Kenmore 10651173310 Use & Care Manual

Use & Care Guide
Manual de uso y cuidado

Guide d'utilisation et d'entretien

English / Espafiol / Fran_ais

Models/Modelos/Mod_les: 106.5117"

I(enmore Elite

,,:,:,:color numbe_, n@nero de colo_, le num@o de la couleur

P/N W10508668B
Sears Brands Management Corporation

Hoffman Estates, IL, U.S.A. 60179
www.kenmore.com

www.sears.com
Sears Canada Inc.

Toronto, Ontario, Canada M5B 2C3
www.sears.ca

TABLEOF CONTENTS

PROTECTION AGREEMENTS ................................................... 2

WARRANTY ............................................................................. 3

REFRIGERATOR SAFETY......................................................... 4

Proper Disposal of Your Old Refrigerator ....................................5

INSTALLATION INSTRUCTIONS .............................................. 5

Unpack the Refrigerator ..................................................................5

Door Removal, Leveling and Alignment ........................................6

Handle Installation and Removal ...................................................9

Location Requirements ....................................................................10

Electrical Requirements ..................................................................10

Water Supply Requirements .........................................................10

Connect Water Supply ....................................................................11

Prepare the Water System ............................................................ 13

Install CleanFIow TM Air Filters .......................................................14

Install CrisperKeeper TM Produce Preserver .................................15

REFRIGERATOR USE.............................................................. 16

Ensuring Proper Air Circulation ..................................................... 16

Using the Controls ...........................................................................16

Water and Ice Dispensers.............................................................18

Water Filtration System................................................................. 21

Ice Maker and Storage Bin...........................................................22

REFRIGERATOR FEATURES.................................................... 23

Refrigerator Door Bins................................................................... 23

Bottle/Can Rack ............................................................................. 23

Refrigerator Shelves........................................................................23

Wine Rack ........................................................................................ 23

Dell Drawer ..................................................................................... 24

Convertible Vegetable/Meat Drawer, Crisper and Covers... 24
Convertible Vegetable/Meat Drawer

Temperature Control ..................................................................... 24

Crisper Humidity Control ...............................................................25

Utility Bin ...........................................................................................25

FREEZER FEATURES............................................................... 25

Freezer Door Bins............................................................................25

Freezer Shelf .................................................................................... 25

Freezer Bin........................................................................................25

REFRIGERATOR CARE ........................................................... 26

Cleaning ............................................................................................26

Lights................................................................................................. 27

Power Interruptions ........................................................................27

Vacation and Moving Care ......................................................... 27

PROBLEM SOLVER ................................................................. 28

ACCESSORIES ........................................................................ 34

WATER FILTER CERTIFICATIONS .......................................... 34

PERFORMANCE DATA SHEET ............................................... 35

SERVICE NUMBERS ............................................. BACK COVER

PROTECTION AGREEMENTS

Master Protection Agreements

Congratulations on making a smart purchase. Your new

Kenmore ® product is designed and manufactured for years of
dependable operation. But like all products, it may require
preventive maintenance or repair from time to time. That's when

having a Master Protection Agreement can save you money and
aggravation.

The Master Protection Agreement also helps extend the life of
your new product. Here's what the Agreement* includes:

1/Parts and labor needed to help keep products operating

properly under normal use, not just defects. Our coverage
goes well beyond the product warranty. No deductibles, no

functional failure excluded from coverage-- real protection.

1/Expert service by a force of more than 10,000 authorized

Sears service technicians, which means someone you can
trust will be working on your product.

I/Unlimited service calls and nationwide service, as often as

you want us, whenever you want us.

JNDICE ................................................................................... 36

TABLE DESMATIERES ............................................................ 72

1/"No-lemon" guarantee - replacement of your covered

product if four or more product failures occur within twelve
months.

1/Product replacement if your covered product can't be fixed.
1/Annual Preventive Maintenance Check at your request - no

extra charge.

I/' Fast help by phone - we call it Rapid Resolution - phone

support from a Sears representative on all products. Think of
us as a "talking owner's manual."

I/Power surge protection against electrical damage due to

power fluctuations.

I/$250 Food Loss Protection annually for any food spoilage

that is the result of mechanical failure of any covered
refrigerator or freezer.

I/Rental reimbursement if repair of your covered product takes

longer than promised.

1/10% discount off the regular price of any non-covered repair

service and related installed parts.

2

Once you purchase the Agreement, a simple phone call is all
that it takes for you to schedule service. You can call anytime

day or night, or schedule a service appointment online.
The Master Protection Agreement is a risk free purchase. If you

cancel for any reason during the product warranty period, we
will provide a full refund. Or, a prorated refund anytime after

the product warranty period expires. Purchase your Master
Protection Agreement today!

I(ENMORE ELITE®LIMITED WARRANTY

Some limitations and exclusions apply. For prices and

additional information in the U.S.A. call 1-800-827-6655.

_Coverage in Canada varies on some items. For full details call

Sears Canada at 1-800-361-6665.

Sears Installation Service

For Sears professional installation of home appliances, garage
door openers, water heaters, and other major home items, in the

U.S.A. or Canada call 1-800-4-MY-HOME ®.

When this appliance is installed, operated and maintained
according to all supplied instructions, the following warranty

coverage applies. To arrange for warranty service, call
1-800-4-MY-HOME _ (1-800-469-4663).

One Year Limited Warranty on Appliance
For one year from the date of purchase, free repair will be

provided if any non-consumable part of this appliance fails due
to defects in material or workmanship. If the appliance is ever

used for other than private family purposes, this coverage
applies for only 90 days from the purchase date.

Five Year Limited Warranty on Sealed System
For five years from the date of purchase, the sealed refrigerant

system of this appliance is warranted against any defects in
material or workmanship. New system components will be

supplied for defective ones free of charge. You are responsible
for the labor cost of component installation after the first year

from the date of purchase. If the appliance is ever used for
other than private family purposes, this coverage applies for

only one year from the purchase date.

Thiswarranty covers only defects in material and
workmanship. Sears will NOT pay for.

1. Consumable parts that can wear out from normal use,
including but not limited to filters, belts, incandescent light

bulbs, and bags.

2. A service technician to instruct the user in correct product
installation, operation or maintenance.

3. A service technician to clean or maintain this product.

4. Damage to or failure of this product if it is not installed,
operated or maintained according to the all instructions

supplied with the product.

5. Damage to or failure of this product resulting from accident,
abuse, misuse or use for other than its intended purpose.

6. Damage to or failure of this product caused by the use of
detergents, cleaners, chemicals or utensils other than those

recommended in all instructions supplied with the product.

7. Damage to or failure of parts or systems resulting from
unauthorized modifications made to this product.

Disclaimer of implied warranties; limitation of remedies
Customer's sole and exclusive remedy under this limited

warranty shall be product repair as provided herein. Implied
warranties, including warranties of merchantability or fitness for

a particular purpose, are limited to one year or the shortest
period allowed by law. Sears shall not be liable for incidental or

consequential damages. Some states and provinces do not
allow the exclusion or limitation of incidental or consequential

damages, or limitation on the duration of implied warranties of
merchantability or fitness, so these exclusions or limitations may

not apply to you.
This warranty applies only while this appliance is used in the

United States or Canada _.
This warranty gives you specific legal rights, and you may also

have other rights which vary from state to state.
_ln Canada, in-home repair service is not available in all areas,

nor will this warranty cover user or servicer travel and
transportation expenses if this product is located in a remote

area (as defined by Sears Canada Inc.) where an authorized
servicer is not available.

Sears Brands Management Corporation

Hoffman Estates, IL 60179

Sears Canada Inc.

Toronto, Ontario, Canada M5B 2C3

PRODUCT RECORD

Record your complete model number, serial number, and
purchase date. You can find this information on the model and

serial number label located on the product.
Have this information available to help you obtain assistance or

service more quickly whenever you contact Sears concerning
your appliance.

Model number

Serial number

Purchase date

Save these instructions and your sales receipt for future
reference.

REFRIGERATORSAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow
instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of fire, electric shock, or injury when using your refrigerator, follow these basic precautions:

[] Plug into a grounded 3 prong outlet.
[] Do not remove ground prong.
[] Do not use an adapter.
[] Do not use an extension cord.

[] Disconnect power before servicing.
[] Replace all parts and panels before operating.
[] Remove doors from your old refrigerator.

SAVE THESE INSTRUCTIONS

[] Use nonflammable cleaner.
[] Keep flammable materials and vapors, such as gasoline,

away from refrigerator.

[] Use two or more people to move and install refrigerator.
[] Disconnect power before installing ice maker (on ice maker

kit ready models only).

[] Use a sturdy glass when dispensing ice (on some models).
[] Do not hit the refrigerator glass doors (on some models).

State of California Proposition 65 Warnings:
WARNING: This product contains one or more chemicals known to the State of California to cause cancer.

WARNING: This product contains one or more chemicals known to the State of California to cause birth defects or other
reproductive harm.

4

Proper Disposal of Your Old Refrigerator

Suffocation Hazard

Remove doors from your old refrigerator.
Failure to do so can result in death or brain damage.

IMPORTANT: Child entrapment and suffocation are not
problems of the past. Junked or abandoned refrigerators are

still dangerous, even if they will sit for "just a few days." If you
are getting rid of your old refrigerator, please follow these

instructions to help prevent accidents.

Before You Throw Away Your Old Refrigerator or Freezer..

• Take off the doors.

• Leave the shelves in place so that children may not easily
climb inside.

important information to know about disposal of
refrigerants:

Dispose of refrigerator in accordance with Federal and Local
regulations. Refrigerants must be evacuated by a licensed,

EPA certified refrigerant technician in accordance with
established procedures.

INSTALLATION INSTRUCTIONS

r

Excessive Weight Hazard

Use two or more people to move and install
refrigerator.

Failure to do so can result in back or other injury.

Remove the Packaging

Remove tape and glue residue from surfaces before turning
on the refrigerator. Rub a small amount of liquid dish soap
over the adhesive with your fingers. Wipe with warm water

and dry.
Do not use sharp instruments, rubbing alcohol, flammable

fluids, or abrasive cleaners to remove tape or glue. These
products can damage the surface of your refrigerator. For

more information see "Refrigerator Safety."

