Kenmore 10648067895, 10648067894, 10648067893, 10648064894, 10648062895 Owner’s Manual

...

Side by Side Refrigerator

Refrigerador de dos puertas

R6frig6rateur c6te & c6te

Sears Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.

Sears Canada, Inc., Toronto, Ontario, Canada M5B 2B82211833 www.sears.com

TABLE OF CONTENTS

WARRANTY

WARRANTY .................................................................................... 2

REFRIGERATOR SAFETY .......................................................... 3

Proper Disposal of Your Old Refrigerator .................................... 3

INSTALLING YOUR REFRIGERATOR .......................................... 4

Unpacking Your Refrigerator ....................................................... 4

Location Requirements ................................................................ 4

Electrical Requirements ............................................................... 5

Base Grille .................................................................................... 5

Door Removal ............................................................................... 5

Door Closing ................................................................................. 6

Connecting the Refrigerator to a Water Source .......................... 7

Understanding Sounds You May Hear........................................ 8

USING YOUR REFRIGERATOR .................................................... 8

Ensuring Proper Air Circulation .................................................... 8

Setting the Controls ..................................................................... 9

Adjusting Control Settings ........................................................... 9

Ice Maker and Storage Bin/Bucket ............................................ 10

REFRIGERATOR FEATURES ...................................................... 10

Refrigerator Shelves ................................................................... 10

Lateral Adjustable Shelf ............................................................. 11

Flip-up Shelf ............................................................................... 11

Adjustable Flip-up Shelf ............................................................. 11

Deli Drawer ................................................................................. 11

Convertible Vegetable/Meat Drawer, Crisper and Covers ........ 12

Convertible Vegetable/Meat Drawer Temperature Control ....... 12

Crisper Humidity Control ........................................................... 12

Utility or Egg Bin......................................................................... 12

Wine or Can/Bottle Rack ........................................................... 13

FREEZER FEATURES .................................................................. 13

Freezer Shelf .............................................................................. 13

Freezer Basket ........................................................................... 13

DOOR FEATURES ........................................................................ 13

Door Rails ................................................................................... 13

Door Bins.................................................................................... 14

Can Rack.................................................................................... 14

CARING FOR YOUR REFRIGERATOR ....................................... 14

Cleaning Your Refrigerator ......................................................... 14

Changing the Light Bulbs ........................................................... 14

Power Interruptions .................................................................... 15

Vacation and Moving Care ......................................................... 15

TROUBLESHOOTING .................................................................. 16

SEARS MAINTENANCE AGREEMENT ...................................... 18

Accessories ................................................................................ 18

ONE-YEAR FULL WARRANTY ON REFRIGERATOR

For one year from the date of purchase, when this refrigerator is operated and maintained according to instructions attached to or furnished with the product, Sears will repair this refrigerator, free of charge, if defective in material or workmanship.

FIVE-YEAR FULL WARRANTY ON SEALED REFRIGERATION SYSTEM

For five years from the date of purchase, when this refrigerator is operated and maintained according to owner's instructions attached to or furnished with the product, Sears will repair the sealed system (consisting of refrigeration, connecting tubing, and compressor), free of charge, if defective in materials or workmanship.

The above warranty coverage applies only to refrigerators which are used for storage of food for private household purposes and excludes original and replacement Kenmore Filtered Ice & Water filter cartridges (if equipped with the filter system). Original and replacement cartridges are warranted for 30 days, parts only, against defects in material or workmanship.

WARRANTY SERVICE IS AVAILABLE BY CONTACTING THE NEAREST SEARS SERVICE CENTER IN THE UNITED STATES OR CANADA.

This warranty applies only while this product is in use in the United States or Canada. This warranty gives you specific legal rights, and you may also have other rights which vary

from state to state or province to province. Warranty terms may vary in Canada. Contact your local Sears

Service Center for complete details.

Sears, Roebuck and Co.

D/817WA, Hoffman Estates, IL 60179

Sears Canada, Inc., Toronto, Ontario, Canada MSB 2B8

In the space below, record your complete model number, serial number, and purchase date. You can find this information on the

model and serial number label located on the inside wall of the refrigerator compartment.

Have this information available to help you obtain assistance or service more quickly whenever you contact Sears concerning your refrigerator.

Model number 106.

Serial number

Purchase date

Save these instructions and your sales receipt for future reference.

REFRIGERATOR SAFETY

Your safety and the safety of others are very important,

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.

This symbol alerts you to potential hazards that can kill or hurt you and others. All safety messages will follow the safety alert symbol and either the word "DANGER" or

This is the safety alert symbol.

"WARNING." These words mean:

You can be killed or seriously injured if you don't

immediately follow instructions.

You can be killed or seriously injured if you don't

follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

IMPORTANTSAFETYINSTRUCTIONS

WARNING: To reduce the risk of fire, electric shock, or injury when using your refrigerator, follow these basic

precautions:

• Plug into a grounded 3 prong outlet.

• Do not remove ground prong.

• Do not use an adapter.

• Do not use an extension cord.

• Disconnect power before servicing.

• Replace all panels before operating.

• Remove doors from your old refrigerator.

• Use nonflammable cleaner.

• Keep flammable materials and vapors, such as gasoline, away from refrigerator.

• Use two or more people to move and install refrigerator.

• Disconnect power before installing ice maker (on ice maker kit ready models only).

• Use a sturdy glass when dispensing ice or water (on some models).

SAVETHESE INSTRUCTIONS

Proper Disposal of

Your Old Refrigerator

Suffocation Hazard

Remove doors from your old refrigerator. Failure to do so can result in death or

brain damage.

IMPORTANT: Child entrapment and suffocation are not problems of the past. Junked or abandoned refrigerators are still dangerous

- even if they will sit for "just a few days." If you are getting rid of your old refrigerator, please follow these instructions to help prevent accidents.

Before you throw away your old refrigerator or freezer:

• Take off the doors.

• Leave the shelves in place so that children may not easily

climb inside.

INSTALLING YOUR

REFRIGERATOR

Excessive Weight Hazard

Use two or more people to move and install refrigerator.

