Ken-A-Vision T-2400C, T-2600C, T-2200C User Manual

!

CAUTION

Nickel Metal Hydride Battery
Regular charge 8 hours
Do not use non-rechargeable batteries. Only use the NiMH batteries
and power supply/charger provided by Ken-A-Vision. Replacement Power sup­ply - catalog no. VFPS110R-2 (110v) VFPS230R-2
(230v)
Replacement Battery - catalog no. VFBATBU2

Do Not put battery pack in fire or mutilate, battery may burst or
release toxic materials that may cause burns!

WARRANTY:TEN YEAR WARRANTY AGAINST DEFECTIVE PARTS AND WORK­MANSHIP. EXCLUDES BULB AND BATTERY.

Ken-A-Vision has quality technicians on staff to repair or service your micro­scope. Contact us at 1.816.353.4787 for more details.

WARNING

Ken-A-Vision reserves the right to make design improvements and other changes in accordance

with the latest technology. There is no obligation to make changes in products already man-

ufactured. Patents Pending.©2002 Ken-A-Vision Corporation.

KEN-A-VISION MANUFACTURING CO., INC.

5615 Raytown Road, Kansas City, MO 64133 U.S.A Tel. [phone] Fax.

816-358-5072 Email: [e-mail] www.ken-a-vision.com

kav.instcman.cordless704.pc.v2

Part# INS-SC5C

Cordless Vision

Cordless Vision

Supplemental

Instruction Manual

T-2200C Series

T-2400C
T-2600C

INSTRUCTIONS FOR CHARGING YOUR KEN-A-VISION CORDLESS
STEREOSCOPE

1. Plug in the round pin adapter from the power supply to the back of
your stereoscope.

2. Then connect the opposite end to a 110v (220v international)
electrical outlet.

3. With 1 over-night charge you can use your stereoscope for up to 15 hours

of continuous operation.

4.You do not have to fully discharge or drain the battery to recharge.

TECHNICAL SPECIFICATIONS

· Power Source Life: 500 Cycles (approximately 4-5 years depending on usage)

· Light Source: “Propietary Light Board” Technology Equivalent to a
20 Watt Bulb

· Power Source: Built-in rechargeable NiMH (Nickel Metal Hydride)

· “Light Board” Life 100,000 Hours

· Cool Operating Temperature Less Than 25°C (75°F)

· 10 year limited warranty on stereoscope.

ENVIRONMENTAL CONDITIONS

This equipment is designed to be safe at least under the following conditions:

· indoor use;

· altitude up to 2 000 m

· temperature 5° to 40°C;

· maximum relative humidity 80% for temperatures up to 31°C
decreasing linearly to 50% relative humidity at 40°C;

· main supply voltage fluctuations not to exceed +/-- 10% of the
nominal voltage;

· transient overvoltages according to installation categories;

· Pollution Degree 2 in accordance with IEC661

Normally non-conductive pollution occurs. Occasionally, however,

a temporary conductivity caused by condensation must be expected.

EQUIPMENT MAINTENANCE

The battery type is NIMH (Nickel Metal Hydride) part # VFBATBU2
Should you need a replacement power supply/charger, or battery, contact your
nearest Ken-A-Vision dealer.

EQUIPMENT RATING:
DESCRIPTION OF INPUT OUTPUT CONNECTION

Should you need a replacement power supply/charger, contact Ken-A-Vision or
your dealer. When using internationally, be sure to use the correct AC voltage
either 110V, 220V, or 240V output voltage catalog (230v part # VFPS230R-2 or
110v part #VFPS1209300R). Output voltage is 9 volt DC 300mA and a 2.5
mmV barreled styled center position plug. connection of:

The power supply/charger are made exclusively for the Ken-A-Vision Cordless
Stereoscope. Failure to use non-Ken-A-Vision parts will void the warranty of
your stereoscope.

Note: This equipment has been tested and found to comply with the limits for
UL Standard 61010A-1.

kav.instcman.cordless.pc.v2

Part# INS-SC5C

INSTRUCTIONS FOR REPLACEMENT OF CHARGER

Remove the connector cable marked battery from the light board. Next
remove the old NIMHbattery and properly discard.

To replace the NIMH battery simply plug in the cables to the appropriate color
codes as indicated below. Secure the velcro strips to the battery and affix to
the bottom of your stereoscope.

CONNECTOR COLOR CODE