Clean Before Using

After you remove all of the packaging materials, clean the
inside of your refrigerator before using it. See the cleaning

instructions in "Refrigerator Care."

important information to know about glass shelves
and covers:

Do not clean glass shelves or covers with warm water when
they are cold. Shelves and covers may break if exposed to

sudden temperature changes or impact, such as bumping.
Tempered glass is designed to shatter into many small,
pebble-size pieces. This is normal. Glass shelves and covers
are heavy. Use both hands when removing them to avoid

dropping.

When Moving Your Refrigerator:
Your refrigerator is heavy. When moving the refrigerator for

cleaning or service, be sure to cover the floor with
cardboard or hardboard to avoid floor damage. Always pull

the refrigerator straight out when moving it. Do not wiggle or
"walk" the refrigerator when trying to move it, as floor

damage could occur.

Gathertherequiredtoolsandpartsandreadallinstructionsbeforestartinginstallation.Savetheseinstructionsforfuturereference.
NOTE:Beforemovingyourproductintoyourhome,measurethedoorwayofyourhometoseewhetheryouneedtoremovethe

refrigeratorandfreezerdoors.Ifdoorremovalisnecessary,seetheinstructionsbelow.
IMPORTANT:Beforeyoubegin,turntherefrigeratorcontrolOFForturncoolingoff.Unplugrefrigeratorordisconnectpower.

Removefood,theicestoragebin(onsomemodels),andanyadjustabledoororutilitybinsfromdoors.

TOOLS NEEDED:
Bubble level, Phillips screwdriver, _6" hex key, 1/4"hex-head socket wrench, 1/4"and %d' open-ended wrenches or adjustable wrench,

internal star drive or 3/8"hex-head socket wrench

Electrical Shock Hazard

Disconnect power before removing doors.
Failure to do so can result in death or electrical shock.

A B C D E F

A. P-clamp D. Wiring Clip
B. Routing E. Grommets

Plate F. Wiring

C. Electrical Plugs

Housing

Water Dispenser
Tubing Connection
(Style 1)

A

Top Left Hinge

A. Do Not Remove Screws.

Door Removal

Top Right Hinge

A. Do Not Remove Screws.

Bottom Hinges

(Left and Right)

Leveling

A

A. Face of Fitting

Water Dispenser Tubing
Connection (Style 2)

6

A. Bottom Hinge
B. Leveler Bracket

C. Leveling Foot

Door Alignment

(Bottom Right Hinge)

A___IF Raise

A.Alignment Screw

Remove the Doors

Electrical Shock Hazard

Disconnect power before removing doors.
Failure to do so can result in death or electrical shock.

.

Unplug refrigerator or disconnect power.

2.

Open both doors to 90 °. Remove the base grille by
removing the two screws, then pulling out on the outside
corners. See Graphic 7.

NOTE: The doors must only be opened to 90 °. If they are
opened all the way, the base grille will not come off.

.

Disconnect the water tubing, located behind the base grille
on the freezer door side. The dispenser tubing runs through

the door hinge, and must be disconnected in order to
remove the door.

• Style I" Press the colored outer ring against the face of
fitting and pull the water tubing free. See Graphic 2A.

NOTE= Keep the water tubing connector attached to the
tube that runs underneath the freezer. The door cannot

be removed if the connector is still attached to the tube
that runs through the door hinge.

• Style 2= Firmly pull on the clasp to release the tube, then
pull the water tubing free. See Graphic 2B.

NOTE= Keep the clasp attached to the tube that runs
underneath the freezer.

4.

Disconnect the wiring, located behind the base grille on the
freezer door side. See Graphic 3.

• Remove the P-clamp using a 1/4" hex-head socket
wrench. Remove the small wiring bundle from the
P-clamp.

• Remove the wiring clip using a 1/4" hex-head socket

wrench.

• Pull the electrical housing out from under the
refrigerator. Disconnect the wiring plugs from the

housing.

• Gently pull the large wiring bundle (with two white
plugs) through the routing plate.

5. Close both doors and keep them closed until you are ready
to lift them free from the cabinet.

6. Use a 3A6" hex key to remove the top left hinge screws as
shown. See Graphic 4.

IMPORTANT= Do not remove either screw A.

Excessive Weight Hazard

Use two or more people to lift the freezer door.
Failure to do so can result in back or other injury.

7.

Lift freezer door straight up off bottom hinge. See

Graphic 5..The water tubing and wiring remain attached to

the freezer door and pull through the bottom left hinge.
NOTE: This may require two people - one to lift the door

and another to feed the water tubing and wiring through the
hinge. Be sure the hole in the hinge is clear of obstructions,

then gently pull one water tube through the hinge. (Avoid
kinking the tube.) Next, gently pull the other water tube

through the hinge, again avoiding kinks. Finally, gently pull
the wiring bundle (including the grommet and wiring plugs)

through the hinge.
IMPORTANT= Rest the door on its side on a soft, clean

surface, such as a towel, blanket or piece of cardboard. This
will help avoid damaging the door, water tubing and wiring.

8°

Use a 3/_6"hex key to remove the top right hinge screws as
shown. See Graphic 6.

IMPORTANT= Do not remove either screw A.

°

Lift the refrigerator door straight up off bottom hinge.
IMPORTANT= Rest the door on its side on a soft, clean

surface, such as a towel, blanket or piece of cardboard. This
will help avoid damaging the door.

10.

It may not be necessary to remove the bottom hinges to

move the refrigerator through a doorway. Both bottom
hinges have similar construction.

• If necessary, use an internal star drive or a 3/8"hex-head

socket wrench to remove the bottom hinges. See

Graphic 7.

IMPORTANT" The leveler brackets are mounted behind

the hinges. If you remove the hinges, make sure that the

leveler brackets are replaced when reinstalling the
hinges.

Replace the Doors and Hinges

1. Replace both bottom hinges, if removed. Make sure that the

leveler brackets are assembled behind the hinges. Tighten
screws.

IMPORTANT: When the screws are tightened properly, there
should not be any gaps between the refrigerator, leveler
bracket and hinge.

NOTE: There are two wiring bundles that run underneath the
freezer - a large bundle with a large grommet and two white

plugs at the end, and a small bundle with a small grommet and
one yellow plug at the end.

r

Excessive Weight Hazard

Use two or more people to lift the freezer door.
Failure to do so can result in back or other injury.

2.

Before replacing the freezer door on the bottom left hinge,
feed the small wiring bundle through the hinge. Assistance

may be needed.
IMPORTANT: Do not feed the large wiring bundle through

the hinge. This bundle is intended to run directly from the
door to the connections beneath the freezer. Forcing the

large bundle through the hinge may damage the door and/
or the wiring, and will keep the door from closing properly.

3. Feed both water tubes through the bottom left hinge, then
replace the freezer door on the hinge. Assistance may be

needed.

NOTE: Provide additional support for the doors while the top
hinges are being replaced. Do not depend on the door magnets
to hold the doors in place while you are working.

4. Align and replace the top left hinge as shown. See

Graphic 4. Tighten screws.

5. Reconnect water tubing and wiring.

IMPORTANT; Do not intertwine the water tubing and wiring
bundles when reconnecting them.

• Water Connection Style 1: Push the larger 5/_6" (7.94 mm)

water tube into the blue fitting until it stops, then push
the smaller 1/4" (6.35 mm) water tube into the green

fitting until it stops. See Graphic 2.4.
Water Connection Style 2. Push the black water tube

with the blue tip into the blue fitting until it stops. Close
the clasp around the tubing, making sure it snaps into

place. Repeat this process to connect the red-tipped
black water tube and the red fitting. See Graphic 2B.

• Reinstall the P-clamp around the small wiring bundle

(with one yellow plug), then replace the P-clamp on the
top screw hole of the routing plate. See Graphic 3.

• Gently route the large wiring bundle (with two white

plugs) through the hole in the routing plate, so that the
wiring runs behind the right side of the routing plate. See

Graphic 3.

NOTE" The large wiring bundle should always remain
below the small wiring bundle.

• Reconnect the wiring plugs to the electrical housing, then
push the housing back under the refrigerator. Align the

left hole in the front lip of the housing with the right hole

in the refrigerator's base crossbar. See Graphic 3.

• Reinstall the wiring clip over the grommets. First install

the smaller grommet into the top of the clip, then install
the larger grommet into the bottom of the clip (closest to

the screw hole). See Graphic 3.

• Align the clip's screw hole with the left hole in the

electrical housing and the right hole in the crossbar, and
screw in the clip using a single screw. Tighten screw. See

Graphic 3.

IMPORTANT" Once connected, the wiring bundles

should not be taut. Some flexibility is needed to allow
the freezer door to open properly.

6.

Replace the refrigerator door by lifting the door onto the
bottom right hinge.

7.

Align and replace the top right hinge as shown. See

Groph/c 6. Tighten screws.

8.

Replace the ice storage bin (on some models) and any
adjustable door or utility bins.

9.

Plug refrigerator into a grounded 3 prong outlet.

Levelingand Door Closing

Your refrigerator has two adjustable front feet -- one on the
right and one on the left. In most cases, the refrigerator should

be steady when both feet are touching the floor. If your
refrigerator seems unsteady or if you want the doors to close

more easily, adjust the refrigerator's tilt using the instructions
below:

1. Move the refrigerator into its final location. If necessary,
open both doors to 90 ° and remove the base grille. See

Graphic 1.

2. The two leveling feet are located on the brackets on each
side of the product. See Graphic 8.

NOTE: Having someone push against the top of the refrigerator
takes some weight off the leveling feet. This makes it easier to
make adjustments.

3. Use a 1/4"open-ended or adjustable wrench to adjust the
leveling feet. Turn the leveling foot to the left to raise that

side of the product, or turn it to the right to lower that side of
the product.

4. Open both doors again and check that they close as easily
as you like. If not, tilt the refrigerator slightly more to the

rear by turning the leveling feet to the left. It may take
several more turns, and you should turn both leveling feet

the same amount.

5. Use a bubble level to check the leveling of the refrigerator.

NOTE: Whenever you need to move the refrigerator, turn the
leveling feet to the right until they are no longer touching the

ground. This will allow the refrigerator to roll more easily.

Door Alignment

A refrigerator that is not level from side-to-side may appear to
have doors that are not properly aligned. If the doors appear

this way, use the instructions in the previous section to check the
leveling.

The doors are designed to be slightly different heights when the
refrigerator is empty, in order to account for the weight of food

that will be placed on the doors. If the doors are still not aligned
after checking the leveling and loading the refrigerator with

food, follow the steps below to adjust the door alignment.

