in the delivery chute? Clear the ice from the
delivery chute with a plastic utensil. Do not use anything
sharp to remove the ice. You could cause damage.

• Is the ice dispenser stalling while dispensing "crushed"
ice? Stop dispensing ice. Change the ice button from
"crushed" to "cubed." Depress the ice dispenser arm using a
sturdy glass. If cubed ice dispenses correctly, depress the
button for "crushed" ice and begin dispensing again. Refer to
the "Water and Ice Dispensers" section.

• Is there ice in the bucket? See "The ice maker is not
producing ice" earlier in this section.

• Has the dispenser arm been held in too long? Release
dispenser arm. Ice will stop dispensing when the arm is held
in too long. Wait three minutes for dispenser motor to reset
before using again, it is best to take large amounts of ice
directly from the ice bin or bucket, not through the dispenser.

• Is the ice bucket difficult to remove (on some models)?
For models with an ice bucket located on the freezer door,

select "cubed" ice. Using a sturdy glass, quickly depress and
release the ice dispenser arm. Open the freezer door, depress
the release button on the ice bucket and lift upward. Refer to
the "ice Maker and Storage Bin/Bucket" section.

The water dispenser will not operate properly

• Has the water system not filled? The water system needs

to be filled the first time it is used. Use a sturdy container to
depress the water dispenser bar until the water begins to
flow. Flush the water system by dispensing and discarding
2 to 3 gal. (8 to 12 L)of water. Cleaning the system will take
approximately 6 to 7 minutes and will help clear air from the

line. Additional flushing may be required in some households.

See the "Water and Ice Dispensers" section.

Is the water shutoff valve not turned on or the water line

connected at the source? Make sure the water shutoff valve

is turned on and the water source is connected to the

refrigerator. See the "Water Supply Connection" section,

Is the water shutoff valve clogged or incorrectly installed?

See the "Water Supply Connection" section. If clogging or

installation is not a problem, call for service or contact a
plumber.

Is there a kink in the home water source line? If you find or

suspect a kink in the water line, call for service.

Is there a water filter installed on the refrigerator? The

filter may be clogged or incorrectly installed. First, check the
filter installation instructions to ensure that the filter was

installed correctly and is not clogged. If installation or

clogging is not a problem, call for service.

Water or ice is leaking from the dispenser

Is the glass not being held under the ice dispenser long

enough, causing the ice to spill? Hold the container under
the ice chute for two to three seconds after releasing the

dispenser lever. Water or ice may continue to dispense during
this time.

Is an ice cube stuck in the chute and holding the trap

door open? Remove the cube.

Is there a water filter installed on the refrigerator? The

water filtration system may have air in the lines, causing water
to drip. Additional flushing may help clear air from the lines.

Normal dispenser use should flush air from the lines within 24

to 72 hours.

Water flow from the dispenser decreases noticeably

• Is there a water filter installed on the refrigerator?

The filter may be full or incorrectly installed. Remove the
water filter cartridge (see the "Water Filtration System"

section). Operate the dispenser. If the water flow increases

noticeably, replace the filter.

21

The dispenser water is not cool enough The doors will not close completely

• Has the refrigerator been newly installed? Allow 24 hours • Are food packages blocking the door open? Rearrange
for the refrigerator to cool completely.

• Has a large amount of water been recently dispensed?
Allow 24 hours for the water to cool completely.

• Has water not been recently dispensed? The first glass of
water may not be cool. Discard the first glass of water.

The divider between the two compartments is warm

The warmth is probably due to normal operation of the
automatic exterior moisture control. If still concerned, call for

service.

Temperature is too warm

Are the air vents blocked in either compartment? This

prevents the movement of cold air from the freezer to the
refrigerator. Remove any objects from in front of the air vents.

See the "Ensuring Proper Air Circulation" section for the
location of air vents. •

Are the door(s) opened often? The refrigerator will warm
when this occurs. Keep the refrigerator cool by getting all

items out at one time, keeping food organized, and closing
the door as soon as possible.