Failure to do so can result in back or other injury.

Removing packaging materials

• Remove tape and glue from your refrigerator before using. To remove any remaining tape or glue, rub the area briskly

with your thumb. Tape or glue residue can also be easily removed by rubbing a small amount of liquid dish soap over the adhesive with your fingers. Wipe with warm water and dry.

• Do not use sharp instruments, rubbing alcohol, flammable fluids, or abrasive cleaners to remove tape or glue. These products can damage the surface of your refrigerator. For more information, see the "Refrigerator Safety" section.

When Moving "{our Refrigerator: Your refrigerator is heavy. When moving the refrigerator

for cleaning or service, be sure to protect the floor. Always pull the refrigerator straight out when moving it. Do not wiggle or "walk" the refrigerator when trying to move it, as floor damage could occur.

Cleaning before use

After you remove all of the packaging materials, clean the inside of your refrigerator before using it. See the cleaning instructions

in the "Caring for Your Refrigerator" section.

important information to know about glass shelves

and covers:

Do not clean glass shelves or covers with warm water when they are cold. Shelves and covers may break if exposed to sudden temperature changes or impact, such as bumping. For your protection, tempered glass is designed to shatter into many small, pebble-size pieces. This is normal. Glass shelves and covers are heavy. Use special care when re- moving them to avoid impact from dropping.

Explosion Hazard

Keep flammable materials and vapors, such as gasoline, away from refrigerator.

Failure to do so can result in death, explosion, or fire.

To ensure proper ventilation for your refrigerator, allow for V_in. (1.25 cm) space on each side and at the top.

I1,1

/¢

1/2"(1.25

-11- 11

2" (5.08 cm)i

If your refrigerator has an ice maker, make sure you leave some extra space at the back for the water line connections. The refrigerator can be flush against the back wall if you do

not have an ice maker installed.

• If you are installing your refrigerator next to a fixed wall, leave 2 in. (5.08 cm) minimum on each side (depending on your model) to allow for the door to swing open.

NOTE: Do not install the refrigerator near an oven, radiator, or other heat source, nor in a location where the temperature will fall below 55°F (13°C).

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong. Do not use an adapter.

Do not use an extension cord. Failure to follow these instructions can result in

death, fire, or electrical shock.

Before you move your refrigerator into its final location, it is important to make sure you have the proper electrical

connection:

Recommended grounding method

A 115 Volt, 60 Hz., AC only 15 or 20 ampere fused, grounded electrical supply is required. It is recommended that a separate circuit serving only your refrigerator be provided. Use an outlet that cannot be turned off by a switch. Do not use an

extension cord. NOTE: Before performing any type of installation, cleaning, or

removing a light bulb, turn the control, (Thermostat, Refrigerator or Freezer Control depending on the model) to OFF and then disconnect the refrigerator from the electrical source. When you are finished, reconnect the refrigerator to the electrical source and reset the control (Thermostat, Refrigerator or Freezer Control depending on the model) to the desired setting.

To remove the base grille:

1. Open both refrigerator doors.

2. Place hands along the ends of the grille, with your thumbs along the top. Push in with your thumbs and pull up on the

bottom.

NOTE: Be sure to refasten the Tech Sheet behind the base grille after cleaning.

To replace the base grille:

1. Open the doors.

2. Line up the grille support tabs with the metal clips.

3. Push the grille firmly to snap it into place.

TOOLS NEEDED: 1/4in. hex-head socket wrench, s_6 in. hex- head socket wrench and a flat-head screwdriver.

IMPORTANT:

• Before you begin, turn the refrigerator control OFF, unplug refrigerator or disconnect power. Remove food and any adjustable door or utility bins from doors.

• It may only be necessary to remove either the door handle or the doors to get your product through the doorway of your residence. Measure the door opening to determine whether to remove the refrigerator handles or the doors.

Handle Removal (optional)

1. Apply firm pressure with your hand on the face of trim. Slide top trim up and bottom trim down away from handle. Lift trim pieces off shoulder screws (see Graphic 1).

NOTE: Some models include accent pieces between the handle and the handle trim. If your model includes the accents, you will need to carefully remove them with a flat-head screwdriver before removing the handle screws. The accent pieces are optional and can be reinstalled or left off of the handle assembly.

2. Remove handle screws and handles.

3. Move refrigerator into place. Replace handles as shown (see Graphic 1).

Door Removal

1. Unplug refrigerator or disconnect power.

2. Open both refrigerator doors. Remove the base grille by pulling up on the bottom outside corners (see Graphic 2).

3. Close both doors and keep them closed until you are ready to lift them free from the cabinet.

4. Remove top left hinge cover and screws as shown (see Graphic 3). DO NOT REMOVE SCREW 1.

5. Carefully lift freezer door straight up off bottom hinge (see Graphic 4).

6. Remove top right hinge cover and screws as shown (see Graphic 5). DO NOT REMOVE SCREW 1.

7. Carefully lift refrigerator door straight up off bottom hinge (see Graphic 4).

8. It may not be necessary to remove the bottom hinge to move the refrigerator through a doorway. Both bottom hinges have

similar construction.

• Disassemble the hinges as shown (see Graphic 6). DO

NOT REMOVE SCREW 1.

Door and Hinge Replacement

1. Replace both bottom hinges, if removed. Tighten screws.

2. Replace the freezer door by carefully lifting the door onto the bottom left hinge.

NOTE: Provide additional support for the doors while the top hinges are being replaced. Do not depend on the door magnets to hold the doors in place while you are working.

3. Align and replace the top left hinge as shown (see Graphic 3). Tighten screws.

4. Replace left hinge cover.

5. Replace the refrigerator door by carefully lifting the door onto the bottom right hinge.

6. Align and replace the top right hinge as shown (see Graphic 5). Tighten screws.

7. Replace hinge cover.

8. Plug into a grounded 3 prong outlet.

Door Closing

Your refrigerator has two front adjustable rollers -- one on the right and one on the left. If your refrigerator seems unsteady or if you want the doors to close more easily, adjust the refrigerator's tilt using the instructions below:

1. Move the refrigerator into its final position.

2. The two leveling screws are part of the front roller assemblies which are at the base of the refrigerator on either side (see Graphic 7).