1. If necessary, open both doors to 90 ° and remove the base
grille. See Graphic I.

2. Locate the alignment screw on the bottom hinge of the
refrigerator door. See Graphic 9.

3. Use a 5/_6" open-ended or adjustable wrench to turn the
screw. To raise the refrigerator door, turn the screw to the
right. To lower the door, turn the screw to the left.

4. Check that the doors are even at the top. If necessary,
continue to turn the alignment screw until the doors are

aligned.

5. Open both doors to 90 °. Replace the base grille. See

Graphic I.

PARTSINCLUDED= Door handles (2), 1/8" hex key, spare
setscrew(s)

To Install the Handles:
NOTE= The handle mounting setscrews are preinstalled in the

handle.

Remove the handles, which are packed inside the
refrigerator.

NOTE= To avoid scratching the finish, place the handles on a
towel or other soft surface.

2. Open the freezer door. On the refrigerator door, place the
handle on the shoulder screws with the setscrews facing the

freezer.

3. Firmly push the handle toward the door until the handle
base is flush against the door.

4. While holding the handle, insert the short end of the hex key
into the upper hole and slightly rotate the hex key until it is

engaged in the setscrew.

7

!i!liiilili

.

Using a clockwise motion, tighten the setscrew until it begins
to contact the shoulder screw.

6.

Repeat steps 4 and 5 to begin fastening the lower setscrew.

7.

Once both setscrews have been partially tightened as
outlined in the previous steps, fully tighten both the upper

and lower setscrews.
IMPORTANT= When the screws feel tight, tighten them an

additional quarter-turn. The handle is not properly installed
without this extra tightening.

8°

Open the refrigerator door and close the freezer door.
Repeat steps 2 through 7 to install the other handle onto the

freezer door with the setscrews facing the refrigerator.

°

Save the hex key and all instructions.

To

Remove the Handles:

1.

While holding the handle, insert the short end of the hex key
into the lower setscrew hole and slightly rotate the hex key

until it is engaged in the setscrew.

2°

Using a counterclockwise motion, loosen the setscrew a
quarter-turn at a time.

3.

Repeat steps 1and 2 for the upper setscrew. Gently pull the
handle away from the door.

4.

If necessary, use a Phillips screwdriver to remove the

shoulder screws from the door.

A

A. Shoulder screws

B. Setscrews inside the handle

Explosion Hazard

Keep flammable materials and vapors, such as
gasoline, away from refrigerator.

Failure to do so can result in death, explosion, or fire.

IMPORTANT= This refrigerator is designed for indoor household
use only.

To ensure proper ventilation for your refrigerator, allow for 1/2"
(1.27 cm) of space on each side and at the top. Allow for 1"
(2.54 cm) of space behind the refrigerator. If your refrigerator

has an ice maker, allow extra space at the back for the water
line connections. When installing your refrigerator next to a

fixed wall, leave a 2" (5.08 cm) minimum space on each side
(depending on your model) to allow the doors to swing open.

/

2" (5.08 crn)

Electrical Shock Hazard

Plug intoa grounded 3 prong outlet.
Do not remove ground prong.

Do not use an adapter.
Do not usean extension cord.

Failureto follow these instructions can result in death,

fire, or electrical shock.

Before you move your refrigerator into its final location, it is
important to make sure you have the proper electrical

connection.

Recommended Groundin 9 Method

A 115 volt, 60 Hz, AC only, 15- or 20-amp fused, grounded
electrical supply is required. It is recommended that a separate

circuit serving only your refrigerator be provided. Use an outlet
that cannot be turned off by a switch. Do not use an

extension cord.
NOTE= Before performing any type of installation or cleaning, or

removing a light bulb, turn cooling off or turn the control
(Thermostat, Refrigerator or Freezer Control depending on the

model) to OFF, and then disconnect the refrigerator from the
electrical source. When you are finished, reconnect the

refrigerator to the electrical source and turn cooling on or reset
the control (Thermostat, Refrigerator or Freezer Control

depending on the model) to the desired setting. See "Using the
Controls" in the User Instructions, User Guide, or Use & Care

Guide.

NOTES=

This refrigerator is intended for use in a location where the
temperature ranges from a minimum of 55°F (13°C) to a
maximum of 110°F (43°C). The preferred room temperature

range for optimum performance, which reduces electricity
usage and provides superior cooling, is between 60°F (15°C)

and 90°F (32°C). It is recommended that you do not install
the refrigerator near a heat source, such as an oven or

radiator.
Normal minimum cabinet cut-out width required for product

installation is 36" (91.44 cm). However, if the product is
placed against an extended wall and the ability to remove

the crisper pans is desired, an additional 18" (45.72 cm) of
cabinet width is required, so a total cabinet opening width

of 54" (137.16 cm) is recommended.

10

Gather the required tools and parts before starting installation.
Read and follow the instructions provided with any tools listed

here.

TOOLS NEEDED:

• Flat-blade screwdriver • 1/4"Nut driver

• 7/_6"and 1/2"Open-end or two • 1/4"Drill bit
adjustable wrenches

NOTE= Your refrigerator dealer has a kit available with a 1¼,,
(6.35 ram) saddle-type shutoff valve, a union, and copper
tubing. Before purchasing, make sure a saddle-type valve

complies with your local plumbing codes. Do not use a piercing-
type or 316" (4.76 mm) saddle valve which reduces water flow

and clogs more easily.

• Cordless drill

IMPORTANT:

• All installations must meet local plumbing code
requirements.

• Use copper tubing and check for leaks. Install copper tubing
only in areas where the household temperatures will remain

above freezing.

Water Pressure

A cold water supply with water pressure of between 30 and
120 psi (207 and 827 kPa) is required to operate the water

dispenser and ice maker. If you have questions about your water
pressure, call a licensed, qualified plumber.

• If your refrigerator has a water dispenser. After installation
is complete, use the water dispenser to check the water

pressure.

• With the water filter removed, dispense 1 cup (237 mL)

of water. If 1 cup of water is dispensed in 8 seconds or
less, the water pressure to the refrigerator meets the

minimum requirement.

• If it takes longer than 8 seconds to dispense 1cup of

water, the water pressure to the refrigerator is lower
than recommended. See "Problem Solver" for

suggestions.

Reverse Osmosis Water Supply
IMPORTANT: The pressure of the water supply coming out of a

reverse osmosis system going to the water inlet valve of the
refrigerator needs to be between 30 and 120 psi (207 and

827 kPa).
If a reverse osmosis water filtration system is connected to your

cold water supply, the water pressure to the reverse osmosis
system needs to be a minimum of 40 to 60 psi (276 to 414 kPa).

If the water pressure to the reverse osmosis system is less than
40 to 60 psi (276 to 414 kPa).

• Check to see whether the sediment filter in the reverse
osmosis system is blocked. Replace the filter if necessary.

Allow the storage tank on the reverse osmosis system to refill
after heavy usage.

If your refrigerator has a water filter, it may further reduce
the water pressure when used in conjunction with a reverse
osmosis system. Remove the water filter. See "Water

Filtration System" in the User Instructions, User Guide, or
Use & Care Guide.

Read all directions before you begin.
IMPORTANT."

• Plumbing shall be installed in accordance with the
International Plumbing Code and any local codes and

ordinances.
The gray water tubing on the back of the refrigerator (which

is used to connect to the household water line) is a PEX
(cross-linked polyethylene) tube. Copper and PEX tubing

connections from the household water line to the refrigerator
are acceptable, and will help avoid off-taste or odor in your

ice or water. Check for leaks.

• Install tubing only in areas where temperatures will remain

above freezing.

TOOLS NEEDED"

Gather the required tools and parts before starting installation.

• Flat-blade screwdriver

• 7/%, and 1/2"open-end wrenches or two adjustable wrenches

• 1/4" nut driver

Connect to Water Line

IMPORTANT= If you turn the refrigerator on before the water

line is connected, turn the ice maker OFF.

Style 1 (Recommended)

1. Unplug refrigerator or disconnect power.

2. Turn OFF main water supply. Turn ON nearest faucet long

enough to clear line of water.

3. Use a quarter-turn shutoff valve or the equivalent, served by

a 1/2"copper household supply line.
NOTE: To allow sufficient water flow to the refrigerator, a

minimum 1_,,size copper household supply line is
recommended.

If you have questions about your water pressure, call a licensed,
qualified plumber.

D

C. Copper tubing (to refrigerator)

D. Household supply line (7/2 "minimum)

11

4.

Now you are ready to connect the copper tubing to the
shutoff valve. Use 1/4"(6.35 mm) OD soft copper tubing to

connect the shutoff valve and the refrigerator.

• Ensure that you have the proper length needed for the
job. Be sure both ends of the copper tubing are cut

square.

• Slip compression sleeve and compression nut onto
copper tubing as shown. Insert end of tubing into outlet

end squarely as far as it will go. Screw compression nut
onto outlet end with adjustable wrench. Do not

overtighten.

A. Compression sleeve

B. Compression nut

.

Place the free end of the tubing into a container or sink, and

C. Copper tubing

turn on main water supply to flush out tubing until water is
clear. Turn off shutoff valve on the water pipe.

NOTE: Always drain the water line before making the final
connection to the inlet of the water valve, to avoid possible

water valve malfunction.

6.

Bend the copper tubing to meet the water line inlet, which is
located on the back of the refrigerator cabinet as shown.

Leave a coil of copper tubing to allow the refrigerator to be
pulled out of the cabinet or away from the wall for service.

Style 2

1. Unplug refrigerator or disconnect power.

2. Turn OFF main water supply. Turn ON nearest faucet long
enough to clear line of water.

3. Locate a 1/2"(1.27 cm) to 11/4'' (3.18 cm) vertical cold water
pipe near the refrigerator.

IMPORTANT:

Make sure it is a cold water pipe.
Horizontal pipe will work, but drill on the top side of the

pipe, not the bottom. This will help keep water away
from the drill and normal sediment from collecting in the

valve.

4.

Determine the length of copper tubing you need. Measure
from the connection on the lower rear corner of refrigerator

to the water pipe. Add 7 ft (2.1 m) to allow for cleaning. Use
1/4"(6.35 mm) O.D. (outside diameter) copper tubing. Be

sure both ends of copper tubing are cut square.

.

Using a cordless drill, drill a 1/4" (6.35 mm) hole in the cold
water pipe you have selected.

