Kenetics Innovations SR14ABC User Manual

Kenetics Innovations Pte Ltd
SR14+ABC Transit Reader
CSC-RW Technical Manual
Document Number: SR14+ABC-TEC-0001 Version: 1.0 Date: 2009-01-06
Prepared by Reviewed by
Name Seah Chian Jiunn Ow Khiam Beng Signature Date 2009-01-06 2009-01-06
Table of Contents
Section 1: Amendment Record.............................................. 1
1.1 Change Log ....................................................................................... 2
Section 2: Introduction ............................................................ 3
2.1 Purpose................................................................................................ 3
2.2 Abbreviations ..................................................................................... 3
2.3 Terminology ........................................................................................ 3
Section 3: Hardware Specification......................................... 4
3.1 General Hardware Specifications .................................................. 4
3.2 Radio Frequency Interface Specification ..................................... 5
3.3 Physical Dimensions Specifications................................................. 6
3.4 Electrical Specifications.................................................................. 10
3.5 Field Strength Profile of CSC-RW ................................................... 11
Section 4: Operational Precautions ..................................... 12
4.1 General Safety Instructions ............................................................ 12
4.2 Installation ......................................................................................... 13
4.3 Diagnostic Status Indicators........................................................... 13
Section 5: Compliance Statement....................................... 14
Table of Figures
Figure 3.1 General Hardware Specifications........................................................ 4
Figure 3.2 On-board IO Ports Specification......................................................... 4
Figure 3.3
Figure 3.4 Physical Dimensions Specifications ................................................... 6
Figure 3.5 SR14+ABC Reader general outlines................................................... 7
Figure 3.6
Figure 3.7 SR14+ABC Reader Antenna Stackup................................................. 8
Figure 3.8 10 pin connector pin assignment......................................................... 9
Figure 3.9
Figure 3.10 Magnetic Field Strength profile of SR14+ABC Reader................ 11
Figure 4.1 Installation Recommendations.......................................................... 13
Radio Frequency Interface Specification ............................................ 5
SR14+ABC Reader Mechanical Dimensions...................................... 8
Electrical Specifications................................................................... 10
SR14+ABC CSC-RW T
ECHNICAL MANUAL VERSION
1.0 C
ONFIDENTIAL
Section 1: Amendment Record
S/N By Description Date Version
1 Seah Draft Release 2008-11-20 0.1 2 Seah Update for Final Design Documentation 2009-01-06 1.0
1
SR14+ABC CSC-RW T
ECHNICAL MANUAL VERSION
1.1 Change Log
Version 0.1
Initial release.
Values documented in this draft document may not be finalized.
Version 1.0
- Update for final design documentation
1.0 C
ONFIDENTIAL
2
SR14+ABC CSC-RW T
ECHNICAL MANUAL VERSION
1.0 C
ONFIDENTIAL
Section 2: Introduction
2.1 Purpose
The purpose of this document is to document the hardware specification of SR14+ABC reader. SR14+ABC reader is a contact-less smart reader, designed for automatic fare collection purpose.
2.2 Abbreviations
CSC-RW
RF
2.3 Terminology
Main Board Antenna Board
Contact-less Smart Card Reader Writer, use interchangeably with SR14+ABC Radio Frequency
Control board of SR14+ABC Reader Antenna of SR14+ABC Reader
3
SR14+ABC CSC-RW T
ECHNICAL MANUAL VERSION
1.0 C
ONFIDENTIAL
Section 3: Hardware Specification
3.1 General Hardware Specifications
Embedded Processors / Memory CPU Types Dual CPU Architecture, 1 RF CPU & 1 Application CPU.