3. Use a screwdriver to adjust the leveling screws. Turn the leveling screw to the right to raise that side of the refrigerator or turn the leveling screw to the left to lower that side. It may take several turns of the leveling screws to adjust the tilt of the refrigerator (see Graphic 7).

NOTE: Having someone push against the top of the refrigerator takes some weight off the leveling screws and rollers. This makes it easier to adjust the screws.

4. Open both doors again and check to make sure that they close as easily as you like. If not, tilt the refrigerator slightly more to the rear by turning both leveling screws to the right. It may take several more turns, and you should turn both leveling screws the same amount.

5. Replace the base grille.

NOTE: Be sure to refasten the Tech Sheet behind the base grille.

Door Removal

Top Left Hinge

Style 1

1.Do Not Remove Screw

Base Grille

Top Right Hinge

Style 1

M Handle Removal

(Optional)

1.Do Not Remove Screw

Bottom Hinge

1. Do Not Remove Screw

Door Alignment

1.Leveling Screw

Using a grounded drill, drill a 1/4in. hole in the cold water pipe you have selected.

yfF /

Read all directions carefully before you begin. IMPORTANT:

• If operating the refrigerator before installing the water connection, turn ice maker to the OFF position to prevent operation without water.

• All installations must be in accordance with local plumbing code requirements.

• Use copper tubing and check for leaks.

• Install copper tubing only in areas where temperatures will remain above freezing.

• It may take up to 24 hours for your ice maker to begin producing ice.

Tools required:

• Standard screwdriver

• 7Aein. and 1/2in. open-end wrenches or two adjustable wrenches

• 1/4in. nut driver

• 1/4in. drill bit

• Hand drill or electric drill (properly grounded)

NOTE: Your refrigerator dealer has a kit available with a 1/4in. (6.35 mm) saddle-type shut-off valve, a union, and copper tubing. Before purchasing, make sure a saddle-type valve complies with your local plumbing codes. Do not use a piercing- type or 3Aein. (4.76 mm) saddle valve which reduces water flow and clogs more easily.

Cold water supply The ice maker water valve contains a flow washer which is used

as a water pressure regulator. The ice maker needs to be connected to a cold water line with water pressure between 30 and 120 psi. If a problem occurs, call your utility company.

Connecting to water line:

1. Unplug refrigerator or disconnect power.

2. Turn OFF main water supply. Turn ON nearest faucet long enough to clear line of water.

3. Locate a 1/2in. to 11/4in. (12.7 mm to 3.18 cm) vertical COLD water pipe near the refrigerator.

NOTE: Horizontal pipe will work, but the following procedure must be followed: Drill on the top side of the pipe, not the bottom. This will help keep water away from the drill. This also keeps normal sediment from collecting in the valve.

4. To determine the length of copper tubing you will need, measure from connection on lower left rear of refrigerator to water pipe. Add 7 ft. (2.1 m) to allow for moving refrigerator for cleaning. Use 1/4in. (6.35 mm) O.D. (outside diameter) copper tubing. Be sure both ends of copper tubing are cut square.

7 _" ..............2

1. Cold Water Pipe

2.Pipe Clamp

3. Copper Tubing

4. Compression Nut

5. Compression Sleeve

6. Shut-Qff Valve

7.Packing Nut

6. Fasten shut-off valve to cold water pipe with pipe clamp. Be sure outlet end is solidly in the 1/4in. drilled hole in the water pipe and that washer is under the pipe clamp. Tighten packing nut. Tighten the pipe clamp screws carefully and evenly so washer makes a watertight seal. Do not overtighten or you may crush the copper tubing, especially if soft (coiled) copper tubing is used. Now you are ready to connect the copper tubing.

7. Slip compression sleeve and compression nut on copper tubing as shown. Insert end of tubing into outlet end squarely as far as it will go. Screw compression nut onto outlet end with adjustable wrench. Do not overtighten.

8. Place the free end of the tubing into a container or sink, and turn ON main water supply and flush out tubing until water is clear. Turn OFF shut-off valve on the water pipe. Coil copper tubing.

Connecting to refrigerator:

1. Attach the copper tube to the valve inlet using a compression nut and sleeve as shown. Tighten the compression nut. Do not overtighten. Use the tube clamp on the back of the refrigerator to secure the tubing to the refrigerator as shown. This will help prevent damage to the tubing when the refrigerator is pushed back against the wall. Move to step 2.

2. Turn shut-off valve ON. Check for leaks. Tighten any connections (including connections at the valve) or nuts that

leak.

1. Tube Clamp

2. Copper Tubing

3. Compression Nut

4. Valve Inlet

3. The ice maker is equipped with a built-in water strainer. If local water conditions require periodic cleaning or a well is your source of water supply, a second water strainer should be installed in the 1/4in. (6.35 mm) water line. Obtain a water strainer from your nearest appliance dealer. Install at either

tube connection.

4. Plug in refrigerator or reconnect power.

USING YOUR

REFRIGERATOR

U suc ;:,bnd ° g .;s ou se >

Your new refrigerator may make sounds that your old one didn't make. Because the sounds are new to you, you might be

concerned about them. Most of the new sounds are normal. Hard surfaces, like the floor, walls, and cabinets, can make the sounds

seem louder than they actually are. The following describes the kinds of sounds and what may be making them.

• If your product is equipped with an ice maker, you will hear a buzzing sound when the water valve opens to fill the ice maker for each cycle.

• The defrost timer will click when the automatic defrost cycle begins and ends. Also, the Thermostat Control (or Refrigerator Control depending on the model) will click when cycling on and off.

• Rattling noises may come from the flow of refrigerant, the water line, or items stored on top of the refrigerator.

• Your refrigerator is designed to run more efficiently to keep your food items at the desired temperature. The high efficiency compressor may cause your new refrigerator to run longer than your old one, and you may hear a pulsating or high-pitched sound.