G _\_A

A. Cold water pipe

B. Pipe clamp

C. Copper tubing
D. Compression nut

E. Compression sleeve
E Shutoff valve

G. Packing nut

6. Fasten the shutoff valve to the cold water pipe with the pipe

clamp. Be sure the outlet end is solidly in the 1/4"(6.35 mm)
drilled hole in the water pipe and that the washer is under
the pipe clamp. Tighten the packing nut. Tighten the pipe
clamp screws slowly and evenly so the washer makes a

watertight seal. Do not overtighten, or you may crush the
copper tubing.

7. Slip the compression sleeve and compression nut on the
copper tubing as shown. Insert the end of the tubing into the

outlet end squarely as far as it will go. Screw the
compression nut onto outlet end with adjustable wrench. Do

not overtighten.

8. Place the free end of the tubing in a container or sink, and
turn ON the main water supply. Flush the tubing until water

is clear. Turn OFF the shutoff valve on the water pipe. Coil
the copper tubing.

Connect to Refrigerator

Style 1

1. Unplug refrigerator or disconnect power.

2. Remove and discard the short, black plastic part from the
end of the water line inlet.

.

Thread the nut onto the end of the tubing. Tighten the nut by
hand. Then tighten it with a wrench two more turns. Do not

overtighten.
NOTE: To avoid rattling, be sure the copper tubing does not

touch the cabinet's side wall or other parts inside the
cabinet.

A B C O

A. Household water line C. Ferrule (purchased)

B. Nut (purchased) D. Refrigerator water tubing

4.

Install the water supply tube clamp around the water supply

line to reduce strain on the coupling.

5.

Turn shutoff valve ON.

6.

Check for leaks. Tighten any connections (including
connections at the valve) or nuts that leak.

Style 2
I. Unplug refrigerator or disconnect power.

2. Remove and discard the plastic part that is attached to the
inlet of the water valve.

3. Attach the copper tube to the valve inlet using a
compression nut and sleeve as shown. Tighten the

compression nut. Do not overtighten.

4. Use the tube clamp on the back of the refrigerator to secure
the tubing to the refrigerator as shown. This will help avoid

damage to the tubing when the refrigerator is pushed back
against the wall.

5. Turn shutoff valve ON.

12

6.

Check for leaks. Tighten any connections (including
connections at the valve) or nuts that leak.

Complete the Installation

A. Tube clamp

B. Tube clamp screw

C. Copper tubing

D. Compression nut

E. Valve inlet

On some models, the ice maker is equipped with a built-in
water strainer. If your water conditions require a second

water strainer, install it in the 1/4"(6.35 mm) water line at
either tube connection. Obtain a water strainer from your

nearest appliance dealer.

Style 3

1. Unplug refrigerator or disconnect power.

2. Remove and discard the black nylon plug from the gray
water tube on the rear of the refrigerator.

3. If the gray water tube supplied with the refrigerator is not
long enough, a 1/4"x 1/4"(6.35 mm x 6.35 mm) coupling is

needed in order to connect the water tubing to an existing
household water line. Thread the provided nut onto the

coupling on the end of the copper tubing.
NOTE: Tighten the nut by hand. Then tighten it with a

wrench two more turns. Do not overtighten.

A B C D E F G

A. Refrigerator water tubing E. Ferrule {purchased)

B, Nut {provided] E Nut {purchased]

C. Bulb G. Household water line
D, Coupling {purchased]

4. Turn shutoff valve ON.

5. Check for leaks. Tighten any nuts or connections (including
connections at the valve) that leak.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.

Do not use an extension cord.
Failure to follow these instructions can result in death,

fire, or electrical shock.

1. Plug into a grounded 3 prong outlet.

2. Flush the water system. See "Prepare the Water System" or

"Water and Ice Dispensers."

NOTE: Allow 24 hours to produce the first batch of ice. Allow
72 hours to completely fill ice container.

Please read before using the water system.

Immediately after installation, follow the steps below to make

sure that the water system is properly cleaned.

1. Open the freezer door and turn off the ice maker. The On/
Off switch can only be accessed when the ice storage bin

has been removed. The switch is located on the freezer door,
on the left side of the wall that surrounds the ice storage bin.

Move the switch to the OFF (right) setting.

2. Make sure the water filter is properly installed.

Do not use with water that is microbiologically unsafe or
of unknown quality without adequate disinfection before
or after the system. Systems certified for cyst reduction
may be used on disinfected waters that may contain

filterable cysts.

.

Flush the water system. Use a sturdy container to depress
and hold the water dispenser lever for 5 seconds, then

release it for 5 seconds. Repeat until water begins to flow.
Once water begins to flow, continue depressing and

releasing the dispenser lever (5 seconds on, 5 seconds off)
until a total of 3 gal. (12 L) has been dispensed. This will

flush air from the filter and water dispensing system, and
prepare the water filter for use. Additional flushing may be

required in some households. As air is cleared from the
system, water may spurt out of the dispenser.

13

4.

Open the freezer door and turn on the ice maker. Move the
switch to the ON (left) position. Please refer to the "Ice

Maker and Storage Bin" section for further instructions on
the operation of your ice maker.

• Allow 24 hours to produce the first batch of ice.

• Discard the first three batches of ice produced.

• Depending on your model, you may want to select the
maximum ice feature to increase the production of ice.

On some models, your refrigerator's accessory packet includes
two air filters, which must be installed prior to use. On some

models, the air filters are already installed at the factory.

The air filter reduces the buildup of odors. This helps to maintain
a cleaner environment inside the refrigerator.

Installing the Air Filters (on some models)

Location 2.

Install the other filter in the filter housing assembly, which is

located along an interior side wall of the crisper and/or
convertible drawer.

NOTE: There are two housing assemblies. Use one for one of the
CleanFIow TM Air Filters, and use the other for the
CrisperKeeper TM Produce Preserver pouches. Do not install

Air Filters and Produce Preserver pouches in the same housing
assembly. See "Install CrisperKeeper TM Produce Preserver" for
additional information.

1. Remove the air filter from its packaging.

2. Lift up on the housing in order to remove it from its mounting
tab along the wall.

3. Snap the filter into place on the rear of the housing.

The filters should be installed in two separate locations.

Location 1:

Install one of the filters behind the vented door, which is located
(depending on your model) along either the rear or left interior

wall near the top of the refrigerator compartment.

.

Remove the air filter from its packaging.

2.

Lift open the vented door.

3.

Snap the filter into place.

(q

4. Place the housing back on the mounting tab along the wall.

Installing the Filter Status Indicators (on some models)

Each filter comes with a status indicator, which should be
activated and installed at the same time the air filter is installed.

4.

Close the vented door.

14

Location 1:

1. Place the indicator face-down on a firm, flat surface.

2. Apply pressure to the bubble on the back of the indicator,
until the bubble pops to activate the indicator.

3. Lift open the vented air filter door. There are notches behind
the door. Slide the indicator down into the notches, facing

outward.
NOTE. The indicator will not easily slide into the notches if

the rear bubble has not been popped.

4. Close the air filter door, and check that the indicator is
visible through the rectangular hole in the door.

Location 2.

1. Place the indicator face-down on a firm, flat surface.

2. Apply pressure to the bubble on the back of the indicator,
until the bubble pops to activate the indicator.

3. Slide open the cap on the housing assembly.

4. Place the indicator in the top of the housing, facing outward.

5. Slide the cap closed, and check that the indicator is visible
through the rectangular hole in the cap.

NOTE: The cap will not easily close if the indicator's rear
bubble has not been popped.

Apples
Asparagus

Berries
Broccoli

Cantaloupe
Carrots

Citrus Fruit

Grapes
Lettuce

Pears
Spinach

Sensitivity to

Ethylene

High

Med.

Low

High

Med.

Low

Med.

Low

High

High

High

Ethylene

Production

Very High

Very Low

Low

Very Low

High
Very Low
Very Low

Very Low
Very Low

Very High

Very Low

Installingthe Produce Preserver(on some models)

Replacing the Air Filter

The disposable air filter should be replaced every 6 months,
when the status indicator has completely changed from white to

red.
To order a replacement air filter, see "Accessories."

1. Remove the old air filter by squeezing in on the side tabs.

2. Remove the old status indicator.

3. Install the new air filter and status indicator using the
instructions in the previous sections.

On some models, your refrigerator's accessory packet includes
a Produce Preserver, which should be installed prior to use. On

some models, the Produce Preserver is already installed at the
factory.

The Produce Preserver absorbs ethylene, allowing the ripening
process of many produce items to slow down. As a result, certain

produce items will stay fresh longer.
Ethylene production and sensitivity varies depending on the type

of fruit or vegetable. Topreserve freshness, it is best to separate
produce with sensitivity to ethylene from fruits that produce

moderate to high amounts of ethylene.

CAUTION: IRRITANT

MAY IRRITATE EYES AND SKIN. DANGEROUS FUMES
FORM WHEN MIXED WITH OTHER PRODUCTS.

Do not mix with cleaning products containing ammonia,
bleach or acids. Do not get in eyes, on skin or clothing. Do
not breathe dust. Keep out of reach of children.

FIRST AIDTREATMENT: Contains potassium
permanganate. If swallowed, call a Poison Control Center or
doctor immediately. Do not induce vomiting. If in eyes, rinse
with water for 15 minutes. If on skin, rinse with water.

For best performance, always use two Produce Preserver
pouches. Both pouches should be installed in the same housing

assembly, which is located along an interior side wall of the
crisper and/or convertible drawer.

NOTE: There are two housing assemblies. Use one for the
CrisperKeeper TM Produce Preserver pouches, and use the other

for one of the CleanFIow TM Air Filters. Do not install Produce
Preserver pouches and Air Filters in the same housing assembly.

See "Install CleanFIow TM Air Filters" for additional information.

15

Remove the Produce Preserver pouches from their
packaging.

n!rl

Produce, ' re,se vet

CAUTION CUIDADO
IRRITANT IRRITANTE

2. Lift up on the housing in order to remove it from its mounting
tab along the wall.

3. Open the housing by pulling up and out on the back of the
top of the housing.

4. Place both pouches inside the housing, then snap the housing
back together.

5. Place the housing back on the mounting tab along the wall.

Installing the Status Indicator (on some models)

REFRIGERATOR USE

In order to ensure proper temperatures, you need to permit air

to flow between the two sections. Cold air enters the bottom of
the freezer section and moves up. It then enters the refrigerator

section through the top vent. (On Style 2 models, this air is also
evenly distributed throughout the refrigerator compartment

through six vents on the back wall.) Air then returns to the
freezer as shown.

