Kenmore 10004802110, 10004602110, 10004202110 Owner’s Manual

Use & Care Guide Manual de Uso y Cuidado

English / Espa_ol

563140322

nmo

M_<J<',s?',i_od_ o-s

}0 P;802110 - W't_:_/S<_c<

O0 ©4602]10 -.R_diRo}o

P/N 134779000B (0807) Sears Brands Management Corporation

Hoffman Estates, IL 60179 U.S.A. www.kenmore.com

www.sears.com www.kmart.com

10 co"'.-"--0,°

_J %AJ@

0_us

Intertek

Whenusingelectrical appliances, basic safety precautions shoumdalways be

followed, including the following:

1. Read all instructions.

2. To protect against risk of electrical shock do not put Food Processor in water or other liquid.

3. Close supervision is necessary when any appliance isused by or near children.

4. UNPLUG from outlet when not in use, before putting on or taking off parts, and before cleaning.

5. AVOID contact with moving parts.

6. DO NOT operate any appliance with a damaged cord or plug, or after the

appliance malfunctions or has been dropped or damaged in any manner. Return appliance to the nearest authorized service facility for examination, repair or

adjustment.

Z The use of accessory attachments not recommended or sold by the manufacturer

may cause fire, electric shock or personal injury.

8. DO NOT use outdoors.

9. DO NOT let the cord hang over the edge of table or counter.

10. Keep hands and utensils away from moving blades or discs while processing food to reduce the risk of severe injury to persons or damage to the food processor. A scraper may be used but must be used only when the food processor isnot running.

11. Blades are sharp. Handle carefully

12. To reduce the risk of injury, never place cutting blade or discs on base without first putting bowl properly in place.

13. Be certain cover is securely locked in place before operating appliance.

14. NEVER feed food by hand. Always use food pusher.

15. DO NOT attempt to defeat the cover interlock mechanism.

16. Toprotect against electrical shock, this appliance is equipped with a cord having

a 3-prong grounding-type plug for insertion into a proper grounding-type receptacle. DO NOT alter the plug for use in a 2-prong receptacle. If the plug will not fit into a receptacle, have the proper receptacle installed by a qualified electrician.

17. This appliance is for household use only.

Fig. I

Interlock

Control Knob

Slice/Shred Disc

Pusher

Pusher--t Food Pusher Assembly

Chute

Center

I Drive Post

Base

Disc Drive

Adapter Chopping Blade

SAVE THESEiNSTRUCTiONS!

ASSEMBLY cont.

Before using the food processor, wash all parts except the Base in hot, soapy water. Rinse dry. These parts can also be placed in the dishwasher on the top rack. Do not put in or near the utensil basket.

CAUTION: Bladesare sharp. Handle carefully.

CAUTmON:NEVERplace food processor's motor/base in water or other liquids.

NOTE: DO NOT attempt to chop ice in this Food Processor;it will damage the Bowl and dull the Chopping Blade. This unit will not whip cream, beat egg

whites to a desirable volume, grind coffee beans, spices or other items with

high oil content, or slice or shred hardboiled eggs, marshmallows,

or soft cheeses.

IMPORTANT: For your protection, this unit has an interlock system.

Base and Cover is properly locked onto the Bowl. Do not attempt to operate

the unit without the Bowl, Bowl Lid, and Food Chute Lid correctly in place.

ASSEMBLY

Fig. 2a

4. Placethe BowlCoverontothe Bowl.Align the arrowonthe Coverwith the Unlockicon on the Bowl (seeFig.2,2a and 2b). Turnthe Covercounterclockwise

towards the center front until it clicks.

NOTE: There is only one position for the Bowl Cover to lock onto Bowl. The unit will not operate if the Bowl Cover does not lock onto the Bowl, or if the Large Food Pusheris not

inserted intothe Oval Food Chute.

Th_r_ i_ n Fr_r_A PH_h_r A_mhl_ rnn_i_flnn n_ _ Jrlr_ rlnN __mnll PHCh_r Allr.n ÷h_

raised seam running down the back of the Large Pusher with the slot in the Interlock Start Switch. insertthe Large Pusherinto the Oval Food Chute. Then insert the Small

Pusherinto the Circular Food Chute in the Large Pusher.See Fig. 3 and 3a.

Fig. 3

Fig. 3a

1. Make sure the Control Knob is in the OFF position and the power cord isunplugged.

2. Be sure Food Processor base ison a fiat, dry, clean, stable surface before you begin processing.

To assemble, put the Bowl on the Base by aligning the Bowl handle with the Unlock icon on the base. Lock the Bow! onto the Base by turning the Bowl counterclockwise until it clicks into place. Once locked, the Bowl handle will face front and center (see Fig. 1).

NOTE: There is only one position for the Bowl to lock onto the Base. The unit will not

operate if the Bowl does not lock onto the Base.

CONTROLS

CHOPPING cont.

PULSE: When the Control Knob is turned counterclockwise to PULSE and held,

the Food Processor operates. As soon as you let go of the Knob it returns to the OFF position. Use PULSE for short processing tasks, such as chopping nuts,

raw meats or vegetables. This atiows you much greater control of the

consistency of what you are processing. ON: When the Control Knob is turned clockwise to ON,

the unit will run continuously. This is good for less tender food and items that take a while longer to process.

Fig. 4

When you have finished processing, turn the control

knob switch to OFF.