Has a large amount of food just been added to the
refrigerator or freezer? Adding a large amount of food

warms the refrigerator. It can take several hours for the
refrigerator to return to the normal temperature.

Are the controls set correctly for the surrounding
conditions? See the "Setting or Using the Controls" section.

Is the refrigerator not cooling? For models with digital
controls, turn the unit OFF then ON again to reset. See the
"Setting or Using the Controls" section. If this does not

correct the problem, call for service.

There is interior moisture buildup

containers so that they fit more tightly and take up less
space.

Is the ice bin or ice bucket out of position? For models

with an interior ice bin, push the ice bin in all the way. If the

ice bin does not go in all the way, it may not be put in straight.
Pull it out and try again. For models with an ice bucket

located on the freezer door, the bucket should sit level. To
remove the bucket, press the release button on the right side
of the bucket and lift straight up. Replace the bucket in the
door making sure it is properly aligned and snapped securely

into place. See the "ice Maker and Storage Bin/Bucket"
section.

Are the pans, shelves, bins, or baskets out of position?

Put the crisper cover and all pans, shelves, bins, and baskets

back into their correct positions. See the "Crisper and Crisper
Covers" section for more information.

Are the gaskets sticking? Clean gaskets according to the
directions in the "Cleaning" section.

Does the refrigerator wobble or seem unstable? Level the
refrigerator. See the "Door Closing" or "Leveling Refrigerator"
section, depending on your model.

Were the doors removed during product installation and
not properly replaced? Remove and replace the doors

according to the "Door Removal" section on some models, or
call a qualified service technician.

The doors are difficult to open

• Are the gaskets dirty or sticky?. Clean gaskets according to
the directions in the "Cleaning" section.

Computer Troubleshooting (on some models)

See the "Computer and Software User Guide" for information
regarding your computer system.

• Are the air vents blocked in the refrigerator? Remove any
objects from in front of the air vents. See the "Ensuring

Proper Air Circulation" section for the location of air vents.
Are the door(s) opened often? Avoid humidity buildup by

getting all items out at one time, keeping food organized, and
closing the door as soon as possible.

Is the room humid? It is normal for moisture to build up
inside the refrigerator when the room air is humid.

Is the food packaged correctly? Check that all food is
securely wrapped. Wipe off damp food containers before

placing in the refrigerator.
Are the controls set correctly for the surrounding

conditions? See the "Setting or Using the Controls" section.
Was a self-defrost cycle completed? It is normal for

droplets to form after the refrigerator self-defrosts.

22

SERVICE

Master Protection Agreements

Congratulations on making a smart purchase. Your new
Kenmore_' appliance is designed and manufactured for years of

dependable operation. But like all products, it may require
preventive maintenance or repair from time to time. That's when

having a Master Protection Agreement can save you money and
aggravation.

Your purchase has added value because you can depend on
Sears HomeCentraF *for service. With over 2,400 Service

Technicians and access to over 900,000 parts and accessories,
we have the tools, parts, knowledge and skills to back our

pledge: We Service What We Sell.

Sears Maintenance Agreements

Your Kenmore _ appliance is designed, manufactured and tested
to provide years of dependable operation. Yet any major
appliance may require service from time to time. The Sears

Maintenance Agreement offers you an outstanding service
program, affordably priced.

Purchase a Master Protection Agreement now and protect

yourself from unexpected hassle and expense.

The Master Protection Agreement also helps extend the life of
your new appliance. Here's what's included in the Agreement:

Expert service by our 12,000 professional repair specialists
Unlimited service and no charge for parts and labor on all

covered repairs
"No-lemon" guarantee - replacement of your covered

product if more than three product failures occur within twelve
months

Product replacement ifyour covered product can't be fixed

Annual Preventive Maintenance Check at your request- no

extra charge

Fast help by phone - non-technical and instructional

assistance on products repaired in your home, plus convenient
repair scheduling

Power surge protection against electrical damage due to
power fluctuations

Rental reimbursement if repair of your covered product

takes longer than promised

Once you purchase the Agreement, a simple phone call is all that
it takes for you to schedule service. You can call anytime day or

night, or schedule a service appointment online.
Sears has over 12,000 professional repair specialists, who have

access to over 4.5 million quality parts and accessories. That's
the kind of professionalism you can count on to help prolong the

life of your new purchase for years to come. Purchase your
Master Protection Agreement today[

Some limitations and exclusions apply. For prices and

information call 1-800-827-6655.