• Water dripping on the defrost heater during a defrost cycle may cause a sizzling sound.

• You may hear the evaporator fan motor circulating the air through the refrigerator and freezer compartments.

• As each cycle ends, you may hear a gurgling sound due to the refrigerant flowing in your refrigerator.

• Contraction and expansion of the inside walls may cause a popping noise.

• You may hear air being forced over the condenser by the condenser fan.

• You may hear water running into the drain pan during the defrost cycle.

i_) " _',;_I"IS,i_,'I% ....... " °_

In order to ensure proper temperatures, you need to permit air to flow between the two sections. Gold air enters the bottom of the

freezer section and moves up. It then enters the refrigerator section through the top vent. Air then returns to the freezer as

shown.

Do not block any of these vents with food such as soda, cereal, bread, etc. If the vents are blocked, airflow will be prevented and the temperature controls will not function properly.

IMPORTANT: Because air circulates between both sections, any odors formed in one section will transfer to the other. You must

thoroughly clean both sections to eliminate odors. To prevent odor transfer from food, wrap or cover foods tightly.

C _ I_,o_,__,_ _ ...... 4

For your convenience, your refrigerator controls are preset at the factory. When you first install your refrigerator, make sure that the controls are still preset. The Refrigerator Control and the

Freezer Control should both be at the "mid-settings" as shown in the illustrations below.

Style 1

FREEZER REFRIGERATOR

n i

COLD COLDER COLD COLDER

Give the refrigerator time to cool down completely before adding food. It is best to wait 24 hours before you put food into the refrigerator. The settings indicated in the previous section should be correct for normal household refrigerator usage. The controls are set correctly when milk or juice is as cold as you like and

when ice cream is firm. If you need to adjust temperatures in the refrigerator or freezer,

use the settings listed in the chart below as a guide. Wait at least 24 hours between adjustments.

RECOMMENDED

CONDITION/REASON: ADJUSTMENT:

NOTE: Your product will not cool when the REFRIGERATOR

Control is set to OFR

Style 2

FREEZER REFRIGERATOR

| |

COLD

8 COLDER COLD

9 1

8 COLDER

NOTE: Your product will not cool when the FREEZER Control is set to OFR

The Refrigerator Control adjusts the refrigerator compartment temperature. Settings to the left of the mid- setting make the temperature less cold. Settings to the right of the mid-setting make the temperature colder.

The Freezer Control adjusts the freezer compartment temperature. Settings to the left of the mid-setting make the temperature less cold. Settings to the right of the mid-setting make the temperature colder.

Give your refrigerator time to cool down completely before adding food. It is best to wait 24 hours before you put food into the refrigerator.

IMPORTANT: If you add food before the refrigerator has cooled completely, your food may spoil. Adjusting the Refrigerator and Freezer Controls to a higher (colder) than recommended setting will not cool the compartments any faster.

REFRIGERATOR section too warm

• Door opened often

• Large amount of food added

• Room temperature very warm

• Air vent blocked by items

FREEZER section too warm/ice not made fast enough

• Door opened often

• Large amount of food added

• Very cold room temperature (can't cycle often enough)

• Heavy ice usage

REFRIGERATOR section

too cold

• Controls not set correctly for your conditions

Adjust REFRIGERATOR

Control one setting higher

For Style 1 controls only: after adjusting control, wait 24

hours and then check the FREEZER

temperature

Move packages out of airstream

Adjust FREEZER Control one setting higher

Adjust REFRIGERATOR

Control one setting lower

For Style 1 controls only: after adjusting control, wait 24

hours and then check the FREEZER

temperature

FREEZER section too cold Adjust FREEZER

• Controls not set correctly for your Control one setting conditions lower

.. Mske B

To turn the ice maker on/off: The on/off switch for the ice maker is a wire shut-off arm located

on the side of the ice maker.

1. To turn the ice maker on, simply lower the wire shut-off arm. NOTE: Your ice maker has an automatic shut-off. As ice is

made, the ice cubes will fill the ice storage bin and the ice cubes will raise the wire shut-off arm to the OFF (arm up) position.

2. To manually turn the ice maker off, lift the wire shut-off arm to the OFF (arm up) position and listen for the click to make sure the ice maker will not continue to operate.

REMEMBER:

• Allow 24 hours to produce the first batch of ice.

• Discard the first three batches of ice produced to avoid impurities that may be flushed out of the system.

• The quality of your ice will be only as good as the quality of the water supplied to your ice maker.

• Avoid connecting the ice maker to a softened water supply. Water softener chemicals (such as salt) can damage parts of the ice maker and lead to poor quality ice. If a softened water supply cannot be avoided, make sure the water softener is operating properly and is well maintained.

• It is normal for the ice cubes to be attached at the corners. They will break apart easily.

• Do not force the wire shut-off arm up or down.

• Do not store anything on top of the ice maker or in the ice storage bin.

To increase ice production rate:

Normal Ice Production: In normal ice production mode, the

ice maker should produce approximately 7 to 9 batches of ice in a 24-hour period. If ice is not being made fast enough, turn the Freezer Control toward a higher (colder) number in half number steps. (For example, if the control is at 3, move it to between 3 and 4.) Wait 24 hours and, if necessary, gradually turn the Freezer Control to the highest setting, waiting 24

hours between each increase. Maximum Ice Production (on some models): In maximum

ice production, the ice maker should produce approximately 10 to 14 batches of ice in a 24-hour period. If your refrigerator has the maximum ice production feature, push the switch to

MAX.

To remove and replace the ice bin:

1. Pull the covering panel out from the bottom and then slide it back toward the rear.

2. Lift the wire shut-off arm so it clicks into the OFF (up) position. Ice can still be dispensed, but no more can be

made.

3. Lift up the front of the storage bin and pull it out.

4. Replace the bin by pushing it in all the way or the dispenser will not work. Push the wire shut-off arm down to the ON

position to restart ice production. Make sure the door is closed tightly.

