Ken A Vision PrepScope T-1201C, T-1200C, T-2202, T-2202C, PrepScope T-1201 Supplemental Instruction Manual

WARNING

Nickel Metal Hydride Battery
Regular charge 8 hours / Maximum 12.0 hours
Do not use non-rechargeable batteries. Only use the rechargeable
NIMH battery and power supply/charger provided by Ken-A-Vision.
Replacement Power supply - catalog no. VFPS1209300R (110v)
VFPS230R-2 (230v)
Replacement Battery - catalog no. SCBATBU2

Do Not put battery pack in fire or mutilate, battery may burst or
release toxic materials that may cause burns!

WARRANTY:TEN YEAR WARRANTY AGAINST DEFECTIVE PARTS AND WORK­MANSHIP. EXCLUDES BULB AND BATTERY.

Ken-A-Vision has quality technicians on staff to repair or service your micro­scope. Contact us at 1.816.353.4787 for more details.

Cordless PrepScope

Cordless PrepScope

Supplemental

Instruction Manual

T-1201C
T-1202C

KEN-A-VISION MANUFACTURING CO., INC.

5615 Raytown Road, Kansas City, MO 64133 U.S.A Tel. [phone] Fax. 816-358-

5072 Email: [e-mail] www.ken-a-vision.com

kav.instcman.cordless.pc.v2

Part# INS-SC50C

Spring
Loaded Clips

Stage

Light Source

Coarse &Fine
Focus

Objective Lens

4x, 10x, 40x

10x Widefield

Eyepiece

360° Rotating Head

Ken-A-Vision reserves the right to make design improvements and other changes in accordance

with the latest technology. There is no obligation to make changes in products already man-

ufactured. Patents Pending.©2002 Ken-A-Vision Corporation.

!

CAUTION

INSTRUCTIONS FOR CHARGING YOUR KEN-A-VISION
CORDLESS MICROSCOPE

1. Plug in the round pin adapter from the power supply to the back of
your microscope.

2. Then connect the opposite end to a 110v (220v international)

electrical outlet.

3. With 1 over-night charge you can use your microscope for up to 40 hours

of continuous operation.

4.You do not have to fully discharge or drain the battery to recharge.

TECHNICAL SPECIFICATIONS FOR MODEL NO. T-1201C & T­1202C

· Power Source Life: 500 Cycles (approximately 4-5 years depending on usage)

· Light Source: “Propietary Light Board” Technology Equivalent to a
20 Watt Bulb

· Power Source: Built-in rechargeable NiMH (Nickel Metal Hydride)

· “Light Board” Life 100,000 Hours

· Cool Operating Temperature Less Than 25°C (75°F)

· 10 year limited warranty on microscope.

EQUIPMENT RATING:
DESCRIPTION OF INPUT OUTPUT CONNECTION

Should you need a replacement power supply, contact Ken-A-Vision or your deal­er. When using internationally, be sure to use the correct AC voltageeither 110V,
220V, or 240V output voltage (catalog # VFPS230R-2 (230v)or VFPS1209300R
(110v). Output voltage is 9 volt DC 300mA and a 2.5 mmV barreled styled cen­ter position plug. connection of:

The power supply/charger are made exclusively for the Ken-A-Vision Cordless
Microscopes. Failure to use Ken-A-Vision parts will void the warranty of your
microscope.

Note: This equipment has been tested and found to comply with the limits for
UL Standard 61010A-1.

ENVIRONMENTAL CONDITIONS

This equipment is designed to be safe at least under the following conditions:

· indoor use;

· altitude up to 2 000 m

· temperature 5° to 40°C;

· maximum relative humidity 80% for temperatures up to 31°C
decreasing linearly to 50% relative humidity at 40°C;

· main supply voltage fluctuations not to exceed +/-- 10% of the
nominal voltage;

· transient overvoltages according to installation categories;

· Pollution Degree 2 in accordance with IEC661
Normally non-conductive pollution occurs. Occasionally, however,
a temporary conductivity caused by condensation must be expected.

EQUIPMENT MAINTENANCE

All cordless microscopes should be recharged PRIOR to storage.

The battery type is NIMH (Nickel Metal Hydride) part # VFBATBU2
Should you need a replacement power supply/charger, or battery, contact your
nearest Ken-A-Vision dealer.

INSTRUCTIONS FOR REPLACEMENT OF CHARGER

Remove the connector cable marked battery from the light board. Next
remove the old NIMHbattery and properly discard.

To replace the NIMHbattery simply plug in the cables to the appropriate color
codes as indicated below. Secure the velcro strips to the battery and affix to
the bottom of your microscope.

kav.instcman.cordless.pc.v2

Part# INS-SC50C

CONNECTOR COLOR CODE