The Sears Maintenance Agreement

• Guarantees tomorrow's service at today's price.

• Eliminates repair bills resulting from normal wear and tear.

• Covers non-technical and instructional service calls.

• Provides an annual Preventive Maintenance Check, at your
request, to ensure that your appliance is in proper running

condition.

Some limitations apply. For information concerning Sears

Home Centrar' Maintenance Agreements, call
1-800-361-6665.

Replacement Parts

To order stainless steel cleaner or replacement filters, call

t-800-4MY-HOME e and ask for the appropriate part number
listed below or contact your authorized Kenmore dealer.

Stainless Steel Cleaner & Polish:
Order Part #D22 M40083 R

Base grille water filter cartridges:

Cyst Cartridge:

Order Part #9902 (WF-NLC250 and WF-LC400)

Sears Installation Service
For Sears guaranteed professional installation of home

appliances and items like garage door openers and water
heaters, in the U.S.A. call 1-800-4-MY-HOME ®.

23

WATER FILTER CERTIFICATIONS

s_of_a

l_prm_t ofllcalthS¢_

Water T_atmcnt Device

Ccrti_am Numb_

98-1366

Sm_ofCal_

l_fm_r_ of_ Sc_icsm

WaterTxcstmcntDc_ice

Certificate Numbe_

98- 1367

24

PERFORMANCE DATA SHEETS

Base Grille Water Filtration System Model WF-NLC250/NLC250

42 for the reduction of Chlorine (Class I) Tasteand Odor andagainst
Testedand certified by NSF International againstANSI/NSF Standard
ANSI/NSF Standard 53 for the reduction of Lead, Cysts andTurbidity.

Capacity: 250 Gallons (946 Liters)
Service Flow Rate: 0.5 GPM (189 L/min.) @60 psi.

Substance Reduction U.S. EPA Average Maximum Average Minimum % Average % NSF Test

Aesthetic Effects MCL Influent Effluent Effluent Reduction Reduction Number

Chlorine Taste/Odor N/A 1.9 mg/L N/A 0.04 mg/L N/A 97.9% 994707
Particulate N/A 610,000/mL* N/A 154/mL N/A 99.97% 994711

Contaminant U.S. EPA Average Maximum Average Minimum % Average % NSF Test

Reduction MCL Influent Effluent Effluent Reduction Reduction Number

Cyst 99.95%** 89,250/mL* 6/mL 2.3/mL 99.993% 99.997% 994710
Turbidity 0.5 NTU 29 NTU 0.1 NTU 0.09 NTU 99.5% 99.69% 994710

Lead: @pH 6.5 0.015 mg/L 0.16 mg/L*** 0.001 mg/L 0.001 mg/L 99.4% 99.4% 994708
Lead: @pH 8.5 0.015 mg/L 0.16 mg/L*** 0.002 mg/L 0.001 mg/L 98.8% 99.4% 994709

Base Grille Water Filtration System Model WF-LC4OO/LC400

42 for the reduction of Chlorine (Class I) Taste and Odor and against
Tested and certified by NSF International against ANSI/NSF Standard

ANSI/NSF Standard 53 for the reduction of Lead, Cysts and Turbidity.

Capacity: 400 Gallons (1514Liters)
Service Flow Rate: 0.5 GPM (189 L/min.) @60 psi.