Style 1 Style 2

The Produce Preserver comes with a status indicator, which
should be activated and installed at the same time the pouch is

installed.

1. Place the indicator face-down on a firm, flat surface.

2. Apply pressure to the bubble on the back of the indicator,
until the bubble pops to activate the indicator.

3. Slide open the cap on the Produce Preserver housing.

4. Place the indicator in the top of the housing, facing outward.

5. Slide the cap closed, and check that the indicator is visible
through the rectangular hole in the cap.

NOTE: The cap will not easily close if the indicator's rear
bubble has not been popped.

Replacing the Produce Preserver (on some models)

The disposable pouches should be replaced every 6 months,
when the status indicator has completely changed from white to

red.

To order replacements, see "Accessories."

.

Remove the old pouches from the Produce Preserver
housing.

2.

Remove the old status indicator.

3.

Install the new pouches and status indicator using the

instructions in the previous sections.

Do not block any of these vents with food such as soda, cereal,
bread, etc. If the vents are blocked, airflow will be obstructed
and temperature and moisture problems may occur.

IMPORTANT: Because air circulates between both sections, any
odors formed in one section will transfer to the other. You must

thoroughly clean both sections to eliminate odors. To avoid odor
transfer and drying out of food, wrap or cover foods tightly.

The refrigerator and freezer controls are located on the
dispenser panel.

IMPORTANT: The display screen on the dispenser control panel
will turn off automatically and enter "sleep" mode when the

control buttons and dispenser pad have not been used for
2 minutes or more. While in "sleep" mode, the first press of a

control button will only reactivate the display screen, without
changing any settings.

• Touch any control button on the dispenser panel to activate
the display screen. The home screen will appear as shown.

16

AdjustingtheControls

For your convenience, your refrigerator and freezer controls are
preset at the factory. When you first install your refrigerator,

make sure that the controls are still set to the "mid-settings." The
factory recommended set points are 37°F (3°C) for the
refrigerator and 0°F (-18°C) for the freezer.

IMPORTANT:

Wait 24 hours before you put food into the refrigerator. If
you add food before the refrigerator has cooled completely,

your food may spoil.
NOTE: Adjusting the set points to a colder than

recommended setting will not cool the compartments any
faster.

Press SETTINGS to raise the set point, or press
TEMPERATURE to lower the set point.

When you have finished viewing (and adjusting if desired)
the refrigerator set point, press ACCENT LIGHT to change
the display to show the freezer set point. When the zone has

been changed, "FREEZER" appears on the display screen.
Press SETTINGS to raise the set point, or press

TEMPERATURE to lower the set point.
When you have finished viewing (and adjusting if desired)

both the refrigerator and freezer set points, press LOCI< to
save the settings.

NOTE: To exit without saving changes, press WATER/ICE at
any time while in adjust mode, or allow about 60 seconds of

inactivity and adjust mode will turn off automatically.

When adjusting temperature set points, use the following chart
as a guide.

CONDITION: TEMPERATURE

ADJUSTMENT:

REFRIGERATOR too cold REFRIGERATOR Setting

1° higher

REFRIGERATOR too warm REFRIGERATOR Setting

1° lower

FREEZERtoo cold FREEZERSetting

1° higher

If the temperature is too warm or too cold in the refrigerator

or freezer, first check the air vents to be sure they are not
blocked before adjusting the controls.

The preset settings should be correct for normal household
usage. The controls are set correctly when milk or juice is as

cold as you like and when ice cream is firm.
Wait at least 24 hours between adjustments. Recheck the

temperatures before other adjustments are made.

To view and adjust the set points, press and hold the
TEMPERATURE button for 3 seconds. When adjust mode is

activated, adjusting information will appear on the display
screen.

FREEZERtoo warm / FREEZERSetting
Too little ice 1° lower

The set point range for the refrigerator is 33°F to 45°F (0°C to
7°C). The set point range for the freezer is -5°F to 5°F (-21°C to

-15°C).

Cooling On/Off

Your refrigerator and freezer will not cool when cooling is
turned off.

• To turn cooling off, press and hold the LOCI< and
MEASURED FILL buttons at the same time for 3 seconds.

IMPORTANT: To avoid unintentionally locking the dispenser
or changing other settings, be sure to press both buttons at

exactly the same time.
When cooling is off, "COOLING OFF" will appear on the

display screen.
Press and hold LOCI< and MEASURED FILL for 3 seconds

again to turn cooling back on.

NOTE" To view Celsius temperatures, press the MEASURED FILL
button when adjust mode is activated. To return the display
setting to Fahrenheit, press MEASURED FILL again.

• When adjust mode is activated, the display screen shows
the refrigerator set point and "REFRIGERATOR" appears.

17

Additional Features

Accelerated Ice Production

The Accelerated Ice feature assists with temporary periods of
heavy ice usage by increasing ice production.

IMPORTANT: This feature only works if the ice maker is turned
on. See "Ice Maker and Storage Bin."

• To turn on the feature, press SETTINGS then TEMPERATURE.
When the feature is on, the Accelerated Ice icon will

appear on the dispenser display screen.

- _ Acceler

"=_ Ice

The Accelerated Ice setting will remain on for a minimum of
90 minutes unless manually turned off.

To manually turn off the feature, press SETTINGS then
TEMPERATURE again, or adjust the freezer temperature set

point. The Accelerated Ice icon will disappear when the
feature is off.

NOTE: If increased ice production is desired at all times,
change the freezer set point to a lower setting. Setting the

freezer to a colder temperature may make some foods, such as
ice cream, harder.

Door Ajar Alarm
The Door Ajar Alarm feature sounds an alarm when the

refrigerator or freezer door is open for 5 minutes and the
product cooling is turned on. The alarm will repeat every

2 minutes. Close both doors to turn it off. The feature then resets
and will reactivate when either door is left open again for

5 minutes.
NOTE: To mute the audible alarm while keeping the doors open,

such as while cleaning the inside of the refrigerator, press any
button on the control panel. The alarm sound will be temporarily

turned off, but the Door Ajar icon will still be displayed on the
dispenser control panel.

NOTES:

• The dispensing systemwill not operate when either door
(refrigerator or freezer) is open.

• Allow 24 hours for the refrigerator to cool down and chill
water.

Allow 24 hours to produce the first batch of ice. Discard the
first three batches of ice produced. Wait 72 hours for full

ice production.
The display screen on the dispenser control panel will turn

off automatically and enter "sleep" mode when the control
buttons and dispenser pad have not been used for 2 minutes

or more. While in "sleep" mode, the first press of a control
button will only reactivate the display screen, without

changing any settings.

Flush the Water System

Air in the water dispensing system can cause the water
dispenser to drip. After connecting the refrigerator to a water

source or replacing the water filter, flush the water system.
Flushing the water dispensing system forces air from the water

line and filter, and prepares the water filter for use.
NOTE: As air is cleared from the system, water may spurt out of

the dispenser.

1. Using a sturdy container, depress and hold the water
dispenser pad for 5 seconds, then release it for 5 seconds.

2. Repeat Step 1 until water begins to flow.

3. Once water begins to flow, continue depressing and
releasing the dispenser pad (5 seconds on, 5 seconds off)

until a total of 3 gal. (12 L) has been dispensed.

Additional flushing may be required in some households.

DispensingOptions

Disabling Sounds

• To turn off all dispenser and control sounds, press and hold
WATER/ICE and MEASURED FILL at the same time for
3 seconds.

IMPORTANT: Toavoid unintentionally changing other
settings, be sure to press both buttons at exactly the same

time.
To turn all sounds back on, press and hold WATER/ICE and

MEASURED FILLat the same time for 3 seconds again.

18

Your dispenser can dispense water and ice in two ways.

• The DISPENSE WATER button, located below the dispenser
control panel's display screen, dispenses only water.

• The dispenser pad is the pad located along the rear wall of
the dispenser cavity. When pressed, it dispenses either water
or ice, depending on the chosen setting.

Todispense both water and ice at the same time, select the
desired type of ice and dispense it using the dispenser pad, then

press the DISPENSE WATER button while still dispensing ice.

Calibrate Measured Fill

Household water pressure may affect the accuracy of the
Measured Fill feature. For optimum performance of your water

dispenser, you must first calibrate Measured Fill.
IMPORTANT: Flush the water system before calibrating

Measured Fill.

Place a sturdy measuring cup (1 cup [237 mL] size) on the
dispenser tray, centered in front of the water dispenser pad.

NOTE: Depending on your model, a measuring cup may be
provided.

2. Press and hold the SETTINGS and LOCI( buttons at the

same time for 3 seconds. The words "Back" and "1 Cup" will
appear on the display screen. Also, "CALIBRATION" will

illuminate and remain lit while the Measured Fill feature is
being calibrated.

NOTE: You may press the WATER/ICE button under the
word "Back" at any time to exit calibration mode. The

display screen's "CALIBRATION" text will turn off.

3. Using your hand (not the measuring cup), press and release
the water dispenser pad in order to dispense water to the
1cup fill line.

If it takes longer than 8 seconds to dispense 1 cup of

water, the water pressure to the refrigerator is lower
than recommended. See "Water Supply Requirements"

or "Problem Solver" for suggestions.

To Dispense Water (Standard):
NOTE: While dispensing water and for 3 seconds after

dispensing has stopped, the digital display will show how much
water has been dispensed. The default unit is ounces. To switch

to cups or liters, press the SETTINGS button then press
MEASURED FILLto toggle through the available units.

Option 1.

1. Place a sturdy glass below the dispenser opening.

2. To dispense water, press the DISPENSE WATER button. Hold
the glass close to the water dispenser spout to ensure that

the water dispenses into the glass.

_A

NOTE: If overfilling or spilling occurs, discard the water and
press "Back" to restart the calibration process.

4. When 1cup of water has been correctly dispensed into the
measuring cup, press the MEASURED FILL button under the

word "Confirm" to confirm the calibration.

When Measured Fill calibration has been confirmed, the display
will return to the home screen.

The Water Dispenser

IMPORTANT:

Dispense at least 1qt (1 L)of water every week to maintain a
fresh supply.

If the flow of water from the dispenser decreases, it could be

caused by low water pressure.

With the water filter removed, dispense 1 cup (237 mL)
of water. If 1 cup of water is dispensed in 8 seconds or

less, the water pressure to the refrigerator meets the
minimum requirement.