To care for ice storage bin:

1. Empty the ice bin. Use warm water to melt the ice if necessary. Never use anything sharp to break up the ice in the bin. This can cause damage to the ice container and the dispenser mechanism.

2. Wash ice bin with a mild detergent, rinse well and dry thoroughly. Do not use harsh or abrasive cleaners or solvents.

REFRIGERATOR

FEATURES

Your model may have some or all of these features. Features that can be purchased separately as product accessories are labeled with the word "Accessory." Not all accessories will fit all models. If you are interested in purchasing one of the accessories, please

call the toll-free number on the cover or in the "Assistance or Service" section.

Important information to know about glass shelves

an_ covers:

The shelves in your refrigerator are adjustable to meet your individual storage needs. Your model may have glass or wire shelves.

Storing similar food items together in your refrigerator and adjusting the shelves to fit different heights of items will make

finding the exact item you want easier. It will also reduce the amount of time the refrigerator door is open, and save energy.

Slide-out Shelves (on some models)

• To slide out shelf, carefully pull front of shelf toward you.

• To slide in shelf, push shelf in until it stops.

To remove and replace a shelf in a metal frame:

1. Pull the shelf forward to the stop.

2. Tilt the front of the shelf up and lift it slightly as you pull the shelf from the frame.

3. Replace the shelf by guiding it back into the slots on the frame and pushing the shelf in past the stop.

Shelves and Shelf Frames To remove and replace a shelf/frame:

1. Remove the shelf/frame by tilting it up at the front and lifting it out of the shelf supports.

2. Replace the shelf/frame by guiding the rear shelf hooks into the shelf supports. Tilt the front of the shelf up until rear shelf hooks drop into the shelf supports.

3. Lower the front of the shelf and check to make sure that the shelf is securely in position.

To slide the shelf from side to side:

1. Lift up on the front of shelf and slide to the desired location.

2. Lower shelf to the level position.

NOTE: You do not have to remove small items from the shelf before moving it from side to side. You may need to remove

larger items.

To remove the shelf: NOTE: The shelf is heavy and must be removed using

both hands.

1. Hold the back of the shelf with one hand.

2. Lift the front of the shelf with the other hand to a 45° angle and lower it slightly to release it from the upper channel of the track. Pull the shelf straight out.

To replace the shelf: NOTE: Make sure that both of the rear shelf slides are securely in

the track before letting go of the shelf. The lateral shelf may be difficult to install if the track is placed too close to the refrigerator ceiling. Reposition the track on a lower rung until the shelf can be tilted enough to easily slide into the track.

1. Hold the shelf at the front and tip the front at a 45° angle to the track.

2. Insert both of the rear shelf slides into the upper channel of the track, and lower the front of the shelf into place.

1. To raise the shelf, pull forward on the lever located at the bottom front of the shelf and lift until the shelf locks into the

vertical position.

2. To lower the shelf, lower the shelf until it is latched securely in place.

• e° ....,fAdu beF "

To raise and lower the shelf:

1. Raise the shelf by first sliding it back and down to make it half-width. (You can use the shelf in this position to allow taller items to be stored on the shelf below.)

2. Lift the front of the shelf until it fits securely in place against the back wall.

3. Lower the shelf securely back into position.

4. Pull the front of the shelf forward until it fits into place.

To remove and replace the shelf track:

1. Remove the shelf track by lifting both sides of the track slightly and pulling the track straight out.

2. Replace the track by guiding the track hooks into the shelf support slots on the back wall.

NOTE: Make sure that both sets of track hooks are in the slots and that the slots are parallel with each other.

3. Push the track back and down securely into the shelf supports.

Del Ot_xW,...l

The deli drawer stores raisins, nuts, spreads, and other small items at normal refrigerator temperatures.

To remove and replace the deli drawer:

1. Remove the deli drawer by sliding it straight out to the stop. Lift the front and slide the drawer out the rest of the way.

2. Replace the deli drawer by sliding it back past the stop.

.,_J 6

s¢_s ,_o_ @_ @ % ......_ _

_:>ssome mode@

To remove and replace the crisper and convertible vegetable meat drawers:

1. Slide crisper or meat drawer straight out to the stop. Lift the front of drawer with one hand while supporting the bottom of

drawer with other hand and slide the drawer out the rest of the way.

2. Replace the crisper or meat drawer by sliding it back in fully past the drawer stop.

To remove and replace the crisper or vegetable/meat drawer covers:

1. Remove the crisper and meat drawer. Press up in center of crisper glass insert until it rises above the plastic frame. Holding the crisper glass firmly, carefully slide the glass insert

forward to remove.

2. Lift crisper cover frame up and remove. Repeat steps to remove the meat drawer cover.

3. Replace back of meat drawer cover frame into supports on side walls of the refrigerator and lower the front of the cover frame into place.

4. Slide rear of glass insert into cover frame and lower front into place. Repeat steps to replace the crisper cover.

Meat storage guide

Store most meat in original wrapping as long as it is airtight and moisture-proof. Rewrap if necessary. See the following chart for storage times. When storing meat longer than the times given,

freeze the meat.

Fresh fish or shellfish ................. use same day as purchased

Chicken, ground beef, variety meat (liver, etc.) ......... 1-2 days

Cold cuts, steaks/roasts ........................................... 3-5 days

Cured meats ........................................................... 7-10 days

Leftovers - Cover leftovers with plastic wrap, aluminum foil, or plastic containers with tight lids.

The convertible vegetable/meat drawer can be adjusted to properly chill meats or vegetables. The air inside the pan is

cooled to prevent "spot" freezing and can be set to keep meats at the National Livestock and Meat Board recommended storage

temperatures of 28°- 32°F (-2 °- 0°C).

IMPORTANT: To extend freshness, wrap meats in airtight, moisture-proof materials before storing. Always store meat as

recommended. Adjusting the control

The convertible control comes preset at the lowest meat setting. To change a control setting: Move the control to the right

(colder) or to the left (less cold) as desired. To store vegetables: Set the control at the VEG setting, all the

way to the left, to store vegetables at their optimal storage temperatures (which need to be warmer than those for meat).