Substance Reduction U.S. EPA Average Maximum Average Minimum % Average % NSF Test

Aesthetic Effects MCL Influent Effluent Effluent Reduction Reduction Number

Chlorine Taste/Odor N/A 2.0 mg/L N/A 0.04 mg/L N/A 98% 994707
Particulate N/A 610,000/mL* N/A 154/mL N/A 99% 994711

Contaminant U.S. EPA Average Maximum Average Minimum % Average % NSF Test _
Reduction MCL Influent Effluent Effluent Reduction Reduction Number _

Cyst 99.95%** 89,250/mL* 6/mL 2.3/mL 99.993% 99.997% 994710
Turbidity 0.5 NTU 29 NTU 0.12 NTU 0.09 NTU 99.59% 99.69% 994710 _

Lead: @pH 6.5 0.015 mg/L 0.16 mg/L*** 0.001 mg/L 0.001 mg/L 99.4% 99.4% 994708
Lead: @pH 8.5 0.015 mg/L 0.16 mg/L*** 0.002 mg/L 0.001 mg/L 98.8% 99.4% 994709

• It is essential that operational, maintenance, and filter • Refer to the front cover or "Assistance or Service" section for _
replacement requirements be carried out for the product to the Manufacturer's name, address and telephone number.

perform as advertised. • Refer to the "Warranty" section for the Manufacturer's limited

• Model WF-NLC250 Change cartridge at least every 6-9 warranty.
months. Use replacement cartridge NLC 250, part# 9902.

2002 suggested retail price of $39.95 U.S.A./S49.95 Canada.
Prices are subject to change without notice.

• Model WF-LC4OO The filter monitor system measures the
amount of water that passes through the filter and alerts you
to replace the filter. When 90% of the filter's rated life is used,
the filter indicator light changes from green to yellow. When

100% of the filter's rated life is used, the filter indicator light
changes from yellow to red, and it is recommended that you
replace the filter. Use replacement cartridge LC400,
part# 9902. 2002 suggested retail price of $39.95 U.S.A./
$49.95 Canada. Prices are subject to change without notice.

• The product is for cold water use only.

• Do not use with water that is microbiologically unsafe or of
unknown quality without adequate disinfection before or after
the system.

Testrequirement is at least 100,000 particles/ml of AC Fine TestDust. Cyst performance is Yoreduction basedon NSF Standard 53. Test
requirement is 0.15 mg/L _ 10%.These contaminants are not necessarily in your water supply. Performancemay vary based on local water conditions.
® NSF is aregistered trademark of NSF International.

+ O

Application Guidelines/Water Supply Parameters

Water Supply City or Well
Water Pressure 30 - 120 psi (207 - 827 kPa)
Water Temperature 33° - 100°F (0,6 ° - 37,8 ° C)

25

Your Home

For repair-in your home-of all major brand appliances,

lawn and garden equipment, or heating and cooling systems,

no matter who made it, no matter who sold it!

For the replacement parts, accessories and

owner's manuals that you need to do-it-yourself.

For Sears professional installation of home appliances

and items like garage door openers and water heaters.

1-800-4-MY-HOME ® (1-800-469-4663)

Call anytime, day or night (U.S.A. and Canada)

www.sears.com www.sears.ca

Our Home

For repair of carry-in items like vacuums, lawn equipment,

and electronics, call or go on-line for the location of your nearest

Sears Parts & Repair Center.

1-800-488-1222

To purchase a protection agreement on a product serviced by Sears:

Para pedir servicio de reparaci6n

a domicilio, y para ordenar piezas:

iiiiiiiiiiiiii,

2220693

© Sears, Roebuck and Co.

Call anytime, day or night (U.S.A. only)

www.sears.com

1-800-827-6655 (U.S.A.) 1-800-361-6665 (Canada)

Au Canada pour service en frangais:

1-800-LE-FOYER Mc

1-888-SU-HOGAR sM

(1-888-784-6427)

(1-800-533-6937)

www.sears.ca

SEARS

® Registered Trademark / Trademark / Service Mark of Sears, Roebuck and Co.

® Marca RegBtrada / Marca de Fabnca / Marca de Servlclo de Sears, Roebuck and Co.

Me MD

Marque de commerce / Marque d6pos6e de Sears, Roebuck and Co.

TM SM

TM , , SM ,

5/02

Printed in U.S.A.

Impreso en EE. UU.

Imprim_ aux E.-U.