A. Water dispenser spout

3. To stop dispensing, press the DISPENSE WATER button a
second time.

Option 2;

1. Press the WATER/ICE button until "Water" is selected.

2. Press a sturdy glass against the dispenser pad. Hold the

glass close to the water dispenser spout to ensure that the
water dispenses into the glass.

A. Water dispenser spout

3. Remove the glass to stop dispensing.

19

To Dispense Water (Measured Fill):

Measured Fill allows you to dispense a specified amount of
water with the touch of a few buttons.

NOTE: The amount of water you select will be dispensed. Be
sure that the container is empty and can hold the entire volume.

If ice is in the container, you may need to adjust your selection.
IMPORTANT: Low water pressure may affect the accuracy of

this feature.

1. Press MEASURED FILL to turn the feature on. When the
feature is on, the Measured Fill screen appears on the

display.

Press WATER/ICE to manually turn off the Measured Fill
feature.

NOTE: The dispenser will automatically turn off Measured
Fill after 1minute of inactivity. When Measured Fill is turned

off, any changes you have made will be lost and all defaults
will be restored.

2°

You can dispense water by the ounce, cup, or liter. The
default unit is ounces. To switch to cups or liters while the

Measured Fill feature is already on, press the MEASURED
FILL button to toggle through the available units.

Default, minimum, and maximum volumes are listed below.

Units Default Minimum Maximum

Ounces 8 1 128

Cups 1 1//4 16

Liters 0.25 0.05 4.00

°

Press the SETTINGS and TEMPERATURE buttons to adjust
the volume as desired. The SETTINGS button increases the

volume, and the TEMPERATURE button lowers the volume.
NOTES:

4.

You can save one "favorite" volume for repeated use. Adjust
the settings until the desired volume is displayed, then press

LOCI< to save the volume. In future Measured Fill use, press
LOCI< to access the saved volume setting.

NOTE: You can only save one "favorite." Saving a new
volume will overwrite the previously-saved "favorite."

°

Todispense water, press a sturdy glass against the dispenser
pad OR place the glass below the dispenser opening and
press either the DISPENSE WATER button or the ACCENT

LIGHT button. Hold the glass close to the water dispenser
spout to ensure that the water dispenses into the glass.

....A

A. Water dispenser spout

NOTE" While dispensing water, the digital display will count
down how much water remains to be dispensed, according
to the volume you selected. The flow of water will

automatically stop once the desired volume has been
dispensed.

6°

To stop dispensing before the selected volume has been
dispensed, remove the glass from the dispenser pad OR

press either the DISPENSE WATER button or the ACCENT
LIGHT button a second time.

NOTE: If you stop dispensing before the desired volume has
been dispensed, the digital display will continue to show

how much water remains to be dispensed. The display will
turn off after 1 minute of inactivity.

The Ice Dispenser

Ice dispenses from the ice maker storage bin in the freezer when

the dispenser pad is pressed. To turn off the ice maker, see "Ice
Maker and Storage Bin."

Your ice maker can produce both crushed and cubed ice. Before
dispensing ice, select which type of ice you prefer by pressing

the WATER/ICE button.
The display screen indicates which type of ice is selected.

• When increasing or decreasing the volume of water, the

control may stop responding if an adjustment button is
held for approximately 10 seconds or longer. Release the

button for approximately 2 seconds, then continue
making adjustments.

• Most coffee cups (commonly 4 to 6 oz [118 to 177 mL]

per cup) are not the same size as a measuring cup (8 oz
[237 mL]). You may need to adjust the volume to avoid

unintentionally overfilling coffee cups.

2O

CRUSHED CUBED

For crushed ice, cubes are crushed before being dispensed. This
may cause a slight delay when dispensing crushed ice. Noise

from the ice crusher is normal, and pieces of ice may vary in
size. When changing from crushed to cubed, a few ounces of

crushed ice will be dispensed along with the first cubes.

To Dispense Ice:

1. Make sure the desired type of ice is selected. To switch

between cubed and crushed, press WATER/ICE.

Cut Hazard

Use a sturdy glass when dispensing ice.

Failure to do so can result in cuts.

2. Press a sturdy glass against the dispenser pad. Hold the
glass close to the ice guide to ensure that the ice dispenses

into the glass.

• PressACCENT LIGHT a second time to turn the dispenser
pad light off.

The dispenser lights are LEDsthat cannot be changed. If it
appears that your dispenser lights are not working, see "Problem

Solver" for more information.

The Dispenser Lock

The dispenser can be turned off for easy cleaning or to avoid
unintentional dispensing by small children and pets.

NOTE= The lock feature does not shut off power to the
refrigerator, to the ice maker, or to the dispenser light. It simply
deactivates the controls and dispenser pad. To turn off the ice

maker, see "Ice Maker and Storage Bin."

• Press and hold LOCI< for 3 seconds to lock the dispenser.

• Press and hold LOCI< a second time to unlock the dispenser.
The display screen indicates when the dispenser is locked.

A. Ice guide

IMPORTANT= You do not need to apply a lot of pressure to
the pad in order to activate the ice dispenser. Pressing hard
will not make the ice dispense faster or in greater quantities.

NOTE= To dispense both water and ice at the same time,
press the DISPENSE WATER button while using the dispenser

pad to dispense ice.

.

Remove the glass to stop dispensing.
NOTE= Ice may continue to dispense for several seconds

after removing the glass from the pad. The dispenser may
continue to make noise for a few seconds after dispensing.

The Dispenser Ucjht

The dispenser has two separate lights: a white dispenser light
and a blue dispenser pad light.

The white dispenser light automatically turns on when you use
the dispenser, then turns off when dispensing stops.

The blue dispenser pad light can be manually turned on or off.

• Press the ACCENT LIGHT button to turn the dispenser
pad light on. The display screen indicates when the light

is on.

Do not use with water that is microbiologically unsafe or
of unknown quality without adequate disinfection before
or after the system. Systems certified for cyst reduction
may be used on disinfected waters that may contain

filterable cysts.

Water Filter Status Ucjht

The water filter status light will help you know when to change
your water filter.

• When the dispenser control panel's water filter status
display changes to "ORDER," this tells you that it is almost

time to change the water filter cartridge.
Replace the water filter cartridge when the water filter

status display changes to "REPLACE."
NOTE= If water flow to your water dispenser or ice maker

decreases noticeably, change the filter sooner. The filter
should be replaced at least every 6 months, depending on

your water quality and usage.

You can check the remaining life of your water filter at any time.

• Press SETTINGS, then press SETTINGS again. The display
screen will show how many more gallons of water the filter

can effectively filter. Press WATER/ICE to exit the filter

status screen.

NOTE= A new filter's "Gallons Remaining" display is 200.
The "ORDER" status begins at 40 gal. (151L) remaining, and

the "REPLACE" status activates when the filter has 0 gal.
remaining.

21

Resetting the Filter Status

• After changing the water filter, reset the status light. Press
and hold TEMPERATURE and SETTINGS at the same time

for 3 seconds.
IMPORTANT: To avoid unintentionally changing other

settings, be sure to press both buttons at exactly the same
time.

When the system is reset, the "ORDER" and "REPLACE"
icons will disappear from the display screen.

NOTE: When the status displays "REPLACE," you can
temporarily reset the status icon manually, without changing the

water filter. Press and hold the ACCENT LIGHT and
TEMPERATURE buttons at the same time for 3 seconds. The

"REPLACE" display will be turned off for 14 days. When it turns
back on, you can manually reset it again if desired.

Changing the Water Filter

.

Locate the water filter in the top-right corner of the
refrigerator compartment.

2.

Lift open the filter cover door. The filter will be released and
then be ejected as the door is opened.

3.

When the door is completely open, pull the filter straight
out.

NOTE: There may be some water in the filter. Some spilling
may occur. Use a towel to wipe up any spills.

4.

Take the new filter out of its packaging and remove the
covers from the O-rings. Be sure the O-rings are still in place

after the covers are removed.

5. With the arrow pointing up, align the new filter with the
filter housing and slide it into place. The filter cover door will
automatically begin to close as the new filter is inserted.

6. Close the filter cover door completely in order to snap the
filter into place. You may need to press hard.

7. Flush the water system. See "Water and Ice Dispensers."

Do not use anything sharp to break up the ice in the storage
bin. This can cause damage to the ice container and the

dispenser mechanism.
Do not store anything on top of or in the ice maker or

storage bin.

Turningthe Ice Maker On/Off

The On/Off switch can only be accessed when the ice storage
bin has been removed. The switch is located on the freezer door,

on the left side of the wall that surrounds the ice storage bin.
See the following section for bin removal instructions.

EEl

On Off

Ice Maker Control

To turn on the ice maker, slide the control to the ON (left)
position.

To manually turn off the ice maker, slide the control to the
OFF (right) position.

NOTE: The ice maker has an automatic shutoff to keep the
storage bin from overfilling during normal operation. The ice

maker sensors will automatically stop ice production, but the
control will remain in the ON (left) position.

Removing and Replacing the Ice Storage Bin

1. Pressdown the release lever and tilt the bucket outward. Use

both hands to hold the base of the storage bin, then lift it up
and out.

sSxs ' , <3eB

Allow 24 hours to produce the first batch of ice. Discard the
first three batches of ice produced.

The quality of your ice will be only as good as the quality of
the water supplied to your ice maker. Avoid connecting the

ice maker to a softened water supply. Water softener
chemicals (such as salt) can damage parts of the ice maker

and lead to poor quality ice. If a softened water supply
cannot be avoided, make sure the water softener is

operating properly and is well maintained.

22

A. Release lever

NOTE: It is not necessary to turn the ice maker control to the
OFF (right) position when removing the storage bin. The _;_@_r_ _/_";_._.G_'_R_gidi_
sensor cover ("flipper door"), located on the right wall of the (oY__;_:e_'_e_e_;_e:_

freezer door, stops the ice maker from producing ice if the
door isopen or the storage bin is removed. To Remove and Replace the Bottle/Can Rack.

2. Replace the bottle/can rack by sliding it in above the

/ !it .-- o,onro n on pUn ro+ou

desired supports and pushing it down until it stops.

........ lii ..............

B.Sensorcover 'S_3_gSb@_: e7<_seves _/6_' es I_symede

2.

Replace the bin by sliding it onto the door, then tilting it
back into an upright position. The release lever will click

when the bin is securely in place.

REFRIGERATOR FEATURES

Your model may have some or all of these features. Features
that can be purchased separately as product accessories are

labeled with the word "Accessory." Not all accessories will fit all
models. If you are interested in purchasing one of the

accessories, please call the toll-free number on the back cover
or in the "Accessories" section.