CHOPPING:

1. Lock the Bowl onto the Base as described in Assembly.

2. Place the Chopping Blade onto the Center Post(see Fig. 4).

CAUTION: Blades are sharp. Handle carefully.

Placefood to be chopped into Bowl. Refer to the Chopping Guide to prepare food for chopping.

4. Lock Bowl Cover onto Bowl as described in Assembly.

5. The Control Knob should be in the OFF position. Plug the cord into an electric outlet.

Insert the Food Pusher Assembly as far as it will go

Fig. 5

OFF

down into the Oval Food Chute.

7. Turn the Control Knob to ON to run constantly, or for

Puls_N

better control over consistency, turn and hold knob on PULSE.

When finished processing:

• If Pulsing, release Control Knob and unit automatically stops.

" If you turned processor to ON, turn Control Knob to OFF to stop.

• Allow the chopping blade to stop rotating.

NOTE: Before opening the Bowl Cover,turn the Control Knob to OFF and unplug

the cord.

9. Remove the Food Pusher Assembly from the Processor.

10. To remove bowl cover, unlock by turning clockwise until cover unlatches, and lift off:.

]1. Lift the chopping blade by its base and remove. Unlock the Bowl by turning

it clockwise and lift off:. Empty the processed food.

WARNING: Chopping Blade is very sharp. Use caution when handling. ]

TO SLICE OR SHRED:

unplugged before use. Never use your hand to push food into processor. CAUTION: Make sure control knob switch is turned to OFF and unit is

The use of heavy pressure on the Food Pusher will not speed operation.

1. Lock the Bowl onto the Base as described in Assembly.

Slide the disc drive adapter down onto the center drive post of the base, then

place the slice/shred disc, with the desired side facing up for either slicing or shredding, onto the disc stem and push down. At this point the disc will be at the top of the bowl.

WARNING: Slicing/Shredding Disc is very sharp. Use caution when handling.

3. Lockthe BowlCover onto the Bowl.

Fill Oval or Circular Food Chute with food. See Shredding or Slicing Guide for food piece sizes.

- If using the Large Pusher, fill the Oval Chute with pieces of food such as potato, cabbage, green pepper, whole tomato, etc., up to but not above the Max FiJl line marked on the Chute (see Fig. 6).

- If using the Small Pusher, first remove it from the Large Pusher. Insert the Large Pusher all the way into

the Oval Food Chute. Place food pieces into the Circular Food Chute.

Plug the power cord into a proper

electric outlet.

]

TO SLICEOR SHREDcont.

TO PROCESSLONG AND THiN FOOD ITEMScont.

6. Start Processor.

- If using Large Pusher, make sure that it is joined together with Small Pusher. Insert Pusher into Oval Food Chute to Max Fill line so that Pusher depresses spring in Interlock Start Switch. Turn Control Knob to ON to start Processor. Raise Pusher from Chute to stop Processor.

- If using Small Pusher, Processor will begin running once Control Knob is turned to ON. Use Small Pusher to push food through Circular Chute. TurnControl Knob to OFF to stop Processor.

When food processing is complete, turn Control Knob to OFF, unplug processor,

and wait for disc to stop rotating.

CAUTION: Before opening the Bowl Cover Assembly, be sure you have turned the unit OFF and unplugged the cord.

8. Open bowl cover by turning clockwise, and remove disc with disc stem.

WARNING: Slicing/Shredding Disc is very sharp. Use caution when handling.

9. Unlock Bowl by turning clockwise towards Unlock icon and lift bowl off. Empty the processed food.

TO PROCESSLONG AND THIN FOOD ITEMS

unplugged before use. Never useyour hand to push food into processor.

_ AUTION: Make sure control knob switch is turned to OFF and unit is

The use of heavy pressurewill not speed operation.

Fill the Circular Food Chute with long and thin food items such as pepperoni, carrots or celery.

Insert Small Pusher into Circular Food Chute above food. Plug cord into electrical outlet.

WARNING: Food pusher must always be usedwhen processing food. NEVERuse hand to pushfood directly.

Turn the Control Knob to ON, then press down lightly but firmly on Small Pusher to feed items down and onto slice/shred disc. When the chute is empty, turn the Control Knob to OFF.

When food processing is complete, turn Control Knob to OFF, unplug processor,

and wait for disc to stop rotating.

CAUTION: Before opening the Bowl Cover, turn the unit OFF and unplug the cord.

Take off the bowl cover and carefully lift out disc and disc stem. Unlock Bowl

by turning clockwise towards Unlock icon and lift bowl off. Empty the processed food.

FOOD PROCESSINGTIPS_LIQUIDS

Hot foods and liquids under 176° F can be processed in the bowl. Anything over this temperature is too hot. Be sure to process small amounts of liquids (2 cups or less) at a time. Larger amounts may leak from the bowl.

1. Lock the Bowl onto the Base as described in Assembly.

2. Slide the disc stem down onto the center post of the base, then place the slice/ shred disc, with the desired side facing up for either slicing or shredding, onto the disc stem and push down. At this point the disc wiii be at the top of the bowl.

WARNING: Slicing/Shredding Disc is very sharp. Use caution when handling.

3. Lock bowl cover assembly onto bowl.

4. Remove Small Pusher from Large Pusher. Insert Large Pusher into Oval Food Chute.

+ 9 hidden pages