IMPORTANT: If food starts to freeze, move the control to the left (less cold). Remember to wait 24 hours between adjustments. Doing so gives the temperature of the food time to change.

Hu dit Cont l

some modets)

You can control the amount of humidity in the moisture-sealed crisper. Adjust the control to any setting between LOW and

HIGH.

• LOW (open) lets moist air out of the crisper for best storage of fruits and vegetables with skins.

Fruit: Wash, let dry and store in refrigerator in plastic bag or crisper. Do not wash or hull berries until they are ready to use. Sort and keep berries in original container in crisper, or store in a loosely closed paper bag on a refrigerator shelf.

Vegetables with skins: Place in plastic bags or plastic container and store in crisper.

• I-II61-1(closed) keeps moist air in the crisper for best storage of fresh, leafy vegetables.

Leafy vegetables: Wash in cold water, drain and trim or tear off bruised and discolored areas. Place in plastic bag or plastic container and store in crisper.

Humidity control location:

• Humidity Control on crisper drawer (Style 1 - on left)

• Humidity Control on crisper cover (Style 2 - on right)

f_ Humidity Control

_c£ some modes _,_Accesso_}

Depending on your model, you may have a one, two or three piece bin. Eggs may be stored in the egg tray or loose in the bin.

NOTE: Store eggs in a covered container for long term storage. If your model does not have an egg storage bin, store eggs in their original carton on an interior shelf.

High 5 4 3 2 1 Low

Wne Can/B e Rack

_ss some modes _J,Acc>!_sso_}

To remove and replace the wine rack (left) or can/bottle rack (right):

1. Remove the rack by pulling it straight out from the shelf.

2. Replace the rack by sliding it in between the shelf and the wall of the refrigerator.

FREEZER FEATURES

call the toll-free number on the cover or in the "Assistance or Service" section.

O_s,mb{_ ' o4's _eBsi_svades wth mede_

To remove and replace the shelf:

1. Lift the shelf off of the supports.

2. Slide it out of the shelf support holes.

3. Replace shelf in the reverse order.

is&

Frozen food storage guide

Storage times will vary according to the quality and type of food, the type of packaging or wrap used (should be airtight and moisture-proof), and the storage temperature. Ice crystals inside a sealed package are normal. This simply means that moisture in the food and air inside the package have condensed, creating ice crystals.

Put no more unfrozen food into the freezer than will freeze within 24 hours (no more than 2-3 Ib of food per cubic foot [907-1,350 g

per L] of freezer space). Leave enough space in the freezer for air to circulate around packages. Be careful to leave enough room for the door to close tightly.

For more information on preparing food for freezing, check a freezer guide or reliable cookbook.

_} ast c bn on some mode@

The freezer basket can be used to store bags of frozen fruits and vegetables that may slide off freezer shelves.

To remove and replace the freezer basket:

1. Remove basket by sliding it out to the stop.

2. Lift the front of the basket and slide it out the rest of the way.

3. Replace the basket by positioning it on the side wall guide rails. Lift the basket front slightly while pushing it past the guide rail stops and slide basket in the rest of the way.

DOOR FEATURES

call the toll-free number on the cover or in the "Assistance or Service" section.

©oo Ras

The door rails may be removed for easier cleaning.

Snap-on Door Rails To remove and replace the rails:

1. Remove the rails by pushing in slightly on the front of the bracket while pulling out on the inside tab. Repeat these steps for the other end of the rail.

2. Replace the rails by aligning the ends of the brackets with the buttons on the sides of the door liner. Firmly snap bracket and rail assembly onto the tabs above the shelf as shown.

Drop-in Door Nails

To remove and replace the rails:

1. Remove the rails by pulling straight up on each end of the rail.

2. Replace the rails by sliding the shelf rail into the slots on the door and pushing the rail straight down until it stops.

Bns

(On s©me node@

To remove and replace the bins:

1. Remove the bin by lifting it up and pulling it straight out.

2. Replace the bin by sliding it in above the desired support and pushing it down until it stops.

Can Back

To remove and replace the rack:

1. Remove the rack by lifting it up and pulling straight out.

2. Replace the rack by holding it above the desired support and

pushing the rack back and down until it stops.

CARING FOR YOUR

REFRIGERATOR

waxes, concentrated detergents, bleaches or cleansers containing petroleum products on plastic parts, interior and door liners or gaskets.

• Do not use paper towels, scouring pads, or other harsh cleaning tools. These can scratch or damage materials.

• To help remove odors, you can wash interior walls with a mixture of warm water and baking soda (2 tbs to 1 qt. [26 g to .95 L] of water).

4. Wash stainless steel and painted metal exteriors with a clean sponge or soft cloth and a mild detergent in warm water. Do not use abrasive or harsh cleaners. Dry thoroughly with a soft

cloth. For additional protection against damage to painted metal

exteriors, apply appliance wax (or auto paste wax) with a clean, soft cloth. Do not wax plastic parts.

5. Clean the condenser coils regularly. Coils may need to be cleaned as often as every other month. This may help save

energy. Style 1 - Condenser coils behind base grille:

• Remove the base grille (see the "Base Grille" section).

• Use a vacuum with an extended attachment to clean the

condenser coils when they are dusty or dirty.

• Replace the base grille when finished. Style 2 - Condenser coils in back of the refrigerator:

• Pull refrigerator out away from the wall (see the

"Unpacking Your Refrigerator" section).

• Vacuum coils when they are dusty or dirty.

• Roll refrigerator back into place. Make sure to leave 1 in.

(2.5 cm) between the cabinet back and the wall.

• Check to see if the refrigerator is level.

6. Plug in refrigerator or reconnect power.

C ea q ge ato

Explosion Hazard

Use nonflammable cleaner.

Failure to do so can result in death, explosion, or fire.

Both the refrigerator and freezer sections defrost automatically. However, clean both sections about once a month to prevent

odors from building up. Wipe up spills immediately.

To clean your refrigerator:

1. Unplug refrigerator or disconnect power.

2. Remove all removable parts from inside, such as shelves, crispers, etc.

3. Hand wash, rinse, and dry removable parts and interior surfaces thoroughly. Use a clean sponge or soft cloth and a

mild detergent in warm water.