Store similar foods together and adjust the shelves to fit
different heights. This reduces the time the refrigerator door is

open and saves energy.

To Remove and Replace a Shelf..

1. Pullthe shelf forward to the stop. Tilt the front of the shelf up

and lift it slightly as you pull the shelf from the frame.

2.

Replace the shelf by guiding it back into the slots on the
frame and pushing the shelf in past the stop.

k

Important information to know about glass shelves
and covers:

Do not olean glass shelves or oovers with warm water when
they are oold. Shelves and oovers may break if exposed to
sudden temperature ohanges or impaot, suoh as bumping.

Tempered glass is designed to shatter into many small,

pebble-size pieoes. This is normal. Glass shelves and oovers
are heavy. Use both hands when removing them to avoid
dropping.

(e_ some modes}

To Remove and Replace the Bins..

1. Remove the bin by lifting it and pulling it straight out.

2. Replace the bin by sliding it in above the desired supports
and pushing it down until it stops.

/ \

Wse Rack

(os'ssome modes}

The wine rack can be placed on any set of refrigerator shelf
supports, either with (as shown below) or without a shelf on the
same supports.

I

NOTE: If the wine rack is sharing a set of supports with a shelf,
you must first remove the shelf in order to remove the wine rack.

23

(o_} som_;! models)

The dell drawer stores raisins, nuts, spreads, and other small
items at normal refrigerator temperatures.

To Remove and Replace the Dell Drawer:

1. Remove the dell drawer by sliding it straight out to the stop.
Lift the front and slide the drawer out the rest of the way.

2. Replace the dell drawer by sliding it back past the stop.

.........:,@I= 1t_1t QOVe!_S

on sore® modes

Crisper and Convertible Vegetable/Meat Drawers

To Remove and Replace Drawers..

1. Slide crisper or meat drawer straight out to the stop. Lift the

front of drawer with one hand while supporting the bottom
of drawer with the other hand and slide the drawer out the

rest of the way.

2. Replace the crisper or meat drawer by sliding it back in fully
past the drawer stop.

Crisper and Convertible Vegetable/Meat Drawer Covers

To Remove and Replace Covers..

1. Remove the crisper and meat drawer. Pressup in center of

crisper glass insert until it rises above the plastic frame.
Holding the crisper glass firmly, slowly slide the glass insert

forward to remove. Lift crisper cover frame and remove.
Repeat steps to remove the meat drawer cover.

Co_ ve_"lible....."-" ", '_ +Vec e4xsbe,/tec4.@.,,....." ,,,.':_,,,. ".D_'oswe_"

% spe ,x: tu 'e Co ,'4 ot

(o_'ssom_ models)

The convertible vegetable/meat drawer can be adjusted to
properly chill meats or vegetables. The air inside the pan is

cooled to avoid "spot" freezing and can be set to keep meats at
the National Livestock and Meat Board recommended storage
temperatures of 28° to 32°F (-2° to 0°C).

IMPORTANT." To extend freshness, wrap meats in airtight,
moisture-proof materials before storing. Always store meat as

recommended.

Adjusting the Control:

• Move the control to the right (lesscold) or to the left (colder)
as desired.

Meat Vegetables

I I I I I

Temperature Control

To store vegetables.. Set the control to VEGETABLES (all the
way to the right) to store vegetables at their optimal storage

temperatures (which need to be warmer than those for
meat).

IMPORTANT: If food starts to freeze, move the control to the
right (less cold), toward the VEGETABLES setting. Remember to

wait 24 hours between adjustments. Doing so gives the
temperature of the food time to change.

Meat Storage Guide

Store most meat in original wrapping as long as it is airtight
and moisture-proof. Rewrap if necessary. See the following

chart for storage times. When storing meat longer than the
times given, freeze the meat.

Fresh fish or shellfish .......................... use same day as purchased

Chicken, ground beef, variety meat (liver, etc.) ..............1-2 days

Cold cuts, steaks/roasts ...................................................... 3-5 days

Cured meats ....................................................................... 7-10 days

Leftovers - Cover leftovers with plastic wrap, aluminum foil, or
plastic containers with tight lids.

2.

Replace back of meat drawer cover frame into supports or
slides on side walls of the refrigerator and lower or slide the

front of the cover frame into place. Slide rear of glass insert
into cover frame and lower front into place. Repeat steps to

replace the crisper cover.

24

Q'spe " ussdty Co 'st 'o

Fs'eeze " Doo . Bb s

You can control the amount of humidity in the moisture-sealed
crisper. Adjust the control to any setting between FRUIT [-] and

VEGETABLES [+].

Fruit Vegetables

@1 I I I I©

Humidity Control

FRUIT [-] (open) lets moist air out of the crisper for best storage
of fruits and vegetables with skins.

• Fruit. Wash, let dry and store in refrigerator in plastic
bag or crisper. Do not wash or hull berries until they are

ready to use. Sort and keep berries in original container
in crisper, or store in a loosely closed paper bag on a

refrigerator shelf.

• Vegetables with skins: Place in plastic bag or plastic
container and store in crisper.

VEGETABLES [+] (closed) keeps moist air in the crisper for best
storage of fresh, leafy vegetables.

• Leafy vegetables: Wash in cold water, drain and trim or
tear off bruised and discolored areas. Place in plastic

bag or plastic container and store in crisper.

(os s_:wte models ° Access_x'y}

The utility bin can be placed anywhere inside the refrigerator or
freezer. It can be used to hold various small items such as kids'

snacks, or for extra ice storage.
NOTE: For long-term storage, place eggs in a covered container

or in their original carton on an interior shelf.

To Remove and Replace the Bins=

1. Remove the bin by lifting it and pulling it straight out.

2. Replace the bin by sliding it in above the desired supports

and pushing it down until it stops.

F 'eese ' Shelf

sumbe_,. of she yes vaes by _s'_ode }

To Remove and Replace a Shelf=

1. Pull the shelf forward to the stop. Tilt the front of the shelf up
and lift it slightly as you pull the shelf from the frame.

2. Replace the shelf by guiding it back into the slots on the
frame and pushing the shelf in past the stop.

k

! \

FREEZERFEATURES

Your model may have some or all of these features.

Frozen Food Storage Guide

Storage times will vary according to the quality and type of
food, the type of packaging or wrap used (should be airtight

and moisture-proof), and the storage temperature. Ice crystals
inside a sealed package are normal. This simply means that

moisture in the food and air inside the package have
condensed, creating ice crystals.

Put no more unfrozen food into the freezer than will freeze
within 24 hours (no more than 2 to 3 Ibs of food per cubic foot
[907 to 1,350 g per 28 L]of freezer space). Leave enough space

in the freezer for air to circulate around packages. Be certain to
leave enough room for the door to close tightly.

For more information on preparing food for freezing, check a
freezer guide or reliable cookbook.

F_eeze_ Bis_

The freezer bin can be used to store bags of frozen fruits and
vegetables that may slide off freezer shelves.

To Remove and Replace the Freezer Bin=

1. Remove the bin by sliding it out to the stop. Lift the front to

slide the bin out the rest of the way.

2. Replace the bin by positioning it on the rails. Lift the bin
front slightly while pushing it in fully past the stops.

25

REFRIGERATORCARE

Explosion Hazard

Use nonflammable cleaner.
Failure to do so can result in death, explosion, or fire.

Both the refrigerator and freezer sections defrost automatically.
However, clean both compartments about once a month to

avoid buildup of odors. Wipe up spills immediately.
To Clean Your Refrigerator,.

1. Unplug refrigerator or disconnect power.

2. Remove all removable parts from inside, such as shelves,
crispers, etc.

3. Hand wash, rinse, and dry removable parts and interior
surfaces thoroughly. Use a clean sponge or soft cloth and a

mild detergent in warm water.

• Do not use abrasive or harsh cleaners such as window

sprays, scouring cleansers, flammable fluids, cleaning
waxes, concentrated detergents, bleaches or cleansers
containing petroleum products on plastic parts, interior

and door liners or gaskets. Do not use paper towels,
scouring pads, or other harsh cleaning tools. These can

scratch or damage materials.

• To help remove odors, you can wash interior walls with a

mixture of warm water and baking soda (2 tbs to 1 qt
[26 g to 0.95 L] of water).

4. Determine whether your refrigerator exterior is painted
metal, Ultra Satin TM (stainless look) finish, brushed aluminum

or stainless steel, and choose the appropriate cleaning
method.

NOTE= Ultra Satin TM (stainless look) finish has a smooth,
uniform color with a glossy finish that resists fingerprints.

Stainless steel has a distinct grainy texture with variation in
color that is natural to steel.

Painted metal= Wash exteriors with a clean sponge or soft
cloth and a mild detergent in warm water. Do not use

abrasive or harsh cleaners, or cleaners designed for stainless
steel. Dry thoroughly with a soft cloth. Additionally, to avoid

damage to painted metal exteriors, apply appliance wax
(or auto paste wax) with a clean, soft cloth. Do not wax

plastic parts.

Brushed aluminum= Wash with a clean sponge or soft cloth
and a mild detergent in warm water. Do not use abrasive or

harsh cleaners, or cleaners designed for stainless steel. Dry
thoroughly with a soft cloth.

Ultra Satin TM (stainless look) finish: Wash with a clean
sponge or soft cloth and a mild detergent in warm water. Do
not use abrasive or harsh cleaners, or cleaners designed for

stainless steel. Dry thoroughly with a soft cloth.
Stainless steel finish: Wash with a clean sponge or soft cloth

and a mild detergent in warm water. Do not use abrasive or
harsh cleaners. Dry thoroughly with a soft cloth.

To keep your stainless steel refrigerator looking like new
and to remove minor scuffs or marks, it is suggested that

you use the manufacturer's approved Stainless Steel
Cleaner and Polish. To order the cleaner, see

"Accessories."

IMPORTANT: This cleaner is for stainless steel parts only!

Do not allow the Stainless Steel Cleaner and Polish to

come into contact with any plastic parts such as the trim

pieces, dispenser covers or door gaskets. If unintentional

contact does occur, clean plastic part with a sponge and

mild detergent in warm water. Dry thoroughly with a soft

cloth.

5. If your model has a touch screen display on the dispenser
panel, clean the screen using a soft, lint-free cloth. Mix a

mild detergent with water, then use the mixture to dampen
the cloth and gently wipe the screen.