Secure Application Module ( SAM )
Number of SAMs 4 x SAM Slots
RF Specifications Operating Frequency RF Output Power Up to 0.7 Watt typical. Protocols Supported Reading Range Memory Cards: up to 10cm
Number of Outputs
Figure 3.1 General Hardware Specifications
10 Pin, 2.54mm Pitch Power In 12VDC, RS232, RS485/TTL Mini-USB USB Device
Dimensions 67 x 104 x 18 mm Weight 200 Grams +/- 20 grams
Antenna 1 x Shielded with Ferrite / Spacer Backed, Stackable
Figure 3.2 On-board IO Ports Specification
13.56 MHz (+/- 50 ppm)
ISO 14443-A, B & C
CPU Cards: up to 8.5cm 2 UFL RF Outputs, Multiplexed and Alternating
On Board Ports
Physical Specifications
Antenna Type
4
SR14+ABC CSC-RW T
ECHNICAL MANUAL VERSION
1.0 C
3.2 Radio Frequency Interface Specification
Specification of Radio Frequency Interface
RF Protocol Supported ISO 14443-A, B & C Card Supported All ISO14443-X contactless cards
ONFIDENTIAL
Maximum Communication Range
Logic Card: Up to 10cm
Microprocessor Card: Up to 8.5cm Operating Frequency 13.56MHz RF Output Power Up to 0.7 Watt Typical RF Connector Type U.FL
Figure 3.3 Radio Frequency Interface Specification
5
SR14+ABC CSC-RW T
ECHNICAL MANUAL VERSION
1.0 C
3.3 Physical Dimensions Specifications
Physical Dimension Specifications
ONFIDENTIAL
Connectors
10 pin, 2.54mm pitch right angled, connector
Mini-USB connector Dimensions Control Board with Antenna: 67 x 104 x 18 mm Material PCBA FR4 Board Antenna Separate PCB Antenna Cable Length (between
Approx. 10cm
PCBs ) Operating Temperature Storage Temperature
-10°C to + 70°C (0% - 95% RH, non-condensing )
-20°C to + 85°C (0% - 95% RH, non-condensing) Special Treatment Selective Conformal Coating Reference Figure Figure 3.6
Figure 3.4
Physical Dimensions Specifications
6
SR14+ABC CSC-RW T
ECHNICAL MANUAL VERSION
1.0 C
SR14+ABC Antenna Board
Antenna cable
SR14+ABC Main Board
SR14+ABC Main Board and Antenna Board assembled together
Antenna cable
104 mm
Figure 3.5 SR14+ABC Reader general outlines1
1
Stand-off and screws are not part of DCPS, and deliverables.
J1
ONFIDENTIAL
67 mm 67 mm
>
20 mm
7
SR14+ABC CSC-RW T
ECHNICAL MANUAL VERSION
1.0 C
ONFIDENTIAL
Figure 3.6
SR14+ABC Reader Mechanical Dimensions
Figure 3.7 SR14+ABC Reader Antenna Stackup
8
SR14+ABC CSC-RW T
ECHNICAL MANUAL VERSION
1.0 C
ONFIDENTIAL
Pin 1
Pin 10
10-pin connector – Pin No. Signals
1 Reset Control SHDN 2 Power GND 3
Power
Power Supply (+12V) 4 RX­5 RX+ (TTL-Rx) 6 TX­7
RS485/TTL
TX+(TTL-Tx) 8 TXD 9 Signal Ground
10
Figure 3.8 10 pin connector pin assignment
RS232
RXD
The reader can be reset by in input voltage above 3 volts on pin 1 of the main connector - SHDN. Any high pulse longer than 500ms will trigger the hardware reset.
9
SR14+ABC CSC-RW T
ECHNICAL MANUAL VERSION
1.0 C
ONFIDENTIAL
3.4 Electrical Specifications
Electrical Specifications
Supply Voltage 12V DC +/- 10% regulated Maximum Voltage Ripple 200mVpp Maximum Supply Current 270 mA (@ room temperature & 50ohm-tuned antenna)
Link to Host USB, RS232 and RS485
Figure 3.9
Electrical Specifications
10
SR14+ABC CSC-RW T
ECHNICAL MANUAL VERSION
1.0 C
3.5 Field Strength Profile of CSC-RW
ONFIDENTIAL
Figure 3.10
Min. Reading Field Strength
Magnetic Field Strength profile of SR14+ABC Reader
11
SR14+ABC CSC-RW T
ECHNICAL MANUAL VERSION
1.0 C
ONFIDENTIAL
Section 4: Operational Precautions
4.1 General Safety Instructions
When using the SR14+ABC reader, general safety precautions should always be followed.