• Do not use abrasive or harsh cleaners such as window

sprays, scouring cleansers, flammable fluids, cleaning

NOTE: Not all appliance bulbs will fit your refrigerator. Be sure to replace the bulb with one of the same size and shape. The dispenser light requires a heavy duty 1O-watt bulb. All other lights require a 40-watt appliance bulb. Replacement bulbs are available from your dealer.

1. Unplug refrigerator or disconnect power.

2. Remove light shield when applicable as shown. NOTE: To clean a light shield, wash it with warm water and a

liquid detergent. Rinse and dry the shield well.

3. Remove light bulb and replace with one of the same size, shape and wattage.

4. Replace light shield when applicable as shown.

5. Plug in refrigerator or reconnect power.

Dispenser Light (on some models)

Reach through the dispenser area to remove and replace light bulb.

1. Dispenser Light

Control Panel Light Reach behind the refrigerator control panel to remove and

replace light bulb.

Crisper Light or Upper Freezer Light (on some models)

• Remove light shield by grasping the top center of the shield and pulling forward while turning it slightly to one side. If necessary, remove top crisper drawer to access crisper light

shield. Replace the light shield by inserting the tabs on one end into

the slotted holes in the refrigerator or freezer liner. Then, carefully bend the shield at the center to insert the tabs on

the other end.

Upper Freezer Light (on some models)

• Remove the light shield by grasping the sides and squeezing in towards the center and while pulling forward the shield.

• Replace the light shield by fitting the tabs into the slotted holes in the freezer liner. Push in the shield until it snaps into

place.

Replace the light shield by inserting the tabs on one end into the slotted hole in the freezer liner. Then, carefully bend the

shield at the center to insert the tabs on the other end.

If the electricity in your house goes off, call the power company and ask how long it will be off.

1. If the power will be out for 24 hours or less, keep both refrigerator doors closed to help food stay cold and frozen.

2. If the power will be out for more than 24 hours: a} Remove all frozen food and store it in a frozen food

locker.

b} Place 2 Ibs. (907 g) of dry ice in the freezer for every cubic

foot (28 L) of freezer space. This will keep the food frozen for two to four days.

c} If neither a food locker nor dry ice is available, consume

or can perishable food at once.

REMEMBER: A full freezer stays cold longer than a partially filled one. A freezer full of meat stays cold longer than a freezer full of baked goods. Ifyou see that food contains ice crystals, it may be refrozen, although the quality and flavor may be affected. If the condition of the food is poor, dispose of it.

Lower Freezer Light Beneath Ice Bin (on some models)

• Remove the light shield by grasping the sides and squeezing in towards the center. Once the side hooks of shield are free

from the freezer lining, pull down the shield.

• Replace the light shield by squeezing the sides towards the center and inserting the side hooks into the slotted holes. Once the side hooks are in place, snap the front tab into the

slotted hole.

Lower Freezer Light Behind Top Freezer Basket (on some models)

• Remove the top freezer basket. Remove light shield by grasping the top and bottom center of the shield and pulling

forward while turning it slightly to one side until one of the side tabs become free. Pull out tab from other end and

remove shield.

Vacations If you choose to leave the refrigerator on while you're away,

use these steps to prepare your refrigerator before you leave.

1. Use up any perishables and freeze other items.

2. If your refrigerator has an automatic ice maker:

• Raise wire shut-off arm to OFF (up) position or move the switch to the OFF (right) setting.

• Shut off water supply to the ice maker.

3. Empty the ice bin. If you choose to turn the refrigerator off before you leave,

follow these steps.

1. Remove all food from the refrigerator.

2. If your refrigerator has an automatic ice maker:

• Turn off the water supply to the ice maker at least one day ahead of time.

• When the last load of ice drops, raise the wire shut-off arm to the OFF (up) position or move the switch to the OFF (right) setting.

3. Depending on your model, turn the Thermostat Control or Refrigerator Control to OFF. See the "Setting the Controls"

section.

4. Clean refrigerator, wipe it, and dry well.

5. Tape rubber or wood blocks to the tops of both doors to prop them open far enough for air to get in. This stops odor and mold from building up.

Moving

When you are moving your refrigerator to a new home, follow these steps to prepare it for the move.

1. If your refrigerator has an automatic ice maker:

• Turn off the water supply to the ice maker at least one day ahead of time.

• Disconnect the water line from the back of the refrigerator.

• When the last load of ice drops, raise the wire shut-off arm to the OFF (up) position or move the switch to the OFF (right) setting.

2. Remove all food from the refrigerator and pack all frozen food in dry ice.

3. Empty the ice bin.

4. Depending on your model, turn the Thermostat Control or Refrigerator Control to OFE See the "Setting the Controls"

section.

5. Unplug the refrigerator.

6. Empty water from the defrost pan.

7. Clean, wipe, and dry thoroughly.

8. Take out all removable parts, wrap them well, and tape them together so they don't shift and rattle during the move.

9. Depending on the model, raise the front of the refrigerator so it rolls more easily OR screw in the leveling legs so they don't scrape the floor. See the "Door Closing" or "Leveling Your Refrigerator" section.

10. Tape the doors shut and the power cord to the refrigerator cabinet.

When you get to your new home, put everything back and refer to the "Installing Your Refrigerator" section for preparation instructions. Also, if your refrigerator has an automatic ice maker, remember to reconnect the water supply to the refrigerator.

TROUBLESHOOTING

Try the solutions suggested here first in order to avoid the cost of an unnecessary service call.

Your refrigerator will not operate

• Is the power supply cord unplugged? Plug into a grounded 3 prong outlet.

• Has a household fuse or circuit breaker tripped? Replace the fuse or reset the circuit.

• Is the refrigerator or freezer control turned to the OFF

position? Refer to the "Setting the Controls" section.

• Is the refrigerator defrosting? Recheck to see if the refrigerator is operating in 30 minutes. Your refrigerator will regularly run an automatic defrost cycle.