• To avoid unintentionally changing settings, make sure the

refrigerator is unplugged or the power is disconnected
before wiping the screen.

• Do not over-saturate the cloth. Do not spray or wipe

liquids directly onto the screen. Do not use abrasive or
harsh cleaners such as window sprays, scouring

cleansers, flammable fluids, cleaning waxes,
concentrated detergents, nail polish remover, bleaches

or cleansers containing petroleum products. Do not use

paper towels, scouring pads, or other harsh cleaning

tools. These can scratch or damage materials.

6. There is no need for routine condenser cleaning in normal
home operating environments. If the environment is

particularly greasy or dusty, or there is significant pet traffic
in the home, the condenser should be cleaned every 2 to

3 months to ensure maximum efficiency.

If you need to clean the condenser:

• Remove the base grille. See "Base Grille" graphic or

"Base Grille" section.

• Use a vacuum cleaner with a soft brush to clean the

grille, the open areas behind the grille and the front
surface area of the condenser.

26

• Replace the base grille when finished.

7.

Plug in refrigerator or reconnect power.

The interior and dispenser lights are LEDsthat cannot be
changed.

• If the dispenser lights do not appear to be working as
described in "Water and Ice Dispensers" (in the User

Instructions, User Guide, or Use & Care Guide) or if the

interior lights do not illuminate when either door is opened,
call for assistance or service. See either the front cover or

the Warranty for contact information.

If the power will be out for 24 hours or less, keep the door or
doors closed (depending on your model) to help food stay cold

and frozen.
If the power will be out for more than 24 hours, do one of the

following:

• Remove all frozen food and store it in a frozen food locker.
Place 2 Ibs (907 g) of dry ice in the freezer for every cubic

foot (28 L) of freezer space. This will keep the food frozen
for 2 to 4 days.

If neither a food locker nor dry ice is available, consume or

can perishable food at once.

REMEMBER."A full freezer stays cold longer than a partially
filled one. A freezer full of meat stays cold longer than a freezer

full of baked goods. If you see that food contains ice crystals, it
may be refrozen, although the quality and flavor may be

affected. If the condition of the food is poor, dispose of it.

Vacations

If You Choose to Leave Refrigerator On While You Are Away:
I. Use up any perishables and freeze other items.

2. If your refrigerator has an automatic ice maker and is
connected to the household water supply, turn off the water

supply to the refrigerator. Property damage can occur if the
water supply is not turned off.

3. If you have an automatic ice maker, turn off the ice maker.
NOTE: Depending on your model, raise the wire shutoff arm

to OFF (up) position or press the switch to OFF (right).

4. Empty the ice bin.

If You Choose to Turn Refrigerator Off Before You Leave:

1. Remove all food from the refrigerator.

2. If your refrigerator has an automatic ice maker:

• Turn off the water supply to the ice maker at least one
day ahead of time.

• When the last load of ice drops, raise the wire shutoff
arm to the OFF (up) position or move the switch to the

OFF (right) setting.

3. Depending on the model, turn the Refrigerator Control to
OFF or turn cooling off. See "Using the Controls" in the User

Instructions, User Guide, or Use & Care Guide.

4. Clean, wipe, and dry thoroughly.

5. Tape rubber or wood blocks to the tops of both doors to
prop them open far enough for air to get in. This stops odor

and mold from building up.

Moving

When you are moving your refrigerator to a new home, follow
these steps to prepare it for the move.

1. If your refrigerator has an automatic ice maker:

• Turn off the water supply to the ice maker at least one

day ahead of time.

• Disconnect the water line from the back of the

refrigerator.

• When the last load of ice drops, raise the wire shutoff

arm to the OFF (up) position or move the switch to the
OFF (right) setting.

2. Remove all food from the refrigerator and pack all frozen
food in dry ice.

3. Empty the ice bin.

4. Depending on the model, turn the Refrigerator Control to
OFF or turn cooling off. See "Using the Controls" in the User

Instructions, User Guide, or Use & Care Guide.

5. Unplug refrigerator.

6. Clean, wipe, and dry thoroughly.

7. Take out all removable parts, wrap them well, and tape
them together so they don't shift and rattle during the move.

8. Depending on the model, raise the front of the refrigerator
so it rolls more easily OR screw in the leveling legs so they
don't scrape the floor. See "Adjust the Doors" or "Door

Removal, Leveling and Alignment."

9. Tape the doors closed and tape the power cord to the back
of the refrigerator.

When you get to your new home, put everything back and refer
to the Installation Instructions for preparation instructions. Also,

if your refrigerator has an automatic ice maker, remember to
reconnect the water supply to the refrigerator.

27

PROBLEMSOLVER

Firsttry the solutionssuggestedhere or visitourwebsite to possiblyavoid the costof a service call.

Electrical Shack Hazard

Plug inta a graunded 3 prang autlet.
Do not remave graund prang.

Do not use an adapter.
Do nat use an extension card.

Failure to follow these instructians can result in death,

fire, or electrical shack.

GENERAL OPERATION Possible Causes and/or Recommended Solutions
Refrigerator will not operate • Not connected to an electrical supply - Plug the power cord into a grounded 3 prong outlet.

Do not use an extension cord.

Motor seems to run too much •

• No pawer to the electrical outlet - Plug in a lamp to see if the outlet is working.

• Household fuse has blown or circuit breaker has tripped - Replace the fuse or reset the circuit
breaker. If the problem continues, contact a licensed electrician.

• Control or cooling is not turned on - Turn on the refrigerator control, or turn cooling on.
See "Using the Controls."

• New installation - Following installation, allow 24 hours for the refrigerator and freezer to cool

completely.

NOTE= Adjusting the temperature control(s) to the coldest setting will not cool either
compartment (refrigerator or freezer) more quickly.

Your new refrigerator has an energy-efficient motor - The refrigerator may run longer than
you're used to, because the compressor and fans operate at lower speeds that are more

energy-efficient. This is normal.
NOTE= Your refrigerator may run even longer if the room is warm, a large load of food is

added, the doors are opened often, or if a door has been left open.

28

GENERAL OPERATION PossibleCauses and/or Recommended Solutions

Refrigerator seems noisy The compressor in your new refrigerator regulates temperature more efficiently and uses less

energy than older models. During various stages of operation, you may hear normal operating

sounds that are unfamiliar.

The following noises are normal.

• Buzzing/Clicking - Heard when the water valve opens and closes to dispense water or fill the
ice maker. If the refrigerator is connected to a water line, this is normal. If the refrigerator is not

connected to a water line, turn off the ice maker.

• Cracking/Crashing - Heard when ice is ejected from the ice maker mold.

• Popping - Heard when the inside walls contract/expand, especially during initial cooldown.

• Pulsating/Whirring - Heard when the fans/compressor adjust to optimize performance during
normal operation.

Rattling - Heard when water passes through the water line, or due to the flow of refrigerant.
Rattling may also come from items placed on top of the refrigerator.

Water running or gurgling - Heard when ice melts during the defrost cycle and water runs into
the drain pan.

• Sizzling - Heard when water drips onto the heater during the defrost cycle.

Temperature istoo warm New installation - Following installation, allow 24 hours for the refrigerator and freezer to cool

completely.
NOTE. Adjusting the temperature control(s) to the coldest setting will not cool either

compartment (refrigerator or freezer) more quickly.
Doors are opened often or not closed completely - This allows warm air to enter the

refrigerator. Minimize door openings, keep the doors fully closed, and make sure both doors
are properly sealed.

Air vents are blocked - Remove items that are immediately in front of the vents.

Large amount of warm food recently added - Allow several hours for the refrigerator to return
to its normal temperature.

Controls are not set correctly for the surrounding conditions - Adjust the controls to a colder
setting. Check the temperature again in 24 hours.

Temperature istoo cold Controls are not set correctly for the surrounding conditions - Adjust the controls to a warmer

setting. Check the temperature again in 24 hours.
Top refrigerator shelf is colder than lower shelves- On some models, air from the freezer enters

the refrigerator compartment through vents near the top refrigerator shelf. As a result, the top
shelf can be slightly colder than lower shelves.

• Air vents are blocked - Remove items that are immediately in front of the vents.

Interior moisture buildup NOTE" Some moisture buildup is normal. Clean with a soft dry cloth.

• Room is humid - A humid environment contributes to moisture buildup. Use the refrigerator only
in an indoor location, with as little humidity as possible.

• Doors are opened often or not closed completely - This allows humid air to enter the
refrigerator. Minimize door openings, keep the doors fully closed, and make sure both doors

are properly sealed.

Interior lights do not work • Doors have been open for an extended period of time - Close the doors to reset the lights.

• Light bulb is loose in the socket or has burned out - On models with incandescent interior light
bulbs, tighten or replace the bulb. See "Lights."

NOTE: On models with LED lights, call for assistance or service if the interior lights do not
illuminate when either door is opened. See either the front cover or the Warranty for contact

information.

29

GENERAL OPERATION Possible Causes and/or Recommended Solutions
Dispenser lights do not work • Dispenser light isturned off - On some models, if the dispenser light is set to OFF, the light will

(on some models) turn on only when a dispenser pad/lever is pressed. If you want the dispenser light to stay on

continuously, select a different setting. See "Water and Ice Dispensers."

• Dispenser light is set to AUTO or NIGHT LIGHT - On some models, if the dispenser light is set to
AUTO or NIGHT LIGHT, make sure the dispenser light sensor is not blocked. See "Water and
Ice Dispensers."

NOTE: On models with LED lights, call for assistance or service if the dispenser lights do not

operate correctly. See either the front cover or the Warranty for contact information.

Explosion Hazard

Use nonflammable cleaner.
Failure to do so can result in death, explosion, or fire.

DOORS AND LEVELING Possible Causes and/or Recommended Solutions
Doors are difficult to open • Gaskets are dirty or sticky - Clean the gaskets and contact surfaces with mild soap and warm

water. Rinse and dry with a soft cloth.

Doors will not • Door isblocked open - Move food packages away from the door. Make sure all bins and
close completely shelves are in their correct positions. Make sure all packaging materials have been removed.

Doors appear to be uneven • Doors need to be aligned, or refrigerator needs to be leveled - See the leveling and door

alignment instructions.

Refrigerator rocks • Refrigerator is not level - To stabilize the refrigerator, remove the base grille and lower the
and is not stable leveling feet until they touch the floor. See the leveling and door alignment instructions.

3O