1. Handle bare boards with care
2. Only operate the product with the indicated power supply requirement
12
SR14+ABC CSC-RW T
ECHNICAL MANUAL VERSION
1.0 C
ONFIDENTIAL
4.2 Installation
SR14+ABC reader is a contact-less smart card reader, which uses inductive coupling to communicate with contact-less cards. Precaution must be taken to keep the reader far enough from metal surfaces. Refers to table below for general guidelines. Installation of reader near a metal surface may dramatically shorten the operating distance and increase power consumption
Descriptions Clearance
Antenna positioned above metallic
Recommended to be > 20mm away surface (ferrous or non-ferrous metal alike) Any edge or sides of the antenna
Recommended to be > 20mm away against any metal surface (ferrous or non-ferrous metal alike) Any closed loop formed by metal in close proximity to antenna
To be avoided at all times! Especially
within 100mm facing directly parallel to
the antenna top face.
Figure 4.1 Installation Recommendations
Please notice that installation recommendations served as a general guidelines for SR14+ABC reader installation. It does not guarantee the performance to be consistent over every reader installed under different scenarios.
Fine-tuning or adjustment of the antenna may still be required to achieve optimal performance.
4.3 Diagnostic Status Indicators
Conditions Descriptions
LED – All 4 LED ON Performing Power-On Self Test during
Boot-up Any of 4 LED remains ON after Power­ON Self Test
If any of the 4 LEDs remain ON after
Built-in Self Test on Power-Up, there is
error occurred and should be send for
technical troubleshooting.
13
SR14+ABC CSC-RW T
ECHNICAL MANUAL VERSION
1.0 C
ONFIDENTIAL
Section 5: Compliance Statement
This product is currently pending certification for the following compliances:
1. CE
2. FCC
3. EMC: EN61000-6-4: Part 6-4 – Generic Standards – Emission standard for industrial environment
4. EMC: EN61000-6-2: Part 6-2 – Generic Standards – Immunity standard for industrial Environment
Regulatory Notes
An RFID system comprises an RF transmission device, and is therefore subject to national and international regulations. Prior to the powering and operation of the SR14+ABC reader, relevant compliance certificate should be obtained from the associated watchdog agency. Sale, lease or operation in some countries may be subject to prior approval by the respective government body or other international compliance organization.
For operation of radio telecommunication equipment in the European Union or in countries where the CE (Conformité Européene) mark is recognized, Kenetics Innovations, hereby, declares that the SR14+ABC Reader is in compliance with the essential requirements and other relevant provisions of the European Council’s R&TTE directive 1999/5/EC. Note that the SR14+ABC Reader is supplied with its own integral antenna. Users and installers are welcomed to consult the R&TTE directive 1999/5/EC as well as the ETSI EN 302-291-1/2 harmonized standard whether further compliance testing is required if they intend to use their own antenna with SR14+ABC reader control board.
In addition, the length of external cables connected to interface 10 pins of SR14+ABC reader should not exceed 3m. Cable lengths exceeding 3m may not necessarily degrade the performance of the reader but would have to be subject to further compliance test associated with the CE mark. Kenetics will not be liable for cable installations that exceed 3m.
For countries requiring FCC certification, a typical system configuration containing the SR14+ABC reader has been tested and found to be compliant with the limits for a FCC Part 15C (intentional radiator) device. Nonetheless, it is still the responsibility of the customers to have their complete system tested and approved for use from the appropriate compliance agencies/authorities before operating or selling the system. As part of FCC part 15 compliance requirements, it should be noted that:
Modifications not expressly approved by this company could void the user’s
authority to operate the SR14+ABC reader.
The SR14+ABC reader complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) The SR14+ABC reader may not cause harmful interference, and (2) must accept any interference received, including interference that may cause undesired operation.
~~ End Of Document ~~
14
Loading...