The lights do not work

• Is the power supply cord unplugged? Plug into a grounded 3 prong outlet.

• Is a light bulb loose in the socket? Turn the refrigerator or freezer control to OFE Disconnect the refrigerator from the electrical supply. Gently remove the bulb and reinsert. Then reconnect the refrigerator to the electrical supply and reset the control.

• Is a light bulb burned out? Replace with an appliance bulb of the same wattage, size, and shape. See the "Changing the Light Bulbs" section.

There is water in the defrost drain pan

• Is the refrigerator defrosting? The water will evaporate. It is normal for water to drip into the

defrost pan.

• Is it more humid than normal? Expect that the water in the defrost pan will take longer to

evaporate. This is normal when it is hot or humid.

The motor seems to run too much

• Is the room temperature hotter than normal? Expect the motor to run longer under warm conditions. At

normal room temperatures, expect your motor to run about 40% to 80% of the time. Under warmer conditions, expect it to run even more of the time.

• Has a large amount of food just been added to the

refrigerator?

Adding a large amount of food warms the refrigerator. It is normal for the motor to run longer in order to cool the

refrigerator back down.

• Is the door opened often? Expect the motor to run longer when this occurs. In order to conserve energy, try to get everything you need out of the refrigerator at once, keep food organized so it is easy to find,

and close the door as soon as the food is removed.

• Are the controls not set correctly for the surrounding

conditions?

Refer to the "Setting the Controls" section.

• Are the doors not closed completely? Push the doors firmly shut. If they will not shut all the way, see "The doors will not close completely" later in this section.

• Are the condenser coils dirty? This prevents air transfer and makes the motor work harder. Clean the condenser coils. Refer to the "Cleaning Your Refrigerator" section.

• Are the door gaskets not sealed all the way around? Contact a qualified person or a technician.

NOTE: If the problem is not due to any of the above, remember that your new refrigerator will run longer than your old one due to its high efficiency motor.

The refrigerator seems to make too much noise

• The sounds may be normal for your refrigerator. Refer to the "Understanding Sounds You May Hear" section.

The ice maker is not producing ice

• Is the freezer temperature not cold enough to produce

ice?

Wait 24 hours after ice maker hook-up for ice production. Refer to the "Setting the Controls" section.

• Is the ice maker wire shut-off arm in the OFF (wire shut-

off arm up) position (on some models)?

Lower wire shut-off arm to the ON (wire shut-off arm down) position. See the "Ice Maker and Storage Bin/Bucket"

section.

• Is the ice maker switch in the OFF (right) position (on

some models)?

Move ice maker switch to the ON (left) position. See the "Ice Maker and Storage Bin/Bucket" section.

• Is the water line shut-off valve to the refrigerator not

turned on?

Turn on the water valve. See the "Connecting the Refrigerator to a Water Source" section.

Is an ice cube jammed in the ice maker ejector arm? For models with an interior ice bin, remove the ice from the

ejector arm with a plastic utensil. For models with an ice bucket located on the freezer door, access the ice maker by

depressing the ice sensor door on the upper left side of the freezer interior. While depressing the sensor door, lift the ice

maker service door and remove the ice from the ejector with a plastic utensil. Refer to the "Ice Maker and Storage Bin/

Bucket" section. Does the ice maker mold have water in it?

Check to see ifyour refrigerator has been connected to your home water supply and the supply shut-off valve is turned on.

Refer to the "Connecting the Refrigerator to a Water Source" section.

NOTE: If not due to any of the above, there may be a problem with the water line. Call for service.

The ice maker is producing too little ice

• Has the ice maker just been installed? Wait 72 hours for full ice production to begin. Once your refrigerator is cooled down, the ice maker should begin producing 70 to 120 cubes every 24 hours.

• Has a large amount of ice just been removed? Allow 24 hours for ice maker to produce more ice.

• Are the controls set correctly? Refer to the "Setting the Controls" section.

Is the water shut-off valve turned completely on?

Turn valve on fully. Refer to the "Connecting the Refrigerator to a Water Source" section.

Is there a water filter installed on the refrigerator? The filter may be clogged or installed incorrectly. First, check

the filter installation instructions to ensure that the filter was installed correctly and is not clogged. If installation or

clogging is not a problem, call a qualified person or a technician.

Off-taste, odor or grey color in the ice

Are the plumbing connections new, causing discolored or off-flavored ice?

Discard the first few batches of ice.

• Have the ice cubes been stored for too long? Throw old ice away and make a new supply.

• Does the freezer and ice bin or bucket need to be cleaned?

See the "Cleaning Your Refrigerator" or "Ice Maker and Storage Bin/Bucket" section.

• Has food in the freezer or refrigerator been wrapped

properly?

Use airtight, moisture-proof packaging to help prevent odor transfer to stored food.

Does the water contain minerals (such as sulfur)? A filter may need to be installed to remove the minerals.

Is there a water filter installed on the refrigerator?

Grey or dark discoloration in ice indicates that the water filtration system needs additional flushing. Run additional water through the water dispenser to flush the water filtration system more thoroughly (at least 2 to 3 gallons or 6 to 7 minutes initially). Discard discolored ice.

The divider between the two compartments is warm

• The warmth is probably due to normal operation of the automatic exterior moisture control. If still concerned, call for service.

Temperature is too warm

• Are the air vents blocked in either compartment? This prevents the movement of cold air from the freezer to the refrigerator. Remove any objects from in front of the air vents. Refer to the "Ensuring Proper Air Circulation" section for the

location of air vents.

Are the door(s) opened often?

Be aware that the refrigerator will warm when this occurs. In order to keep the refrigerator cool, try to get everything you need out of the refrigerator at once, keep food organized so it is easy to find, and close the door as soon as the food is

removed.

• Has a large amount of food just been added to the refrigerator or freezer? Adding a large amount of food warms the refrigerator. It can take several hours for the refrigerator to return to the normal temperature.

• Are the controls set correctly for the surrounding

conditions?

Refer to the "Setting the Controls" section.

+ 39 hidden pages